iCE 2016-02 Technology Library

LATTICE
ICE™
Technology Library
Version 2.9
September 08, 2015.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
1
Copyright
Copyright © 2007-2015 Lattice Semiconductor Corporation. All rights reserved. This
document may not, in whole or part, be reproduced, modified, distributed, or publicly
displayed without prior written consent from Lattice Semiconductor Corporation
(“Lattice”).
Trademarks
All Lattice trademarks are as listed at www.latticesemi.com/legal. Synopsys and
Synplify Pro are trademarks of Synopsys, Inc. Aldec and Active-HDL are trademarks of
Aldec, Inc. All other trademarks are the property of their respective owners.
Disclaimers
NO WARRANTIES: THE INFORMATION PROVIDED IN THIS DOCUMENT IS “AS IS”
WITHOUT ANY EXPRESS OR IMPLIED WARRANTY OF ANY KIND INCLUDING
WARRANTIES OF ACCURACY, COMPLETENESS, MERCHANTABILITY,
NONINFRINGEMENT OF INTELLECTUAL PROPERTY, OR FITNESS FOR ANY
PARTICULAR PURPOSE. IN NO EVENT WILL LATTICE OR ITS SUPPLIERS BE
LIABLE FOR ANY DAMAGES WHATSOEVER (WHETHER DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL, INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR
LOSS OF INFORMATION) ARISING OUT OF THE USE OF OR INABILITY TO USE
THE INFORMATION PROVIDED IN THIS DOCUMENT, EVEN IF LATTICE HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME
JURISDICTIONS PROHIBIT THE EXCLUSION OR LIMITATION OF CERTAIN
LIABILITY, SOME OF THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
Lattice may make changes to these materials, specifications, or information, or to the
products described herein, at any time without notice. Lattice makes no commitment to
update this documentation. Lattice reserves the right to discontinue any product or
service without notice and assumes no obligation to correct any errors contained herein
or to advise any user of this document of any correction if such be made. Lattice
recommends its customers obtain the latest version of the relevant information to
establish that the information being relied upon is current and before ordering any
products.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
2
Revision History
Version
2.0
2.1
Changes
Added Version Number to document. Added sections on Default
Signal Values for unconnected ports.
Added PLL primitives
2.2
Corrected SB_CARRY connections to LUT inputs
2.3
Added iCE40 RAM, PLL primitives.
2.4
Added PLL_DS, SB_MIPI_RX_2LANE, SB_TMDS_deserializer
primitives.
Added SB_MAC16 Primitive details.
2.5
2.6
2.7
Added iCE40LM Hard Macro details.
Removed PLL_DS, SB_MIPI, SB_TMDS, SB_MAC16 primitive
details.
Added iCE5LP (iCE40 Ultra) primitive details.
2.8
Removed iCE65 RAM, PLL details.
2.9
Added iCE40UL (iCE40 Ultra Lite) primitive details
ICE Technology Library
Lattice Semiconductor Corporation Confidential
3
Table of Contents
Register Primitives .......................................................................................................... 6
SB_DFF ................................................................................................................... 6
SB_DFFE ................................................................................................................. 8
SB_DFFSR ............................................................................................................ 10
SB_DFFR ............................................................................................................... 12
SB_DFFSS ............................................................................................................ 14
SB_DFFS ............................................................................................................... 16
SB_DFFESR .......................................................................................................... 18
SB_DFFER ............................................................................................................ 20
SB_DFFESS .......................................................................................................... 22
SB_DFFES ............................................................................................................ 24
SB_DFFN ............................................................................................................... 26
SB_DFFNE ............................................................................................................ 28
SB_DFFNSR .......................................................................................................... 30
SB_DFFNR ............................................................................................................ 32
SB_DFFNSS .......................................................................................................... 34
SB_DFFNS ............................................................................................................ 36
SB_DFFNESR ....................................................................................................... 38
SB_DFFNER .......................................................................................................... 40
SB_DFFNESS........................................................................................................ 42
SB_DFFNES .......................................................................................................... 44
Combinational Logic Primitives ..................................................................................... 46
SB_LUT4 ............................................................................................................... 46
SB_CARRY ............................................................................................................ 48
Block RAM Primitives .................................................................................................... 50
iCE40 Block RAM ........................................................................................... 50
SB_RAM256x16..................................................................................................... 51
SB_RAM256x16NR ............................................................................................... 53
SB_RAM256x16NW ............................................................................................... 54
SB_RAM256x16NRNW ......................................................................................... 56
SB_RAM512x8....................................................................................................... 59
SB_RAM512x8NR ................................................................................................. 61
SB_RAM512x8NW ................................................................................................. 62
SB_RAM512x8NRNW ........................................................................................... 64
SB_RAM1024x4..................................................................................................... 67
SB_RAM1024x4NR ............................................................................................... 69
SB_RAM1024x4NW ............................................................................................... 70
SB_RAM1024x4NRNW ......................................................................................... 72
SB_RAM2048x2..................................................................................................... 75
SB_RAM2048x2NR ............................................................................................... 77
SB_RAM2048x2NW ............................................................................................... 78
SB_RAM2048x2NRNW ......................................................................................... 80
ICE Technology Library
Lattice Semiconductor Corporation Confidential
4
SB_RAM40_4K ...................................................................................................... 82
IO Primitives .................................................................................................................. 87
SB_IO .................................................................................................................... 87
Global Buffer Primitives ................................................................................................. 91
SB_GB_IO ............................................................................................................. 91
SB_GB Primitive .................................................................................................... 92
PLL Primitives ............................................................................................................... 93
iCE40 PLL Primitives ...................................................................................... 93
SB_PLL40_CORE.................................................................................................. 93
SB_PLL40_PAD..................................................................................................... 97
SB_PLL40_2_PAD............................................................................................... 101
SB_PLL40_2F_CORE ......................................................................................... 104
SB_PLL40_2F_PAD ............................................................................................ 108
Hard Macro Primitives ................................................................................................. 112
iCE40LM Hard Macros ................................................................................. 112
SB_HSOSC (For HSSG) ...................................................................................... 112
SB_LSOSC (For LPSG) ....................................................................................... 113
SB_I2C ................................................................................................................. 113
SB_SPI ................................................................................................................ 116
iCE5LP (iCE40 Ultra) Hard Macros .............................................................. 120
SB_HFOSC .......................................................................................................... 120
SB_LFOSC .......................................................................................................... 121
SB_LED_DRV_CUR ............................................................................................ 122
SB_RGB_DRV ..................................................................................................... 123
SB_IR_DRV ......................................................................................................... 124
SB_RGB_IP ......................................................................................................... 126
SB_IO_OD ........................................................................................................... 127
SB_I2C ................................................................................................................. 129
SB_SPI ................................................................................................................ 130
SB_MAC16 .......................................................................................................... 131
iCE40UL (iCE40 Ultra Lite) Hard Macros ..................................................... 144
SB_HFOSC .......................................................................................................... 144
SB_LFOSC .......................................................................................................... 145
SB_RGBA_DRV................................................................................................... 146
SB_IR400_DRV ................................................................................................... 148
SB_BARCODE_DRV ........................................................................................... 149
SB_IR500_DRV ................................................................................................... 150
SB_LEDDA_IP ..................................................................................................... 152
SB_IR_IP ............................................................................................................. 153
SB_IO_OD ........................................................................................................... 156
SB _I2C_FIFO...................................................................................................... 158
Device Configuration Primitives .................................................................................. 161
SB_WARMBOOT ................................................................................................. 161
ICE Technology Library
Lattice Semiconductor Corporation Confidential
5
Register Primitives
SB_DFF
D Flip-Flop
Data: D is loaded into the flip-flop during a rising clock edge transition.
D SB_DFF Q
C
Inputs
D
Power on
State
0
1
X
Output
C
Q
Key
X
0
1
0
1
0
X
?
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL use
This register is inferred during synthesis and can also be explicitly instantiated.
Verilog Instantiation
// SB_DFF - D Flip-Flop.
SB_DFF SB_DFF_inst (
.Q(Q),
.C(C),
.D(D),
);
// Registered Output
// Clock
// Data
// End of SB_DFF instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
6
VHDL Instantiation
-- SB_DFF - D Flip-Flop.
SB_DFF_inst: SB_DFF
port map (
Q => Q,
C => C,
D => D,
);
-- Registered Output
-- Clock
-- Data
-- End of SB_DFF instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
7
SB_DFFE
D Flip-Flop with Clock Enable
Data D is loaded into the flip-flop when Clock Enable E is high, during a rising clock edge transition.
SB_DFFE
D
E
Q
C
Inputs
Output
E
D
C
Q
0
1
1
Power on
State
X
0
1
X
X
Previous Q
X
0
1
0
Key
1
0
X
?
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input E: Logic ‘1’
Note that explicitly connecting a logic ‘1’ value to port E will result in a non-optimal implementation, since
an extra LUT will be used to generate the logic ‘1’. It is recommended that the user leave the port E
unconnected, or use the corresponding flip-flop without Enable functionality i.e. the DFF primitive.
Verilog Instantiation
// SB_DFFE - D Flip-Flop with Clock Enable.
SB_DFFE
SB_DFFE_inst (
.Q(Q),
.C(C),
.D(D),
.E(E),
);
// End of SB_DFFE instantiation
//
//
//
//
Registered Output
Clock
Data
Clock Enable
ICE Technology Library
Lattice Semiconductor Corporation Confidential
8
VHDL Instantiation
-- SB_DFFE - D Flip-Flop with Clock Enable.
SB_DFFE_inst: SB_DFFE
port map (
Q => Q,
C => C,
D => D,
E => E,
);
-----
Registered Output
Clock
Data
Clock Enable
-- End of SB_DFFE instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
9
SB_DFFSR
D Flip-Flop with Synchronous Reset
Data: D is loaded into the flip-flop when Reset R is low during a rising clock edge transition.
Reset: R input is active high, overrides all other inputs and resets the Q output during a rising clock edge.
D
Q
SB_DFFSR
C
Inputs
R
D
1
X
0
0
Power on
State
X
X
0
1
X
R
Output
C
0
X
Q
0
No Change
0
1
0
Key
1
0
X
?
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Verilog Instantiation
// SB_DFFSR - D Flip-Flop, Reset is synchronous with the rising clock edge
SB_DFFSR SB_DFFSR_inst (
.Q(Q),
//
.C(C),
//
.D(D),
//
.R(R)
//
);
Registered Output
Clock
Data
Synchronous Reset
// End of SB_DFFSR instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
10
VHDL Instantiation
-- SB_DFFSR - D Flip-Flop, Reset is synchronous with the rising clock edge
SB_DFFSR_inst : SB_DFFSR
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
D => D,
-- Data
R => R
-- Synchronous Reset
);
-- End of SB_DFFSR instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
11
SB_DFFR
D Flip-Flop with Asynchronous Reset
Data: D is loaded into the flip-flop when R is low during a rising clock edge transition.
Reset: R input is active high, overrides all other inputs and asynchronously resets the Q output.
D
SB_DFFR
Q
C
R
Inputs
Output
R
D
C
Q
Key
1
0
0
Power on
State
X
0
1
X
X
0
0
1
0
1
0
X
?
X
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Verilog Instantiation
// SB_DFFR - D Flip-Flop, Reset is asynchronous to the clock.
SB_DFFR
SB_DFFR_inst (
.Q(Q),
//
.C(C),
//
.D(D),
//
.R(R)
//
);
Registered Output
Clock
Data
Asynchronous Reset
ICE Technology Library
Lattice Semiconductor Corporation Confidential
12
// End of SB_DFFR instantiation
VHDL Instantiation
-- SB_DFFR - D Flip-Flop, Reset is asynchronous to the clock.
SB_DFFR_inst: SB_DFFR
port map (
Q => Q,
C => C,
D => D,
R => R
);
-- Registered Output
-- Clock
-- Data
-- Asynchronous Reset
-- End of SB_DFFR instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
13
SB_DFFSS
D Flip-Flop with Synchronous Set
Data: D is loaded into the flip-flop when the Synchronous Set S is low during a rising clock edge
transition.
Set: S input is active high, overrides all other inputs and synchronously sets the Q output.
SB_DFFSS
D
Q
C
Inputs
S
D
1
0
0
Power on
State
X
0
1
X
S
Output
C
Q
Key
X
1
0
1
0
1
0
X
?
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input S: Logic ‘0’
Verilog Instantiation
// SB_DFFSS - D Flip-Flop, Set is synchronous with the rising clock edge,
SB_DFFSS SB_DFFSS_inst (
.Q(Q),
//
.C(C),
//
.D(D),
//
.S(S)
//
);
Registered Output
Clock
Data
Synchronous Set
// End of SB_DFFSS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
14
VHDL Instantiation
-- SB_DFFSS - D Flip-Flop, Set is synchronous with the rising clock edge
SB_DFFSS_inst SB_DFFSS
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
D => D,
-- Data
S => S
-- Synchronous Set
);
-- End of SB_DFFSS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
15
SB_DFFS
D Flip-Flop with Asynchronous Set
Data: D is loaded into the flip-flop when S is low during a rising clock edge transition.
Set: S input is active high, and it overrides all other inputs and asynchronously sets the Q output.
SB_DFFS
D
Q
C
Inputs
S
Output
S
D
C
Q
Key
1
0
0
Power on
State
X
0
1
X
X
1
0
1
0
1
0
X
?
X
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input S: Logic ‘0’
Verilog Instantiation
// SB_DFFS - D Flip-Flop, Set is asynchronous to the rising clock edge
SB_DFFS
SB_DFFS_inst (
.Q(Q),
//
.C(C),
//
.D(D),
//
.S(S)
//
);
Registered Output
Clock
Data
Asynchronous Set
// End of SB_DFFS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
16
VHDL Instantiation
-- SB_DFFS - D Flip-Flop, Set is asynchronous to the rising clock edge
SB_DFFS_inst: SB_DFFS
port map (
Q => Q,
C => C,
D => D,
S => S
);
-- Registered Output
-- Clock
-- Data
-- Asynchronous Set
-- End of SB_DFFS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
17
SB_DFFESR
D Flip-Flop with Clock Enable and Synchronous Reset
Data: D is loaded into the flip-flop when Reset R is low and Clock Enable E is high during a rising clock
edge transition.
Reset: R, when asserted with Clock Enable E high, synchronously resets the Q output during a rising
clock edge.
SB_DFFESR
D
Q
E
C
R
Inputs
Output
R
E
D
1
X
0
0
Power on
State
1
0
1
1
X
X
X
0
1
X
C
Q
0
X
Previous Q
X
0
1
0
Key
1
0
X
?
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Input E: Logic ‘1’
Note that explicitly connecting a Logic ‘1’ value to port E will result in a non-optimal implementation, since
an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep the FF always
enabled, it is recommended that either port E be left unconnected, or the corresponding FF without a
Clock Enable port be used.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
18
Verilog Instantiation
// SB_DFFESR - D Flip-Flop, Reset is synchronous with rising clock edge
// Clock Enable.
SB_DFFESR SB_DFFESR_inst (
.Q(Q),
.C(C),
.E(E),
.D(D),
.R(R)
);
//
//
//
//
//
Registered Output
Clock
Clock Enable
Data
Synchronous Reset
// End of SB_DFFESR instantiation
VHDL Instantiation
-- SB_DFFESR - D Flip-Flop, Reset is synchronous with rising clock edge
-- Clock Enable.
SB_DFFESR_inst: SB_DFFESR
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
E => E,
-- Clock Enable
D => D,
-- Data
R => R
-- Synchronous Reset
);
-- End of SB_DFFESR instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
19
SB_DFFER
D Flip-Flop with Clock Enable and Asynchronous Reset
Data: D is loaded into the flip-flop when Reset R is low and Clock Enable E is high during a rising clock
edge transition.
Reset: R input is active high, overrides all other inputs and asynchronously resets the Q output.
D SB_DFFERQ
E
C
R
Inputs
Output
R
E
D
C
Q
1
0
0
0
Power on
State
X
0
1
1
X
X
X
0
1
X
X
X
0
Previous Q
X
0
1
0
Key
1
0
X
?
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Input E: Logic ‘1’
Note that explicitly connecting a Logic ‘1’ value to port E will result in a non-optimal implementation, since
an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep the FF always
enabled, it is recommended that either port E be left unconnected, or the corresponding FF primitive
without a Clock Enable port be used.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
20
Verilog Instantiation
// SB_DFFER - D Flip-Flop, Reset is asynchronously on rising clock edge with Clock Enable.
SB_DFFER SB_DFFER_inst (
.Q(Q),
//
.C(C),
//
.E(E),
//
.D(D),
//
.R(R)
//
);
Registered Output
Clock
Clock Enable
Data
Asynchronously Reset
// End of SB_DFFER instantiation
VHDL Instantiation
-- SB_DFFER - D Flip-Flop, Reset is asynchronously
-- on rising clock edge with Clock Enable.
SB_DFFER_inst : SB_DFFER
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
E => E,
-- Clock Enable
D => D,
-- Data
R => R
-- Asynchronously Reset
);
-- End of SB_DFFER instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
21
SB_DFFESS
D Flip-Flop with Clock Enable and Synchronous Set
Data: D is loaded into the flip-flop when S is low and E is high during a rising clock edge transition.
Set: Asserting S when Clock Enable E is high, synchronously sets the Q output.
D
Q
SB_DFFESS
E
C
S
Inputs
Output
S
E
D
1
0
0
0
Power on
State
1
0
1
1
X
X
X
0
1
X
C
Q
1
X
Previous Q
X
0
1
0
Key
1
0
X
?
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Input S: Logic ‘0’
Verilog Instantiation
// SB_DFFESS - D Flip-Flop, Set is synchronous with rising clock edge and Clock Enable.
SB_DFFESS SB_DFFESS_inst (
.Q(Q),
// Registered Output
.C(C),
// Clock
.E(E),
// Clock Enable
.D(D),
// Data
.S(S)
// Synchronously Set
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
22
// End of SB_DFFESS instantiation
VHDL Instantiation
-- SB_DFFESS - D Flip-Flop, Set is synchronous with rising clock edge and Clock Enable.
SB_DFFESS_inst : SB_DFFESS
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
E => E,
-- Clock Enable
D => D,
-- Data
S => S
-- Synchronously Set
);
-- End of SB_DFFESS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
23
SB_DFFES
D Flip-Flop with Clock Enable and Asynchronous Set
Data: D is loaded into the flip-flop when S is low and E is high during a rising clock edge transition.
Set: S input is active high, overrides all other inputs and asynchronously sets the Q output.
D SB_DFFES Q
E
C
S
Inputs
Output
S
E
D
CLK
Q
1
0
0
0
Power on
State
X
0
1
1
X
X
X
0
1
X
X
X
1
Previous Q
X
0
1
0
Key
1
0
X
?
Rising Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input S: Logic ‘0’
Input E: Logic ‘1’
Verilog Instantiation
// SB_DFFES - D Flip-Flop, Set is asynchronous on rising clock edge with Clock Enable.
SB_DFFES
SB_DFFES_inst (
.Q(Q),
//
.C(C),
//
.E(E),
//
.D(D),
//
.S(S)
//
);
Registered Output
Clock
Clock Enable
Data
Asynchronously Set
ICE Technology Library
Lattice Semiconductor Corporation Confidential
24
// End of SB_DFFES instantiation
VHDL Instantiation
-- SB_DFFES - D Flip-Flop, Set is asynchronous on rising clock edge with Clock Enable.
SB_DFFES_inst : SB_DFFES
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
E => E,
-- Clock Enable
D => D,
-- Data
S => S
-- Asynchronously Set
);
-- End of SB_DFFES instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
25
SB_DFFN
D Flip-Flop – Negative Edge Clock
Data: D is loaded into the flip-flop during the falling clock edge transition.
SB_DFFN
D
Q
C
Inputs
D
Power on
State
0
1
X
Output
C
Q
Key
X
0
1
0
1
0
X
?
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Verilog Instantiation
// SB_DFFN - D Flip-Flop – Negative Edge Clock.
SB_DFFN SB_DFFN_inst (
.Q(Q),
.C(C),
.D(D),
);
// Registered Output
// Clock
// Data
// End of SB_DFFN instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
26
VHDL Instantiation
-- SB_DFFN - D Flip-Flop – Negative Edge Clock.
SB_DFFN_inst : SB_DFFN
port map (
Q => Q,
C => C,
D => D,
);
-- Registered Output
-- Clock
-- Data
-- End of SB_DFFN instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
27
SB_DFFNE
D Flip-Flop – Negative Edge Clock and Clock Enable
Data: D is loaded into the flip-flop when E is high, during the falling clock edge transition.
D
E
Q
SB_DFFNE
C
Inputs
Output
E
D
C
Q
0
1
1
Power on
State
X
0
1
X
X
0
0
1
0
X
Key
1
0
X
?
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input E: Logic ‘1’
Note that explicitly connecting a Logic ‘1’ value to port E will result in a non-optimal implementation, since
an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep the FF always
enabled, it is recommended that either port E be left unconnected, or the corresponding FF without a
Clock Enable port be used.
Verilog Instantiation
// SB_DFFNE - D Flip-Flop – Negative Edge Clock and Clock Enable.
SB_DFFNE SB_DFFNE_inst
.Q(Q),
.C(C),
.D(D),
.E(E),
);
(
//
//
//
//
Registered Output
Clock
Data
Clock Enable
ICE Technology Library
Lattice Semiconductor Corporation Confidential
28
// End of SB_DFFNE instantiation
VHDL Instantiation
-- SB_DFFNE - D Flip-Flop – Negative Edge Clock and Clock Enable.
SB_DFFNE_inst : SB_DFFNE
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
D => D,
-- Data
E => E,
-- Clock Enable
);
-- End of SB_DFFNE instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
29
SB_DFFNSR
D Flip-Flop – Negative Edge Clock with Synchronous Reset
Data: D is loaded into the flip-flop when R is low during the falling clock edge transition.
Reset: R input is active high, overrides all other inputs and resets the Q output during the falling clock
edge transition.
D
Q
SB_DFFNSR
E
C
Inputs
R
Output
R
D
1
X
0
0
Power on
State
X
X
0
1
X
C
Q
X
0
No Change
0
1
0
Key
1
0
X
?
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Verilog Instantiation
// SB_DFFNSR - D Flip-Flop – Negative Edge Clock, Reset is synchronous with the falling clock edge
SB_DFFNSR
SB_DFFNSR_inst
.Q(Q),
//
.C(C),
//
.D(D),
//
.R(R)
//
);
(
Registered Output
Clock
Data
Synchronous Reset
ICE Technology Library
Lattice Semiconductor Corporation Confidential
30
// End of SB_DFFNSR instantiation
VHDL Instantiation
-- SB_DFFNSR - D Flip-Flop – Negative Edge Clock, Reset is synchronous with the falling clock edge
SB_DFFNSR_inst: SB_DFFNSR
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
D => D,
-- Data
R => R
-- Synchronous Reset
);
-- End of SB_DFFNSR instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
31
SB_DFFNR
D Flip-Flop – Negative Edge Clock with Asynchronous Reset
Data: D is loaded into the flip-flop when R is low during the falling clock edge transition.
Reset: R input is active high, overrides all other inputs and asynchronously resets the Q output.
D
Q
SB_DFFNR
C
R
Inputs
Output
R
D
CLK
Q
Key
1
0
0
Power on
State
X
0
1
X
X
0
0
1
0
1
0
X
?
X
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Verilog Instantiation
// SB_DFFNR - D Flip-Flop – Negative Edge Clock, Reset is asynchronous to the clock.
