0805LS

Document 288-1
Chip Inductors – 0805LS (2012)
These ferrite core surface mount inductors have lower
DCR and higher current ratings than our 0805CS Series.
They come in inductance values from 0.078 to 27 µH.
Coilcraft Designer’s Kit C354 contains samples of all
5% inductance tolerance parts. To order, contact Coilcraft
or visit http://order.coilcraft.com to purchase on-line.
Inductance2
Irms6Color
Percent SRF min4 DCR max5
Q min3 (MHz) (Ohms) (A)code
Part number1 (µH)tolerance
0805LS-78NX_L_
0.078 @ 7.9 MHz
0805LS-111X_L_
0.110 @ 7.9 MHz
0805LS-471X_L_
0.470 @ 7.9 MHz
0805LS-681X_L_
0.680 @ 7.9 MHz
0805LS-102X_L_ 1.0 @ 7.9 MHz
0805LS-122X_L_ 1.2 @ 7.9 MHz
0805LS-152X_L_ 1.5 @ 7.9 MHz
0805LS-182X_L_ 1.8 @ 7.9 MHz
0805LS-222X_L_ 2.2 @ 7.9 MHz
0805LS-272X_L_ 2.7 @ 7.9 MHz
0805LS-332X_L_ 3.3 @ 7.9 MHz
0805LS-392X_L_ 3.9 @ 7.9 MHz
0805LS-472X_L_ 4.7 @ 7.9 MHz
0805LS-682X_L_ 6.8 @ 7.9 MHz
0805LS-822X_L_ 8.2 @ 2.5 MHz
0805LS-103X_L_ 10.0 @ 2.5 MHz
0805LS-153X_L_ 15.0 @ 2.5 MHz
0805LS-223X_L_ 22.0 @ 2.5 MHz
0805LS-273X_L_ 27.0 @ 2.5 MHz
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
5,2
19 @ 7.9 MHz
19 @ 7.9 MHz
19 @ 7.9 MHz
20 @ 7.9 MHz
20 @ 7.9 MHz
15 @ 7.9 MHz
20 @ 7.9 MHz
20 @ 7.9 MHz
20 @ 7.9 MHz
20 @ 7.9 MHz
20 @ 7.9 MHz
20 @ 7.9 MHz
20 @ 7.9 MHz
20 @ 7.9 MHz
18 @ 2.5 MHz
18 @ 2.5 MHz
18 @ 2.5 MHz
18 @ 2.5 MHz
15 @ 2.5 MHz
1440
1200
500
400
340
280
275
246
106
105
83
52
50
35
27
21
17
13
11
0.042
0.05
0.31
0.46
0.69
1.20
1.03
1.15
1.28
1.48
1.57
1.70
1.87
2.25
2.55
3.45
5.03
6.18
11.04
2.0
2.0
0.720
0.590
0.500
0.400
0.490
0.410
0.365
0.350
0.330
0.300
0.280
0.260
0.250
0.200
0.180
0.150
0.120
Black
Brown
Red
Orange
Yellow
Brown
Green
Blue
Brown
Violet
Gray
White
Black
Brown
Red
Orange
Yellow
Green
Blue
1. When ordering, specify tolerance, termination and packaging codes:
Core material Ceramic/Ferrite
0805LS-273XJLC
Tolerance: G=2% J = 5%
(Table shows stock tolerances in bold.)
Termination:L=RoHS compliant silver-palladium-platinum-glass frit.
E=Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/
HP 4286A impedance analyzer with Coilcraft-provided correlation
pieces.
3. Q measured on an Agilent/HP 4291A with an Agilent/HP 16193 test
fixture.
4. SRF measured using an Agilent/HP 8753D network analyzer with a
Coilcraft SMD-D test fixture.
5. DCR measured on a Cambridge Technology Micro-ohmmeter.
6. Current that causes a 15°C temperature rise from 25°C ambient.
Because of their open construction, these parts will not saturate. This
information is for reference only and does not represent absolute
maximum ratings.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Environmental RoHS compliant, halogen free optional
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 12.7 – 13.9 mg
Ambient temperature –40°C to +85°C with Irms current
Maximum part temperature +100°C (ambient + temp rise).
Storage temperature Component: –40°C to +100°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +100 to +250 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 2000/7″reel; Plastic tape: 8 mm wide, 0.23 mm thick,
4 mm pocket spacing, 1.6 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Document 288-1 Revised 10/12/15
Document 288-2
0805LS Series Chip Inductors
Typical L vs Frequency
Typical Q vs Frequency
100
35
27 µH
10
3.3 µH
25
3.3 µH
10 µH
Q factor
Inductance (µH)
30
10 µH
1 µH
1
0.110 µH
0.1
20
0.110 µH
27 µH
15
1 µH
10
5
0.01
0.1
10
1
Frequency (MHz)
B
overall
Pick and
place
material
G
0.1
1
10
Frequency (MHz)
100
I
J
F
I
D
E
terminal
0
H
C
F
A
100
Terminal wraparound:
approx 0.010/0,25 both ends
Recommended
Land Pattern
ABCD
maxmaxmax ref E F G H IJ
0.0900.0750.0630.0200.0500.0200.0400.0700.0400.030inches
2,291,911,600,511,270,511,021,781,020,76
mm
Note: Height dimension (C) is before optional solder application. For maximum
height dimension including solder, add 0.006 in / 0,152 mm.
Document 288-2 Revised 10/12/15