Document 888 Isolation Transformers For Analog Devices ADuM347x Quad-Channel Digital Isolators • Developed to work with Analog Devices ADuM347x quadchannel, digital isolators with integrated PWM controller and transformer driver • Power rating: 2 Watts • Designed to meet UL/CSA/IEC 60950 Basic Insulation with 1.5 mm creepage and clearance. Core material Ferrite Terminations Tin-silver over tin over nickel over phos bronze Isolation 2500 Vrms primary to secondary; 500 Vrms winding to core Weight 0.95 – 0.98 g Ambient temperature –40°C to +125°C Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 600/13″ reel; Plastic tape: 24 mm wide, 0.37 mm thick, 16 mm pocket spacing, 6.1 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf Part number1 Inductance2 min (µH) Turns ratio pri JA4631-BL_ JA4650-BL_ KA4976-AL_ 63.75 63.75 63.75 1:2 1:3 1:5 5V 5V 5V Pri / output voltages output output (pin 8) (pins 6 & 7) +3.3 to +5 V +12 to +15 V +12 to +15 V output (pin 5) 0V No output +6 to +7.5 V 0V 0V –12 to –15 V DCR max (Ohms)3 pri sec 0.095 0.122 0.095 0.190 0.260 1.17 Leakage Volt-time inductance4 product5 max (µH) (V-µsec) 0.460 0.660 0.515 17.6 17.6 17.6 1. When ordering, please specify a packaging code: JA4631-BLD Packaging: D = 13″ machine ready reel. EIA-481 embossed plastic tape (600 per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary, measured from pins 4 – 3 at 1 kHz, 0.1 Vrms. 3. DCR is for each winding of the primary and secondary. 4. Leakage inductance is for the primary windings, measured from pins 1 – 4 with all secondary windings shorted. 5. Based on Bsat of the core at 25°C and the number of turns on winding 4 - 3. 6. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Analog Devices is a trademark of Analog Devices, Inc. Dimensions are in inches mm US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 888 Revised 09/01/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.