SB_DFFNR
SB_DFFNR_inst (
.Q(Q),
//
.C(C),
//
.D(D),
//
.R(R)
//
);
Registered Output
Clock
Data
Asynchronously Reset
// End of SB_DFFNR instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
32
VHDL Instantiation
-- SB_DFFNR - D Flip-Flop – Negative Edge Clock, Reset is asynchronous to the clock.
SB_DFFNR_inst : SB_DFFNR
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
D => D,
-- Data
R => R
-- Asynchronously Reset
);
-- End of SB_DFFNR instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
33
SB_DFFNSS
D Flip-Flop – Negative Edge Clock with Synchronous Set
Data: D is loaded into the flip-flop when S is low during the falling clock edge transition.
Set: S input is active high, overrides all other inputs and synchronously sets the Q output.
D
Q
SB_DFFNSS
C
Inputs
S
D
1
0
0
Power on
State
X
0
1
X
S
Output
C
Q
Key
X
1
0
1
0
1
0
X
?
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input S: Logic ‘0’
Verilog Instantiation
// SB_DFFNSS - D Flip-Flop – Negative Edge Clock, Set is synchronous with the falling clock edge,
SB_DFFNSS SB_DFFNSS_inst (
.Q(Q),
// Registered Output
.C(C),
// Clock
.D(D),
// Data
.S(S)
// Synchronous Set
);
// End of SB_DFFNSS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
34
VHDL Instantiation
-- SB_DFFNSS - D Flip-Flop – Negative Edge Clock, Set is synchronous with the falling clock edge,
SB_DFFNSS_inst : SB_DFFNSS
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
D => D,
-- Data
S => S
-- Synchronous Set
);
-- End of SB_DFFNSS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
35
SB_DFFNS
D Flip-Flop – Negative Edge Clock with Asynchronous Set
Data: D is loaded into the flip-flop when S is low during the falling clock edge transition.
Set: S input is active high, overrides all other inputs and asynchronously sets the Q output.
D
Q
SB_DFFNS
C
S
Inputs
Output
S
D
C
Q
Key
1
0
0
Power on
State
X
0
1
X
X
1
0
1
0
1
0
X
?
X
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input S: Logic ‘0’
Verilog Instantiation
// SB_DFFNS - D Flip-Flop – Negative Edge Clock, Set is asynchronous to the falling clock edge,
SB_DFFNS
SB_DFFNS_inst (
.Q(Q),
//
.C(C),
//
.D(D),
//
.S(S)
//
);
Registered Output
Clock
Data
Asynchronous Set
// End of SB_DFFNS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
36
VHDL Instantiation
-- SB_DFFNS - D Flip-Flop – Negative Edge Clock, Set is asynchronous to the falling clock edge
SB_DFFNS_inst : SB_DFFNS
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
D => D,
-- Data
S => S
-- Asynchronous Set
);
-- End of SB_DFFNS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
37
SB_DFFNESR
D Flip-Flop – Negative Edge Clock, Enable and Synchronous Reset
Data: D is loaded into the flip-flop when R is low and E is high during the falling clock edge transition.
Reset: Asserting R when the Clock Enable E is high, synchronously resets the Q output during the falling
clock edge.
SB_DFFNESR
D
Q
E
C
R
Inputs
Output
R
E
D
1
X
0
0
Power on
State
1
0
1
1
X
X
X
0
1
X
C
Q
X
Previous Q
X
0
1
0
Key
0
1
0
X
?
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Input E: Logic ‘1’
Note that explicitly connecting a Logic ‘1’ value to port E will result in a non-optimal implementation, since
an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep the FF always
enabled, it is recommended that either port E be left unconnected, or the corresponding FF without a
Clock Enable port be used.
Verilog Instantiation
// SB_DFFNESR - D Flip-Flop – Negative Edge Clock, Reset is synchronous with falling clock edge Clock
Enable.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
38
SB_DFFNESR
SB_DFFNESR_inst (
.Q(Q),
// Registered Output
.C(C),
// Clock
.E(E),
// Clock Enable
.D(D),
// Data
.R(R)
// Synchronous Reset
);
// End of SB_DFFNESR instantiation
VHDL Instantiation
-- SB_DFFNESR - D Flip-Flop – Negative Edge Clock, Reset is synchronous with falling clock edge Clock
Enable.
SB_DFFNESR_inst :
port map (
Q => Q,
C => C,
E => E,
D => D,
R => R
);
SB_DFFNESR
-- Registered Output
-- Clock
-- Clock Enable
-- Data
-- Synchronous Reset
-- End of SB_DFFNESR instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
39
SB_DFFNER
D Flip-Flop – Negative Edge Clock, Enable and Asynchronous Reset
Data: D is loaded into the flip-flop when R is low and E is high during the falling clock edge transition.
Reset: R input is active high, and it overrides all other inputs and asynchronously resets the Q output.
SB_DFFNER
D
Q
E
C
R
Inputs
Output
R
E
D
C
Q
1
0
0
0
Power on
State
X
0
1
1
X
X
X
0
1
X
X
X
0
Previous Q
X
0
1
0
Key
1
0
X
?
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input R: Logic ‘0’
Input E: Logic ‘1’
Note that explicitly connecting a Logic ‘1’ value to port E will result in a non-optimal implementation, since
an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep the FF always
enabled, it is recommended that either port E be left unconnected, or the corresponding FF without a
Clock Enable port be used.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
40
Verilog Instantiation
// SB_DFFNER - D Flip-Flop – Negative Edge Clock, Reset is asynchronously
// on falling clock edge and Clock Enable.
SB_DFFNER
SB_DFFNER_inst
.Q(Q),
//
.C(C),
//
.E(E),
//
.D(D),
//
.R(R)
//
);
(
Registered Output
Clock
Clock Enable
Data
Asynchronously Reset
// End of SB_DFFNER instantiation
VHDL Instantiation
-- SB_DFFNER - D Flip-Flop – Negative Edge Clock, Reset is asynchronously
-- on falling clock edge and Clock Enable.
SB_DFFNER_inst:
port map (
Q => Q,
C => C,
E => E,
D => D,
R => R
);
SB_DFFNER
-- Registered Output
-- Clock
-- Clock Enable
-- Data
-- Asynchronously Reset
-- End of SB_DFFNER instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
41
SB_DFFNESS
D Flip-Flop – Negative Edge Clock, Enable and Synchronous Set
Data: D is loaded into the flip-flop when S is low and E is high during the falling clock edge transition.
Set: S and E inputs high, synchronously sets the Q output on the falling clock edge transition.
SB_DFFNESS
D
Q
E
C
S
Inputs
Output
S
E
D
1
X
0
0
Power on
State
1
0
1
1
X
X
X
0
1
X
C
Q
1
X
Previous Q
X
0
1
0
Key
1
0
X
?
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input S: Logic ‘0’
Input E: Logic ‘1’
Note that explicitly connecting a Logic ‘1’ value to port E will result in a non-optimal implementation, since
an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep the FF always
enabled, it is recommended that either port E be left unconnected, or the corresponding FF without a
Clock Enable port be used.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
42
Verilog Instantiation
// SB_DFFNESS - D Flip-Flop – Negative Edge Clock, Set is synchronous with falling clock edge,
// and Clock Enable.
SB_DFFNESS
SB_DFFNESS_inst (
.Q(Q),
// Registered Output
.C(C),
// Clock
.E(E),
// Clock Enable
.D(D),
// Data
.S(S)
// Synchronously Set
);
// End of SB_DFFNESS instantiation
VHDL Instantiation
-- SB_DFFNESS - D Flip-Flop – Negative Edge Clock, Set is synchronous with falling clock edge,
-- and Clock Enable.
SB_DFFNESS_inst : SB_DFFNESS
port map (
Q => Q,
-- Registered Output
C => C,
-- Clock
E => E,
-- Clock Enable
D => D,
-- Data
S => S
-- Synchronously Set
);
-- End of SB_DFFNESS instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
43
SB_DFFNES
D Flip-Flop – Negative Edge Clock, Enable and Asynchronous Set
Data: D is loaded into the flip-flop when S is low and E is high during the falling clock edge transition.
Set: S input is active high, and it overrides all other inputs and asynchronously sets the Q output.
SB_DFFNES
D
Q
E
C
S
Inputs
Output
S
E
D
CLK
Q
1
0
0
0
Power on
State
X
0
1
1
X
X
X
0
1
X
X
X
1
Previous Q
X
0
1
0
Key
1
0
X
?
Falling Edge
High logic level
Low logic level
Don’t care
Unknown
HDL Usage
This register is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns the following signal values to unconnected input ports:
Input D: Logic ‘0’
Input C: Logic ‘0’
Input S: Logic ‘0’
Input E: Logic ‘1’
Note that explicitly connecting a Logic ‘1’ value to port E will result in a non-optimal implementation, since
an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep the FF always
enabled, it is recommended that either port E be left unconnected, or the corresponding FF without a
Clock Enable port be used.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
44
Verilog Instantiation
// SB_DFFNES - D Flip-Flop – Negative Edge Clock, Set is asynchronous on falling clock edge with clock
// Enable.
SB_DFFNES
SB_DFFNES_inst
.Q(Q),
//
.C(C),
//
.E(E),
//
.D(D),
//
.S(S)
//
);
(
Registered Output
Clock
Clock Enable
Data
Asynchronously Set
// End of SB_DFFNES instantiation
VHDL Instantiation
-- SB_DFFNES - D Flip-Flop – Negative Edge Clock, Set is asynchronous
-- on falling clock edge and Clock Enable.
SB_DFFNES_inst:
port map (
Q => Q,
C => C,
E => E,
D => D,
S => S
);
SB_DFFNES
-- Registered Output
-- Clock
-- Clock Enable
-- Data
-- Asynchronously Set
-- End of SB_DFFNES instantiation
ICE Technology Library
Lattice Semiconductor Corporation Confidential
45
Combinational Logic Primitives
SB_LUT4
The LUT unit is a simple ROM 4 input look-up function table.
I0
I1
I2
I3
O
4 input
LUT
Initialization values
LUT state initialization parameter LUT_INIT = 16'hxxxx;
Inputs
Output
I3
I2
I1
I0
O
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
LUT_INIT[0]
LUT_INIT[1]
LUT_INIT[2]
LUT_INIT[3]
LUT_INIT[4]
LUT_INIT[5]
LUT_INIT[6]
LUT_INIT[7]
LUT_INIT[8]
LUT_INIT[9]
LUT_INIT[10]
LUT_INIT[11]
LUT_INIT[12]
LUT_INIT[13]
LUT_INIT[14]
LUT_INIT[15]
HDL Usage
This primitive is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns logic value ‘0’ to unconnected input ports.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
46
Verilog Instantiation
// SB_LUT4 : 4-input Look-Up Table
SB_LUT4
SB_LUT4_inst (
.O (O),
// output
.I0 (I0),
// data input 0
.I1 (I1),
// data input 1
.I2 (I2),
// data input 2
.I3 (I3)
// data input 3
);
defparam SB_LUT4_inst.LUT_INIT=16'hxxxx;
//LUT state initialization parameter, 16 bits.
//End of SB_LUT4 instantiation
VHDL Instantiation
-- SB_LUT4 : 4-input Look-Up Table
SB_LUT4_inst: SB_LUT4
generic map(
LUT_INIT => X"0001"
)
port map (
I0 => I0,
I1 => I1,
I2 => I2,
I3 => I3,
O => O
);
-- LUT state initialization parameter, 16 bits
ICE Technology Library
Lattice Semiconductor Corporation Confidential
47
SB_CARRY
Carry Logic
The dedicated Carry Logic within each Logic Cell primarily accelerates and improves the efficiency of
arithmetic logic such as adders, accumulators, subtracters, incrementers, decrementers, counters, ALUs,
and comparators. The Carry Logic also supports a limited number of wide combinational logic functions.
The figure below illustrates the Carry Logic structure within a Logic Cell. The Carry Logic shares inputs
with the associated Look-Up Table (LUT). The I1 and I2 inputs of the LUT directly feed the Carry Logic..
The carry input from the previous adjacent Logic Cell optionally provides an alternate input to the LUT4
function, supplanting the I3 input.
Carry Logic Structure within a Logic Cell
Inputs
Output
I0
I1
CI
CO
0
0
X
X
1
1
0
X
1
0
X
1
X
0
1
0
1
X
0
0
1
0
1
1
HDL Usage
This primitive is inferred during synthesis and can also be explicitly instantiated.
Default Signal Values
The iCEcube2 software assigns logic value ‘0’ to unconnected input ports.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
48
Verilog Instantiation
SB_CARRY my_carry_inst (
.CO(CO),
.I0(I0),
.I1(I1),
.CI(CI));
VHDL Instantiation
my_carry_inst : SB_CARRY
port map (
CO => CO,
CI => CI,
I0 => I0,
I1 => I1
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
49
Block RAM Primitives
The iCE architecture supports dual ported synchronous RAM, with 4096 bits, and a fixed 16 bit datawidth. The block is arranged as 256 x 16 bit words. The RAM block may be configured to be used as a
RAM with data between 1-16 bits.
iCE40 Block RAM
Each iCE40 device includes multiple high-speed synchronous RAM blocks, each 4Kbit in size. The RAM
block has separate write and read ports, each with independent control signals. Each RAM block can be
configured into a RAM block of size 256x16, 512x8, 1024x4 or 2048x2. The data contents of the RAM
block are optionally pre-loaded during ICE device configuration.
The following table lists the supported dual port synchronous RAM configurations, each of 4Kbits in size.
The RAM blocks can be directly instantiated in the top module and taken through iCube2 flow.
Block RAM
Configuration
SB_RAM256x16
SB_RAM256x16NR
SB_RAM256x16NW
SB_RAM256x16NRNW
SB_RAM512x8
SB_RAM512x8NR
SB_RAM512x8NW
SB_RAM512x8NRNW
Block
RAM
Size
WADDR
Port Size
(Bits)
WDATA
Port
Size
(Bits)
RADDR
Port
Size
(Bits)
RDATA
Port
Size
(Bits)
MASK Port
Size (Bits)
256x16
(4K)
8 [7:0]
16 [15:0]
8 [7:0]
16
[15:0]
16 [15:0]
512x8
(4K)
9 [8:0]
8 [7:0]
8 [8:0]
8 [7:0]
No Mask Port
SB_RAM1024x4
SB_RAM1024x4NR
SB_RAM1024x4NW
SB_RAM1024x4NRNW
1024x4
(4K)
10 [9:0]
4 [3:0]
10 [9:0]
4 [3:0]
No Mask Port
SB_RAM2048x2
SB_RAM2048x2NR
SB_RAM2048x2NW
SB_RAM2048x2NRNW
2048x2
(4K)
11 [10:0]
2 [1:0]
10 [9:0]
2 [1:0]
No Mask Port
The Lattice Technologies convention for the iCE40 RAM primitives with negedge Read or Write clock is
that the base primitive name is post fixed with N and R or W according to the clock that is affected, as
displayed in the table below for 256x16 RAM block configuration.
RAM Primitive Name
SB_RAM256x16
SB_RAM4256x16NR
SB_RAM256x16NW
SB_RAM256x16NRNW
Description
Posedge Read clock, Posedge Write clock
Negedge Read clock, Posedge Write clock
Posedge Read clock, Negedge Write clock
Negedge Read clock, Negedge Write clock
ICE Technology Library
Lattice Semiconductor Corporation Confidential
50
SB_RAM256x16
The following modules are the complete list of SB_RAM256x16 based primitives
SB_RAM256x16
SB_RAM256x16
//Posedge clock RCLK WCLK
(RDATA, RCLK, RCLKE, RE, RADDR, WCLK, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM256x16
ram256x16_inst (
.RDATA(RDATA_c[15:0]),
.RADDR(RADDR_c[7:0]),
.RCLK(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[7:0]),
.WCLK(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[15:0]),
.WE(WE_c),
.MASK(MASK_c[15:0])
);
defparam ram256x16_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
51
defparam ram256x16_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram256x16_inst : SB_RAM256x16
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLK => RCLK_c,
RCLKE => RCLKE_c,
RE => RE_c,
ICE Technology Library
Lattice Semiconductor Corporation Confidential
52
WADDR => WADDR_c,
WCLK=> WCLK_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
MASK => MASK_c,
WE => WE_c
);
SB_RAM256x16NR
SB_RAM256x16NR
// Negative edged Read Clock – i.e. RCLKN
(RDATA, RCLKN, RCLKE, RE, RADDR, WCLK, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM256x16NR
ram256x16NR_inst (
.RDATA(RDATA_c[15:0]),
.RADDR(RADDR_c[7:0]),
.RCLKN(RCLKN_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[7:0]),
.WCLK(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[15:0]),
.WE(WE_c),
.MASK(MASK_c[15:0])
);
defparam ram256x16nr_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nr_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
53
VHDL Instantiation:
ram256x16nr_inst : SB_RAM256x16NR
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLKN => RCLKN_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLK=> WCLK_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
MASK => MASK_c,
WE => WE_c
);
SB_RAM256x16NW
SB_RAM256x16NW
// Negative edged Write Clock – i.e. WCLKN
(RDATA, RCLK, RCLKE, RE, RADDR, WCLKN, WCLKE, WE, WADDR, MASK, WDATA);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
54
Verilog Instantiation:
SB_RAM256x16NW
ram256x16nw_inst (
.RDATA(RDATA_c[15:0]),
.RADDR(RADDR_c[7:0]),
.RCLK(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[7:0]),
.WCLKN(WCLKN_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[15:0]),
.WE(WE_c),
.MASK(MASK_c[15:0])
);
defparam ram256x16nw_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nw_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram256x16nw_inst : SB_RAM256x16NW
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
ICE Technology Library
Lattice Semiconductor Corporation Confidential
55
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLK => RCLK_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLKN=> WCLKN_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
MASK => MASK_c,
WE => WE_c
);
SB_RAM256x16NRNW
SB_RAM256x16NRNW
// Negative edged Read and Write – i.e. RCLKN WRCKLN
(RDATA, RCLKN, RCLKE, RE, RADDR, WCLKN, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM256x16NRNW
ram256x16nrnw_inst (
.RDATA(RDATA_c[15:0]),
.RADDR(RADDR_c[7:0]),
.RCLKN(RCLKN_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[7:0]),
.WCLKN(WCLKN_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[15:0]),
.WE(WE_c),
.MASK(MASK_c[15:0])
);
defparam ram256x16nrnw_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
56
defparam ram256x16nrnw_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram256x16nrnw_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram256x16nrnw_inst : SB_RAM256x16NRNW
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
ICE Technology Library
Lattice Semiconductor Corporation Confidential
57
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLKN => RCLKN_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLKN=> WCLKN_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
MASK => MASK_c,
WE => WE_c
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
58
SB_RAM512x8
The following modules are the complete list of SB_RAM512x8 based primitives
SB_RAM512x8
SB_RAM512x8
//Posedge clock RCLK WCLK
(RDATA, RCLK, RCLKE, RE, RADDR, WCLK, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM512x8
ram512x8_inst (
.RDATA(RDATA_c[7:0]),
.RADDR(RADDR_c[8:0]),
.RCLK(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[8:0]),
.WCLK(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[7:0]),
.WE(WE_c)
);
defparam ram512x8_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
59
defparam ram512x8_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram512x8_inst : SB_RAM512x8
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLK => RCLK_c,
RCLKE => RCLKE_c,
RE => RE_c,
ICE Technology Library
Lattice Semiconductor Corporation Confidential
60
WADDR => WADDR_c,
WCLK=> WCLK_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM512x8NR
SB_RAM512x8NR
// Negative edged Read Clock – i.e. RCLKN
(RDATA, RCLKN, RCLKE, RE, RADDR, WCLK, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM512x8NR
ram512x8nr_inst (
.RDATA(RDATA_c[7:0]),
.RADDR(RADDR_c[8:0]),
.RCLKN(RCLKN_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[8:0]),
.WCLK(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[7:0]),
.WE(WE_c)
);
defparam ram512x8nr_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nr_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
61
VHDL Instantiation:
ram512x8nr_inst: SB_RAM512x8NR
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLKN => RCLKN_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLK=> WCLK_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM512x8NW
SB_RAM512x8NW
// Negative edged Write Clock – i.e. WCLKN
(RDATA, RCLK, RCLKE, RE, RADDR, WCLKN, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM512x8NW
ram512x8nw_inst (
.RDATA(RDATA_c[7:0]),
.RADDR(RADDR_c[8:0]),
ICE Technology Library
Lattice Semiconductor Corporation Confidential
62
.RCLK(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[8:0]),
.WCLKN(WCLKN_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[7:0]),
.WE(WE_c)
);
defparam ram512x8nw_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nw_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram512x8nw_inst: SB_RAM512x8NW
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
ICE Technology Library
Lattice Semiconductor Corporation Confidential
63
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLK => RCLK_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLKN=> WCLKN_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM512x8NRNW
SB_RAM512x8NRNW
// Negative edged Read and Write – i.e. RCLKN WRCKLN
(RDATA, RCLKN, RCLKE, RE, RADDR, WCLKN, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM512x8NRNW
ram512x8nrnw_inst (
.RDATA(RDATA_c[7:0]),
.RADDR(RADDR_c[8:0]),
.RCLKN(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[8:0]),
.WCLKN(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[7:0]),
.WE(WE_c)
);
defparam ram512x8nrnw_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
64
defparam ram512x8nrnw_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram512x8nrnw_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram512x8nrnw_inst: SB_RAM512x8NRNW
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLKN => RCLKN_c,
ICE Technology Library
Lattice Semiconductor Corporation Confidential
65
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLKN=> WCLKN_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
66
SB_RAM1024x4
The following modules are the complete list of SB_RAM1024x4 based primitives
SB_RAM1024x4
SB_RAM1024x4
//Posedge clock RCLK WCLK
(RDATA, RCLK, RCLKE, RE, RADDR, WCLK, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM1024x4
ram1024x4_inst (
.RDATA(RDATA_c[3:0]),
.RADDR(RADDR_c[9:0]),
.RCLK(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[3:0]),
.WCLK(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[9:0]),
.WE(WE_c)
);
defparam ram1024x4_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
67
defparam ram1024x4_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
Ram1024x4_inst: SB_RAM1024x4
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLK => RCLK_c,
ICE Technology Library
Lattice Semiconductor Corporation Confidential
68
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLK=> WCLK_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM1024x4NR
SB_RAM1024x4NR
// Negative edged Read Clock – i.e. RCLKN
(RDATA, RCLKN, RCLKE, RE, RADDR, WCLK, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM1024x4NR
ram1024x4nr_inst (
.RDATA(RDATA_c[3:0]),
.RADDR(RADDR_c[9:0]),
.RCLKN(RCLKN_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[3:0]),
.WCLK(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[9:0]),
.WE(WE_c)
);
defparam ram1024x4nr_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nr_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
69
VHDL Instantiation:
ram1024x4nr_inst: SB_RAM1024x4NR
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLKN => RCLKN_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLK=> WCLK_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM1024x4NW
SB_RAM1024x4NW
// Negative edged Write Clock – i.e. WCLKN
(RDATA, RCLK, RCLKE, RE, RADDR, WCLKN, WCLKE, WE, WADDR, MASK, WDATA);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
70
Verilog Instantiation:
SB_RAM1024x4NW
ram1024x4nw_inst (
.RDATA(RDATA_c[3:0]),
.RADDR(RADDR_c[9:0]),
.RCLK(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[3:0]),
.WCLKN(WCLKN_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[9:0]),
.WE(WE_c)
);
defparam ram1024x4_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram1024x4nw_inst : SB_RAM1024x4NW
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
ICE Technology Library
Lattice Semiconductor Corporation Confidential
71
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLK => RCLK_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLKN=> WCLKN_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM1024x4NRNW
SB_RAM1024x4NRNW
// Negative edged Read and Write – i.e. RCLKN WRCKLN
(RDATA, RCLKN, RCLKE, RE, RADDR, WCLKN, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM1024x4NRNW
ram1024x4nrnw_inst (
.RDATA(RDATA_c[3:0]),
.RADDR(RADDR_c[9:0]),
.RCLKN(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[3:0]),
.WCLKN(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[9:0]),
.WE(WE_c)
);
defparam ram1024x4nrnw_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
72
defparam ram1024x4nrnw_inst.INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram1024x4nrnw_inst.INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram1024x4nrnw_inst : SB_RAM1024x4NRNW
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
ICE Technology Library
Lattice Semiconductor Corporation Confidential
73
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLKN => RCLKN_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLKN=> WCLKN_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
74
SB_RAM2048x2
The following modules are the complete list of SB_RAM2048x2 based primitives
SB_RAM2048x2
SB_RAM2048x2
//Posedge clock RCLK WCLK
(RDATA, RCLK, RCLKE, RE, RADDR, WCLK, WCLKE, WE, WADDR, MASK, WDATA);
Verilog Instantiation:
SB_RAM2048x2
ram2048x2_inst (
.RDATA(RDATA_c[2:0]),
.RADDR(RADDR_c[10:0]),
.RCLK(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[2:0]),
.WCLK(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[10:0]),
.WE(WE_c)
);
defparam ram2048x2_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
75
defparam ram2048x2_inst .INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2_inst .INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
Ram2048x2_inst : SB_RAM2048x2
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLK => RCLK_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLK=> WCLK_c,
WCLKE => WCLKE_c,
ICE Technology Library
Lattice Semiconductor Corporation Confidential
76
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM2048x2NR
SB_RAM2048x2NR
// Negative edged Read Clock – i.e. RCLKN
(RDATA, RCLKN, RCLKE, RE, RADDR, WCLK, WCLKE, WE, WADDR, MASK, WDATA);
SB_RAM2048x2NR
ram2048x2nr_inst (
.RDATA(RDATA_c[2:0]),
.RADDR(RADDR_c[10:0]),
.RCLKN(RCLKN_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[2:0]),
.WCLK(WCLK_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[10:0]),
.WE(WE_c)
);
defparam ram2048x2nr_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nr_inst .INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram2048x2nr_inst : SB_RAM2048x2NR
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
ICE Technology Library
Lattice Semiconductor Corporation Confidential
77
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLKN => RCLKN_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLK=> WCLK_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM2048x2NW
SB_RAM2048x2NW
// Negative edged Write Clock – i.e. WCLKN
(RDATA, RCLK, RCLKE, RE, RADDR, WCLKN, WCLKE, WE, WADDR, MASK, WDATA);
SB_RAM2048x2NW
ram2048x2nw_inst (
.RDATA(RDATA_c[2:0]),
.RADDR(RADDR_c[10:0]),
.RCLK(RCLK_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[2:0]),
.WCLKN(WCLKN_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[10:0]),
.WE(WE_c)
);
defparam ram2048x2nw_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
78
defparam ram2048x2nw_inst .INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nw_inst .INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram2048x2nw_inst: SB_RAM2048x2NW
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
ICE Technology Library
Lattice Semiconductor Corporation Confidential
79
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLK => RCLK_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLKN=> WCLKN_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
SB_RAM2048x2NRNW
SB_RAM2048x2NRNW
// Negative edged Read and Write – i.e. RCLKN WRCKLN
(RDATA, RCLKN, RCLKE, RE, RADDR, WCLKN, WCLKE, WE, WADDR, MASK, WDATA);
SB_RAM2048x2NRNW
ram2048x2nrnw_inst (
.RDATA(RDATA_c[2:0]),
.RADDR(RADDR_c[10:0]),
.RCLKN(RCLKN_c),
.RCLKE(RCLKE_c),
.RE(RE_c),
.WADDR(WADDR_c[2:0]),
.WCLKN(WCLKN_c),
.WCLKE(WCLKE_c),
.WDATA(WDATA_c[10:0]),
.WE(WE_c)
);
defparam ram2048x2nrnw_inst.INIT_0 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_1 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_2 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_3 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_4 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_5 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_6 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_7 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_8 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_9 =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_A =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_B =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_C =
256'h0000000000000000000000000000000000000000000000000000000000000000;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
80
defparam ram2048x2nrnw_inst .INIT_D =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_E =
256'h0000000000000000000000000000000000000000000000000000000000000000;
defparam ram2048x2nrnw_inst .INIT_F =
256'h0000000000000000000000000000000000000000000000000000000000000000;
VHDL Instantiation:
ram2048x2nrnw_inst : SB_RAM2048x2NRNW
generic map (
INIT_0 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_1 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_2 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_3 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_4 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_5 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_6 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_7 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_8 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_9 =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_A =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_B =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_C =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_D =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_E =>
X"0000000000000000000000000000000000000000000000000000000000000000",
INIT_F => X"0000000000000000000000000000000000000000000000000000000000000000"
)
port map (
RDATA => RDATA_c,
RADDR => RADDR_c,
RCLKN => RCLKN_c,
RCLKE => RCLKE_c,
RE => RE_c,
WADDR => WADDR_c,
WCLKN=> WCLKN_c,
WCLKE => WCLKE_c,
WDATA => WDATA_c,
WE => WE_c
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
81
SB_RAM40_4K
SB_RAM40_4K is the basic physical RAM primitive which can be instantiated and configured to different
depth and dataports. The SB_RAM40_4K block has a size of 4K bits with separate write and read ports,
each with independent control signals. By default, input and output data is 16 bits wide, although the data
width is configurable using the READ_MODE and WRITE_MODE parameters. The data contents of the
SB_RAM40_4K block are optionally pre-loaded during ICE device configuration.
