Datasheet

UNISONIC TECHNOLOGIES CO., LTD
U74HCT73
CMOS IC
DUAL J-K FLIP-FLOPS WITH
CLEAR AND PRESET
DESCRIPTION

The U74HCT73 is a dual J-K negative-edge-triggered flip-flop.
The clear ( CLR ) input can reset the output at a low level,
regardless of the level of others inputs. when the CLR is
inactive(high), data at the data inputs meeting the set-up time
requirements are transferred to the outputs on the negative-going
edge of the clock pulse. Following the hold-time interval, data J and
k inputs can be changed without affecting the levels at the outputs.
FEATURES

* Wide supply voltage range from 4.5V to 5.5V
* Low static power consumption; ICC=4μA (Max.)
ORDERING INFORMATION

Ordering Number
U74HCT73G-S14-R
U74HCT73G-S14-R
Package
SOP-14
(1)Packing Type
(1) R: Tape Reel
(2)Package Type
(2) S14: SOP-14
(3)Green Package
(3) G: Halogen Free and Lead Free
Packing
Tape Reel
MARKING

14 13
12
11
10
9
8
UTC
U74HCT73G
1
2
3
4
5
6
7
Date Code
Lot Code
www.unisonic.com.tw
Copyright © 2016 Unisonic Technologies Co., Ltd
1 of 6
QW-R126-047.A
U74HCT73
CMOS IC

PIN CONFIGURATION

FUNCTION TABLE
INPUT
OUTPUT
CLR
CLK
J
K
Q
Q
L
X
X
X
L
H
H
↓
L
L
Q0
Q0
H
↓
H
L
H
L
H
↓
L
H
L
H
H
↓
H
H
H
H
X
X
TOGGLE
Q0
Q0
Note: This configuration is unstable, as it is not persist when either PRE or CLR return to high level.

LOGIC DIAGRAM (positive logic)
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2 of 6
QW-R126-047.A
U74HCT73

CMOS IC
ABSOLUTE MAXIMUM RATING (Note 2)
PARAMETER
SYMBOL
CONDITIONS
RATINGS
UNIT
Supply Voltage
VCC
-0.5 ~ +7.0
V
Input Voltage
VIN
-0.5 ~ VCC+0.5
V
Output Voltage
VOUT
Active Mode
-0.5 ~ VCC+0.5
V
Continuous VCC or GND
ICC
±50
μA
Current
Continuous Output Current
IOUT
VOUT=0V ~ VCC
±25
mA
Input Clamp Current
IIK
VIN<0V or VIN>VCC
±20
mA
Output Clamp Current
IOK
VOUT>VCC or VOUT<0V
±20
mA
Storage Temperature Range
TSTG
-65 ~ +150
°C
Notes: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

RECOMMENDED OPERATING CONDITIONS
PARAMETER
Supply Voltage
Input Voltage
Output Voltage
Operating Temperature
Input Transition Rise or Fall
Rate

TEST CONDITIONS
MIN
4.5
0
0
-40
TYP
MAX
5.5
VCC
VCC
+85
UNIT
V
V
V
°C
500
ns
MAX
0.1
0.26
±0.1
UNIT
V
V
V
V
V
V
μA
4
μA
1.4
2.4
mA
3
10
pF
TYP
21
MAX
35
UNIT
ns
∆t/∆v
ELECTRICAL CHARACTERISTICS (TA =25°C , unless otherwise specified)
PARAMETER
High-level Input Voltage
Low-level Input Voltage
High-Level Output Voltage
Low-Level Output Voltage
Input Leakage Current
Quiescent Supply Current
Additional Quiescent Supply
Current Per Input Pin
Input Capacitance

SYMBOL
VCC
VIN
VOUT
TA
SYMBOL
TEST CONDITIONS
VIH
VCC=4.5V~5.5V
VIL
VCC=4.5V~5.5V
IOH=-20μA
VOH
VCC=4.5V
IOH=-4mA
IOL=20μA
VOL
VCC=4.5V
IOL=4mA
II(LEAK)
VCC=5.5V, VIN=VCC or GND
VCC=5.5V, VIN=VCC or GND,
ICC
IOUT=0V
∆ICC
CI
MIN
2
TYP
0.8
4.4
3.98
4.999
0.001
VCC=4.5V~5.5V, VIN=VCC-2.1V
VCC=4.5V~5.5V, VIN=VCC or GND
SWITCHING CHARACTERISTICS (CL=50pF, TA =25°C , unless otherwise specified)
PARAMETER
Propagation delay from input
( CLR ) to output (Q or Q )
Propagation delay from input
(CLK) to output (Q or Q )
SYMBOL
tPLH / tPHL
tPLH / tPHL
TEST CONDITIONS
VCC=4.5V
VCC=5.5V
17
31
ns
VCC=4.5V
20
28
ns
VCC=5.5V
18
25
ns
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
MIN
3 of 6
QW-R126-047.A
U74HCT73

CMOS IC
TIMING REQUIREMENTS (Input: tR, tF≤2.5ns; PRR≤1MHz)
PARAMETER
Clock frequency
SYMBOL
fCLOCK
Pulse duration
tW
Setup time before CLK↓
tSU
Hold time ,data after CLK↓
tH

Conditions
VCC=4.5V
VCC=5.5V
VCC=4.5V
VCC=5.5V
VCC=4.5V
VCC=5.5V
VCC=4.5V
VCC=5.5V
MIN
TYP
MAX
27
30
UNIT
MHZ
MHZ
ns
ns
ns
ns
ns
ns
TYP
MAX
UNIT
18
16
12
11
0
0
OPERATING CHARACTERISTICS (TA =25°C , unless otherwise specified)
PARAMETER
Power Dissipation
Capacitance
SYMBOL
CPD
TEST CONDITIONS
No load.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
MIN
35
pF
4 of 6
QW-R126-047.A
U74HCT73

CMOS IC
TEST CIRCUIT AND WAVEFORMS
Note: CL includes probe and jig capacitance. CL=50pF, RL=1KΩ.
Notes: 1. CL includes probe and jig capacitance.
2. All input pulses are supplied by generators having the following characteristics: PRR ≤10MHz, ZO = 50Ω.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 6
QW-R126-047.A
U74HCT73
CMOS IC
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
6 of 6
QW-R126-047.A