Document 1304-1 Ultra Low Profile Common Mode Choke 0805 • For noise suppression in super high speed signal lines: USB 3.x, HDMI 2.0, HDBaseT™, DisplayPort, DVI, etc.; and in high speed differential signal lines: USB 2.0, IEEE1394, LVDS, etc. • Up to 6.5 GHz differential mode 3 dB cutoff frequency; up to 35 dB common mode noise attenuation in GHz range • Lowest profile 0805 common mode choke – 0.93 mm tall Core material Ferrite Environmental RoHS compliant Terminations Matte tin over nickel over silver-platinum-glass frit. Weight 9.0 – 13.0 mg Ambient temperature –40°C to +125°C with Irms current. Maximum part temperature 140°C Storage temperature Component: –40°C to +155°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 2000/7″ reel; 7500/13″ reel; Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.07 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Part number1 Common mode impedance typ (Ohms) 10 MHz 100 MHz 500 MHz 0805USBN-121MR_ 2 12 57 0805USBN-271MR_ 3 27 125 0805USBN-481MR_ 5 48 231 0805USBN-701MR_ 7 70 342 0805USBN-941MR_10 94 493 0805USBN-132MR_ 13 130 697 0805USBN-162MR_ 17 165 955 0805USBN-222MR_ 24 225 1310 Common modeDCR Inductance2 max3 attenuation typ (dB) Isolation4 Irms5 10 MHz 100 MHz 500 MHz min (nH) (Ohms) (Vrms) (mA) 0.040.5 5.0 0.091.4 10.0 0.133.5 14.7 0.185.3 17.4 0.307.6 21.1 0.5010.0 24.4 0.7812.1 27.3 1.1414.0 30.0 1.When ordering, please specify packaging code: 0805USBN-222MLC Packaging:C=7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape (7500 parts per full reel). 2. Inductance measured at 100 MHz using an Agilent/HP 4286A impedance analyzer and a Coilcraft SMD-A fixture. 3.DCR is specified per winding. 4.Winding to winding isolation (hipot) tested for one minute. 5.Current per winding that causes a 15°C rise from 25°C ambient. 5.Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 14 30 53 77 105 140 182 252 0.087 max 2,2 0.11 0.14 0.22 0.235 0.27 0.32 0.37 0.63 250500 250500 250500 250500 250500 250 500 250 450 250 350 1 2 4 3 0.037 max 0,93 0.004 0,10 0.020 0.040 0,51 1,02 1 0.030 0,76 0.018 0,46 0.036 0,91 2 1 3 4 0.014 0,36 2 0.055 max 1,4 4 3 inches Dimensions are in mm US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Recommended Land Pattern 0.020 0,51 Document 1304-1 Revised 05/11/16 © Coilcraft Inc. 2016 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 1304-2 Ultra Low Profile Common Mode Choke — 0805 Typical Differential Mode Attenuation (Ref: 50 Ohms) 0 1 Attenuation (dB) 2 3 4 -222 -162 -132 -941 -701 -481 -271 -121 5 6 7 8 1 10 100 1000 10,000 Frequency (MHz) Typical Common Mode Attenuation (Ref: 50 Ohms) 0 5 Attenuation (dB) 10 15 20 -222 -162 -132 -941 -701 -481 -271 -121 25 30 35 1 10 100 1000 10,000 Frequency (MHz) Typical Impedance vs Frequency 10000 -222 -162 -132 -941 -701 -481 -271 -121 Impedance (Ohms) 1000 100 10 1 0.1 1 10 100 1000 10,000 Frequency (MHz) US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 1304-2 Revised 05/11/16 © Coilcraft Inc. 2016 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.