SB_RAM40_4K Naming Convention Rules
RAM Primitive Name
SB_RAM40_4K
SB_RAM40_4KNR
SB_RAM40_4KNW
SB_RAM40_4KNRNW
Description
Posedge Read clock, Posedge Write clock
Negedge Read clock, Posedge Write clock
Posedge Read clock, Negedge Write clock
Negedge Read clock, Negedge Write clock
The following table lists the signals for both ports.
SB_RAM40_4K RAM Port Signals
Signal Name
Direction
WDATA[15:0]
MASK[15:0]*
Input
Input
WADDR[7:0]
WE
WCLK
WCLKE
RDATA[15:0]
RADDR[7:0]
RE
RCLK
RCLKE
Input
Input
Input
Input
Output
Input
Input
Input
Input
Description
Write Data input
Bit-line Write Enable input, active low. Applicable only when
WRITE_MODE parameter is set to 0.
Write Address input. Selects up to 256 possible locations
Write Enable input, active high
Write Clock input, rising-edge active
Write Clock Enable input
Read Data output
Read Address input. Selects one of 256 possible locations
Read Enable input, active high
Read Clock input, rising-edge active
Read Clock Enable input
ICE Technology Library
Lattice Semiconductor Corporation Confidential
82
Parameter
Name
Description
Parameter
Value
INIT_0, …
…,INIT_F
RAM Initialization Data. Passed using 16
parameter strings, each comprising 256
bits. (16x256=4096 total bits)
Sets the RAM block write port
configuration
INIT_0 to
INIT_F
WRITE_MODE
READ_MODE
Sets the RAM block read port
configuration
0
1
2
3
0
1
2
3
Configuration
Initialize the RAM with
predefined value
256x16
512x8
1024x4
2048x2
256x16
512x8
1024x4
2048x2
SB_RAM40_4K
Verilog Instantiation:
// Physical RAM Instance without Pre Initialization
SB_RAM40_4K ram40_4kinst_physical (
.RDATA(RDATA),
.RADDR(RADDR),
.WADDR(WADDR),
.MASK(MASK),
.WDATA(WDATA),
.RCLKE(RCLKE),
.RCLK(RCLK),
.RE(RE),
.WCLKE(WCLKE),
.WCLK(WCLK),
.WE(WE)
);
defparam ram40_4kinst_physical.READ_MODE=0;
defparam ram40_4kinst_physical.WRITE_MODE=0;
VHDL Instantiation:
-- Physical RAM Instance without Pre Initialization
ram40_4kinst_physical : SB_RAM40_4K
generic map (
READ_MODE => 0,
WRITE_MODE= >0 )
port map (
RDATA=>RDATA,
RADDR=>RADDR,
WADDR=>WADDR,
MASK=>MASK,
WDATA=>WDATA,
RCLKE=>RCLKE,
RCLK=>RCLK,
RE=>RE,
WCLKE=>WCLKE,
WCLK=>WCLK,
WE=>WE
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
83
SB_RAM40_4KNR
Verilog Instantiation:
// Physical RAM Instance without Pre Initialization
SB_RAM40_4KNR ram40_4knrinst_physical (
.RDATA(RDATA),
.RADDR(RADDR),
.WADDR(WADDR),
.MASK(MASK),
.WDATA(WDATA),
.RCLKE(RCLKE),
.RCLKN(RCLKN),
.RE(RE),
.WCLKE(WCLKE),
.WCLK(WCLK),
.WE(WE)
);
defparam ram40_4knrinst_physical.READ_MODE=0;
defparam ram40_4knrinst_physical.WRITE_MODE=0;
VHDL Instantiation:
-- Physical RAM Instance without Pre Initialization
ram40_4knrinst_physical : SB_RAM40_4KNR
generic map (
READ_MODE => 0,
WRITE_MODE= >0
)
port map (
RDATA=>RDATA,
RADDR=>RADDR,
WADDR=>WADDR,
MASK=>MASK,
WDATA=>WDATA,
RCLKE=>RCLKE,
RCLKN=>RCLKN,
RE=>RE,
WCLKE=>WCLKE,
WCLK=>WCLK,
WE=>WE
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
84
SB_RAM40_4KNW
Verilog Instantiation:
// Physical RAM Instance without Pre Initialization
SB_RAM40_4KNW ram40_4knwinst_physical (
.RDATA(RDATA),
.RADDR(RADDR),
.WADDR(WADDR),
.MASK(MASK),
.WDATA(WDATA),
.RCLKE(RCLKE),
.RCLK(RCLK),
.RE(RE),
.WCLKE(WCLKE),
.WCLKN(WCLKN),
.WE(WE)
);
defparam ram40_4knwinst_physical.READ_MODE=0;
defparam ram40_4knwinst_physical.WRITE_MODE=0;
VHDL Instantiation:
-- Physical RAM Instance without Pre Initialization
ram40_4knwinst_physical : SB_RAM40_4KNW
generic map (
READ_MODE => 0,
WRITE_MODE= >0
)
port map (
RDATA=>RDATA,
RADDR=>RADDR,
WADDR=>WADDR,
MASK=>MASK,
WDATA=>WDATA,
RCLKE=>RCLKE,
RCLK=>RCLK,
RE=>RE,
WCLKE=>WCLKE,
WCLKN=>WCLKN,
WE=>WE
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
85
SB_RAM40_4KNRNW
Verilog Instantiation:
// Physical RAM Instance without Pre Initialization
SB_RAM40_4KNRNW ram40_4knrnwinst_physical (
.RDATA(RDATA),
.RADDR(RADDR),
.WADDR(WADDR),
.MASK(MASK),
.WDATA(WDATA),
.RCLKE(RCLKE),
.RCLKN(RCLKN),
.RE(RE),
.WCLKE(WCLKE),
.WCLKN(WCLKN),
.WE(WE)
);
defparam ram40_4knrnwinst_physical.READ_MODE=0;
defparam ram40_4knrnwinst_physical.WRITE_MODE=0;
VHDL Instantiation:
-- Physical RAM Instance without Pre Initialization
ram40_4knrnwinst_physical : SB_RAM40_4KNRNW
generic map (
READ_MODE => 0,
WRITE_MODE= >0
)
port map (
RDATA=>RDATA,
RADDR=>RADDR,
WADDR=>WADDR,
MASK=>MASK,
WDATA=>WDATA,
RCLKE=>RCLKE,
RCLKN=>RCLKN,
RE=>RE,
WCLKE=>WCLKE,
WCLKN=>WCLKN,
WE=>WE
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
86
IO Primitives
SB_IO
The SB_IO block contains five registers. The following figure and Verilog template illustrate the complete
user accessible logic diagram, and its Verilog instantiation.
Default Signal Values
The iCEcube2 software assigns the logic ‘0’ value to all unconnected input ports except for
CLOCK_ENABLE.
Note that explicitly connecting a logic ‘1’ value to port CLOCK_ENABLE will result in a non-optimal
implementation, since an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep
the Input and Output registers always enabled, it is recommended that port CLOCK_ENABLE be left
unconnected.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
87
Input and Output Pin Function Tables
Input and Output functions are independently selectable via PIN_TYPE [1:0] and PIN_TYPE [5:2]
parameter settings respectively. Specific IO functions are defined by the combination of both attributes.
This means that the complete number of combinations is 64, although some combinations are not valid
and not defined below.
Note that the selection of IO Standards such as SSTL and LVCMOS are not defined by these tables.
Input Pin Function Table
#
Pin Function Mnemonic
Functional Description of Package Pin
Input Operation
PIN_TYPE[1:0]
1
2
PIN_INPUT
PIN_INPUT_LATCH
0
1
1
1
3
4
PIN_INPUT_REGISTERED
PIN_INPUT_REGISTERED
_LATCH
0
1
0
0
5
PIN_INPUT_DDR
0
0
Simple input pin (D_IN_0)
Disables internal data changes on the
physical input pin by latching the value.
Input data is registered in input cell
Disables internal data changes on the
physical input pin by latching the value on
the input register
Input 'DDR' data is clocked out on rising
and falling clock edges. Use the D_IN_0
and D_IN_1 pins for DDR operation.
Output Pin Function table
#
Pin Function Mnemonic
PIN_TYPE[5:2]
1
2
3
PIN_NO_OUTPUT
PIN_OUTPUT
PIN_OUTPUT_TRISTATE
0
0
1
0
1
0
0
1
1
0
0
0
4
PIN_OUTPUT_ENABLE_REGISTERED
1
1
1
0
5
6
PIN_OUTPUT_REGISTERED
PIN_OUTPUT_REGISTERED_ENABLE
0
1
1
0
0
0
1
1
7
1
1
0
1
8
PIN_OUTPUT_REGISTERED_ENABLE
_REGISTERED
PIN_OUTPUT_DDR
0
1
0
0
9
PIN_OUTPUT_DDR_ENABLE
1
0
0
0
10
PIN_OUTPUT_DDR_ENABLE_REGIST
ERED
PIN_OUTPUT_REGISTERED_INVERT
ED
PIN_OUTPUT_REGISTERED_ENABLE
__INVERTED
PIN_OUTPUT_REGISTERED_ENABLE
_REGISTERED_INVERTED
1
1
0
0
0
1
1
1
1
0
1
1
1
1
1
1
11
12
13
ICE Technology Library
Lattice Semiconductor Corporation Confidential
Functional Description of Package Pin
Output Operation
Disables the output function
Simple output pin, (no enable)
The output pin may be tristated using the
enable
The output pin may be tristated using a
registered enable signal
Output registered, (no enable)
Output registered with enable (enable is
not registered)
Output registered and enable registered
Output 'DDR' data is clocked out on
rising and falling clock edges
Output data is clocked out on rising and
falling clock edges
Output 'DDR' data with registered enable
signal
Output registered signal is inverted
Output signal is registered and inverted,
(no enable function)
Output signal is registered and inverted,
the enable/tristate control is registered.
88
Syntax Verilog Use
Output Pin Function is the bit vector associated with PIN_TYPE [5:2] and Input Pin Function is the bit
vector associated with PIN_TYPE [1:0], resulting in a 6 bit value PIN_TYPE [5:0]
defparam my_generic_IO.PIN_TYPE = 6’b{Output Pin Function, Input Pin Function};
DDR IO Configuration
The following setting configures the SB_IO into a DDR IO.
defparam my_DDR_IO.PIN_TYPE = 6’b100000;
// PIN_TYPE [5:2] = 1000
// PIN_TYPE [1:0] = 00
This creates a DDR IO pin whereby the input data is clocked in on both the rising and falling input clock
edges.
The output 'DDR' data is clocked out on rising and falling output clock edges, and the output may be tristated, using the output enable port of the SB_IO.
High Drive SB_IO
IO’s in iCE40/iCE40LM device can be configured with different drive strengths to increase the IO output
current. To configure an SB_IO with specific drive value, the user needs to specify the
“DRIVE_STRENGTH” synthesis attribute on the SB_IO instance and the IO should be configured as
output-only registered IO.
Synthesis Attribute Syntax:
/* synthesis DRIVE_STRENGTH = <Drive value> */
Drive Value:
Drive Strength Value
x1
x2
x3
Description.
Default drive strength. No replication of SB_IO.
Increase default drive strength by 2. SB_IO replicated
once.
Increase default drive strength by 3. SB_IO replicated
twice.
Note: High drive SB_IO is available only in selected iCE40/iCE40LM packages. Refer to Chapter 12 in
iCEcube2_userguide for the list of supported device packages.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
89
Pull Up Resistor Configuration.
For iCE40UL device, user can configure the internal pull up resistor strength of an IO to a predefined
resistor value via attribute settings. By default, all the IO’s are weakly pulled up by 100K internal resistor.
The PULLUP_RESISTOR attribute is effective only when PULLUP parameter is set to 1.
Synthesis Attribute Syntax:
/* synthesis PULLUP_RESISTOR = "3P3K" */
Resistor Value:
Resistor Value
Description.
"3P3K"
Pull up resistor level is 3.3K.
"6P8K"
Pull up resistor level is 6.8K.
"10K"
Pull up resistor level is 10K.
"100K"
Pull up resistor level is 100K. (Default)
Note: PULLUP_RESISTOR attribute is supported only for iCE40UL devices.
Verilog Instantiation
SB_IO
IO_PIN_INST
(
.PACKAGE_PIN (Package_Pin),
.LATCH_INPUT_VALUE (latch_input_value),
.CLOCK_ENABLE (clock_enable),
.INPUT_CLK (input_clk),
.OUTPUT_CLK (output_clk),
.OUTPUT_ENABLE (output_enable),
.D_OUT_0 (d_out_0),
.D_OUT_1 (d_out_1),
.D_IN_0 (d_in_0),
.D_IN_1 (d_in_1)
//
//
//
//
//
//
//
//
//
//
//
//
//
//
//
//
User’s Pin signal name
Latches/holds the Input value
Clock Enable common to input and
output clock
Clock for the input registers
Clock for the output registers
Output Pin Tristate/Enable
control
Data 0 – out to Pin/Rising clk
edge
Data 1 - out to Pin/Falling clk
edge
Data 0 - Pin input/Rising clk
edge
Data 1 – Pin input/Falling clk
edge
) /* synthesis DRIVE_STRENGTH= x2 */;
defparam IO_PIN_INST.PIN_TYPE = 6'b000000;
// See Input and Output Pin Function Tables.
// Default value of PIN_TYPE = 6’000000 i.e.
// an input pad, with the input signal
// registered.
defparam IO_PIN_INST.PULLUP = 1'b0;
// By default, the IO will have NO pull up.
// This parameter is used only on bank 0, 1,
// and 2. Ignored when it is placed at bank 3
defparam IO_PIN_INST.NEG_TRIGGER = 1'b0;
// Specify the polarity of all FFs in the IO to
// be falling edge when NEG_TRIGGER = 1.
// Default is rising edge.
defparam IO_PIN_INST.IO_STANDARD = "SB_LVCMOS";
// Other IO standards are supported in bank 3
// only: SB_SSTL2_CLASS_2, SB_SSTL2_CLASS_1,
// SB_SSTL18_FULL, SB_SSTL18_HALF, SB_MDDR10,
// SB_MDDR8, SB_MDDR4, SB_MDDR2 etc.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
90
Global Buffer Primitives
SB_GB_IO
Default Signal Values
The iCEcube2 software assigns the logic ‘0’ value to all unconnected input ports except for
CLOCK_ENABLE.
Note that explicitly connecting a logic ‘1’ value to port CLOCK_ENABLE will result in a non-optimal
implementation, since an extra LUT will be used to generate the Logic ‘1’. If the user’s intention is to keep
the Input and Output registers always enabled, it is recommended that port CLOCK_ENABLE be left
unconnected.
Verilog Instantiation
SB_GB_IO My_Clock_Buffer_Package_Pin (
.PACKAGE_PIN (Package_Pin),
.LATCH_INPUT_VALUE (latch_input_value),
.CLOCK_ENABLE (clock_enable),
ICE Technology Library
Lattice Semiconductor Corporation Confidential
// A users external Clock reference
pin
// User’s Pin signal name
// Latches/holds the Input value
// Clock Enable common to input and
// output clock
91
.INPUT_CLK (input_clk),
.OUTPUT_CLK (output_clk),
.OUTPUT_ENABLE (output_enable),
.D_OUT_0 (d_out_0),
.D_OUT_1 (d_out_1),
.D_IN_0 (d_in_0),
.D_IN_1 (d_in_1)
//
//
//
//
//
//
//
//
//
//
//
//
Clock for the input registers
Clock for the output registers
Output Pin Tristate/Enable
control
Data 0 – out to Pin/Rising clk
edge
Data 1 - out to Pin/Falling clk
edge
Data 0 - Pin input/Rising clk
edge
Data 1 – Pin input/Falling clk
edge
.GLOBAL_BUFFER_OUTPUT (Global_Buffered_User_Clock)
// Example use – clock buffer
//driven from the input pin
);
defparam
My_Clock_Buffer_Package_Pin.PIN_TYPE = 6'b000000;
// See Input and Output Pin Function Tables.
// Default value of PIN_TYPE = 6’000000 i.e.
// an input pad, with the input signal
// registered
Note that this primitive is a superset of the SB_IO primitive, and includes the connectivity to drive a Global
Buffer. For example SB_GB_IO pins are likely to be used for external Clocks.
SB_GB Primitive
Verilog Instantiation
SB_GB My_Global_Buffer_i (
//Required for a user’s internally generated
//FPGA signal that is heavily loaded and
//requires global buffering. For example, a
//user’s logic-generated clock.
.USER_SIGNAL_TO_GLOBAL_BUFFER (Users_internal_Clk),
.GLOBAL_BUFFER_OUTPUT ( Global_Buffered_User_Signal)
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
92
PLL Primitives
The Phase Lock Loop (PLL) function is offered as a feature in certain iCE device packages.
It is strongly recommended that the configuration of the PLL primitives be accomplished through the use
of the PLL Configuration tool that is offered as part of the iCEcube2 software.
iCE40 PLL Primitives
There are 5 primitives that represent the PLL function in the iCEcube2 software viz. SB_PLL40_CORE,
SB_PLL40_PAD, SB_PLL40_2_PAD, SB_PLL40_2F_CORE and SB_PLL40_2F_PAD for the ice40
device family. A short description of each primitive and its ports/parameters is provided in the following
sections.
It is strongly recommended that the configuration of the PLL primitives be accomplished through the use
of the PLL Configuration tool that is offered as part of the iCEcube2 software.
SB_PLL40_CORE
The SB_PLL40_CORE primitive should be used when the source clock of the PLL is driven by FPGA
routing i.e. when the PLL source clock originates on the FPGA or is driven by an input pad that is not in
the bottom IO bank (IO Bank 2).
Ports
REFERENCECLK: PLL source clock that serves as the input to the SB_PLL40_CORE primitive.
PLLOUTGLOBAL: Output clock generated by the PLL, drives a global clock network on the FPGA.
PLLOUTCORE: Output clock generated by the PLL, drives regular FPGA routing. The frequency
generated on this output is the same as the frequency of the clock signal generated on the
PLLOUTLGOBAL port.
