NT E R R U C H HIG Document 218-1 Chip Inductors – 0603HC (1608) With their high current ratings and ultra-small size, these chip inductors are ideal for today’s high frequency, low voltage applications like mobile phones. They feature continuous current ratings up to 2.4 Amps DC and will handle transient currents up to 50% higher. At low inductance values, their Q factors are also higher than our 0603CS Series. SRFDCR min5 max6 Irms7Color 900 MHz 1.7 GHz Inductance2Percent Q tolerance3 min4 Part number1(nH) L typ Q typ L typ Q typ (MHz) (Ohms) (A) code 0603HC-1N6XJL_1.6 5 24 1.6749 1.65 63 12500 0.030 2.4 Black 0603HC-3N6XJL_3.6 5 24 3.6570 3.75 90 5900 0.048 2.3Brown 0603HC-3N9XJL_3.9 5 25 3.7470 3.90 90 5900 0.054 2.2 Red 0603HC-6N8XJL_6.8 5 35 6.72 70 7.10 75 5800 0.054 2.1Orange 0603HC-7N5XJL_7.5 5 38 7.3370 7.90 68 3700 0.059 2.1Yellow 0603HC-10NX_L_10 5,2 38 9.7073 10.5 57 3700 0.071 2.0Green 0603HC-12NX_L_12 5,2 38 12.3 68 14.5 41 30000.0752.0 Blue 0603HC-15NX_L_15 5,2 38 15.5 65 17.6 40 2800 0.080 1.9Violet 0603HC-18NX_L_18 5,2 40 19.5 62 25.0 40 28000.0991.9Gray 0603HC-22NX_L_22 5,2 42 24.0 61 31.5 26 2400 0.099 1.8White 0603HC-24NX_L_24 5,2 42 25.8 55 35.0 21 2400 0.105 1.8Black 0603HC-33NXJL_33 5 47 34.3 50 — — 1900 0.175 0.95Brown 0603HC-47NXJL_47 5 40 49.5 45 — — 1530 0.195 0.85Red 1. When ordering, specify tolerance, termination and packaging codes: 0603HC-24NXJLW Tolerance: G=2% J = 5% (Table shows stock tolerances in bold.) Termination:L=RoHS compliant silver-palladium-platinum-glass frit. E=Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:W =7″ machine-ready reel. EIA-481 punched paper tape (2000 parts per full reel). U=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter W instead. 2. Inductance measured at 250 MHz using Coilcraft SMD-A fixture in Agilent/HP 4286 impedance analyzer with Coilcraft-provided correlation pieces. 3. Tolerances in bold are stocked for immediate shipment. 4. Q measured at 250 MHz using Agilent/HP 4291A with Agilent/ HP 16193 test fixture. 5. SRF measured using Agilent/HP 8720D network analyzer and Coilcraft SMD-D test fixture. 6. DCR measured on micro-ohmmeter and Coilcraft CCF858 test fixture. 7. Current that causes a 20°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Designer’s Kit C339 contains 10 of each of all 5% parts Core material Ceramic Environmental RoHS compliant, halogen free optional Terminations RoHS compliant silver-palladium-platinum-glass frit. Weight 3.3 – 3.7 mg Ambient temperature –40°C to +125°C with Irms current Maximum part temperature +145°C (ambient + temp rise). Storage temperature Component: –40°C to +145°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +25 to +125 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000 per 7″ reel. Paper tape: 8 mm wide, 1.0 mm thick, 4 mm pocket spacing PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Document 218-1 Revised 10/12/15 Document 218-2 NT E R R U C H HIG 0603HC (1608) Chip Inductors Typical Q vs Frequency Typical L vs Frequency 100 6.8 nH 30 5.6 nH 3.6 90 22 nH 15 nH 80 60 Inductance (nH) Q Factor 70 22 nH 50 40 30 20 15 nH 10 6.8 nH 20 3.6 nH 10 0 0 1 10 100 10000 1000 C B overall A E terminal 10 100 1000 10000 H D F 1 Frequency (MHz) Frequency (MHz) Pick and place material I G J F I Terminal wraparound: approx 0.008/0,20 both ends Recommended Land Pattern ABCD maxmaxmax ref E F G H IJ 0.0710.0440.0400.0150.0300.0130.0340.0400.0250.025inches 1,801,121,020,380,760,330,861,020,640,64 mm Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. Document 218-2 Revised 10/12/15