C1590-AL

Document 459
Flyback Transformers
For Texas Instruments
LM5070 PoE Interface – 3 Watt
• Flyback transformers for 3 W PoE applications
• Designed to operate in continuous mode at 250 kHz with an
input of 36 – 72 Vdc
• 1500 Vrms isolation from primary and bias to secondary
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos bronze.
Other terminations available at additional cost.
Weight 2.05 g
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 350 per 13″ reel Plastic tape: 32 mm wide, 0.42 mm thick,
20 mm pocket spacing, 9.16 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
InductanceInductance
Leakage
3
DCR max (Ohms)4 inductance5 Turns ratio6
Part at 0 A2
at
Ipk
Ipk3
1
number ±10% (µH)
min (µH)
pri
bias
sec
max (µH)
pri : secpri : bias(A) Output7
C1590-AL_
310
279
1.02
2.01
0.066
4.75
1 : 0.191 : 0.70 0.3 3.3 V, 0.91 A
C1591-AL_
310
279
1.02
2.01
0.118
4.50
1 : 0.281 : 0.70 0.3 5.0 V, 0.6 A
C1592-AL_
310
279
1.04
2.01
0.700
4.25
1 : 0.701 : 0.70 0.3 12 V, 0.25 A
1. When ordering, please specify packaging code:
C1592-ALD
Packaging:D
=13″ machine-ready reel. EIA-481 embossed plastic
tape (350 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
Dot above pin1
2. Inductance is for the primary, measured at 10 kHz, 0.1 Vrms, 0 Adc.
3.Ipk is peak primary current drawn at minimum input voltage.
4. DCR for the secondary is per winding.
5. Leakage inductance measured between pins 3 and 4 with all other pins
shorted.
6. Turns ratio is with the secondary windings connected in parallel.
7. Output of the secondary is with the windings connected in parallel. Bias
winding output is 12 V, 20 mA.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.355 max
9,02
0.004 /0,10
0.041
1,05
0.520 max
13,21
3
0.339
8,60
1
0.028
0,70
8
Recommended
Land Pattern
0.080
2,03
0.370
9,40
Pri
0.050
1,27
4
2
Sec
7
8
Bias
0.430 max
10,92
4
6
5
0.098
2,50
5
1
0.098
2,50
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
1
Secondary windings to be connected
in parallel on the PC board
Document 459 Revised 10/29/08
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.