LOCK: Output port, when HIGH, indicates that the signal on PLLOUTGLOBAL/PLLOUTCORE is locked
to the PLL source on REFERENCECLK.
EXTFEEDBACK: External feedback input to PLL. Enabled when the FEEDBACK_PATH parameter is set
to EXTERNAL.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
93
DYNAMICDELAY: 7 bit input bus that enables dynamic control of the delay contributed by the Fine Delay
Adjust Block. The Fine Delay Adjust Block is used when there is a need to adjust the phase alignment of
PLLOUTGLOBAL/PLLOUTCORE with respect to REFERENCECLK. The DYNAMICDELAY port controls
are enabled when the DELAY_ADJUSTMENT_MODE parameter is set to DYNAMIC.
RESETB: Active low input that asynchronously resets the PLL.
BYPASS: Input signal, when asserted, connects the signal on REFERENCECLK to
PLLOUTCORE/PLLOUTGLOBAL pins.
LATCHINPUTVALUE: Active high input, when enabled, forces the PLL into low-power mode. The
PLLOUTGLOBAL/PLLOUTCORE pins are held static at their last value. This function is enabled when
the parameter ENABLE_ICEGATE is set to ‘1’.
SCLK, SDI, SDO: These pins are used only for internal testing purposes, and need not be instantiated by
users.
Parameters
The SB_PLL40_CORE primitive requires configuration through the specification of the following
parameters. It is strongly recommended that the configuration of the PLL primitives be accomplished
through the use of the PLL Configuration tool that is offered as part of the iCEcube2 software.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
94
Parameter Name
FEEDBACK_PATH
Description
Selects the feedback path
to the PLL
Parameter Value
SIMPLE
DELAY
PHASE_AND_DELAY
EXTERNAL
DELAY_ADJUSTMENT_MO
DE_FEEDBACK
Selects the mode for the
Fine Delay Adjust block in
the feedback path
FIXED
DYNAMIC
FDA_FEEDBACK
Sets a constant value for
the Fine Delay Adjust Block
in the feedback path
DELAY_ADJUSTMENT_MO
DE_RELATIVE
Selects the mode for the
Fine Delay Adjust block
0, 1,…,15
FIXED
DYNAMIC
FDA_RELATIVE
Sets a constant value for
the Fine Delay Adjust Block
SHIFTREG_DIV_MODE
Selects shift register
configuration
PLLOUT_SELECT
Selects the signal to be
output at the
PLLOUTCORE and
PLLOUTGLOBAL ports
0, 1,…,15
0,1
SHIFTREG_0deg
SHIFTREG_90deg
GENCLK
GENCLK_HALF
DIVR
REFERENCECLK divider
ICE Technology Library
Lattice Semiconductor Corporation Confidential
0,1,2,…,15
Description
Feedback is internal to the PLL,
directly from VCO
Feedback is internal to the PLL,
through the Fine Delay Adjust
Block
Feedback is internal to the PLL,
through the Phase Shifter and the
Fine Delay Adjust Block
Feedback path is external to the
PLL, and connects to
EXTFEEDBACK pin. Also uses
the Fine Delay Adjust Block.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the FDA_FEEDBACK
parameter setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[3:0] pins
The PLLOUTGLOBAL &
PLLOUTCORE signals are delay
compensated by (n+1)*150 ps,
where n = FDA_FEEDBACK only
if the setting of the
DELAY_ADJUSTMENT_MODE_F
EEDBACK is FIXED.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the FDA_RELATIVE
parameter setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[7:4] pins
The PLLOUTGLOBALA &
PLLOUTCOREA signals are
additionally delayed by (n+1)*150
ps, where n = FDA_RELATIVE.
Used if
DELAY_ADJUSTMENT_MODE_
RELATIVE is “FIXED”.
Used when FEEDBACK_PATH is
“PHASE_AND_DELAY”.
0Divide by 4
1Divide by 7
o
0 phase shift only if the setting of
FEEDBACK_PATH is
“PHASE_AND_DELAY”
o
90 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY” and
SHIFTREG_DIV_MODE=0
The internally generated PLL
frequency will be output without
any phase shift.
The internally generated PLL
frequency will be divided by 2 and
then output. No phase shift.
These parameters are used to
95
DIVF
DIVQ
FILTER_RANGE
EXTERNAL_DIVIDE_FACT
OR
Feedback divider
VCO Divider
PLL Filter Range
Divide-by factor of a divider
in external feedback path
ENABLE_ICEGATE
Enables the PLL powerdown control
ICE Technology Library
Lattice Semiconductor Corporation Confidential
0,1,..,63
1,2,…,6
0,1,…,7
User specified value.
Default 1
0
1
control the output frequency,
depending on the
FEEDBACK_PATH setting.
Specified only when there is a
user-implemented divider in the
external feedback path.
Power-down control disabled
Power-down controlled by
LATCHINPUTVALUE input
96
SB_PLL40_PAD
The SB_PLL40_PAD primitive should be used when the source clock of the PLL is driven by an input pad
that is located in the bottom IO bank (IO Bank 2) or the top IO bank (IO Bank 0), and the source clock is
not required inside the FPGA.
Ports
PACKAGEPIN: PLL REFERENCE CLOCK pin that serves as the input to the SB_PLL40_PAD primitive.
PLLOUTGLOBAL: Output clock generated by the PLL, drives a global clock network on the FPGA.
PLLOUTCORE: Output clock generated by the PLL, drives regular FPGA routing. The frequency
generated on this output is the same as the frequency of the clock signal generated on the
PLLOUTLGOBAL port.
LOCK: Output port, when HIGH, indicates that the signal on PLLOUTGLOBAL/PLLOUTCORE is locked
to the PLL source on PACKAGEPIN.
EXTFEEDBACK: External feedback input to PLL. Enabled when the FEEDBACK_PATH parameter is set
to EXTERNAL.
DYNAMICDELAY: 7 bit input bus that enables dynamic control of the delay contributed by the Fine Delay
Adjust Block. The Fine Delay Adjust Block is used when there is a need to adjust the phase alignment of
PLLOUTGLOBAL/PLLOUTCORE with respect to PACKAGEPIN. The DYNAMICDELAY port controls are
enabled when the DELAY_ADJUSTMENT_MODE parameter is set to DYNAMIC.
RESETB: Active low input that asynchronously resets the PLL.
BYPASS: Input signal, when asserted, connects the signal on PACKAGEPIN to
PLLOUTCORE/PLLOUTGLOBAL pins.
LATCHINPUTVALUE: Active high input, when enabled, forces the PLL into low-power mode. The
PLLOUTGLOBAL/PLLOUTCORE pins are held static at their last value. This function is enabled when
the parameter ENABLE_ICEGATE is set to ‘1’.
SCLK, SDI, SDO: These pins are used only for internal testing purposes, and need not be instantiated by
users.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
97
Parameters
The SB_PLL40_PAD primitive requires configuration through the specification of the following
parameters. It is strongly recommended that the configuration of the PLL primitives be accomplished
through the use of the PLL Configuration tool that is offered as part of the iCEcube2 software.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
98
Parameter Name
FEEDBACK_PATH
Description
Selects the feedback path
to the PLL
Parameter Value
SIMPLE
DELAY
PHASE_AND_DELAY
EXTERNAL
DELAY_ADJUSTMENT_MO
DE_FEEDBACK
Selects the mode for the
Fine Delay Adjust block in
the feedback path
FIXED
DYNAMIC
FDA_FEEDBACK
Sets a constant value for
the Fine Delay Adjust Block
in the feedback path
DELAY_ADJUSTMENT_MO
DE_RELATIVE
Selects the mode for the
Fine Delay Adjust block
0, 1,…,15
FIXED
DYNAMIC
FDA_RELATIVE
Sets a constant value for
the Fine Delay Adjust Block
SHIFTREG_DIV_MODE
Selects shift register
configuration
PLLOUT_SELECT
Selects the signal to be
output at the
PLLOUTCORE and
PLLOUTGLOBAL ports
0, 1,…,15
0,1
SHIFTREG_0deg
SHIFTREG_90deg
GENCLK
GENCLK_HALF
DIVR
REFERENCECLK divider
ICE Technology Library
Lattice Semiconductor Corporation Confidential
0,1,2,…,15
Description
Feedback is internal to the PLL,
directly from VCO
Feedback is internal to the PLL,
through the Fine Delay Adjust
Block
Feedback is internal to the PLL,
through the Phase Shifter and the
Fine Delay Adjust Block
Feedback path is external to the
PLL, and connects to
EXTFEEDBACK pin. Also uses
the Fine Delay Adjust Block.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the FDA_FEEDBACK
parameter setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY [3:0] pins
The PLLOUTGLOBAL &
PLLOUTCORE signals are delay
compensated by (n+1)*150 ps,
where n = FDA_FEEDBACK only
if the setting of the
DELAY_ADJUSTMENT_MODE_F
EEDBACK is FIXED.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the FDA_RELATIVE
parameter setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[7:4] pins
The PLLOUTGLOBALA &
PLLOUTCOREA signals are
additionally delayed by (n+1)*150
ps, where n = FDA_RELATIVE.
Used if
DELAY_ADJUSTMENT_MODE_
RELATIVE is “FIXED”.
Used when FEEDBACK_PATH is
“PHASE_AND_DELAY”.
0Divide by 4
1Divide by 7
o
0 phase shift only if the setting of
FEEDBACK_PATH is
“PHASE_AND_DELAY”
o
90 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY” and
SHIFTREG_DIV_MODE=0
The internally generated PLL
frequency will be output without
any phase shift.
The internally generated PLL
frequency will be divided by 2 and
then output. No phase shift.
These parameters are used to
99
DIVF
DIVQ
FILTER_RANGE
EXTERNAL_DIVIDE_FACT
OR
Feedback divider
VCO Divider
PLL Filter Range
Divide-by factor of a divider
in external feedback path
ENABLE_ICEGATE
Enables the PLL powerdown control
ICE Technology Library
Lattice Semiconductor Corporation Confidential
0,1,..,63
1,2,…,6
0,1,…,7
User specified value.
Default 1
0
1
control the output frequency,
depending on the
FEEDBACK_PATH setting.
Specified only when there is a
user-implemented divider in the
external feedback path.
Power-down control disabled
Power-down controlled by
LATCHINPUTVALUE input
100
SB_PLL40_2_PAD
The SB_PLL40_2_PAD primitive should be used when the source clock of the PLL is driven by an input
pad that is located in the bottom IO bank (IO Bank 2) or the top IO bank (IO Bank 0), and in addition to
the PLL output, the source clock is also required inside the FPGA.
Port A
(Source Clock)
Port B
(Generated Clock)
Ports
PACKAGEPIN: PLL REFERENCE CLOCK pin that serves as the input to the SB_PLL40_2_PAD
primitive.
PLLOUTGLOBALA: The signal on PACKAGEPIN appears on the FPGA at this pin, and drives a global
clock network on the FPGA. Do not use this pin in an external feedback path to the PLL.
PLLOUTCOREA: The signal on PACKAGEPIN appears on the FPGA at this pin, which drives regular
FPGA routing. Do not use this pin in an external feedback path to the PLL.
PLLOUTGLOBALB: Output clock generated by the PLL, drives a global clock network on the FPGA.
PLLOUTCOREB: Output clock generated by the PLL, drives regular FPGA routing. The frequency
generated on this output is the same as the frequency of the clock signal generated on the
PLLOUTLGOBAL port.
LOCK: Output port, when HIGH, indicates that the signal on PLLOUTGLOBALB/PLLOUTCOREB is
locked to the PLL source on PACKAGEPIN.
EXTFEEDBACK: External feedback input to PLL. Enabled when the FEEDBACK_PATH parameter is set
to EXTERNAL.
DYNAMICDELAY: 4 bit input bus that enables dynamic control of the delay contributed by the Fine Delay
Adjust Block. The Fine Delay Adjust Block is used when there is a need to adjust the phase alignment of
PLLOUTGLOBAL/PLLOUTCORE with respect to PACKAGEPIN. The DYNAMICDELAY port controls are
enabled when the DELAY_ADJUSTMENT_MODE parameter is set to DYNAMIC.
RESET: Active low input that asynchronously resets the PLL.
BYPASS: Input signal, when asserted, connects the signal on PACKAGEPIN to
PLLOUTCORE/PLLOUTGLOBAL pins.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
101
LATCHINPUTVALUE: Active high input, when enabled, forces the PLL into low-power mode. The
PLLOUTGLOBALA/PLLOUTCOREA pins are held static at their last value only when the parameter
ENABLE_ICEGATE_PORTA is set to ‘1’, and the LATCHINPUTVALUE signal is asserted. The
PLLOUTGLOBALB/PLLOUTCOREB pins are held static at their last value only when the parameter
ENABLE_ICEGATE_PORTB is set to ‘1’, and the LATCHINPUTVALUE signal is asserted.
SCLK, SDI, SDO: These pins are used only for internal testing purposes, and need not be instantiated by
users.
Parameters
The SB_PLL40_2_PAD primitive requires configuration through the specification of the following
parameters. It is strongly recommended that the configuration of the PLL primitives be accomplished
through the use of the PLL Configuration tool that is offered as part of the iCEcube2 software.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
102
Parameter Name
FEEDBACK_PATH
Description
Selects the feedback path
to the PLL
Parameter Value
SIMPLE
DELAY
PHASE_AND_DELAY
EXTERNAL
DELAY_ADJUSTMENT_MODE
_FEEDBACK
Selects the mode for the
Fine Delay Adjust block in
the feedback path
FIXED
DYNAMIC
FDA_FEEDBACK
Sets a constant value for
the Fine Delay Adjust
Block in the feedback path
DELAY_ADJUSTMENT_MODE
_RELATIVE
Selects the mode for the
Fine Delay Adjust block
0, 1,…,15
FIXED
DYNAMIC
FDA_RELATIVE
Sets a constant value for
the Fine Delay Adjust
Block
SHIFTREG_DIV_MODE
Selects shift register
configuration
PLLOUT_SELECT_PORTB
Selects the signal to be
output at the
PLLOUTCOREB and
PLLOUTGLOBALB ports
0, 1,…,15
0,1
SHIFTREG_0deg
SHIFTREG_90deg
GENCLK
GENCLK_HALF
ICE Technology Library
Lattice Semiconductor Corporation Confidential
Description
Feedback is internal to the PLL,
directly from VCO
Feedback is internal to the PLL,
through the Fine Delay Adjust
Block
Feedback is internal to the PLL,
through the Phase Shifter and
the Fine Delay Adjust Block
Feedback path is external to the
PLL, and connects to
EXTFEEDBACK pin. Also uses
the Fine Delay Adjust Block.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the
FDA_FEEDBACK parameter
setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[3:0] pins
The PLLOUTGLOBAL &
PLLOUTCORE signals are delay
compensated by (n+1)*150 ps,
where n = FDA_FEEDBACK only
if the setting of the
DELAY_ADJUSTMENT_MODE_
FEEDBACK is FIXED.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the FDA_RELATIVE
parameter setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[7:4] pins
The PLLOUTGLOBALA &
PLLOUTCOREA signals are
delayed w.r.t. the Port B signals,
by (n+1)*150 ps, where n =
FDA_RELATIVE. Used if
DELAY_ADJUSTMENT_MODE_
RELATIVE is “FIXED”.
Used when FEEDBACK_PATH
is “PHASE_AND_DELAY”.
0Divide by 4
1Divide by 7
o
0 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY”
o
90 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY” and
SHIFTREG_DIV_MODE=0
The internally generated PLL
frequency will be output to PortB.
No phase shift.
The internally generated PLL
frequency will be divided by 2
and then output to PORTB. No
phase shift.
103
DIVR
DIVF
DIVQ
FILTER_RANGE
EXTERNAL_DIVIDE_FACTOR
ENABLE_ICEGATE_PORTA
ENABLE_ICEGATE_PORTB
REFERENCECLK divider
Feedback divider
VCO Divider
PLL Filter Range
Divide-by factor of a
divider in external
feedback path
Enables the PLL powerdown control
Enables the PLL powerdown control
0,1,2,…,15
0,1,..,63
1,2,…,6
0,1,…,7
User specified value.
Default 1
0
1
0
1
These parameters are used to
control the output frequency,
depending on the
FEEDBACK_PATH setting.
Specified only when there is a
user-implemented divider in the
external feedback path.
Power-down control disabled
Power-down controlled by
LATCHINPUTVALUE input
Power-down control disabled
Power-down controlled by
LATCHINPUTVALUE input
SB_PLL40_2F_CORE
The SB_PLL40_2F_CORE primitive should be used when PLL is used to generate 2 different output
frequencies, and the source clock of the PLL is driven by FPGA routing i.e. when the PLL source clock
originates on the FPGA.
Port A (Generated
Clock)
Generated Clock)
Port B
(Generated Clock)
Ports
REFERENCECLK: PLL source clock that serves as the input to the SB_PLL40_2F_CORE primitive.
PLLOUTGLOBALA: Output clock generated by the PLL, drives a global clock network on the FPGA.
PLLOUTCOREA: Output clock generated by the PLL, drives regular FPGA routing. The frequency
generated on this output is the same as the frequency of the clock signal generated on the
PLLOUTLGOBALA port.
PLLOUTGLOBALB: Output clock generated by the PLL, drives a global clock network on the FPGA.
PLLOUTCOREB: Output clock generated by the PLL, drives regular FPGA routing. The frequency
generated on this output is the same as the frequency of the clock signal generated on the
PLLOUTLGOBALB port.
LOCK: Output port, when HIGH, indicates that the signal on PLLOUTGLOBALB/PLLOUTCOREB is
locked to the PLL source on PACKAGEPIN.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
104
EXTFEEDBACK: External feedback input to PLL. Enabled when the FEEDBACK_PATH parameter is set
to EXTERNAL.
DYNAMICDELAY: 4 bit input bus that enables dynamic control of the delay contributed by the Fine Delay
Adjust Block. The Fine Delay Adjust Block is used when there is a need to adjust the phase alignment of
PLLOUTGLOBAL/PLLOUTCORE with respect to REFERENCECLK. The DYNAMICDELAY port controls
are enabled when the DELAY_ADJUSTMENT_MODE parameter is set to DYNAMIC.
RESETB: Active low input that asynchronously resets the PLL.
BYPASS: Input signal, when asserted, connects the signal on REFERENCECLK to
PLLOUTCORE/PLLOUTGLOBAL pins.
LATCHINPUTVALUE: Active high input, when enabled, forces the PLL into low-power mode. The
PLLOUTGLOBALA/PLLOUTCOREA pins are held static at their last value only when the parameter
ENABLE_ICEGATE_PORTA is set to ‘1’, and the LATCHINPUTVALUE signal is asserted. The
PLLOUTGLOBALB/PLLOUTCOREB pins are held static at their last value only when the parameter
ENABLE_ICEGATE_PORTB is set to ‘1’, and the LATCHINPUTVALUE signal is asserted.
SCLK, SDI, SDO: These pins are used only for internal testing purposes, and need not be instantiated by
users.
Parameters
The SB_PLL40_2F_CORE primitive requires configuration through the specification of the following
parameters. It is strongly recommended that the configuration of the PLL primitives be accomplished
through the use of the PLL Configuration tool that is offered as part of the iCEcube2 software.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
105
Parameter Name
FEEDBACK_PATH
Description
Selects the feedback path
to the PLL
Parameter Value
SIMPLE
DELAY
PHASE_AND_DELAY
EXTERNAL
DELAY_ADJUSTMENT_MODE
_FEEDBACK
Selects the mode for the
Fine Delay Adjust block in
the feedback path
FIXED
DYNAMIC
FDA_FEEDBACK
Sets a constant value for
the Fine Delay Adjust
Block in the feedback path
DELAY_ADJUSTMENT_MODE
_RELATIVE
Selects the mode for the
Fine Delay Adjust block
0, 1,…,15
FIXED
DYNAMIC
FDA_RELATIVE
Sets a constant value for
the Fine Delay Adjust
Block
SHIFTREG_DIV_MODE
Selects shift register
configuration
PLLOUT_SELECT_PORTA
Selects the signal to be
output at the
PLLOUTCOREA and
PLLOUTGLOBALA ports
0, 1,…,15
0,1
SHIFTREG_0deg
SHIFTREG_90deg
GENCLK
GENCLK_HALF
ICE Technology Library
Lattice Semiconductor Corporation Confidential
Description
Feedback is internal to the PLL,
directly from VCO
Feedback is internal to the PLL,
through the Fine Delay Adjust
Block
Feedback is internal to the PLL,
through the Phase Shifter and
the Fine Delay Adjust Block
Feedback path is external to the
PLL, and connects to
EXTFEEDBACK pin. Also uses
the Fine Delay Adjust Block.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the
FDA_FEEDBACK parameter
setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[3:0] pins
The PLLOUTGLOBALA &
PLLOUTCOREA signals are
delay compensated by (n+1)*150
ps, where n = FDA_FEEDBACK
only if the setting of the
DELAY_ADJUSTMENT_MODE_
FEEDBACK is FIXED.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the FDA_RELATIVE
parameter setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[7:4] pins
The PLLOUTGLOBALA &
PLLOUTCOREA signals are
delayed w.r.t. the Port B signals,
by (n+1)*150 ps, where n =
FDA_RELATIVE. Used if
DELAY_ADJUSTMENT_MODE_
RELATIVE is “FIXED”.
Used when FEEDBACK_PATH
is “PHASE_AND_DELAY”.
0Divide by 4
1Divide by 7
o
0 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY”
o
90 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY” and
SHIFTREG_DIV_MODE=0
The internally generated PLL
frequency will be output to PortA.
No phase shift.
The internally generated PLL
frequency will be divided by 2
and then output to PORTA. No
phase shift.
106
PLLOUT_SELECT_PORTB
Selects the signal to be
output at the
PLLOUTCOREB and
PLLOUTGLOBALB ports
0 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY”
SHIFTREG_90deg
90 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY” and
SHIFTREG_DIV_MODE=0
The internally generated PLL
frequency will be output to PortB.
No phase shift.
The internally generated PLL
frequency will be divided by 2
and then output to PORTB. No
phase shift.
These parameters are used to
control the output frequency,
depending on the
FEEDBACK_PATH setting.
GENCLK
GENCLK_HALF
DIVR
DIVF
DIVQ
FILTER_RANGE
EXTERNAL_DIVIDE_FACTOR
ENABLE_ICEGATE_PORTA
ENABLE_ICEGATE_PORTB
REFERENCECLK divider
Feedback divider
VCO Divider
PLL Filter Range
Divide-by factor of a
divider in external
feedback path
Enables the PLL powerdown control
Enables the PLL powerdown control
ICE Technology Library
Lattice Semiconductor Corporation Confidential
o
SHIFTREG_0deg
0,1,2,…,15
0,1,..,63
1,2,…,6
0,1,…,7
User specified value.
Default 1
0
1
0
1
o
Specified only when there is a
user-implemented divider in the
external feedback path.
Power-down control disabled
Power-down controlled by
LATCHINPUTVALUE input
Power-down control disabled
Power-down controlled by
LATCHINPUTVALUE input
107
SB_PLL40_2F_PAD
The SB_PLL40_2F_PAD primitive should be used when the PLL is used to generate 2 different output
frequencies, and the source clock of the PLL is driven by an input pad located in the bottom IO bank (IO
Bank 2) or the top IO bank (IO Bank 0).
Port A
(Generated Clock)
Port B
(Generated Clock)
Ports
PACKAGEPIN: PLL REFERENCE CLOCK pin that serves as the input to the SB_PLL40_2F_PAD
primitive.
PLLOUTGLOBALA: Output clock generated by the PLL, drives a global clock network on the FPGA.
