MOS6020

Document 287 -1
Shielded Power Inductors – MOS6020
• 6.0 × 7.1 mm footprint; 2.4 mm high shielded inductors
• Custom versions up to 4.7 mH are available.
Designer’s Kit C359 contains 3 of each value
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant matte tin over nickel over phos bronze.
Other terminations available at additional cost.
Weight 0.21 g
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 500 per 7″ reel; 2000 per 13″ reel; Plastic tape: 16 mm wide,
0.3 mm thick, 12 mm pocket spacing, 2.5 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
2 Isat (A)4
Irms (A)5
Inductance2 DCR max SRF typ3
Part number1
±20% (µH)
(Ohms)
(MHz)
10% drop 20% drop 30% drop
20°C rise 40°C rise
MOS6020-222ML_2.2 0.035 110
2.863.26 3.56 3.0 4.1
MOS6020-332ML_3.3 0.046 85
1.902.28 2.46 2.6 3.6
MOS6020-472ML_4.7 0.050 60
1.461.82 1.94 2.3 3.1
MOS6020-682ML_6.8 0.078 55
1.321.56 1.72 1.9 2.7
MOS6020-822ML_8.2 0.085 45
0.941.18 1.30 1.7 2.3
MOS6020-103ML_10
0.092
36
0.79 0.95 1.06
1.6 2.2
MOS6020-153ML_15
0.130
30
0.83 0.95 1.03
1.3 1.8
MOS6020-223ML_22
0.182
22
0.79 0.92 0.97
1.0 1.4
MOS6020-333ML_
33 0.290 20
0.570.670.74 0.801.1
MOS6020-473ML_
47 0.420 16
0.450.560.62 0.500.7
MOS6020-683ML_
68 0.520 15
0.370.450.51 0.450.63
MOS6020-104ML_
100 0.800 13
0.350.400.44 0.400.56
MOS6020-154ML_
150 1.28
10
0.260.300.33 0.350.49
MOS6020-224ML_
220 2.00
8
0.220.260.28 0.300.42
MOS6020-334ML_
330 2.84
7
0.180.220.24 0.250.35
MOS6020-474ML_
470 4.40
5
0.150.170.19 0.220.29
1. When ordering, please specify termination and packaging codes:
MOS6020-104MLC
Termination:L=RoHS compliant matte tin over nickel over phos bronze.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (500 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (2000 parts per
full reel).
2.Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/
HP 4263B LCR meter or equivalent.
3. SRF measured using Agilent/HP 8753D network analyzer.
4. DC current at 25°C that causes the specified inductance drop from its
value without current. Click for temperature derating information.
5. Current that causes the specified temperature rise from 25°C ambient.
This information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 287-1 Revised 09/02/15
Document 287-2
Shielded Power Inductors – MOS6020
Typical L vs Frequency
Typical L vs Current
10000
10000
1000
470 µH
Inductance (µH)
Inductance (µH)
1000
100 µH
100
10 µH
10
2.2 µH
470 µH
100
100 µH
10
10 µH
2.2 µH
1
1
0.1
0.01
1
0.1
10
Frequency (MHz)
0.268
max
6,8
0.1
1
10
Current (A)
0.095
max
2,4
XXX
0.24
max
6,0
0.1
0.24
max
6,0
0.031
typ
0,80
0.169
typ
4,3
0.225
5,71
0.100
2,54
0.063
typ
1,60
0.055
1,39
Dimensions are in
inches
mm
Recommended
Land Pattern
Document 287-2 Revised 09/02/15