0805HT

Document 168-1
Chip Inductors – 0805HT (2012)
At just 0.035″ high, these are one of our lowest profile
surface mount inductors. Their wire wound ceramic design provides tight tolerances, exceptional Q and high
SRF values.
Coilcraft Designer’s Kit C321 contains samples of all
5% parts shown as stocked. To order, contact Coilcraft
or visit http://order.coilcraft.com to purchase on-line.
SRF min5 Percent
DCR max6 Irms7
Color
Q min4
(MHz) (Ohms)(mA) Code
Part number1
Inductance2
(nH)
tolerance3
0805HT-1N8TJL_
0805HT-2N0TJL_
0805HT-3N9TJL_
0805HT-4N3TJL_
0805HT-4N7TJL_
0805HT-5N1TJL_
0805HT-5N6TJL_
0805HT-6N8TJL_
0805HT-7N5TJL_
0805HT-8N2TJL_
0805HT-9N1TJL_
0805HT-10NT_L_
0805HT-12NT_L_
0805HT-15NT_L_
0805HT-18NT_L_
0805HT-20NT_L_
0805HT-22NT_L_
0805HT-27NT_L_
0805HT-33NT_L_
0805HT-39NT_L_
0805HT-47NT_L_
0805HT-56NT_L_
0805HT-68NT_L_
0805HT-82NT_L_
0805HT-R10T_L_
0805HT-R12T_L_
0805HT-R15T_L_
0805HT-R18T_L_
0805HT-R22T_L_
0805HT-R27T_L_
0805HT-R33T_L_
0805HT-R39T_L_
0805HT-R47T_L_
0805HT-R50T_L_
1.8@ 250 MHz
2.0@ 250 MHz
3.9@ 250 MHz
4.3@ 250 MHz
4.7@ 250 MHz
5.1@ 250 MHz
5.6@ 250 MHz
6.8@ 250 MHz
7.5@ 250 MHz
8.2@ 250 MHz
9.1@ 250 MHz
10@ 250 MHz
12@ 250 MHz
15@ 250 MHz
18@ 250 MHz
20@ 250 MHz
22@ 250 MHz
27@ 250 MHz
33@ 250 MHz
39@ 250 MHz
47@ 200 MHz
56@ 200 MHz
68@ 200 MHz
82@ 150 MHz
100@ 150 MHz
120@ 150 MHz
150@ 150 MHz
180@ 150 MHz
220@ 150 MHz
270@ 150 MHz
330@ 150 MHz
390@ 100 MHz
470@ 100 MHz
500@ 50 MHz
5
5
5
5
5
5
5
5
5
5
5
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2,1
5,2,1
5,2,1
5,2,1
5,2,1
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
55 @ 1500 MHz
55 @ 1500 MHz
50 @ 1000 MHz
80 @ 1000 MHz
50 @ 1000 MHz
45 @ 1000 MHz
45 @ 1000 MHz
50 @ 1000 MHz
47 @ 1000 MHz
50 @ 1000 MHz
54 @ 1000 MHz
55 @ 750 MHz
55 @ 750 MHz
50 @ 500 MHz
50 @ 500 MHz
50 @ 500 MHz
50 @ 500 MHz
50 @ 500 MHz
55 @ 500 MHz
55 @ 500 MHz
50 @ 500 MHz
50 @ 500 MHz
50 @ 500 MHz
50 @ 500 MHz
50 @ 500 MHz
40 @ 250 MHz
40 @ 250 MHz
40 @ 250 MHz
39 @ 150 MHz
33 @ 150 MHz
32 @ 150 MHz
30 @ 150 MHz
30 @ 150 MHz
20 @ 50 MHz
1. When ordering, specify tolerance, termination and packaging codes:
0805HT-R22TGLC
Termination:L =RoHS compliant silver-palladium-platinum-glass frit.
E=Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Tolerance: F=1% G = 2% J = 5%
(Table shows stock tolerances in bold.)
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (7500 parts per
full reel).
9400
11500
6100
6364
5500
6100
5800
4800
4600
4800
3900
3300
3800
2950
3100
2700
2900
2450
2350
2200
2000
1850
1500
1500
1200
1150
1050
830
820
790
730
675
610
585
0.030
0.018
0.055
0.030
0.060
0.069
0.091
0.080
0.082
0.080
0.105
0.080
0.10
0.10
0.13
0.17
0.15
0.19
0.19
0.27
0.30
0.39
0.40
0.44
0.64
0.68
0.80
0.86
1.29
1.40
1.93
2.80
3.10
3.20
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
700
600
600
600
500
500
500
400
300
300
300
200
200
200
200
200
200
Black
Violet
Brown
White
Red
Blue
Gray
Orange
Black
Yellow
Red
Green
Blue
Violet
Gray
Yellow
White
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Gray
White
Black
Orange
Yellow
Green
Blue
Violet
Gray
2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/HP
4286A impedance analyzer with Coilcraft-provided correlation pieces.
3. Tolerances in bold are stocked for immediate shipment.
4. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test
fixture and on an Agilent/HP 8753D with a Coilcraft SMD-D test fixture.
5. SRF measured using an Agilent/HP 8720D network analyzer and a
Coilcraft SMD-D test fixture.
6. DCR measured on a Cambridge Technology micro-ohmmeter and a
Coilcraft CCF858 test fixture.
7. Current that causes a 15°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute maximum ratings.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 168-1 Revised 10/12/15
Document 168-2
0805HT Series (2012)
Typical Q vs Frequency
Typical L vs Frequency
120
12 nH
100
3.9 nH
150 nH
150
Inductance (nH)
39 nH
80
Q factor
200
22 nH
120 nH
60
40
100
82 nH
50
33 nH
20
18 nH
0
3.9 nH
0
10
1000
100
10000
1
10
B
overall
H
C
E
terminal
1000
10000
Designer’s Kit C321 contains samples of all 5% tolerance parts
Core material Ceramic
I
Environmental RoHS compliant, halogen free optional
G
J
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
F
I
F
A
Pick and
place
material
100
Frequency (MHz)
Frequency (MHz)
Terminal wraparound:
approx 0.010/0,25 both ends
Recommended
Land Pattern
A B C
max max max E
F
G
H
IJ
0.0850.0600.0350.0500.0170.0450.0700.0400.030 inches
2,161,520,891,270,431,141,781,020,76mm
Note: Height dimension (C) is before optional solder application. For maximum
height dimension including solder, add 0.006 in / 0,152 mm.
Weight 6.0 – 6.9 mg
Ambient temperature –40°C to +125°C with Irms current
Maximum part temperature +140°C (ambient + temp rise).
Storage temperature Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +25 to +125 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 2000/7″ reel; 7500/13″ reel; Plastic tape: 8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 0.9 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Document 168-2 Revised 10/12/15