Document 733 Flyback Transformer For Linear Technology LT3573 Isolated Flyback Converter • Designed for the LT3573 Isolated Flyback Converter • 1500 Vrms isolation from primary and bias to secondary; 500 Vrms isolation from primary to bias, tested for one minute • The bias winding provides power to the chipset Core material Ferrite Terminations RoHS tin-silver over tin over nickel over phos bronze. Other terminations available at additional cost. Weight 3.9 to 4.1 g Ambient temperature –40°C to +85°C Storage temperature Component: –40°C to +85°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 250 per 13″ reel Plastic tape: 32 mm wide, 0.5 mm thick, 20 mm pocket spacing, 11.2 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf InductanceInductance LeakageInput 2 3 DCR max (mOhms)4inductance Turns ratio6 Ipk3 voltage Part at 0 A at Ipk Output7 number1 ±10% (µH) min (µH) pri sec bias max (µH)5 pri : sec : bias (A) (V) GA3429-BL_24.0 21.6 957.5123 0.566 4 : 1 : 1 2.1 20 – 28 3.3 V, 1.5 A 1. When ordering, please specify packaging code: 3 Pri 4 2 FA267x-AL CCI xxxx GA3429-BLD Packaging:D =13″ machine-ready reel. EIA-481 embossed plastic tape (250 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary, measured at 250 kHz, 0.3 Vrms, 0 Adc. 3.Ipk is peak primary current drawn at minimum input voltage. 4. DCR for the secondary is per winding. 5. Leakage inductance measured between pins 3 and 4 with all secondary pins shorted. 6. Turns ratio is with the secondary windings connected in parallel. 7. Output is with the secondary windings connected in parallel. Bias winding output: 3.3 V, 20 mA . 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 0.433 max 11,00 0.004 /0,10 0.041 1,05 0.413 10,50 8 1 0.024 0,60 0.080 2,03 0.460 11,68 0.050 1,27 0.50 max 12,7 4 5 6 5 Sec Dot above pin1 0.600 max 15,24 Dimensions are in 1 0.098 2,50 Recommended 0.098 2,50 Land Pattern inches mm 7 8 Bias 1 Secondary windings to be connected in parallel on PC board US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 733 Revised 05/04/09 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.