PLLOUTCOREA: Output clock generated by the PLL, drives regular FPGA routing. The frequency
generated on this output is the same as the frequency of the clock signal generated on the
PLLOUTLGOBALA port.
PLLOUTGLOBALB: Output clock generated by the PLL, drives a global clock network on the FPGA.
PLLOUTCOREB: Output clock generated by the PLL, drives regular FPGA routing. The frequency
generated on this output is the same as the frequency of the clock signal generated on the
PLLOUTLGOBALB port.
LOCK: Output port, when HIGH, indicates that the signal on PLLOUTGLOBALB/PLLOUTCOREB is
locked to the PLL source on PACKAGEPIN.
EXTFEEDBACK: External feedback input to PLL. Enabled when the FEEDBACK_PATH parameter is set
to EXTERNAL.
DYNAMICDELAY: 4 bit input bus that enables dynamic control of the delay contributed by the Fine Delay
Adjust Block. The Fine Delay Adjust Block is used when there is a need to adjust the phase alignment of
PLLOUTGLOBAL/PLLOUTCORE with respect to PACKAGEPIN. The DYNAMICDELAY port controls are
enabled when the DELAY_ADJUSTMENT_MODE parameter is set to DYNAMIC.
RESETB: Active low input that asynchronously resets the PLL.
BYPASS: Input signal, when asserted, connects the signal on PACKAGEPIN to
PLLOUTCORE/PLLOUTGLOBAL pins.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
108
LATCHINPUTVALUE: Active high input, when enabled, forces the PLL into low-power mode. The
PLLOUTGLOBALA/PLLOUTCOREA pins are held static at their last value only when the parameter
ENABLE_ICEGATE_PORTA is set to ‘1’, and the LATCHINPUTVALUE signal is asserted. The
PLLOUTGLOBALB/PLLOUTCOREB pins are held static at their last value only when the parameter
ENABLE_ICEGATE_PORTB is set to ‘1’, and the LATCHINPUTVALUE signal is asserted.
SCLK, SDI, SDO: These pins are used only for internal testing purposes, and need not be instantiated by
users.
Parameters
The SB_PLL40_2F_PAD primitive requires configuration through the specification of the following
parameters. It is strongly recommended that the configuration of the PLL primitives be accomplished
through the use of the PLL Configuration tool that is offered as part of the iCEcube2 software.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
109
Parameter Name
FEEDBACK_PATH
Description
Selects the feedback path
to the PLL
Parameter Value
SIMPLE
DELAY
PHASE_AND_DELAY
EXTERNAL
DELAY_ADJUSTMENT_MODE
_FEEDBACK
Selects the mode for the
Fine Delay Adjust block in
the feedback path
FIXED
DYNAMIC
FDA_FEEDBACK
Sets a constant value for
the Fine Delay Adjust
Block in the feedback path
DELAY_ADJUSTMENT_MODE
_RELATIVE
Selects the mode for the
Fine Delay Adjust block
0, 1,…,15
FIXED
DYNAMIC
FDA_RELATIVE
Sets a constant value for
the Fine Delay Adjust
Block
SHIFTREG_DIV_MODE
Selects shift register
configuration
PLLOUT_SELECT_PORTA
Selects the signal to be
output at the
PLLOUTCOREA and
PLLOUTGLOBALA ports
0, 1,…,15
0,1
SHIFTREG_0deg
SHIFTREG_90deg
GENCLK
GENCLK_HALF
ICE Technology Library
Lattice Semiconductor Corporation Confidential
Description
Feedback is internal to the PLL,
directly from VCO
Feedback is internal to the PLL,
through the Fine Delay Adjust
Block
Feedback is internal to the PLL,
through the Phase Shifter and the
Fine Delay Adjust Block
Feedback path is external to the
PLL, and connects to
EXTFEEDBACK pin. Also uses
the Fine Delay Adjust Block.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the FDA_FEEDBACK
parameter setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[3:0] pins
The PLLOUTGLOBALA &
PLLOUTCOREA signals are delay
compensated by (n+1)*150 ps,
where n = FDA_FEEDBACK only
if the setting of the
DELAY_ADJUSTMENT_MODE_F
EEDBACK is FIXED.
Delay of the Fine Delay Adjust
Block is fixed, the value is
specified by the FDA_RELATIVE
parameter setting
Delay of Fine Delay Adjust Block
is determined by the signal value
at the DYNAMICDELAY[7:4] pins
The PLLOUTGLOBALA &
PLLOUTCOREA signals are
delayed w.r.t. the Port B signals,
by (n+1)*150 ps, where n =
FDA_RELATIVE. Used if
DELAY_ADJUSTMENT_MODE_
RELATIVE is “FIXED”.
Used when FEEDBACK_PATH is
“PHASE_AND_DELAY”.
0Divide by 4
1Divide by 7
o
0 phase shift only if the setting of
FEEDBACK_PATH is
“PHASE_AND_DELAY”
o
90 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY” and
SHIFTREG_DIV_MODE=0
The internally generated PLL
frequency will be output to PortA.
No phase shift.
The internally generated PLL
frequency will be divided by 2 and
then output to PORTA. No phase
shift.
110
PLLOUT_SELECT_PORTB
Selects the signal to be
output at the
PLLOUTCOREB and
PLLOUTGLOBALB ports
0 phase shift only if the setting of
FEEDBACK_PATH is
“PHASE_AND_DELAY”
SHIFTREG_90deg
90 phase shift only if the setting
of FEEDBACK_PATH is
“PHASE_AND_DELAY” and
SHIFTREG_DIV_MODE=0
The internally generated PLL
frequency will be output to PortB.
No phase shift.
The internally generated PLL
frequency will be divided by 2 and
then output to PORTB. No phase
shift.
These parameters are used to
control the output frequency,
depending on the
FEEDBACK_PATH setting.
GENCLK
GENCLK_HALF
DIVR
DIVF
DIVQ
FILTER_RANGE
EXTERNAL_DIVIDE_FACTOR
ENABLE_ICEGATE_PORTA
ENABLE_ICEGATE_PORTB
REFERENCECLK divider
Feedback divider
VCO Divider
PLL Filter Range
Divide-by factor of a
divider in external
feedback path
Enables the PLL powerdown control
Enables the PLL powerdown control
ICE Technology Library
Lattice Semiconductor Corporation Confidential
o
SHIFTREG_0deg
0,1,2,…,15
0,1,..,63
1,2,…,6
0,1,…,7
User specified value.
Default 1
0
1
0
1
o
Specified only when there is a
user-implemented divider in the
external feedback path.
Power-down control disabled
Power-down controlled by
LATCHINPUTVALUE input
Power-down control disabled
Power-down controlled by
LATCHINPUTVALUE input
111
Hard Macro Primitives
iCE40LM Hard Macros
This section describes the following dedicated hard macro primitives available in iCE40LM devices.
SB_HSOSC (macro primitive for HSSG)
SB_LSOSC (macro primitive for LPSG)
SB_I2C
SB_SPI
SB_HSOSC (For HSSG)
SB_HSOSC primitive can be used to instantiate High Speed Strobe Generator (HSSG), which generates
12 MHz strobe signal. The strobe can drive either the global clock network or fabric routes directly based
on the clock network selection.
Ports
SB_HSOSC Ports
Signal Name
ENACLKM
CLKM
Direction
Input
Output
Description
Enable High Speed Strobe Generator. Active High.
Strobe Generator Output (12Mhz).
Clock Network Selection
By default the strobe generator use one of the dedicated clock networks in the device to drive the
elements. The user may configure the strobe generator to use the fabric routes instead of global clock
network using the synthesis attributes.
Synthesis Attribute
/* synthesis ROUTE_THROUGH_FABRIC=<value> */
Value:
0: Use dedicated clock network. Default option.
1: Use fabric routes.
Verilog Instantiation
SB_HSOSC OSCInst0 (
.ENACLKM(ENACLKM),
.CLKM(CLKM)
) /* synthesis ROUTE_THROUGH_FABRIC= [0|1] */;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
112
SB_LSOSC (For LPSG)
SB_LSOSC primitive can instantiate Low Power Strobe Generator (LPSG), which generates 10 KHz
strobe signal. The strobe can drive either the global clock network or fabric routes directly based on the
clock network selection.
Ports
SB_LSOSC Ports
Signal Name
ENACLKK
CLKK
Direction
Input
Output
Description
Enable Low Power Strobe Generator. Active High.
Strobe Generator Output (10Khz).
Clock Network Selection
By default the strobe generator use one of the dedicated clock networks in the device to drive the
elements. The user may configure the strobe generator to use the fabric routes instead of global clock
network using the synthesis attribute.
Synthesis Attribute:
/* synthesis ROUTE_THROUGH_FABRIC=<value> */
Value:
0: Use dedicated clock network. Default option.
1: Use fabric routes.
Verilog Instantiation
SB_LSOSC OSCInst0 (
.ENACLKK(ENACLKK),
.CLKK(CLKK)
) /* synthesis ROUTE_THROUGH_FABRIC= [0|1] */;
SB_I2C
The I2C hard IP provides industry standard two pin communication interface that conforms to V2.1 of the
I2C bus specification. It could be configured as either master or slave port. In master mode, it support
configurable data transfer rate and perform arbitration detection to allow it to operate in multi-master
systems. It supports both 7 bits and 10 bits addressing in slave mode with configurable slave address and
clock stretching in both master and slave mode with enable/disable capability.
iCE40LM device supports two I2C hard IP primitives , located at upper left corner and upper right corner
of the chip.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
113
Ports
SB_I2C Ports
Signal Name
SBCLKI
SBRWI
SBSTBI
SBADRI0
SBADRI1
SBADRI2
SBADRI3
SBADRI4
SBADRI5
SBADRI6
SBADRI7
SBDATI0
SBDATI1
SBDATI2
SBDATI3
SBDATI4
SBDATI5
SBDATI6
SBDATI7
SBDATO0
SBDATO1
SBDATO2
SBDATO3
SBDATO4
SBDATO5
SBDATO6
SBDATO7
Direction
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Output
Output
Output
Output
Output
Output
Output
Output
Description
System Clock input.
System Read/Write Input.
Strobe Signal
System Bus Control registers address. Bit 0.
System Bus Control registers address. Bit 1.
System Bus Control registers address. Bit 2.
System Bus Control registers address. Bit 3.
System Bus Control registers address. Bit 4.
System Bus Control registers address. Bit 5.
System Bus Control registers address. Bit 6.
System Bus Control registers address. Bit 7.
System Data Input. Bit 0.
System Data input. Bit 1.
System Data input. Bit 2.
System Data input. Bit 3.
System Data input. Bit 4.
System Data input. Bit 5.
System Data input. Bit 6.
System Data input. Bit 7.
System Data Output. Bit 0.
System Data Output. Bit 1.
System Data Output. Bit 2.
System Data Output. Bit 3.
System Data Output. Bit 4.
System Data Output. Bit 5.
System Data Output. Bit 6.
System Data Output. Bit 7.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
114
SBACKO
I2CIRQ
I2CWKUP
SCLI
SCLO
SCLOE
SDAI
SDAO
SDAOE
Output
Output
Output
Input
Output
Output
Input
Output
Output
System Acknowledgement.
I2C Interrupt output.
I2C Wake Up from Standby signal.
Serial Clock Input.
Serial Clock Output
Serial Clock Output Enable. Active High.
Serial Data Input
Serial Data Output
Serial Data Output Enable. Active High.
Parameters
I2C Primitive requires configuring certain parameters for slave initial address and selecting I2C IP
location.
I2C Location
Parameters
Parameter Default
Value.
Description.
Upper Left Corner
I2C_SLAVE_INIT_ADDR
0b1111100001
BUS_ADDR74
0b0001
I2C_SLAVE_INIT_ADDR
0b1111100010
BUS_ADDR74
0b0011
Upper Bits <9:2> can
be changed through
control registers.
Lower bits <1:0> are
fixed.
Fixed value. SBADRI
[7:4] bits also should
match with this value
to activate the IP.
Upper Bits <9:2> can
be changed through
control registers.
Lower bits <1:0> are
fixed.
Fixed value. SBADRI
[7:4] bits also should
match with this value
to activate the IP.
Upper Right Corner
Synthesis Attribute
Synthesis attribute “I2C_CLK_DIVIDER” is used by PNR and STA tools for optimization and deriving the
appropriate clock frequency at SCLO output with respect to the SBCLKI input clock frequency.
/* synthesis I2C_CLK_DIVIDER=[Divide Range] */
Divide Range
: 0, 1, 2, 3 … 1023. Default is 0.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
115
Verilog Instantiation
SB_I2C i2cInst0 (
.SBCLKI(sbclki),
.SBRWI(sbrwi),
.SBSTBI(sbstbi),
.SBADRI7(sbadri[7]),
.SBADRI6(sbadri[6]),
.SBADRI5(sbadri[5]),
.SBADRI4(sbadri[4]),
.SBADRI3(sbadri[3]),
.SBADRI2(sbadri[2]),
.SBADRI1(sbadri[1]),
.SBADRI0(sbadri[0]),
.SBDATI7(sbdati[7]),
.SBDATI6(sbdati[6]),
.SBDATI5(sbdati[5]),
.SBDATI4(sbdati[4]),
.SBDATI3(sbdati[3]),
.SBDATI2(sbdati[2]),
.SBDATI1(sbdati[1]),
.SBDATI0(sbdati[0]),
.SCLI(scli),
.SDAI(sdai),
.SBDATO7(sbdato[7]),
.SBDATO6(sbdato[6]),
.SBDATO5(sbdato[5]),
.SBDATO4(sbdato[4]),
.SBDATO3(sbdato[3]),
.SBDATO2(sbdato[2]),
.SBDATO1(sbdato[1]),
.SBDATO0(sbdato[0]),
.SBACKO(sbacko),
.I2CIRQ(i2cirq),
.I2CWKUP(i2cwkup),
.SCLO(sclo),
.SCLOE(scloe),
.SDAO(sdao),
.SDAOE(sdaoe)
)/* synthesis I2C_CLK_DIVIDER= 1 */;
defparam i2cInst0.I2C_SLAVE_INIT_ADDR = "0b1111100001";
defparam i2cInst0.BUS_ADDR74 = "0b0001";
SB_SPI
The SPI hard IP provide industry standard four-pin communication interface with 8 bit wide System Bus to
communicate with System Host. It could be configured as Master or Slave SPI port with separate Chip
Select Pin. In master mode, it provides programmable baud rate, and supports CS HOLD capability for
multiple transfers. It provides variety status flags, such as Mode Fault Error flag, Transmit/Receive status
flag etc. for easy communicate with system host.
iCE40LM device supports two SPI hard IP primitives, located at lower left corner and lower right corner of
the chip.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
116
Ports
SB_SPI Ports
Signal Name
SBCLKI
SBRWI
SBSTBI
SBADRI0
SBADRI1
SBADRI2
SBADRI3
SBADRI4
SBADRI5
SBADRI6
SBADRI7
SBDATI0
SBDATI1
SBDATI2
SBDATI3
SBDATI4
SBDATI5
SBDATI6
SBDATI7
SBDATO0
SBDATO1
SBDATO2
SBDATO3
SBDATO4
SBDATO5
SBDATO6
Direction
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Description
System Clock input.
System Read/Write Input.
Strobe Signal
System Bus Control registers address. Bit 0.
System Bus Control registers address. Bit 1.
System Bus Control registers address. Bit 2.
System Bus Control registers address. Bit 3.
System Bus Control registers address. Bit 4.
System Bus Control registers address. Bit 5.
System Bus Control registers address. Bit 6.
System Bus Control registers address. Bit 7.
System Data Input. Bit 0.
System Data input. Bit 1.
System Data input. Bit 2.
System Data input. Bit 3.
System Data input. Bit 4.
System Data input. Bit 5.
System Data input. Bit 6.
System Data input. Bit 7.
System Data Output. Bit 0.
System Data Output. Bit 1.
System Data Output. Bit 2.
System Data Output. Bit 3.
System Data Output. Bit 4.
System Data Output. Bit 5.
System Data Output. Bit 6.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
117
SBDATO7
SBACKO
SPIIRQ
SPIWKUP
MI
SO
SOE
SI
MO
MOE
SCKI
SCKO
SCKOE
SCSNI
MCSNO0
MCSNO1
MCSNO2
MCSNO3
MCSNOE0
Input
Output
Output
Output
Input
Output
Output
Input
Output
Output
Input
Output
Output
Input
Output
Output
Output
Output
Output
MCSNOE1
Output
MCSNOE2
Output
MCSNOE3
Output
System Data Output. Bit 7.
System Acknowledgement
SPI Interrupt output.
SPI Wake Up from Standby signal.
Master Input from PAD
Slave Output to PAD
Slave Output Enable to PAD. Active High.
Slave Input from PAD
Master Output to PAD
Master Output Enable to PAD. Active High
Slave Clock Input From PAD
Slave Clock Output to PAD
Slave Clock Output Enable to PAD. Active High.
Slave Chip Select Input From PAD
Master Chip Select Output to PAD. Line 0.
Master Chip Select Output to PAD. Line 1.
Master Chip Select Output to PAD. Line 2.
Master Chip Select Output to PAD. Line 3.
Master Chip Select Output Enable to PAD. Active High.
Line 0.
Master Chip Select Output Enable to PAD. Active High.
Line 1
Master Chip Select Output Enable to PAD. Active High.
Line 2
Master Chip Select Output Enable to PAD. Active High.
Line 3
Parameters
SPI Primitive requires configuring a parameter for selecting the SPI IP location.
I2C Location
Parameters
Parameter Default
Value.
Description.
BUS_ADDR74
0b0000
BUS_ADDR74
0b0001
Fixed value. SBADRI
[7:4] bits also should
match with this value
to activate the IP.
Fixed value. SBADRI
[7:4] bits also should
match with this value
to activate the IP.
Lower Left Corner
Lower Right Corner
Synthesis Attribute
Synthesis attribute “SPI_CLK_DIVIDER” is used by PNR and STA tools for optimization and deriving the
appropriate clock frequency at SCKO output with respect to the SBCLKI input clock frequency.
/* synthesis SPI_CLK_DIVIDER= [Divide Range] */
Divide Range
: 0, 1, 2, 3….63. Default is 0.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
118
Verilog Instantiation
SB_SPI spiInst0 (
.SBCLKI(sbclki),
.SBRWI(sbrwi),
.SBSTBI(sbstbi),
.SBADRI7(sbadri[7]),
.SBADRI6(sbadri[6]),
.SBADRI5(sbadri[5]),
.SBADRI4(sbadri[4]),
.SBADRI3(sbadri[3]),
.SBADRI2(sbadri[2]),
.SBADRI1(sbadri[1]),
.SBADRI0(sbadri[0]),
.SBDATI7(sbdati[7]),
.SBDATI6(sbdati[6]),
.SBDATI5(sbdati[5]),
.SBDATI4(sbdati[4]),
.SBDATI3(sbdati[3]),
.SBDATI2(sbdati[2]),
.SBDATI1(sbdati[1]),
.SBDATI0(sbdati[0]),
.MI(mi),
.SI(si),
.SCKI(scki),
.SCSNI(scsni),
.SBDATO7(sbdato[7]),
.SBDATO6(sbdato[6]),
.SBDATO5(sbdato[5]),
.SBDATO4(sbdato[4]),
.SBDATO3(sbdato[3]),
.SBDATO2(sbdato[2]),
.SBDATO1(sbdato[1]),
.SBDATO0(sbdato[0]),
.SBACKO(sbacko),
.SPIIRQ(spiirq),
.SPIWKUP(spiwkup),
.SO(so),
.SOE(soe),
.MO(mo),
.MOE(moe),
.SCKO(scko),
.SCKOE(sckoe),
.MCSNO3(mcsno_hi[3]),
.MCSNO2(mcsno_hi[2]),
.MCSNO1(mcsno_lo[1]),
.MCSNO0(mcsno_lo[0]),
.MCSNOE3(mcsnoe_hi[3]),
.MCSNOE2(mcsnoe_hi[2]),
.MCSNOE1(mcsnoe_lo[1]),
.MCSNOE0(mcsnoe_lo[0])
) /* synthesis SPI_CLK_DIVIDER = "1" */;
defparam spiInst0.BUS_ADDR74 = "0b0000";
ICE Technology Library
Lattice Semiconductor Corporation Confidential
119
iCE5LP (iCE40 Ultra) Hard Macros
This section describes the following dedicated hard macro primitives available in iCE5LP (iCE40 Ultra)
devices.
SB_HFOSC
SB_LFOSC
SB_LED_DRV_CUR
SB_RGB_DRV
SB_IR_DRV
SB_IO_OD
SB_I2C
SB_SPI
SB_MAC16
SB_HFOSC
SB_HFOSC primitive generates 48MHz nominal clock frequency within +/- 10% variation, with user
programmable divider value of 1, 2, 4, and 8. The HFOSC can drive either the global clock network or
fabric routes directly based on the clock network selection.
Ports
SB_HFOSC Ports
Signal Name
Direction
CLKHFPU
Input
CLKHFEN
Input
CLKHF
Output
Description
Power up the HFOSC circuit. After power up, oscillator
output will be stable after 100us. Active High.
Enable the clock output. Enable should be low for the
100us power up period. Active High.
HF Oscillator output.
Parameters
Parameter
Parameter Values.
CLKHF_DIV
"0b00"
"0b01"
"0b10"
"0b11"
Description.
Sets 48MHz HFOSC output.
Sets 24MHz HFOSC output.
Sets 12MHz HFOSC output.
Sets 6MHz HFOSC output
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input CLKHFEN: Logic “0”
Input CLKHFPU: Logic “0”
ICE Technology Library
Lattice Semiconductor Corporation Confidential
120
Clock Network Selection
By default the oscillator use one of the dedicated clock networks in the device to drive the elements. The
user may configure the oscillator to use the fabric routes instead of global clock network using the
synthesis attribute.
Synthesis Attributes
/* synthesis ROUTE_THROUGH_FABRIC = <value> */
Value:
0: Use dedicated clock network. Default option.
1: Use fabric routes.
Verilog Instantiation
SB_HFOSC OSCInst0 (
.CLKHFEN(ENCLKHF),
.CLKHFPU(CLKHF_POWERUP),
.CLKHF(CLKHF)
) /* synthesis ROUTE_THROUGH_FABRIC= [0|1] */;
defparam OSCInst0.CLKHF_DIV = "0b00";
SB_LFOSC
SB_LFOSC primitive generates 10 KHz nominal clock frequency within +/- 10% variation. There is no
divider on the LFOSC.
The LFOSC can drive either the global clock network or fabric routes directly based on the clock network
selection
Ports
SB_LFOSC Ports
Signal Name
Direction
CLKLFPU
Input
CLKLFEN
Input
CLKLF
Output
Description
Power up the LFOSC circuit. After power up, oscillator
output will be stable after 100us. Active High.
Enable the clock output. Enable should be low for the
100us power up period. Active High.
LF Oscillator output.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input CLKLFEN: Logic “0”
Input CLKLFPU: Logic “0”
ICE Technology Library
Lattice Semiconductor Corporation Confidential
121
Clock Network Selection
By default the oscillator use one of the dedicated clock networks in the device to drive the elements. The
user may configure the oscillator to use the fabric routes instead of global clock network using the
synthesis attribute.
Synthesis Attributes
/* synthesis ROUTE_THROUGH_FABRIC = <value> */
Value:
0: Use dedicated clock network. Default option.
1: Use fabric routes.
Verilog Instantiation
SB_LFOSC OSCInst1 (
.CLKLFEN(ENCLKLF),
.CLKLFPU(CLKLF_POWERUP),
.CLKLF(CLKLF)
) /* synthesis ROUTE_THROUGH_FABRIC= [0|1] */;
SB_LED_DRV_CUR
SB_LED_DRV_CUR primitive generates the constant reference current required to power up the
SB_RGB_DRV and SB_IR_DRV primitives.
