Document 781-1 Ferrite Chip Inductors – 0805AF (2012) •Higher inductance values than ceramic 0805 inductors •Inductance values from 0.11 µH to 22 µH •Heavier guage wire for low DCR •Ferrite construction for high current handling Inductance2 Part number1 ±5% (µH) Q typ3 Impedance typ (Ohms) 0805AF-111XJR_ 0805AF-681XJR_ 0805AF-102XJR_ 0805AF-122XJR_ 0805AF-152XJR_ 0805AF-182XJR_ 0805AF-222XJR_ 0805AF-272XJR_ 0805AF-332XJR_ 0805AF-472XJR_ 0805AF-682XJR_ 0805AF-103XJR_ 0805AF-153XJR_ 0805AF-223XJR_ 370 @ 500MHz 430 @ 100 MHz 670 @ 100 MHz 860 @ 100 MHz 1000 @ 100 MHz 1360 @ 100 MHz 840 @ 50 MHz 1050 @ 50MHz 1670 @ 50 MHz 950 @ 25 MHz 450 @ 10MHz 740 @ 10 MHz 1300 @ 10MHz 1620 @ 10 MHz 0.11 @ 7.9 MHz 0.68 @ 7.9 MHz 1.0 @ 7.9 MHz 1.2 @ 7.9 MHz 1.5 @ 7.9 MHz 1.8 @ 7.9 MHz 2.2 @ 7.9 MHz 2.7 @ 7.9 MHz 3.3 @ 7.9 MHz 4.7 @ 7.9 MHz 6.8 @ 7.9 MHz 10 @ 2.5 MHz 15 @ 2.5 MHz 22 @ 2.5 MHz 18 @ 7.9 MHz 19 @ 7.9 MHz 17 @ 7.9 MHz 19 @ 7.9 MHz 20 @ 7.9 MHz 20 @ 7.9 MHz 19 @ 7.9 MHz 19 @ 7.9 MHz 19 @ 7.9 MHz 18 @ 7.9 MHz 18 @ 7.9 MHz 18 @ 2.5 MHz 17 @ 2.5 MHz 17 @ 2.5 MHz 1. When ordering, please specify termination and packaging codes: 0805AF-103XJRC Termination:R=RoHS compliant matte tin over nickel over silverplatinum-glass frit. Special order: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37). Packaging:C =7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. 2. Inductance measured at 0.1 Vrms, using Coilcraft SMD-A fixture in Agilent/HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Q measured on Agilent/HP 4395A with Agilent/HP 16193 test fixture. 4. SRF measured using Agilent/HP 8753D network analyzer with Coilcraft SMD‑D test fixture. 5. DCR measured on Cambridge Technology Micro-ohmmeter. 6. Current that causes a 15°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. typ4 DCR max5 Irms6Color (MHz) (Ohms) (mA)code SRF 1260 425 355 375 285 300 105 100 85 55 37 26 20 21 0.05 0.30 0.39 0.64 0.74 0.98 0.98 1.16 1.20 1.50 1.90 2.20 4.25 6.70 940 660 650 440 390 370 350 320 330 280 240 230 150 120 Brown Orange Yellow Brown Green Blue Brown Violet Gray Black Brown Red Yellow Green Designer’s Kit C450 contains 10 of each value Core material Ferrite Environmental RoHS compliant without exemption, halogen free Terminations RoHS compliant matte tin over nickel over silverplatinum-glass frit. Other terminations available at additional cost. Weight 16.7 – 18.0 mg Ambient temperature –40°C to +85°C with Irms current Maximum part temperature +100°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000/7″reel; Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.65 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Document 781-1 Revised 10/12/15 Document 781-2 Ferrite Chip Inductors – 0805AF Series Typical L vs Frequency Typical Q vs Frequency 100 30 22 µH 25 6.8 µH 4.7 µH 3.3 µH 2.7 µH 2.2 µH 10 22 µH 20 1.5 µH 1.0 µH 0.68 µH Q Factor Inductance (µH) 10 µH 1 0.11 µH 6.8 µH 0.68 µH 2.2 µH 3.3 µH 1.5 µH 4.7 µH 1.0 µH 10 µH 2.7 µH 15 10 5 0.11 µH 0.1 1 100 10 0 1000 1 D F A 0.11 µH 1.5 µH 1.0 µH 0.68 µH 22 µH 10 µH 6.8 µH 4.7 µH 3.3 µH 2.7 µH 2.2 µH Impedance (kOhms) C B overall 1000 10 E terminal H Pick and place material I G J F I Terminal wraparound: approx 0.008/0,20 both ends Recommended Land Pattern ABCD maxmaxmax ref E F G H IJ 0.0900.0680.0600.0200.0500.0160.0400.0700.0400.030inches 2,291,731,520,511,270,411,021,781,020,76 mm 1 0.1 0.01 1000 Frequency (MHz) Typical Impedance vs Frequency 100 100 10 Frequency (MHz) Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. 0.001 0.01 0.1 1 10 Frequency (GHz) Document 781-2 Revised 10/12/15