B0754-AL

Document 418-1
SMT Power Magnetics
For ON Semiconductor
NCP1216A Controller
Coilcraft’s C0972-AL transformer and B0754-AL inductor
were developed specifically for the ON Semiconductor
NCP1216A PWM Current-Mode Controller.
They are specified in application note AND8161/D along
with Coilcraft’s DS3316P-103 and DS3316P-102 shielded
inductors. Refer to the separate data sheet for additional
information about the DS3316 Series of inductors
The C0972-AL features very low DCR, excellent leakage
inductance and 1500 Vrms isolation from the primary and
auxiliary windings to the secondary.
The B0754-AL is the output inductor and features four
separate windings connected in parallel to minimize power
losses and to limit temperature rise.
To request free evaluation samples, contact Coilcraft or
visit www.coilcraft.com.
C0972-AL Transformer
Input Output Primary Leakage
Part
Output
voltage
Output
current inductance1 inductance2 DCR max
number power (W) range (V) voltage (V) (A rms)
min (mH)
max (µH)
(Ohms)
C0972-AL
60
36 – 75
12
5.0
0.817
1.50
0.056 (pri)
0.031 (sec)
0.480 (aux)
2. Inductance measured between pins 2 and 4 at 10 kHz, 0.1 V, 0 Adc.
3. Leakage inductance measured between pins 2 and 4 at 100 kHz, 0.1 V,
0 Adc with all other pins shorted.
4. Operating temperature range: –40°C to +85°C.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Dot above pin1
0.560 max
14,22
0.004 /0,10
0.035
0,90
0.108
2,74
2
Primary
4
5
Reset
1
Turns ratio
pri : sec pri: reset
1 : 0.91
1 : 1
1.280
max
32,51
0.079
2,00
1.10
27,94
0.043
1,10
1.024
26,00
6
5
10
Recommended
Land Pattern
Secondary
6
10
1.060 max
26,92
1
0.196
4,98
Weight:
28.2 g
Terminations: Tin-silver (96.5/3.5) over tin over nickel over phos bronze
Packaging:
24 per tray
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
10
1
Bottom View
0.196
4,98
Dimensions are in
inches
mm
Document 418-1 Revised 01/23/09
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Document 418-2
SMT Power Magnetics for ON Semiconductor NCP1216A
B0754-AL Inductor
Part
number
B0754-AL
Inductance1
at 0 A
±10% (µH)
100
Dot above pin1
DCR
max2
(Ohms)
0.282
Isat3
(A)
8.0
Irms4
(A)
4.8
1. Inductance measured at 10.0 kHz, 0.1 Vrms.
2. DCR is per winding.
3. Current at which inductance drops 10% (typ) from its value without current.
4. Average current for a 40°C temperature rise above 25°C ambient.
5. Operating temperature range −40°C to +85°C.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.545 max
13,84
0.004 /0,10
0.035
0,90
1.280
max
32,51
0.043
1,10
1.024
26,00
6
5
1.060 max
26,92
1
10
Typical L vs Frequency
Bottom View
0.079
2,00
1000
Inductance (µH)
0.196
4,98
4
3
2
1
Recommended
Land Pattern
100
0.196 10
4,98
0.108
2,74
10
1
1.10
27,94
Dimensions are in
1
0.01
1
0.1
10
Frequency (MHz)
Typical L vs Current
Temperature Rise vs Current
70
Temperature rise (from 25°C)
Inductance (µH)
inches
mm
Windings to be
connected in parallel
on the PC board
Weight:
27.4 g
Terminations: Tin-silver (96.5/3.5) over tin over nickel over phos bronze
Packaging:
24 per tray
1000
100
10
1
10
9
8
7
0.1
10
1
Current (A)
100
60
50
40
30
20
10
0
0
1
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
2
3
4
5
6
7
Current (A)
Document 418-1 Revised 01/23/09
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.