Ports
Signal Name
EN
LEDPU
SB_LED_DRV_CUR Ports
Direction
Input
Output
Description
Enable to generate constant current source for
SB_RGB_DRV and SB_IR_DRV primitives. After Enable,
reference current value will be stable after 100us. Active
High.
Power up signal for SB_RGB_DRV and SB_IR_DRV
primitives. This port should be connected only to
RGBPU/IRPU pins of SB_RGB_DRV and SB_IR_DRV
primitives.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input EN
: Logic “0”
ICE Technology Library
Lattice Semiconductor Corporation Confidential
122
Verilog Instantiation
SB_LED_DRV_CUR
LED_CUR_inst
(
.EN(enable_led_current),
.LEDPU(led_power_up)
);
SB_RGB_DRV
SB_RGB_DRV primitive contains 3 dedicated open drain I/O pins for RGB LED outputs. Each of the RGB
LED output is bonded out together with an SB_IO_OD primitive to the package pin. User can either use
SB_RGB_DRV primitive or the SB_IO_OD primitive to drive the package pin, but not both.
The primitive allows configuration of each of the 3 RGB LED outputs individually. When the
RGBx_CURRENT parameter of RGBx output is set to "0b000000", then SB_IO_OD can be used to drive
the package pin.
Ports
SB_RGB_DRV Ports
Signal Name
Direction
RGBLEDEN
RGBPU
Input
Input
RGB0PWM
Input
RGB1PWM
Input
RGB2PWM
Input
RGB0
RGB1
RGB2
Output
Output
Output
Description
Enable the SB_RGB_DRV primitive. Active High.
Power Up Signal. Connect to LEDPU port of
SB_LED_DRV_CUR primitive.
Input data to drive RGB0 LED pin. This input is usually
driven from the SB_LEDD_IP.
Input data to drive RGB1 LED pin. This input is usually
driven from the SB_LEDD_IP.
Input data to drive RGB2 LED pin. This input is usually
driven from the SB_LEDD_IP.
RGB0 LED output.
RGB1 LED output.
RGB2 LED output.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input RGBLEDEN
: Logic “0”
Input RGB0PWM
: Logic “0”
Input RGB1PWM
: Logic “0”
ICE Technology Library
Lattice Semiconductor Corporation Confidential
123
Input RGB2PWM
Input RGBPU
: Logic “0”
: Logic “0”
Parameters
The SB_RGB_DRV primitive contains the following parameter and their default values:
Parameter RGB0_CURRENT = "0b000000";
Parameter RGB1_CURRENT = "0b000000";
Parameter RGB2_CURRENT = "0b000000";
Parameter values:
"0b000000" = 0mA. // Set this value to use the associated SB_IO_OD instance at RGB
// LED location.
"0b000001" = 4mA.
"0b000011" = 8mA.
"0b000111" = 12mA.
"0b001111" = 16mA.
"0b011111" = 20mA.
"0b111111" = 24mA.
Verilog Instantiation
SB_RGB_DRV RGB_DRIVER (
.RGBLEDEN(ENABLE_LED),
.RGB0PWM(RGB0),
.RGB1PWM(RGB1),
.RGB2PWM(RGB2),
.RGBPU(led_power_up),
.RGB0(LED0),
.RGB1(LED1),
.RGB2(LED2)
);
defparam RGB_DRIVER.RGB0_CURRENT = "0b111111";
defparam RGB_DRIVER.RGB1_CURRENT = "0b111111" ;
defparam RGB_DRIVER.RGB2_CURRENT = "0b111111";
SB_IR_DRV
SB_IR_DRV primitive contains a single dedicated open drain I/O pin for IRLED output. The IRLED output
is bonded out together with an SB_IO_OD primitive to the package pin. User can either use SB_IR_DRV
primitive or the SB_IO_OD primitive to drive the package pin, but not both.
When the IR_CURRENT parameter is set to "0b0000000000", then SB_IO_OD can be used to drive the
package pin.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
124
Ports
SB_IR_DRV Ports
Signal Name
IRLEDEN
IRPU
IRPWM
IRLED
Direction
Input
Input
Input
Output
Description
Enable the SB_IR_DRV primitive. Active High.
Power Up Signal. Connect to LEDPU port of
SB_LED_DRV_CUR primitive.
PWM Input data to drive IRLED pin.
IR LED output.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input IRLEDEN
: Logic “0”
Input IRPWM
: Logic “0”
Parameter
The SB_IR_DRV primitive contains the following parameter and their default values:
Parameter IR_CURRENT = "0b0000000000";
Parameter Values:
"0b0000000000"; = 0mA. // Set this value to use the associated SB_IO_OD instance at
// IR LED location.
"0b0000000001"; = 50mA
"0b0000000011"; = 100mA
"0b0000000111"; = 150mA
"0b0000001111"; = 200mA
"0b0000011111"; = 250mA
"0b0000111111"; = 300mA
"0b0001111111"; = 350mA
"0b0011111111"; = 400mA
"0b0111111111"; = 450mA
"0b1111111111"; = 500mA
Verilog Instantiation
SB_IR_DRV
IRDRVinst (
.IRLEDEN(ENABLE_IRLED),
.IRPWM(IR_INPUT),
.IRPU(led_power_up),
.IRLED(IR_LED)
);
defparam IRDRVinst.IR_CURRENT = "0b1111111111";
ICE Technology Library
Lattice Semiconductor Corporation Confidential
125
SB_RGB_IP
SB_RGB_IP primitive generates the 3 RGB PWM outputs, to be connected to the LED drivers.
Ports
Signal Name
CLK
RST
PARAMSOK
RGBCOLOR[3:0]
BRIGHTNESS[3:0]
BREATHRAMP[3:0]
BLINKRATE[3:0]
REDPWM
GREENPWM
BLUEPWM
SB_RGB_IP Ports
Direction
Input
Input
Input
Input
Input
Input
Input
Output
Output
Output
Description
Clock Input.
Asynchronous Reset Input.
Enable signal to sample the rgb data.
4 bit rgb color data input
4 bit rgb brightness data input
4 bit breathramp data input
4 bit blinkrate data input
RED PWM output.
GREEN PWM output.
BLUE PWM output.
Default Signal Values
The iCEcube2 software assigns the logic “0” value to all unconnected input ports.
Verilog Instantiation
SB_RGB_IP RGBPWMIP_inst(
.CLK (CLK),
.RST (RST),
.PARAMSOK (PARAMSOK),
.RGBCOLOR (RGBCOLOR),
.BRIGHTNESS (BRIGHTNESS),
.BREATHRAMP (BREATHRAMP),
.BLINKRATE (BLINKRATE),
.REDPWM (REDPWM),
.GREENPWM (GREENPWM),
.BLUEPWM (BLUEPWM)
);
// Async rst
ICE Technology Library
Lattice Semiconductor Corporation Confidential
126
SB_IO_OD
The SB_IO_OD is the open drain IO primitive. When the Tristate output is enabled, the IO pulls down the
package pin signal to zero. The following figure and Verilog template illustrate the complete user
accessible logic diagram, and its Verilog instantiation.
Ports
SB_IO_OD Ports
Signal Name
PACKAGEPIN
LATCHINPUTVALUE
CLOCKENABLE
INPUTCLK
OUTPUTCLK
OUTPUTENABLE
DOUT0
DOUT1
DIN0
DIN1
Direction
Bidirectional
Input
Input
Input
Input
Input
Input
Input
Output
Output
Description
Bidirectional IO pin.
Latches/Holds the input data.
Clock enable signal.
Clock for the input registers.
Clock for the output registers.
Enable Tristate output. Active high.
Data to package pin.
Data to package pin.
Data from package pin.
Data from package pin.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
127
Default Signal Values
The iCEcube2 software assigns the logic “0” value to all unconnected input ports except for
CLOCKENABLE.
Note that explicitly connecting logic “1” value to port CLOCKENABLE will result in a non-optimal
implementation, since extra LUT will be used to generate the Logic “1”. If the user’s intention is to keep
the Input and Output registers always enabled, it is recommended that port CLOCKENABLE to be left
unconnected.
Parameter Values
Parameter PIN_TYPE = 6’b000000;
// See Input and Output Pin Function Tables in SB_IO.
// Default value of PIN_TYPE = 6’b000000
Parameter NEG_TRIGGER = 1’b0;
// Specify the polarity of all FFs in the I/O to be falling edge when
NEG_TRIGGER = 1.
Default is 1’b0, rising edge.
Input and Output Pin Function Tables
Refer SB_IO Input and Output Pin Functional Table for the PIN_TYPE settings. Some of the
output pin configurations are not applicable for SB_IO_OD primitive.
Verilog Instantiation
SB_IO_OD
OpenDrainInst0
(
.PACKAGEPIN (PackagePin),
.LATCHINPUTVALUE (latchinputvalue),
.CLOCKENABLE (clockenable),
.INPUTCLK (inputclk),
.OUTPUTCLK (outputclk),
.OUTPUTENABLE (outputenable),
.DOUT0 (dout0),
.DOUT1 (dout1),
.DIN0 (din0),
.DIN1 (din1)
// User’s Pin signal name
// Latches/holds the Input value
// Clock Enable common to input and
// output clock
// Clock for the input registers
// Clock for the output registers
// Output Pin Tristate/Enable
// control
// Data 0 – out to Pin/Rising clk
// edge
// Data 1 - out to Pin/Falling clk
// edge
// Data 0 - Pin input/Rising clk
// edge
// Data 1 – Pin input/Falling clk
// edge
);
defparam OpenDrainInst0.PIN_TYPE = 6'b000000;
defparam OpenDrainInst0.NEG_TRIGGER = 1'b0;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
128
SB_I2C
iCE5LP device supports two I2C hard IP primitives , located at upper left corner and upper right corner
of the chip.
Ports
The port interface is similar as iCE40LM SB_I2C primitive. Refer Page 113.
Parameters
The parameters are same as ICE40LM SB_I2C primitive.
Synthesis Attribute
I2C_CLK_DIVIDER
Synthesis attribute “I2C_CLK_DIVIDER” is used by PNR and STA tools for optimization and deriving the
appropriate clock frequency at SCLO output with respect to the SBCLKI input clock frequency.
/* synthesis I2C_CLK_DIVIDER= Divide Value */
Divide Value: 0, 1, 2, 3 … 1023. Default is 0.
SDA_INPUT_DELAYED
SDA_INPUT_DELAYED attribute is used to add 50ns additional delay to the SDAI signal.
/* synthesis SDA_INPUT_DELAYED= value */
Value:
ICE Technology Library
Lattice Semiconductor Corporation Confidential
129
0: No delay.
1: Add 50ns delay. (Default value).
SDA_OUTPUT_DELAYED
SDA_OUTPUT_DELAYED attribute is used to add 50ns additional delay to the SDAO signal.
/* synthesis SDA_OUTPUT_DELAYED= value */
Value:
0: No delay (Default value).
1: Add 50ns delay.
SB_SPI
iCE5LP device supports two SPI hard IP primitives, located at lower left corner and lower right corner of
the chip. The port interface of SB_SPI is similar as ICE40LM SB_SPI primitive. Refer Page 116.
Ports
The port interface is similar as iCE40LM SB_SPI primitive. Refer Page 116.
Parameters
The parameters are same as ICE40LM SB_SPI primitive.
Synthesis Attribute
The synthesis attribute is same as ICE40LM SB_SPI primitive.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
130
SB_MAC16
The SB_MAC16 primitive is the dedicated configurable DSP block available in iCE5LP devices. The
SB_MAC16 can be configured into a multiplier, adder, subtracter, accumulator, multiply-add and multiplysub through the instance parameters. The SB_MAC16 blocks can be cascaded to implement wider
functional units.
iCEcube2 supports a set of predefined SB_MAC16 functional configurations. Refer Page 137 for the list
of supported configurations.
SB_MAC16 Interface Diagram
ICE Technology Library
Lattice Semiconductor Corporation Confidential
131
Input Registers
ACCUMCO
SIGNEXTOUT
CO
Accumulator
0
1
Multiplier
Q[31:16]
1
1
16x16 Pipeline
Registers
Q
0
1
D
B[15:8]
HLD
C1
R
8x8
Q
D
B[15:8]
Q
HLD
8x8
C22
D
B[7:0]
J
+
Q
C11
[7:0]
+
A[7:0]
P[23:16]
16x16=32
L
[15:0]
B[15:0]
BHOLD
D
Q
1
8x8
HLD
C2
R
Q
R
D
Q
H
R
[31:16]
[15:0]
0
1
1
C7
Q[15:0
[7:0]
1
0
D
B[7:0]
0
HLD
K
G
+
P[15:8]
Y
0
[15:8]
1
ADDSUBBOT
0
1
[15:0]
[7:0]
0
C10
16x16
Pipeline
Register
[15:0]
C6
R
ORSTTOP
OHOLDTOP
OLOADTOP
HCI
P[31:24]
[15:8]
HLD
8x8
Hi
C9
C8
3
1
0
O[31:16]
2
[7:0]
8x8 PowerSave
A[15:8]
3
1
[15:8]
IRSTTOP
2
R
0
8x8=16
C6
R
1
HLD
[15:0]
1
0
A[7:0]
Q
X[15]
F
C4
R
0
D
1
C5
C14
D
A[15:8]
P
C13
A
0
0
1
1
[15:0]
0
1
+
3
C0
R
A[15:0]
AHOLD
X
C12
2
Q
HLD
Q
0
1
D
ADDSUBTOP
0
1
0
C[15:0]
CHOLD
W
0
C
0
P[7:0]
C19
Z
R
0
1
+
0
1
8x8=16
B
S
D
Q
0
1
HLD
2
R
3
O[15:0]
C16
C15
1
ORSTBOT
OHOLDBOT
OLOADBOT
2
3
D
0
D
Q
LCI
C18
C17
1
HLD
C3
1
C20
0
3
BSGND =C24
2
C21
ASGND =C23
1
R
0
D[15:0]
DHOLD
Lo
Z[15]
0
IRSTBOT
CLK
CE
SIGNEXTIN
ACCUMCI
CI
SB_MAC16 Functional Model
Ports
Signal
Name
SB_MAC16 Ports
Description
Direction
CLK
CE
C[15:0]
A[15:0]
Input
Input
Input
Input
B[15:0]
Input
D[15:0]
AHOLD
Input
Input
Default
Values
Clock input. Applies to all clocked elements in the MAC16 Block.
Clock Enable Input. Active High.
Input to the C Register / Direct input to the adder accumulator.
Input to the A Register / Direct input to the multiplier blocks /Direct input to
the adder accumulator.
Input to the B Register / Direct input to the multiplier blocks /Direct input to
the adder accumulator.
Input to the D Register / Direct input to the adder accumulator.
Hold A registers Data .Controls data flow into the input register A. Active
High.
0
Update (load) register at next active clock edge.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
132
1’b1
16’b0
16’b0
16’b0
16’b0
1’b0
BHOLD
CHOLD
DHOLD
Input
Input
Input
1 Hold (retain) current register value, regardless of clock.
Hold B registers Data .Controls data flow into the B input register. Active
High.
1’b0
0 Update (load) register at next active clock edge.
1 Hold (retain) current register value, regardless of clock.
Hold C registers Data. Controls data flow into the A input register. Active
High.
1’b0
0 Update (load) register at next active clock edge.
1 Hold (retain) current register value, regardless of clock.
Hold D registers Data. Controls data flow into the A input register. Active
High.
1’b0
0 Update (load) register at next active clock edge.
1 Hold (retain) current register value, regardless of clock.
Reset input to the A and C input registers, and the pipeline registers in
the upper half of the multiplier block. Active High
1’b0
IRSTTOP
Input
IRSTBOT
Input
Reset input to the B and C input registers, and the pipeline registers in
the lower half of the multiplier block, and the 32-bit multiplier result
pipeline register. Active High.
1’b0
ORSTTOP
Input
Reset the high-order bits of the accumulator register ([31:16]). Active
High.
1’b0
ORSTBOT
Input
Reset the low-order accumulator register bits ([15:0]). Active High.
1’b0
OLOADTOP
Input
High-order Accumulator Register Accumulate/Load. Controls whether the
accumulator register accepts the output of the adder/subtracter or
whether the register is loaded with the value from Input C (or Register C,
if configured).
1’b0
0
OLOADBOT
Input
Accumulator Register [31:16] loaded with output from
adder/subtracter.
1 Accumulator Register [31:16] loaded with Input C or Register C,
depending on primitive parameter value.
Low-order Accumulator Register Accumulate/Load. Controls whether the
low-order accumulator register bits (15:0] accepts the output of the
adder/subtracter or whether the register is loaded with the value from
Input D (or Register D, if configured).
0
ADDSUBTOP
ADDSUBBOT
Input
input
Accumulator Register [15:0] loaded with output from
adder/subtracter.
1 Accumulator Register [15:0] loaded with Input D or Register D,
depending on primitive parameter value.
High-order Add/Subtract. Controls whether the adder/subtracter adds or
subtracts.
1’b0
0 Add: W+X+HCI
1 Subtract: W-X-HCI
Low-order Add/Subtract. Controls whether the adder/subtracter adds or
subtracts.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
1’b0: Add
1’b0: Add
133
OHOLDTOP
Input
OHOLDBOT
Input
0 Add: Y+Z+LCI
1 Subtract: Y-Z-LCI
High-order Accumulator Register Hold. Controls data flow into the highorder ([31:16]) bits of the accumulator.
0 Update (load) register at next active clock edge.
1 Hold (retain) current register value, regardless of clock.
Low-order Accumulator Register Hold. Controls data flow into the highorder ([15:0]) bits of the accumulator.
CI
Input
0 Update (load) register at next active clock edge.
1 Hold (retain) current register value, regardless of clock.
Carry/borrow input from lower logic tile.
ACCUMCI
Input
Cascade Carry/borrow input from lower MAC16 block.
SIGNEXTIN
O[31:0]
Input
Output
Sign extension input from lower MAC16 block.
32 bit MAC16 Output.
O[31:0]
CO
Output
ACCUMCO
SIGNEXTOUT
Output
Output
32-bit result of a 16x16 multiply operation or a 32-bit
adder/accumulate function.
O[31:16] 16-bit result of an 8x8 multiply operation or a 32-bit
adder/accumulate function.
O[15:0] 16-bit result of an 8x8 multiply operation or a 32-bit
adder/accumulate function.
Carry/borrow output to higher logic tile.
Cascade Carry/borrow output to higher MAC16 block.
Sign extension output to higher MAC16 block.
Parameters
The parameter table below shows the list of parameters to configure the SB_MAC16 block. This table
also maps the parameter to the configuration bits shown in the SB_MAC16 Functional diagram.
Parameter Name
NEG_TRIGGER
Configuration Parameter
bits
Description
Controls input clock
polarity
C_REG
C0
A_REG
C1
B_REG
C2
D_REG
C3
TOP_8x8_MULT_REG
C4
BOT_8x8_MULT_REG
C5
Parameter Description
Values
0
All the registers are
rising_edge triggered.
1
All the registers are
falling_edge triggered.
Input C register
0
Input C not registered
Control.
1
Input C registered
Input A register
0
Input A not registered
Control
1
Input A registered
Input B register
0
Input B not registered
Control
1
Input B registered
Input D register
0
Input D not registered
Control
1
Input D registered
Top 8x8 multiplier
0
Top 8x8 multiplier output is
output register
not registered.
control (point F)
1
Top 8x8 multiplier output is
registered.
0
Bottom 8x8 multiplier
Bottom 8x8 multiplier
ICE Technology Library
Lattice Semiconductor Corporation Confidential
134
output register
control. (point G)
PIPELINE_16x16_MULT_REG1
PIPELINE_16x16_MULT_REG2
TOPOUTPUT_SELECT
C6
C7
C9,C8
1
Intermediate 8x8
multiplier pipeline
register controls
(points J and K).
These multipliers are
only used for 16x16
multiply operations.
For 8x8 multiply
operations, set C6
and C7 to 1, which
reduces power
consumption.
16x16 multiplier
Pipeline registers
control. (point H)
0
Selects Top
SB_MAC16 output
O[31:16].
00
1
0
1
01
10
11
TOPADDSUB_LOWERINPUT
C11,C10
Selects input X for
the upper
adder/subtracter
00
01
10
11
TOPADDSUB_UPPERINPUT
TOPADDSUB_CARRYSELECT
C12
C14,C13
Selects input W for
the upper
adder/subtracter
0
Carry/borrow input
select to upper
adder/subtracter.
00
01
10
1
11
BOTOUTPUT_SELECT
C16,C15
Selects Lower
SB_MAC16 output
O[15:0].
00
01
10
ICE Technology Library
Lattice Semiconductor Corporation Confidential
output is not registered.
Bottom 8x8 multiplier
output is registered
Intermediate 8x8 multiplier
outputs are not registered.
Intermediate 8x8 multiplier
outputs are registered.
32-bit output from 16x16
multiplier is not registered.
32-bit output from 16x16
multiplier is registered.
16-bit output of Multiplexer
P, from top
adder/subtracter,
16-bit output from upper
accumulator register, Q
16-bit output from upper
8x8 multiplier, F
Upper 16-bit output from
16x16 multiplier, H
16-bit input from A input or
associated input register.
16-bit output from upper
8x8 multiplier, F
Upper 16-bit output from
16x16 multiplier, H
Sign extension input from
lower adder/subtracter,
Z[15]. Duplicate 16 bits.
16-bit feedback from upper
accumulator register, Q
16-bit input from C input or
associated pipeline register
Constant 0
Constant 1
Cascade Carry/borrow
output from lower
adder/subtracter
Carry/borrow output from
lower adder/subtracter
16-bit output of multiplexer
R from lower
adder/subtracter
16-bit output from lower
accumulator register, S
16-bit output from lower 8x8
135
11
BOTADDSUB_LOWERINPUT
C18,C17
Selects Input Z for
the lower
adder/subtracter
00
01
10
11
BOTADDSUB_UPPERINPUT
BOTADDSUB_CARRYSELECT
C19
C21,C20
Selects Input Y for
the lower
adder/subtracter
0
Carry/borrow input
select to lower
adder/subtracter
00
01
10
MODE_8x8
C22
Selects 8x8 Multiplier
mode and 8x8 LowPower Multiplier
Blocking Option
A_SIGNED
C23
Indicates whether
multiplier input A is
signed or unsigned.
Applies regardless if
input A is 16-or 32bits wide.
Indicates whether
multiplier input B is
signed or unsigned.
Applies regardless if
input B is 16-or 32bits wide.
B_SIGNED
C24
ICE Technology Library
Lattice Semiconductor Corporation Confidential
1
11
0
1
0
1
0
1
multiplier, G
Lower 16-bit output from
16x16 multiplier, H
16-bit input from B input or
associated pipeline register
16-bit output from lower
8x8 multiplier, G
Lower 16-bit output from
16x16 multiplier, H
Sign extension input
SIGNEXTIN. Duplicate 16
bits.
16-bit feedback from lower
accumulator register, S
16-bit input from D input or
associated input register.
Constant 0
Constant 1
Cascade Carry/borrow input
from ACCUMCI
Carry/borrow input from CI
No effect
Selects 8x8 Multiplier mode.
Holds the pipelining
registers associate with a
16x16 multiplier in clock
disable mode. Helps reduce
the dynamic power
consumption within the
multiplier function. Used in
conjunction with C6, C7
settings.
Multiplier input A is
unsigned.
Multiplier input A is signed.
Multiplier input B is
unsigned.
Multiplier input B is signed.
136
SB_MAC16 Configurations
The following SB_MAC16 functional blocks are supported in iCEcube2.
