0603AF

Document 773-1
Ferrite Chip Inductors – 0603AF
• Higher inductance values than ceramic 0603 inductors
•Heavier gauge wire for low DCR
•Ferrite construction for high current handling
•Inductance values from 15 nH to 10 µH
Impedance typ (Ohms)
Inductance2
Part number1
±5% (nH) Q typ3
100 MHz 500 MHz
0603AF-15NXJE_
15 @ 7.9 MHz
0603AF-33NXJE_
33 @ 7.9 MHz
0603AF-47NXJE_
47 @ 7.9 MHz
0603AF-72NXJE_
72 @ 7.9 MHz
0603AF-111XJE_
110 @ 7.9 MHz
0603AF-121XJE_
120 @ 7.9 MHz
0603AF-241XJE_
240 @ 7.9 MHz
0603AF-271XJE_
270 @ 7.9 MHz
0603AF-361XJE_
360 @ 7.9 MHz
0603AF-421XJE_
420 @ 7.9 MHz
0603AF-471XJE_
470 @ 7.9 MHz
0603AF-561XJE_
560 @ 7.9 MHz
0603AF-681XJE_
680 @ 7.9 MHz
0603AF-821XJE_
820 @ 7.9 MHz
0603AF-102XJE_
1000 @ 7.9 MHz
0603AF-152XJE_
1500 @ 7.9 MHz
0603AF-222XJE_
2200 @ 7.9 MHz
0603AF-472XJE_
4700 @ 7.9 MHz
0603AF-103XJE_ 10000 @ 2.5 MHz
13@ 7.9 MHz
13@ 7.9 MHz
13@ 7.9 MHz
15 @ 7.9 MHz
15 @ 7.9 MHz
15 @ 7.9 MHz
15 @ 7.9 MHz
15 @ 7.9 MHz
15@ 7.9 MHz
11@ 7.9 MHz
15 @ 7.9 MHz
16 @ 7.9 MHz
16 @ 7.9 MHz
16 @ 7.9 MHz
17 @ 7.9 MHz
17 @ 7.9 MHz
16 @ 2.5 MHz
16 @ 7.9 MHz
12 @ 2.5 MHz
10
19
42
60
70
76
140
173
210
250
306
371
420
507
663
944
5220
2100
1400
1. When ordering, please specify termination and packaging codes:
0603AF-102XJEW
Termination:E=Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations.
Special order:
R = RoHS compliant matte tin over nickel over
silver-platinum-glass frit
Q = RoHS tin-silver-copper (95.5/4/0.5) or
P = non-RoHS tin-lead (63/37).
Packaging:W
=7″ machine-ready reel. EIA-481 punched paper tape
(2000 parts per full reel).
U=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter W instead.
2. Inductance measured at 0.1 Vrms, using Coilcraft SMD-A fixture
in Agilent/HP 4286A impedance analyzer with Coilcraft-provided
correlation pieces.
3. Q measured on Agilent/HP 4395A with Agilent/HP 16193 test fixture.
4. SRF measured using Agilent/HP 8753D network analyzer with
Coilcraft SMD‑D test fixture.
5. DCR measured on Cambridge Technology Micro-ohmmeter.
6. Current that causes a 15°C temperature rise from 25°C ambient.
Because of their open construction, these parts will not saturate. This
information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
typ4 DCR max5 Irms6Color
(MHz)
(Ohms)
(A)
code
SRF
42
90
210
385
350
410
810
1023
1310
1925
2253
3180
3620
3300
9823
17,830
129
220
150
3500
2300
2250
1800
1230
1150
900
750
700
685
575
515
530
325
400
330
85
60
40
0.023
0.028
0.052
0.065
0.060
0.089
0.12
0.22
0.21
0.33
0.37
0.49
0.46
0.58
0.84
1.30
1.10
1.50
4.50
2.1
1.9
1.7
1.5
1.6
1.4
0.85
0.68
0.65
0.61
0.61
0.53
0.49
0.42
0.40
0.28
0.32
0.26
0.18
Yellow
Red
White
Blue
Red
Black
Violet
Brown
Blue
Red
Orange
Blue
Orange
Green
Black
Orange
Red
Yellow
Gray
Designer’s Kit C439 contains 10 each of all values
Core material Ferrite
Environmental RoHS compliant, halogen free
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost
Weight 4.3 – 5.7 mg
Ambient temperature –40°C to +85°C with Irms current
Maximum part temperature +100°C (ambient + temp rise) Derating.
Storage temperature Component: –40°C to +100°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +50 to +300 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 2000 per 7″ reel; Paper tape: 8 mm wide, 1.0 mm thick,
4 mm pocket spacing
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 773-1 Revised 10/12/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Document 773-2
Ferrite Chip Inductors – 0603AF Series
Typical L vs Frequency
Typical Q vs Frequency
Typical Impedance vs Frequency
C
B
overall
D
F
A
E
terminal
H
Pick and
place
material
I
G
J
F
I
Terminal wraparound:
approx 0.008/0,20 both ends
Recommended
Land Pattern
ABCD
maxmaxmax ref E F G H IJ
0.0710.0440.0360.0150.0300.0130.0340.0400.0250.025inches
1,801,120,910,380,760,330,861,020,640,64
mm
Note: Height dimension (C) is before optional solder application. For maximum
height dimension including solder, add 0.006 in / 0,152 mm.
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 773-2 Revised 10/12/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.