FA2671-AL

Document 560
Flyback Transformers
For Silicon Laboratories
Si3402 PD Controller
• Designed for Power over Ethernet PD controllers for applications up to 10 Watts.
• Operates in continuous conduction mode with 36 – 72 V input
• 1500 Vrms, one minute isolation between primary and secondary
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos bronze.
Other terminations available at additional cost.
Weight 3.8 – 3.9 g
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Maximum part temperature +125°C (ambient + temp rise)
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 200 per 13″ reel Plastic tape: 32 mm wide, 0.5 mm thick,
24 mm pocket spacing, 11.2 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Leakage
InductanceInductance
3
  DCR max (Ohms)4inductance Turns ratio6 Ipk3
Part Power at 0 A2
at Ipk number1
(W)
±10% (µH)
min (µH)
pri sec
max (µH)5
pri : sec
(A)
FA2671-AL_10
FA2672-AL_10
FA2732-AL_10
40.0
40.0
40.0
36.0
36.0
36.0
0.098 0.062
0.098 0.045
0.098 0.156
0.395
0.340
0.370
1 : 0.3
1 : 0.4
1 : 1
1.3
1.3
1.3
Output
3.3 V, 3.0 A
5.0 V, 2.0 A
12.0 V, 0.83 A
1. When ordering, please specify packaging code:
3
5
6
Pri
Sec
2
FA267x-AL
CCI xxxx
FA2672-ALD
Packaging:D
=13″ machine-ready reel. EIA-481 embossed plastic
tape (200 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
2. Inductance is for the primary, measured at 400 kHz, 0.4 Vrms, 0 Adc.
3.Ipk is peak primary current drawn at minimum input voltage.
4. DCR for the secondary is per winding.
5. Leakage inductance measured between pins 2 and 3 with all secondary
pins shorted.
6. Turns ratio is with the secondary windings connected in parallel.
7. Output is with the secondary windings connected in parallel.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.433 max
11,00
0.004 /0,10
0.041
1,05
Dot above pin1
0.600 max
15,24
0.413
10,50
8
1
0.024
0,60
0.080
2,03
0.460
11,68
0.050
1,27
0.50 max
12,7
4
Dimensions are in
5
1
0.098
2,50
Recommended 0.098
2,50
Land Pattern
inches
mm
8
7
Secondary windings to be connected in parallel on PC board
Document 560 Revised 06/18/15