PFL2010

Document 775 -1
Shielded Power Inductors – PFL2010
• Only 1 mm high; requires a mere 3.2 mm2 of board space
• Provides the current handling of much larger inductors; up
to 1800 mA
Core material Composite
Core and winding loss See www.coilcraft.com/coreloss
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silver-platinum-glass frit. Other terminations available at additional cost.
Weight 9.5 – 9.8 mg
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 2000/7″ reel; 7500/13″ reel. Plastic tape: 8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.07 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Part number1
5
(mOhms)3
SRF typ4 Isat (mA) typ max
(MHz)
10% drop 20% drop 30% drop
DCR
Inductance2 ±20% (µH)
Irms (mA)6
20°C rise 40°C rise
PFL2010-471ME_
0.47 60
69 6301200 1600
18001500
1900
PFL2010-681ME_0.68
87 95
560
950
1300 1500 1400 1600
PFL2010-102ME_
1.0189
2083478501100
1200640
860
PFL2010-222ME_
2.2423
465129510 680
790480
660
PFL2010-472ME_
4.7618
680 66330 490
570420
560
1. When ordering, please specify termination and packaging codes:
PFL2010-472MEC
Termination:E=RoHS compliant matte tin over nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel).
B
=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel).
2. Inductance tested at 7.9 MHz, 0.1 Vrms using a Coilcraft SMD-F test fixture with an Agilent/HP 4286 impedance analyzer and Coilcraft-provided correlation pieces.
3. DCR measured using a micro-ohmmeter.
4. SRF measured using an Agilent/HP 8753D network analyzer and a Coilcraft SMD-D test fixture.
5. DC current at 25°C that causes the specified inductance drop from its value without current. Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum
ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 775-1 Revised 09/13/15
Document 775-2
PFL2010 Series
Typical L vs Frequency
Typical L vs Current
10
7
10
7
2
2.2 µH
1
1.0 µH
0.7
0.68 µH
0.5
0.4
0.3
4.7 µH
5
4
3
4.7 µH
Inductance (µH)
Inductance (µH)
5
4
3
0.47 µH
2.2 µH
2
1.0 µH
1
0.68 µH
0.7
0.47 µH
0.5
0.4
0.3
0.2
0.2
0.1
0.01
1
0.1
10
Current (A)
0.1
1
10
100
1000
Frequency (MHz)
0.087
max
2,20
0.015
0,38
0.039
max
1,00
Terminal wraparound:
approx 0.01/0,254 both ends
0.012
0,305
0.056
1,42
0.012
0,305
0.050
1,27
0.057 max
1,45
0.070
1,78
0.070
1.78
0.040
1,02
Recommended
Land Pattern
Dimensions are in
inches
mm
Document 775-2 Revised 09/13815