Document 875 -1 Shielded Power Inductors – PFL1609 • Low cost, low profile 0603 size power inductor • Less than 1 mm high; requires less than 2 mm2 of board space • Lower DCR than other parts this size Part number1 (mOhms)3 SRF typ4 Isat (mA)5 typ max (MHz) 10% drop 20% drop 30% drop DCR Inductance2 ±20% (µH) PFL1609-471ME_0.47 83100 650 PFL1609-561ME_0.56 110130 600 PFL1609-681ME_ 0.68145 170520 PFL1609-102ME_ 1.0 200 230445 PFL1609-222ME_ 2.2 410 470130 PFL1609-472ME_4.7 620700 60 1. When ordering, please specify packaging codes: PFL1609-472MEW Packaging:W =7″ machine-ready reel. EIA-481 punched paper tape (2000 parts per full reel). U=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter W instead. 2. Inductance tested at 7.9 MHz, 0.1 Vrms using a Coilcraft SMD-F test fixture with an Agilent/HP 4286A impedance analyzer and Coilcraftprovided correlation pieces. 3. DCR measured using a micro-ohmmeter. 4. SRF measured using an Agilent/HP 8753D network analyzer and a Coilcraft SMD-D test fixture. . DC current at 25°C that causes the specified inductance drop from its value without current. Click for temperature derating information. 6. Current that causes the specified temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 760 710 610 480 300 240 990 1200 920 1100 780900 690760 390470 300 370 Irms (mA)6 20°C rise 40°C rise 1000 1300 1100 1400 11001400 650 850 480 630 380 500 Designer’s Kit C433 contains 20 of each PFL1609 and PFL2010 value Core material Composite Core and winding loss See www.coilcraft.com/coreloss Environmental RoHS compliant, halogen free Terminations RoHS compliant matte tin over nickel over silverplatinum-glass frit. Other terminations available at additional cost. Weight 7.9 – 8.3 mg Ambient temperature –40°C to +85°C with (40°C rise) Irms current. Maximum part temperature +125°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 2000 per 7″ reel Paper tape: 8 mm wide, 1.0 mm thick, 2 mm pocket spacing PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Document 875-1 Revised 09/13/15 Document 875-2 PFL1609 Series L vs Current L vs Frequency 10 10 4.7 µH Inductance (nH) Inductance (nH) 4.7 µH 2.2 µH 1 1.0 µH 0.68 µH 0.56 µH 0.47 µH 0.1 0.01 1.0 µH 1 0.68 µH 0.56 µH 0.47 µH 1 0.1 2.2 µH 10 Current (A) 0.1 1 10 100 1000 Frequency (MHz) 0.071 max 1,80 0.015 0,38 0.037 max 0,95 Terminal wraparound: approx 0.010/0,254 both ends 0.012 0,305 0.036 0,91 0.042 max 1,07 0.012 0,305 0.030 0,76 0.050 1,27 0.040 1,02 0.025 0,64 Recommended Land Pattern Dimensions are in inches mm Document 875-2 Revised 09/13/15