1. Multiplier.
2. Multiply and Accumulate (MAC).
3. Accumulator (ACC).
4. Add/Subtract (ADD/SUB).
5. Multiply and Add/Subtract (MULTADDSUB)
The valid configuration parameter settings for each functional block are listed below.
Note: Read the configuration settings from left to right while filling the SB_MAC16 instance parameter
values.
Table 1 : Multiplier Configurations
A_REG
B_REG
D_REG
TOP_8x8_MULT_REG
BOT_8x8_MULT_REG
PIPELINE_16x16_MULT_REG1
PIPELINE_16x16_MULT_REG2
C_REG
CBIT[0]
CBIT[1]
CBIT[2]
CBIT[3]
CBIT[4]
CBIT[5]
CBIT[6]
CBIT[7]
CBIT[8]
CBIT[9]
TOPOUTPUT_SELECT
TOPADDSUB_LOWERINPUT
CBIT[10]
TOPADDSUB_UPPERINPUT
CBIT[11]
CBIT[12]
TOPADDSUB_CARRYSELECT
CBIT[13]
CBIT[14]
CBIT[15]
CBIT[16]
BOTOUTPUT_SELECT
BOTADDSUB_LOWERINPUT
CBIT[17]
BOTADDSUB_UPPERINPUT
CBIT[18]
CBIT[19]
BOTADDSUB_CARRYSELECT
CBIT[20]
A_SIGNED
MODE_8x8
CBIT[21]
CBIT[22]
CBIT[23]
CBIT[24]
SB_MAC16
Function/
Parameter
Settings
B_SIGNED
8x8 Multiplier : 8x8 input multiplier with 16 bit output.
16x16 Multiplier: 16x16 input multiplier with 32 bit output.
8x8 Multiplier
mult_8x8_all_pipel
ined_unsigned
mult_8x8_all_pipel
ined_signed
mult_8x8_bypass_
unsigned
mult_8x8_bypass_
signed
0 0 1 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 1 1 1 0 1 1 0
1 1 1 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 1 1 1 0 1 1 0
0 0 1 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
1 1 1 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
16x16 Multiplier
mult_16x16_all_pi
pelined_unsigned
0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 1 1 1 1 0 1 1 0
ICE Technology Library
Lattice Semiconductor Corporation Confidential
137
mult_16x16_all_pi
pelined_signed
mult_16x16_inter
mediate_register_
bypassed_unsigne
d
mult_16x16_inter
mediate_register_
bypassed_signed
mult_16x16_bypas
s_unsigned
mult_16x16_bypas
s_signed
1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 1 1 1 1 0 1 1 0
0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 1 0 0 0 0 1 1 0
1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 1 0 0 0 0 1 1 0
0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0
1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0
Table 2 : MAC Configurations
A_REG
B_REG
D_REG
TOP_8x8_MULT_REG
BOT_8x8_MULT_REG
PIPELINE_16x16_MULT_REG1
PIPELINE_16x16_MULT_REG2
C_REG
CBIT[0]
CBIT[1]
CBIT[2]
CBIT[3]
CBIT[4]
CBIT[5]
CBIT[6]
CBIT[7]
CBIT[8]
CBIT[9]
TOPOUTPUT_SELECT
TOPADDSUB_LOWERINPUT
CBIT[10]
TOPADDSUB_UPPERINPUT
CBIT[11]
CBIT[12]
TOPADDSUB_CARRYSELECT
CBIT[13]
CBIT[14]
CBIT[15]
CBIT[16]
BOTOUTPUT_SELECT
BOTADDSUB_LOWERINPUT
CBIT[17]
BOTADDSUB_UPPERINPUT
CBIT[18]
CBIT[19]
BOTADDSUB_CARRYSELECT
CBIT[20]
A_SIGNED
MODE_8x8
CBIT[21]
CBIT[22]
CBIT[23]
CBIT[24]
SB_MAC16
Function/
Parameter Settings
B_SIGNED
16 bit MAC: 8x8 input, 16 bit output MAC.
32 bit MAC: 16x16 input, 32 bit output MAC.
16 bit MAC
mac_16_all_pipelin
ed_unsigned
mac_16_intermedia
te_register_bypasse
d_unsigned
mac_16_bypassed_
unsigned
0 0 1 0 0 0 0 1 0 1 0 0 0 0 1 0 1 1 1 1 1 1 1 1 1
0 0 1 0 0 0 0 1 0 1 0 0 0 0 1 0 1 0 0 0 0 1 1 1 1
0 0 1 0 0 0 0 1 0 1 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0
32 bit MAC
mac_32_all_pipelin
ed_unsigned
0 0 0 0 0 0 1 0 0 1 1 0 0 1 0 0 1 1 1 1 1 1 1 1 1
ICE Technology Library
Lattice Semiconductor Corporation Confidential
138
mac_32_all_pipelin
ed_cascaded_unsig
ned
mac_32_all_pipelin
ed_cin_unsigned
mac_32_intermedia
te_register_bypasse
d_unsigned
mac_32_intermedia
te_register_bypasse
d_cascaded_unsign
ed
mac_32_intermedia
te_register_bypasse
d_cin_unsigned
mac_32_bypassed_
unsigned
mac_32_bypassed_
cascaded_unsigned
mac_32_bypassed_
cin_unsigned
mac_32_intermedia
te_register_bypasse
d_signed
0 0 0 1 0 0 1 0 0 1 1 0 0 1 0 0 1 1 1 1 1 1 1 1 1
0 0 0 1 1 0 1 0 0 1 1 0 0 1 0 0 1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 1 0 0 1 1 0 0 1 0 0 1 1 0 0 0 1 1 1 1
0 0 0 1 0 0 1 0 0 1 1 0 0 1 0 0 1 1 0 0 0 1 1 1 1
0 0 0 1 1 0 1 0 0 1 1 0 0 1 0 0 1 1 0 0 0 1 1 1 1
0 0 0 0 0 0 1 0 0 1 1 0 0 1 0 0 1 0 0 0 0 0 0 0 0
0 0 0 1 0 0 1 0 0 1 1 0 0 1 0 0 1 0 0 0 0 0 0 0 0
0 0 0 1 1 0 1 0 0 1 1 0 0 1 0 0 1 0 0 0 0 0 0 0 0
1 1 0 0 0 0 1 0 0 1 1 0 0 1 0 0 1 1 0 0 0 1 1 1 1
Table 3 : ACCUMULATOR Configurations
ICE Technology Library
Lattice Semiconductor Corporation Confidential
139
C_REG
A_REG
B_REG
D_REG
TOP_8x8_MULT_REG
BOT_8x8_MULT_REG
PIPELINE_16x16_MULT_REG1
PIPELINE_16x16_MULT_REG2
16 bit
CBIT[0]
CBIT[1]
CBIT[2]
CBIT[3]
CBIT[4]
CBIT[5]
CBIT[6]
CBIT[7]
CBIT[8]
CBIT[9]
TOPOUTPUT_SELECT
TOPADDSUB_LOWERINPUT
CBIT[10]
TOPADDSUB_UPPERINPUT
CBIT[11]
CBIT[12]
TOPADDSUB_CARRYSELECT
CBIT[13]
CBIT[14]
CBIT[15]
CBIT[16]
BOTOUTPUT_SELECT
BOTADDSUB_LOWERINPUT
CBIT[17]
BOTADDSUB_UPPERINPUT
CBIT[18]
CBIT[19]
BOTADDSUB_CARRYSELECT
CBIT[20]
A_SIGNED
MODE_8x8
CBIT[21]
CBIT[22]
CBIT[23]
CBIT[24]
SB_MAC16
Function/
Parameter
Settings
B_SIGNED
16 bit ACCUMULATOR: 16 bit input, 16 bit output Accumulator.
32 bit ACCUMULATOR: 32 bit input, 32 bit output Accumulator.
ACCUMULATOR
acc_16_all_pipel
ined_unsigned
acc_16_bypasse
d_unsigned
0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 1 1 1 1
0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
32 bit
ACCUMULATOR
acc_32_all_pipel
ined_unsigned
acc_32_all_pipel
ined_cascaded_
unsigned
acc_32_all_pipel
ined_cin_unsign
ed
acc_32_bypasse
d_unsigned
acc_32_bypasse
d_cascaded_uns
igned
acc_32_bypasse
d_cin_unsigned
0 0 1 0 0 0 0 0 0 1 1 0 0 0 0 0 1 0 0 0 0 1 1 1 1
0 0 1 1 0 0 0 0 0 1 1 0 0 0 0 0 1 0 0 0 0 1 1 1 1
0 0 1 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 0 0 1 1 1 1
0 0 1 0 0 0 0 0 0 1 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0
0 0 1 1 0 0 0 0 0 1 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0
0 0 1 1 1 0 0 0 0 1 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0
Table 4: Add/Subtract Configurations
16 bit ADDSUB
add_sub_16_all_
pipelined_unsign
ed
A_REG
B_REG
D_REG
TOP_8x8_MULT_REG
BOT_8x8_MULT_REG
PIPELINE_16x16_MULT_REG1
PIPELINE_16x16_MULT_REG2
C_REG
CBIT[0]
CBIT[1]
CBIT[2]
CBIT[3]
CBIT[4]
CBIT[5]
CBIT[6]
CBIT[7]
CBIT[8]
CBIT[9]
TOPOUTPUT_SELECT
TOPADDSUB_LOWERINPUT
CBIT[10]
TOPADDSUB_UPPERINPUT
CBIT[11]
CBIT[12]
TOPADDSUB_CARRYSELECT
CBIT[13]
CBIT[14]
CBIT[15]
CBIT[16]
BOTOUTPUT_SELECT
BOTADDSUB_LOWERINPUT
CBIT[17]
BOTADDSUB_UPPERINPUT
CBIT[18]
CBIT[19]
BOTADDSUB_CARRYSELECT
CBIT[20]
A_SIGNED
MODE_8x8
CBIT[21]
CBIT[22]
CBIT[23]
CBIT[24]
SB_MAC16
Function/
Parameter
Settings
B_SIGNED
16 bit ADDSUB: 16 bit input, 16 bit output ADDSUB.
32 bit ADDSUB: 32 bit input, 32 bit output ADDSUB.
0 0 1 0 0 1 0 0 0 1 0 0 1 0 0 0 1 0 0 0 0 1 1 1 1
ICE Technology Library
Lattice Semiconductor Corporation Confidential
140
add_sub_16_byp
assed_unsigned
32 bit ADDSUB
add_sub_32_all_
pipelined_unsign
ed
add_sub_32_all_
pipelined_cascad
ed_unsigned
add_sub_32_all_
pipelined_cin_un
signed
add_sub_32_byp
assed_unsigned
add_sub_32_byp
assed_cascaded_
unsigned
add_sub_32_byp
assed_cin_unsig
ned
0 0 1 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0
0 0 1 0 0 1 0 0 0 1 1 0 1 0 0 0 1 0 0 0 0 1 1 1 1
0 0 1 1 0 1 0 0 0 1 1 0 1 0 0 0 1 0 0 0 0 1 1 1 1
0 0 1 1 1 1 0 0 0 1 1 0 1 0 0 0 1 0 0 0 0 1 1 1 1
0 0 1 0 0 1 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0
0 0 1 1 0 1 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0
0 0 1 1 1 1 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0
Table 5: Multiply Add/Subtract Configurations
PIPELINE_16x16_MULT_REG2
PIPELINE_16x16_MULT_REG1
BOT_8x8_MULT_REG
TOP_8x8_MULT_REG
D_REG
B_REG
A_REG
C_REG
TOPOUTPUT_SELECT
TOPADDSUB_LOWERINPUT
TOPADDSUB_UPPERINPUT
TOPADDSUB_CARRYSELECT
BOTOUTPUT_SELECT
BOTADDSUB_LOWERINPUT
BOTADDSUB_UPPERINPUT
BOTADDSUB_CARRYSELECT
CBIT[24]
CBIT[23]
CBIT[22]
CBIT[21]
CBIT[20]
CBIT[19]
CBIT[18]
CBIT[17]
CBIT[16]
CBIT[15]
CBIT[14]
CBIT[13]
CBIT[12]
CBIT[11]
CBIT[10]
CBIT[9]
CBIT[8]
CBIT[7]
CBIT[6]
CBIT[5]
CBIT[4]
CBIT[3]
CBIT[2]
CBIT[1]
CBIT[0]
SB_MAC16 Function/
Parameter Settings
B_SIGNED
A_SIGNED
MODE_8x8
16 bit Mult-Add/Sub: 8x8 input, 16 bit output Mult-Add/Sub.
32 bit Mult-Add/Sub: 16x16 input, 32 bit output Mult-Add/Sub.
16 bit Mult-Add/Sub
mult_add_sub_16_all
_pipelined_unsigned
0 0 1 0 0 1 0 1 0 1 0 0 1 0 1 0 1 1 1 1 1 1 1 1 1
ICE Technology Library
Lattice Semiconductor Corporation Confidential
141
mult_add_sub_16_int
ermediate_register_b
ypassed_unsigned
mult_add_sub_16_by
passed_unsigned
32 bit Mult-Add/Sub
mult_add_sub_32_all
_pipelined_unsigned
mult_add_sub_32_all
_pipelined_cascaded_
unsigned
mult_add_sub_32_all
_pipelined_cin_unsig
ned
mult_add_sub_32_int
ermediate_register_b
ypassed_unsigned
mult_add_sub_32_int
ermediate_register_b
ypassed_cascaded_u
nsigned
mult_add_sub_32_int
ermediate_register_b
ypassed_cin_unsigne
d
mult_add_sub_32_by
passed_unsigned
mult_add_sub_32_by
passed_cascaded_uns
igned
mult_add_sub_32_by
passed_cin_unsigned
mult_add_sub_32_int
ermediate_register_b
ypassed_signed
0 0 1 0 0 1 0 1 0 1 0 0 1 0 1 0 1 0 0 0 0 1 1 1 1
0 0 1 0 0 1 0 1 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 1 1 0 0 1 1 0 1 1 0 0 1 1 1 1 1 1 1 1 1
0 0 0 1 0 1 1 0 0 1 1 0 1 1 0 0 1 1 1 1 1 1 1 1 1
0 0 0 1 1 1 1 0 0 1 1 0 1 1 0 0 1 1 1 1 1 1 1 1 1
0 0 0 0 0 1 1 0 0 1 1 0 1 1 0 0 1 1 0 0 0 1 1 1 1
0 0 0 1 0 1 1 0 0 1 1 0 1 1 0 0 1 1 0 0 0 1 1 1 1
0 0 0 1 1 1 1 0 0 1 1 0 1 1 0 0 1 1 0 0 0 1 1 1 1
0 0 0 0 0 1 1 0 0 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0
0 0 0 1 0 1 1 0 0 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0
0 0 0 1 1 1 1 0 0 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0
1 1 0 0 0 1 1 0 0 1 1 0 1 1 0 0 1 1 0 0 0 1 1 1 1
ICE Technology Library
Lattice Semiconductor Corporation Confidential
142
Verilog Instantiation
SB_MAC16 i_sbmac16
(
.A(A_i),
.B(B_i),
.C(C_i),
.D(D_i),
.O(O),
.CLK(SYSCLK_i),
.CE(CE_i),
.IRSTTOP(RST_i),
.IRSTBOT(RST_i),
.ORSTTOP(RST_i),
.ORSTBOT(RST_i),
.AHOLD(AHOLD_i),
.BHOLD(BHOLD_i),
.CHOLD(CHOLD_i),
.DHOLD(DHOLD_i),
.OHOLDTOP(HLDTOPOUT_i),
.OHOLDBOT(HLDBOTOUT_i),
.OLOADTOP(LOADTOP_i),
.OLOADBOT(LOADBOT_i),
.ADDSUBTOP(ADDSUBTOP_i),
.ADDSUBBOT(ADDSUBBOT_i),
.CO(CO),
.CI(CI),
//MAC cascading ports.
.ACCUMCI(),
.ACCUMCO(),
.SIGNEXTIN(),
.SIGNEXTOUT()
);
// mult_8x8_all_pipelined_unsigned [24:0] = 001_0000010_0000010_0111_0110
// Read configuration settings [24:0] from left to right while filling the
instance parameters.
defparam i_sbmac16. B_SIGNED
defparam i_sbmac16. A_SIGNED
defparam i_sbmac16. MODE_8x8
= 1'b0
= 1'b0
= 1'b1
;
;
;
defparam
defparam
defparam
defparam
i_sbmac16.
i_sbmac16.
i_sbmac16.
i_sbmac16.
BOTADDSUB_CARRYSELECT
BOTADDSUB_UPPERINPUT
BOTADDSUB_LOWERINPUT
BOTOUTPUT_SELECT
=
=
=
=
2'b00
1'b0
2'b00
2'b10
;
;
;
;
defparam
defparam
defparam
defparam
i_sbmac16.
i_sbmac16.
i_sbmac16.
i_sbmac16.
TOPADDSUB_CARRYSELECT
TOPADDSUB_UPPERINPUT
TOPADDSUB_LOWERINPUT
TOPOUTPUT_SELECT
=
=
=
=
2'b00
1'b0
2'b00
2'b10
;
;
;
;
defparam
defparam
defparam
defparam
defparam
defparam
defparam
defparam
i_sbmac16.
i_sbmac16.
i_sbmac16.
i_sbmac16.
i_sbmac16.
i_sbmac16.
i_sbmac16.
i_sbmac16.
PIPELINE_16x16_MULT_REG2
PIPELINE_16x16_MULT_REG1
BOT_8x8_MULT_REG
TOP_8x8_MULT_REG
D_REG
B_REG
A_REG
C_REG
=
=
=
=
=
=
=
=
1'b0
1'b1
1'b1
1'b1
1'b0
1'b1
1'b1
1'b0
;
;
;
;
;
;
;
;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
143
iCE40UL (iCE40 Ultra Lite) Hard Macros
This section describes the following dedicated hard macro primitives available in iCE40UL device.
SB_HFOSC
SB_LFOSC
SB_RGBA_DRV
SB_IR400_DRV
SB_BARCODE_DRV
SB_IR500_DRV
SB_LEDDA_IP
SB_IR_IP
SB_IO_OD
SB_I2C_FIFO
SB_HFOSC
SB_HFOSC primitive generates 48MHz nominal clock frequency within +/- 10% variation, with user
programmable divider value of 1, 2, 4, and 8. The HFOSC can drive either the global clock network or
fabric routes directly based on the clock network selection.
Ports
SB_HFOSC Ports
Signal Name
Direction
CLKHFPU
Input
CLKHFEN
Input
CLKHF
Output
Description
Power up the HFOSC circuit. After power up, oscillator
output will be stable after 100us. Active High.
Enable the clock output. Enable should be low for the
100us power up period. Active High.
HF Oscillator output.
Parameters
Parameter
Parameter Values.
CLKHF_DIV
"0b00"
"0b01"
"0b10"
"0b11"
Description.
Sets 48MHz HFOSC output.
Sets 24MHz HFOSC output.
Sets 12MHz HFOSC output.
Sets 6MHz HFOSC output
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input CLKHFEN: Logic “0”
Input CLKHFPU: Logic “0”
ICE Technology Library
Lattice Semiconductor Corporation Confidential
144
Clock Network Selection
By default the oscillator use one of the dedicated clock networks in the device to drive the elements. The
user may configure the oscillator to use the fabric routes instead of global clock network using the
synthesis attribute.
Synthesis Attributes
/* synthesis ROUTE_THROUGH_FABRIC = <value> */
Value:
0: Use dedicated clock network. Default option.
1: Use fabric routes.
Verilog Instantiation
SB_HFOSC OSCInst0 (
.CLKHFEN(ENCLKHF),
.CLKHFPU(CLKHF_POWERUP),
.CLKHF(CLKHF)
) /* synthesis ROUTE_THROUGH_FABRIC= [0|1] */;
defparam OSCInst0.CLKHF_DIV = "0b00";
SB_LFOSC
SB_LFOSC primitive generates 10 KHz nominal clock frequency within +/- 10% variation. There is no
divider on the LFOSC.
The LFOSC can drive either the global clock network or fabric routes directly based on the clock network
selection
Ports
SB_LFOSC Ports
Signal Name
Direction
CLKLFPU
Input
CLKLFEN
Input
CLKLF
Output
Description
Power up the LFOSC circuit. After power up, oscillator
output will be stable after 100us. Active High.
Enable the clock output. Enable should be low for the
100us power up period. Active High.
LF Oscillator output.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input CLKLFEN: Logic “0”
Input CLKLFPU: Logic “0”
ICE Technology Library
Lattice Semiconductor Corporation Confidential
145
Clock Network Selection
By default the oscillator use one of the dedicated clock networks in the device to drive the elements. The
user may configure the oscillator to use the fabric routes instead of global clock network using the
synthesis attribute.
Synthesis Attributes
/* synthesis ROUTE_THROUGH_FABRIC = <value> */
Value:
0: Use dedicated clock network. Default option.
1: Use fabric routes.
Verilog Instantiation
SB_LFOSC OSCInst1 (
.CLKLFEN(ENCLKLF),
.CLKLFPU(CLKLF_POWERUP),
.CLKLF(CLKLF)
) /* synthesis ROUTE_THROUGH_FABRIC= [0|1] */;
SB_RGBA_DRV
SB_RGBA_DRV primitive is the RGB LED drive module which contains 3 dedicated open drain I/O pins
for RGB LED outputs. Each of the RGB LED output is bonded out together with an SB_IO_OD primitive
to the package pin. User can either use SB_RGB_DRV primitive or the SB_IO_OD primitive to drive the
package pin, but not both.
The primitive allows configuration of each of the 3 RGB LED outputs individually. When the
RGBx_CURRENT parameter of RGBx output is set to "0b000000", then SB_IO_OD can be used to drive
the package pin.
Ports
Signal Name
SB_RGBA_DRV Ports
Direction
CURREN
Input
RGBLEDEN
RGB0PWM
Input
Input
RGB1PWM
Input
Description
Enable the mixed signal control block to supply reference
current to the IR drivers. When it is not enabled
(CURREN=0), no current is supplied, and the IR drivers
are powered down. Enabling the mixed signal control
block takes 100us to reach a stable reference current
value.
Enable the SB_RGB_DRV primitive. Active High.
Input data to drive RGB0 LED pin. This input is usually
driven from the SB_LEDD_IP.
Input data to drive RGB1 LED pin. This input is usually
ICE Technology Library
Lattice Semiconductor Corporation Confidential
146
RGB2PWM
Input
Output
Output
Output
RGB0
RGB1
RGB2
driven from the SB_LEDD_IP.
Input data to drive RGB2 LED pin. This input is usually
driven from the SB_LEDD_IP.
RGB0 LED output.
RGB1 LED output.
RGB2 LED output.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input CURREN
: Logic “0”
Input RGBLEDEN
: Logic “0”
Input RGB0PWM
: Logic “0”
Input RGB1PWM
: Logic “0”
Input RGB2PWM
: Logic “0”
Parameters
The SB_RGBA_DRV primitive contains the following parameter and their default values:
Parameter CURRENT_MODE = "0b0 ";
Parameter values:
"0b0" = Full Current Mode (Default).
"0b1" = Half Current Mode.
Parameter RGB0_CURRENT = "0b000000";
Parameter RGB1_CURRENT = "0b000000";
Parameter RGB2_CURRENT = "0b000000";
Parameter values:
"0b000000" = 0mA. // Set this value to use the associated SB_IO_OD instance at RGB
// LED location.
"0b000001" = 4mA for Full Mode; 2mA for Half Mode
"0b000011" = 8mA for Full Mode; 4mA for Half Mode
"0b000111" = 12mA for Full Mode; 6mA for Half Mode.
"0b001111" = 16mA for Full Mode; 8mA for Half Mode
"0b011111" = 20mA for Full Mode; 10mA for Half Mode.
