Document 264-1 Chip Inductors – 0603LS (1608) •Higher inductance values than other 0603 inductors •Ferrite construction for high current handling • Inductance values: 47 nH – 22 µH; 5% and 2% tolerance Designer’s Kit C347 contains 10 each of all 5% values Typical L vs Frequency Weight 4.8 – 6.2 mg Core material Ceramic/Ferrite Environmental RoHS compliant, halogen free optional Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Ambient temperature –40°C to +85°C with Irms current 100000 Maximum part temperature +100°C (ambient + temp rise) Storage temperature Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Inductance (nH) 10000 Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles 8200 nH 3300 nH Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) 1000 nH 1000 100 10 Temperature Coefficient of Inductance (TCL) +50 to +150 ppm/°C 330 nH Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 100 nH Packaging 2000 per 7″ reel. Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.17 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. 1 10 100 1000 C B overall Frequency (MHz) D F Typical Q vs Frequency A 35 30 E terminal 8200 nH Q factor 25 100 nH G J F I Terminal wraparound: approx 0.008/0,20 both ends Recommended Land Pattern Note: B1 = 0.040 ±0.004 in / 1,016 ±0,102 mm B2 = 0.046 ±0.004 in / 1,169 ±0,102 mm 3300 nH 330 nH 15 I ACD maxBmaxref E F G H IJ 0.071 See 0.0440.0150.0300.0130.0340.0400.0250.025inches note 1,120,380,760,330,861,020,640,64 1,80 mm 1000 nH 20 H Pick and place material 10 Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. 5 0 0.1 1 10 100 Frequency (MHz) Document 264-1 Revised 10/12/15 Document 264-2 Chip Inductors – 0603LS Series Inductance2 Percent SRF min4 DCR max5 Irms6 Part number1 (nH)tolerance Q min3 (MHz) (Ohms) (A) 0603LS-47NX_L_ 0603LS-51NX_L_ 0603LS-72NX_L_ 0603LS-101X_L_ 0603LS-121X_L_ 0603LS-151X_L_ 0603LS-181X_L_ 0603LS-241X_L_ 0603LS-271X_L_ 0603LS-331X_L_ 0603LS-391X_L_ 0603LS-471X_L_ 0603LS-561X_L_ 0603LS-681X_L_ 0603LS-781X_L_ 0603LS-821X_L_ 0603LS-102X_L_ 0603LS-122X_L_ 0603LS-152X_L_ 0603LS-182X_L_ 0603LS-222X_L_ 0603LS-272X_L_ 0603LS-332X_L_ 0603LS-392X_L_ 0603LS-472X_L_ 0603LS-562X_L_ 0603LS-682X_L_ 0603LS-782X_L_ 0603LS-822X_L_ 0603LS-103X_L_ 0603LS-153X_L_ 0603LS-183X_L_ 0603LS-223X_L_ 47 @ 7.9 MHz 51 @ 7.9 MHz 72 @ 7.9 MHz 100 @ 7.9 MHz 120 @ 7.9 MHz 150 @ 7.9 MHz 180 @ 7.9 MHz 240 @ 7.9 MHz 270 @ 7.9 MHz 330 @ 7.9 MHz 390 @ 7.9 MHz 470 @ 7.9 MHz 560 @ 7.9 MHz 680 @ 7.9 MHz 780 @ 7.9 MHz 820 @ 7.9 MHz 1000 @ 7.9 MHz 1200 @ 7.9 MHz 1500 @ 7.9 MHz 1800 @ 7.9 MHz 2200 @ 7.9 MHz 2700 @ 7.9 MHz 3300 @ 7.9 MHz 3900 @ 7.9 MHz 4700 @ 7.9 MHz 5600 @ 7.9 MHz 6800 @ 7.9 MHz 7800 @ 7.9 MHz 8200 @ 7.9 MHz 10,000 @ 2.5 MHz 15,000 @ 2.5 MHz 18,000 @ 2.5 MHz 22,000 @ 2.5 MHz 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 12 @ 7.9 MHz 12 @ 7.9 MHz 12 @ 7.9 MHz 12 @ 7.9 MHz 12 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 12 @ 2.5 MHz 20 @ 2.5 MHz 20 @ 2.5 MHz 22 @ 2.5 MHz 1. When ordering, specify tolerance, termination and packaging codes: 0603LS-822XJLC Tolerance: G=2% J = 5% (Table shows stock tolerances in bold.) Termination:L=RoHS compliant silver-palladium-platinum-glass frit. E=Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:C =7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. 1500 1400 1400 1150 1100 1050 950 800 775 725 620 540 525 260 460 410 190 160 100 80 68 60 42 40 34 32 31 28 26 25 23 22 19 0.075 0.075 0.12 0.13 0.15 0.15 0.15 0.16 0.30 0.46 0.51 0.62 0.44 0.52 0.83 0.69 0.81 0.87 0.96 1.1 1.2 1.5 1.5 1.6 2.1 2.6 3.1 3.5 3.6 4.8 7.1 7.6 8.81 1.40 1.00 1.40 1.40 1.40 1.30 1.30 0.95 0.71 0.56 0.50 0.42 0.55 0.47 0.39 0.40 0.40 0.37 0.35 0.35 0.32 0.28 0.28 0.28 0.26 0.24 0.20 0.20 0.19 0.18 0.17 0.16 0.13 ColorOverall codewidth Black Violet Brown Red Orange Yellow Green Violet Gray White Black Brown Red Orange Yellow Green Blue Violet Gray White Black Brown Red Orange Yellow Green Black Blue Violet Gray White Brown Black B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B2 B1 B1 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 2. Inductance measured at 0.1 Vrms, using Coilcraft SMD-A fixture in Agilent/HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Q measured on Agilent/HP 4395A with Agilent/HP 16193 test fixture. 4. SRF measured using Agilent/HP 8753D network analyzer with Coilcraft SMD‑D test fixture. 5. DCR measured on Cambridge Technology Micro-ohmmeter. 6. Current that causes a 15°C temperature rise from 25°C ambient. Because of their open construction, these parts will not saturate.This information is for reference only and does not represent absolute maximum ratings 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 264-2 Revised 02/18/15