"0b111111" = 24mA for Full Mode; 12mA for Half Mode.
Verilog Instantiation
SB_RGBA_DRV RGBA_DRIVER (
.CURREN(ENABLE_CURR),
.RGBLEDEN(ENABLE_RGBDRV),
.RGB0PWM(RGB0),
.RGB1PWM(RGB1),
.RGB2PWM(RGB2),
.RGB0(LED0),
.RGB1(LED1),
.RGB2(LED2)
);
defparam
defparam
defparam
defparam
RGBA_DRIVER.CURRENT_MODE
RGBA_DRIVER.RGB0_CURRENT
RGBA_DRIVER.RGB1_CURRENT
RGBA_DRIVER.RGB2_CURRENT
=
=
=
=
"0b0";
"0b111111";
"0b111111" ;
"0b111111";
ICE Technology Library
Lattice Semiconductor Corporation Confidential
147
SB_IR400_DRV
SB_IR400_DRV primitive is the IR driver which contains a single dedicated open drain I/O pin for IRLED
output. The IRLED output is bonded out together with an SB_IO_OD primitive to the package pin. User
can either use SB_IR400_DRV primitive or the SB_IO_OD primitive to drive the package pin, but not
both.
When the IR400_CURRENT parameter is set to "0b00000000", then SB_IO_OD can be used to drive the
package pin.
Ports
SB_IR400_DRV Ports
Signal Name
Direction
CURREN
Input
IRLEDEN
IRPWM
IRLED
Input
Input
Output
Description
Enable the mixed signal control block to supply reference
current to the IR drivers. When it is not enabled
(CURREN=0), no current is supplied, and the IR drivers are
powered down. Enabling the mixed signal control block
takes 100us to reach a stable reference current value.
Enable the SB_IR400_DRV primitive. Active High.
PWM Input data to drive IRLED pin.
IR LED output.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input CURREN
: Logic “0”
Input IRLEDEN
: Logic “0”
Input IRPWM
: Logic “0”
Parameter
The SB_IR400_DRV primitive contains the following parameter and their default values:
Parameter CURRENT_MODE = "0b0 ";
Parameter values:
"0b0" = Full Current Mode (Default).
"0b1" = Half Current Mode.
Parameter IR400_CURRENT = "0b00000000";
Parameter Values:
"0b0000000000"; = 0mA. //This is the setting to tristate the IR output to allow it to be
used as GPIO (SB_IO_OD)
"0b00000001"; = 50mA for Full Mode; 25mA for Half Mode.
"0b00000011"; = 100mA for Full Mode; 50mA for Half Mode.
"0b00000111"; = 150mA for Full Mode; 75mA for Half Mode.
"0b00001111"; = 200mA for Full Mode; 100mA for Half Mode.
"0b00011111"; = 250mA for Full Mode; 125mA for Half Mode.
"0b00111111"; = 300mA for Full Mode; 150mA for Half Mode.
"0b01111111"; = 350mA for Full Mode; 175mA for Half Mode.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
148
"0b11111111"; = 400mA for Full Mode; 200mA for Half Mode.
Verilog Instantiation
SB_IR400_DRV IRDRVinst (
.CURREN(ENABLE_CURRENT),
.IRLEDEN(ENABLE_IRDRV),
.IRPWM(IR_PWMINPUT),
.IRLED(IR_LEDOUT)
);
defparam IRDRVinst.CURRENT_MODE = "0b0";
defparam IRDRVinst.IR400_CURRENT = "0b1111111111";
SB_BARCODE_DRV
SB_BARCODE_DRV primitive contains a single dedicated open drain I/O pin for BARCODE output. The
BARCODE output is bonded out together with an SB_IO_OD primitive to the package pin. User can
either use SB_BARCODE_DRV primitive or the SB_IO_OD primitive to drive the package pin, but not
both.
When the BARCODE_CURRENT parameter is set to "0b0000", SB_IO_OD can be used to drive the
package pin.
Ports
Signal Name
CURREN
BARCODEN
BARCODEPWM
BARCODE
SB_BARCODE_DRV Ports
Direction
Input
Input
Input
Output
Description
Enable the mixed signal control block to supply reference
current to the IR drivers. When it is not enabled
(CURREN=0), no current is supplied, and the IR drivers are
powered down. Enabling the mixed signal control block
takes 100us to reach a stable reference current value.
Enable the SB_BARCODE_DRV primitive. Active High.
PWM Input data to drive BARCODE pin.
BARCODE output.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input CURREN
: Logic “0”
Input BARCODEEN
: Logic “0”
Input BARCODEPWM : Logic “0”
ICE Technology Library
Lattice Semiconductor Corporation Confidential
149
Parameter
The SB_BARCODE_DRV primitive contains the following parameter and their default values:
Parameter CURRENT_MODE = "0b0";
Parameter values:
"0b0" = Full Current Mode (Default).
"0b1" = Half Current Mode.
Parameter BARCODE_CURRENT = "0b0000";
Parameter values:
"0b0000" = 0mA.
//This is the setting to tristate the BARCODEoutput to allow it to be used
// as GPIO (SB_IO_OD)
"0b0001" = 16.6mA for Full Mode; 8.3mA for Half Mode,
"0b0011" = 33.3mA for Full Mode; 16.6mA for Half Mode,
"0b1001" = 66.6mA for Full Mode; 33.3mA for Half Mode,
"0b1010" = 83.3mA for Full Mode; 41.6mA for Half Mode,
"0b0111" = 50mA for Full Mode; 25mA for Half Mode,
"0b1111" = 100mA for Full Mode; 50mA for Half Mode
Verilog Instantiation
SB_BARCODE_DRV BARCODEDRVinst (
.CURREN(ENABLE_CURRENT),
.BARCODEEN(ENABLE_BARCODEDRV),
.BARCODEPWM(BARCODE_PWMINPUT),
.BARCODE(BARCODEOUT)
);
defparam BARCODEDRVinst.CURRENT_MODE = "0b0";
defparam BARCODEDRVinst.BARCODE_CURRENT = "0b1111";
SB_IR500_DRV
SB_IR500_DRV primitive is the IR driver which contains a two dedicated open drain I/O pin for IRLED1,
IRLED2 outputs. The IRLED outputs are bonded out together with an SB_IO_OD primitive to the package
pin. User can either use SB_IR500_DRV primitive or the SB_IO_OD primitive to drive the package pin,
but not both.
When the IR4500_CURRENT parameter is set to "0b00000000", then SB_IO_OD can be used to drive
the package pin.
SB_IR500_DRV DRC Rule
This primitive cannot be instantiated along with SB_BARCODE_DRV or SB_IR400_DRV instance.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
150
Ports
SB_IR500_DRV Ports
Signal Name
Direction
CURREN
Input
IRLEDEN
IRPWM
IRLED1
IRLED2
Input
Input
Output
Output
Description
Enable the mixed signal control block to supply reference
current to the IR drivers. When it is not enabled
(CURREN=0), no current is supplied, and the IR drivers are
powered down. Enabling the mixed signal control block
takes 100us to reach a stable reference current value.
Enable the SB_IR400_DRV primitive. Active High.
PWM Input data to drive IRLED pin.
IR LED output 1.
IR LED output 2.
Default Signal Values
The iCEcube2 software assigns the following signal value to unconnected port:
Input CURREN
: Logic “0”
Input IRLEDEN
: Logic “0”
Input IRPWM
: Logic “0”
Parameter
The SB_IR500_DRV primitive contains the following parameter and their default values:
Parameter CURRENT_MODE = "0b0";
Parameter values:
"0b0"; = Full Current Mode (Default).
"0b1"; = Half Current Mode.
Parameter IR500_CURRENT = “0b000000000000”;
Parameter values:
"0b000000000000"; = 0mA. // This is the setting to tristate the BARCODE output to allow it to
// be used as GPIO (SB_IO_OD).
"0b000000000111"; = 50mA for Full Mode; 25mA for Half Mode.
"0b000000001111"; = 100mA for Full Mode; 50mA for Half Mode.
"0b000000011111"; = 150mA for Full Mode; 75mA for Half Mode.
"0b000000111111"; = 200mA for Full Mode; 100mA for Half Mode.
"0b000001111111"; = 250mA for Full Mode; 125mA for Half Mode.
"0b000011111111"; = 300mA for Full Mode; 150mA for Half Mode.
"0b000111111111"; = 350mA for Full Mode; 175mA for Half Mode.
"0b001111111111"; = 400mA for Full Mode; 200mA for Half Mode.
"0b011111111111"; = 450mA for Full Mode; 225mA for Half Mode.
"0b111111111111"; = 500mA for Full Mode; 250mA for Half Mode.
Verilog Instantiation
SB_IR500_DRV IRDRVinst (
.CURREN(ENABLE_CURRENT),
.IRLEDEN(ENABLE_IRDRV),
.IRPWM(IR_PWMINPUT),
.IRLED(IR_LEDOUT)
);
defparam IRDRVinst.CURRENT_MODE = "0b0";
defparam IRDRVinst.IR500_CURRENT = "0b1111111111";
ICE Technology Library
Lattice Semiconductor Corporation Confidential
151
SB_LEDDA_IP
SB_LEDDA_IP primitive generates the RGB PWM outputs for the RGB LED drivers. The IP contains
registers that are programmed in by the SCI bus interface signals.
Ports
SB_LEDDA_IP Ports
Signal Name
Direction
LEDDCS
LEDDCLK
LEDDDAT7
LEDDDAT6
LEDDDAT5
LEDDDAT4
LEDDDAT3
LEDDDAT2
LEDDDAT1
LEDDDAT0
LEDDADDR3
LEDDADDR2
LEDDADDR1
LEDDADDR0
LEDDDEN
LEDDEXE
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
LEDDRST
Input
PWMOUT0
PWMOUT1
PWMOUT2
Output
Output
Output
Description
CS to write LEDD IP registers
Clock to write LEDD IP registers
bit 7 data to write into the LEDD IP registers
bit 6 data to write into the LEDD IP registers
bit 5 data to write into the LEDD IP registers
bit 4 data to write into the LEDD IP registers
bit 3 data to write into the LEDD IP registers
bit 2 data to write into the LEDD IP registers
bit 1 data to write into the LEDD IP registers
bit 0 data to write into the LEDD IP registers
LEDD IP register address bit 3
LEDD IP register address bit 2
LEDD IP register address bit 1
LEDD IP register address bit 0
Data enable input to indicate data and address are stable.
Enable the IP to run the blinking sequence. When it is
LOW, the sequence stops at the nearest OFF state.
Device level reset signal to reset all internal registers during
the device configuration. This port is not accessible to user
signals.
PWM output 0
PWM output 1
PWM output 2
ICE Technology Library
Lattice Semiconductor Corporation Confidential
152
LEDDON
Output
Indicating the LED is on
Default Signal Values
The iCEcube2 software assigns the logic “0” value to all unconnected input ports.
Verilog Instantiation
SB_LEDDA_IP PWMgen_inst (
.LEDDCS(ledd_cs),
.LEDDCLK(led_clk),
.LEDDDAT7(led_ip_data[7]),
.LEDDDAT6(led_ip_data[6]),
.LEDDDAT5(led_ip_data[5]),
.LEDDDAT4(led_ip_data[4]),
.LEDDDAT3(led_ip_data[3]),
.LEDDDAT2(led_ip_data[2]),
.LEDDDAT1(led_ip_data[1]),
.LEDDDAT0(led_ip_data[0]),
.LEDDADDR3(led_ip_addr[3]),
.LEDDADDR2(led_ip_addr[2]),
.LEDDADDR1(led_ip_addr[1]),
.LEDDADDR0(led_ip_addr[0]),
.LEDDDEN(led_ip_den),
.LEDDEXE(led_ip_exe),
.LEDDRST(led_ip_rst),
.PWMOUT0(LED0),
.PWMOUT1(LED1),
.PWMOUT2(LED2),
.LEDDON(led_on)
);
SB_IR_IP
SB_IR_IP primitive is the IR transceiver module. It generates or receives the modulated pulse
for the IR driver primitives.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
153
Ports
SB_IR_IP Ports
Signal Name
Direction
CLKI
CSI
Input
Input
DENI
Input
WEI
Input
ADRI3
ADRI2
ADRI1
ADRI0
WDATA7
WDATA6
WDATA5
WDATA4
WDATA3
WDATA2
WDATA1
WDATA0
RDATA7
RDATA6
RDATA5
RDATA4
RDATA3
RDATA2
RDATA1
RDATA0
EXE
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Output
Output
Output
Output
Output
Output
Output
Output
Input
LEARN
Input
BUSY
DRDY
ERR
RST
Output
Output
Output
Input
IRIN
IROUT
Input
Output
Description
Clock input for IR IP
Select Signal. Active High to activate the IP. This usually
connects to the output of the decoding logic from MSB of the
address bus
Data Enable. When asserted, indicates that the data and
address on the IR Transceiver Control Bus are stabilized and
ready to be captured.
Data Write Enable. Asserted during WRITE and de-asserted
during READ cycle.
Control Register Address Bit 3
Control Register Address Bit 2
Control Register Address Bit 1
Control Register Address Bit 0
Write Data Input Bit 7
Write Data Input Bit 6
Write Data Input Bit 5
Write Data Input Bit 4
Write Data Input Bit 3
Write Data Input Bit 2
Write Data Input Bit 1
Write Data Input Bit 0
Read Data Output Bit 7
Read Data Output Bit 6
Read Data Output Bit 5
Read Data Output Bit 4
Read Data Output Bit 3
Read Data Output Bit 2
Read Data Output Bit 1
Read Data Output Bit 0
Execute. when asserted, starts the IR Transceiver Hard IP to
transmit or receive IR data
Learning Mode control. When asserted the IR Transceiver is in
learning mode. The IR Transceiver will receive data instead of
transmit data.
Busy status output
Data Buffer Ready status output
Data Error status
Device level reset signal to reset all internal registers and
IROUT signal to OFF state during the device configuration. This
port is not accessible to user signals.
Modulated ON/OFF pulse from IR sensor.
Modulated ON/OFF pulse for IR Transmit.
Default Signal Values
The iCEcube2 software assigns the logic “0” value to all unconnected input ports.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
154
Verilog Instantiation
SB_IR_IP IRIP_inst (
.CLKI(sysclk_i),
.CSI(csi_i),
.DENI(deni_i),
.WEI(wei_i),
.ADRI3(addri_i[3]),
.ADRI2(addri_i[2]),
.ADRI1(addri_i[1]),
.ADRI0(addri_i[0]),
.WDATA7(wdata_i[7]),
.WDATA6(wdata_i[6]),
.WDATA5(wdata_i [5]),
.WDATA4(wdata_i [4]),
.WDATA3(wdata_i [3]),
.WDATA2(wdata_i [2]),
.WDATA1(wdata_i [1]),
.WDATA0(wdata_i [0]),
.RDATA7(rdata_o[7]),
.RDATA6(rdata_o[6]),
.RDATA5(rdata_o[5]),
.RDATA4(rdata_o[4]),
.RDATA3(rdata_o[3]),
.RDATA2(rdata_o[2]),
.RDATA1(rdata_o[1]),
.RDATA0(rdata_o[0]),
.EXE(exe_i),
.LEARN(learn_i),
.BUSY(busy_o),
.DRDY(drdy_o),
.ERR(err_o),
.RST(rst_i),
.IRIN(irin_i),
.IROUT(irpulse_w)
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
155
SB_IO_OD
The SB_IO_OD is the open drain IO primitive. When the Tristate output is enabled, the IO pulls down the
package pin signal to zero. The following figure and Verilog template illustrate the complete user
accessible logic diagram, and its Verilog instantiation.
Ports
SB_IO_OD Ports
Signal Name
PACKAGEPIN
LATCHINPUTVALUE
CLOCKENABLE
INPUTCLK
OUTPUTCLK
OUTPUTENABLE
DOUT0
DOUT1
DIN0
DIN1
Direction
Bidirectional
Input
Input
Input
Input
Input
Input
Input
Output
Output
Description
Bidirectional IO pin.
Latches/Holds the input data.
Clock enable signal.
Clock for the input registers.
Clock for the output registers.
Enable Tristate output. Active high.
Data to package pin.
Data to package pin.
Data from package pin.
Data from package pin.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
156
Default Signal Values
The iCEcube2 software assigns the logic “0” value to all unconnected input ports except for
CLOCKENABLE.
Note that explicitly connecting logic “1” value to port CLOCKENABLE will result in a non-optimal
implementation, since extra LUT will be used to generate the Logic “1”. If the user’s intention is to keep
the Input and Output registers always enabled, it is recommended that port CLOCKENABLE to be left
unconnected.
Parameter Values
Parameter PIN_TYPE = 6’b000000;
// See Input and Output Pin Function Tables in SB_IO.
// Default value of PIN_TYPE = 6’b000000
Parameter NEG_TRIGGER = 1’b0;
// Specify the polarity of all FFs in the I/O to be falling edge when
NEG_TRIGGER = 1.
Default is 1’b0, rising edge.
Input and Output Pin Function Tables
Refer SB_IO Input and Output Pin Functional Table for the PIN_TYPE settings. Some of the
output pin configurations are not applicable for SB_IO_OD primitive.
Verilog Instantiation
SB_IO_OD
OpenDrainInst0
(
.PACKAGEPIN (PackagePin),
.LATCHINPUTVALUE (latchinputvalue),
.CLOCKENABLE (clockenable),
.INPUTCLK (inputclk),
.OUTPUTCLK (outputclk),
.OUTPUTENABLE (outputenable),
.DOUT0 (dout0),
.DOUT1 (dout1),
.DIN0 (din0),
.DIN1 (din1)
// User’s Pin signal name
// Latches/holds the Input value
// Clock Enable common to input and
// output clock
// Clock for the input registers
// Clock for the output registers
// Output Pin Tristate/Enable
// control
// Data 0 – out to Pin/Rising clk
// edge
// Data 1 - out to Pin/Falling clk
// edge
// Data 0 - Pin input/Rising clk
// edge
// Data 1 – Pin input/Falling clk
// edge
);
defparam OpenDrainInst0.PIN_TYPE = 6'b000000;
defparam OpenDrainInst0.NEG_TRIGGER = 1'b0;
ICE Technology Library
Lattice Semiconductor Corporation Confidential
157
SB _I2C_FIFO
iCE40UL device supports two I2C hard IP primitives , located at bottom left corner and bottom right
corner of the chip.
Ports
SB_I2C_FIFO Ports
Signal Name
Direction
CLKI
CSI
Input
Input
STBI
WEI
ADRI3
ADRI2
ADRI1
ADRI0
DATI9
DATI8
DATI7
DATI6
DATI5
DATI4
DATI3
DATI2
DATI1
DATI0
DATO9
DATO8
DATO7
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Output
Output
Output
Description
System Clock input
Select Signal. Active High to activate the IP. This usually
connects to the output of the decoding logic from MSB of the
address bus
Strobe Signal
Write Enable Signal
Control Register Address Bit 3
Control Register Address Bit 2
Control Register Address Bit 1
Control Register Address Bit 0
Data Input Bit 9
Data Input Bit 8
Data Input Bit 7
Data Input Bit 6
Data Input Bit 5
Data Input Bit 4
Data Input Bit 3
Data Input Bit 2
Data Input Bit 1
Data Input Bit 0
Data Output Bit 9
Data Output Bit 8
Data Output Bit 7
ICE Technology Library
Lattice Semiconductor Corporation Confidential
158
DATO6
DATO5
DATO4
DATO3
DATO2
DATO1
DATO0
ACKO
I2CIRQ
I2CWKUP
SRWO
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Data Output Bit 6
Data Output Bit 5
Data Output Bit 4
Data Output Bit 3
Data Output Bit 2
Data Output Bit 1
Data Output Bit 0
Acknowledgement
I2C Interrupt output
I2C Wake up from Standby signal
Slave RW “1” master receiving / Slave transmitting
“0” master transmitting / Slave receiving
SCLI
Input
Serial Clock Input
SCLO
Output
Serial Clock Output
SCLOE
Output
Serial Clock Output Enable. Active High
SDAI
Input
Serial Data Input
SDAO
Output
Serial Data Output
SDAOE
Output
Serial Data Output Enable. Active High
1
FIFORST
Input
RESET for the FIFO logic
1
TXFIFOAEMPTY
Output
TX FIFO Status Signal
1
TXFIFOEMPTY
Output
TX FIFO Status Signal
1
TXFIFOFULL
Output
TX FIFO Status Signal
1
RXFIFOAFULL
Output
RX FIFO Status Signal
1
RXFIFOFULL
Output
RX FIFO Status Signal
1
RXFIFOEMPTY
Output
RX FIFO Status Signal
1
MRDCMPL
Output
Master Read Complete (only valid for Master Read Mode)
1
Note : Only available if I2C_FIFO_ENB = ENABLED.
Parameters
I2C Location
Left Side Corner
Parameters
I2C_SLAVE _ADDR
Parameter Default
0b1111100001
Right Side
I2C_SLAVE _ADDR
0b1111100010
Description
Upper Bits <9:2> can be changed
through control registers. Lower
bits <1:0> are fixed.
Upper Bits <9:2> can be changed
through control registers. Lower
bits <1:0> are fixed.
Synthesis Attribute
I2C_CLK_DIVIDER
Synthesis attribute “I2C_CLK_DIVIDER” is used by PNR and STA tools for optimization and deriving the
appropriate clock frequency at SCLO output with respect to the SBCLKI input clock frequency.
/* synthesis I2C_CLK_DIVIDER= Divide Value */
Divide Value: 0, 1, 2, 3 … 1023. Default is 0.
SDA_INPUT_DELAYED
SDA_INPUT_DELAYED attribute is used to add 50ns additional delay to the SDAI signal.
/* synthesis SDA_INPUT_DELAYED= value */
ICE Technology Library
Lattice Semiconductor Corporation Confidential
159
Value:
0: No delay.
1: Add 50ns delay. (Default value).
SDA_OUTPUT_DELAYED
SDA_OUTPUT_DELAYED attribute is used to add 50ns additional delay to the SDAO signal.
/* synthesis SDA_OUTPUT_DELAYED= value */
Value:
0: No delay (Default value).
1: Add 50ns delay.
I2C_FIFO_ENB
“I2C_FIFO_ENB” attribute is used to enable or disable FIFO
/* synthesis I2C_FIFO_ENB= [value] */
Value:
ENABLED : FIFO mode will be enabled.
DISABLED : FIFO mode will be disabled.
ICE Technology Library
Lattice Semiconductor Corporation Confidential
160
Device Configuration Primitives
SB_WARMBOOT
iCE FPGA devices permit the user to load a different configuration image during regular operation.
Through the use of the Warm Boot Primitive, the user can load one of 4 pre-defined configuration images
into the iCE FPGA device.
Note that this Warm Boot mode is different from the Cold Boot operation, which is executed during the
initial device boot-up sequence.
BOOT
SB_WARMBOOT
S1
S0
The selection of one of these 4 images is accomplished through 2 input signals, S1 and S0. In order to
trigger the selection of a new image, an additional signal, BOOT, is provided. It should be noted that this
signal is level-triggered, and should be used for every Warm Boot operation i.e. every time the user
wishes to load a new image into the device.
The successful instantiation of this primitive also requires the user to specify the address locations of the
4 images. These addresses should be specified in the iCEcube2 software as per the Warm Boot
Application Note.
Verilog Instantiation
SB_WARMBOOT my_warmboot_i
.BOOT (my_boot),
.S1 (my_sel1),
(
// Level-sensitive trigger signal
// S1, S0 specify selection of the
// configuration image
.S0 (my_sel0)
);
ICE Technology Library
Lattice Semiconductor Corporation Confidential
161