KNX-Intrusion Alarm System L240 Product Overview Contents The highest levels of security, comfort and cost-effectiveness 2 Efficiency in the installation through bus technology 3 The SafeKey setting device 4 Intrusion detection system example project, increased risk 5 System overview and engineering instructions 6 Product overview 8 2CDC 541 158 D0201 1 The highest levels of security, comfort and cost-effectiveness The Intrusion Alarm Panel L240 is the result of many years of experience in the security field and from three generations od intrusion alarm systems. This professional alarm system is designed for the integration into KNX installations for small to medium sized objects. The flexibility of the bus-based system and extendability of installation means that the same technology can be used for security applications in private residences as well as non-residential buildings. The alarm panel is operated using the Keypad L240/PT. It is also required when the panel is extended or messages are to be displayed in plain text. Thus, the panel complies with the requirements to VdS class C and to the European Standard EN 50131, Grade 3. The system can be extended to incorporate up to 80 detector circuits in different setting areas using external modules, which are simply connected to the Alarm Panel bus. Consequently, the panel provides an application spectrum ranging from private to commercial buildings and from the smallest to the largest insurance risks. Alarm Panel KNX Switch-Dim Actuator 2 2CDC 541 158 D0201 Fan/Fan Coil Actuator Blind Actuator LCD Keypad Efficiency in the installation through bus technology The Intrusion Alarm Panel L240 is simply extended by 4-wire connection of modules to the security bus (XIB). In addition to the Detector Circuit Modules L840/MG4 and L240/MG2, to which conventional detectors are connected, you can also connect BUS Motion Detectors with passive infrared and dual technology. The panel can be easily configured by PC via the serial Interface Module L208/V.24 or the LAN IP Interface L240/IP. Important events and access histories can also be read from the central memory in this way. The KNX interface from ABB offers a solution for the Intrusion Alarm System L240, which integrates professional security technology in KNX systems. All 80 detectors or detector circuits of the Intrusion Alarm System L240 are available as bi-directional communication objects on the KNX and/or on the intrusion alarm system. This allows security technology detectors to be used for other functions. So for example, opening a window will be detected by a window contact and signalled to the KNX system, which deactivates the room temperature controller. If however, no one is at home and the alarm system is triggered, this detector will trigger an alarm. Motion detectors can be used both for intrusion detection as well as for automatically switching on a light. If a sensor is used for 2 applications, fewer sensors are required, and if the heating is shut down, energy is also saved. But even more functions are possible: when opening a house door using SafeKey and KNX, for example, the required level of lighting and music can be switched on. Thus, many day-to-day routines can be automated in this way. XIB Sensors Bus Motion Detector SafeKey 2CDC 541 158 D0201 3 The SafeKey setting device …is simple and comfortable to operate Setting device and access control from a single source! Comfortable operation – optionally by numeric code, chipkey or a combination of both. The system is disarmed with just a single operation. Up to 8 Evaluation Modules can be connected via the XIB security bus to the Intrusion Alarm Panel L240. This facilitates the connection of the wall reader and assures communication with the panel. The keys are learned-in using a module in the panel and managed there via the keypad or by using the programming software WinPC. Every key can be assigned with different levels of authorization for each of the 8 doors, so that you can decide which key or person is permitted to set the intrusion alarm system. All locking actions together with the key name and the time of the action are registered in the event list memory of the panel and can be accessed on the keypad when required. 4 2CDC 541 158 D0201 …impresses with its elegant design SafeKey setting devices combine security and stylish ambiance. Security that is convincing – elegant design which impresses! Play it safe and select a design and appearance appropriate for your entrance or foyer. SafeKey and wall reader are available with a modern stainless-steel and matt chrome-plated finish. In the classic elegant design, they can be tastefully combined with every existing style. SafeKey chipkey Electronic chipkey for key operation and/or setting/unsetting. SafeKey chipkeys can be authorized for any number of different systems. Every chipkey is a unique read protected and copy protected device. SafeKey wall readers with and without keypad Remote input device for setting/ unsetting. The connection to the SafeKey Evaluation Module is wired. A bolt lock is required to ensure unavoidability compliance. …is absolutely flexible The user management of the Intrusion Alarm Panel manages the different authorization levels for each person on each door. New chipkeys and numeric codes are created in seconds; misplaced chipkeys can be quickly and easily deactivated without the laborious, cost-intensive task of replacing locking cylinders. Special highlight: A chipkey can be authorized for several SafeKey systems that are independent of one another. Intrusion detection system example project increased risk Motion detectors Flash Z ÜE Siren Magnet reed contact set Lock monitoring Keypad Z ÜE Panel Dialling device Setting device House example project, increased risk planning with L240 compliant to DIN VDE 0833. Parts list with wired technology Units Device Type 1 Intrusion Alarm Panel L240 2 Battery SAK7 If complete exterior surveillance is to be implemented, all windows must be 1 Keypad L240/PT monitored for opening with magnetic contacts to ensure lock monitoring 4 Motion Detectors IR/XB (either with VSUE or with blocking bolts). 2 (10) Magnetic Reed Contact Set MRS/W 2 Lock Bolt Switching Contact WRK/W (4) Blocking Bolt ADB 1 (5) 2 Zone Module L240/MG2 1 Combination Signalling Device SSF/GB 1 Siren SSF/G 1 Setting Device L240/BS in housing 1 Electric Bolt Lock All doors (here terrace doors) are to be monitored for opening and locking. with WEL or WELT ESPE 2CDC 541 158 D0201 5 System overview and engineering instructions Exterior surveillance What How With what Doors/ Opening Magnetic reed contacts windows Note Drill hole or flush mounted Connection to a distribution unit or zone module Breakage/ Passive or acoustic rupture glass break detectors Locking Strike plate contacts Installation in the strike plate. Lock monitoring Installation in the surround. for the windows Connection to the distribution unit or zone module. Only in conjunction with monitoring of opening. Interior monitoring What With what Motion in rooms Passive infrared detector Note Observe sources of interference! Heat and cold sources. Various effective ranges through exchangeable lenses. Dual detectors Observe sources of interference! Draughts, interfering transmitters. Fire/smoke Smoke alarm Gas Gas alarm Not in kitchen/bathroom/sauna. All combustible gasses Observe installation location! (light/heavy gasses) Water 6 2CDC 541 158 D0201 Water alarm Alarms What With what Internal Internal siren External local External siren with/without Note At least 3 m from the ground strobe light External silent Dialling device with voice A/B cable output Panel and accessories What Note Panel Installation location Batteries Consider the current consumption of the entire system Keypads At least one keypad Enhanced operation and programming: At least one L840/PT is necessary for all expansions and programming! Connection module for Also contains connections for MRS, WRK and ESPE; SafeKey situated beside the door. Detection circuit expansions L240/MG2: for connection of magnetic reed contact and glass break detectors (windows). L840/MG4; for connection of contact-relevant detectors. Remote programming via Serial port on the PC or LAN interface on the PC or Notebook via the network. Installation What Note Main distribution board For clearly arranged wiring to the panel. Junction boxes On windows, doors. Cable ducts From the door wing to frame. From door panel to frame (colour variants). Cables I-Y(ST) Y n x 0.6 or 0.8 mm 2CDC 541 158 D0201 7 Product range overview Overview Intrusion Alarm System L240 6 detector circuits, 1 PA, 1 tamper, 1 lock, 1 external set 1 Strobe Intrusion Alarm Panel L240 2 Sirens SAK 7 1 2 3 4 5 6 7 8 9 x 0 Up to 7 Keypads L240/PT SAK 7 XS/S 1.1 IR/X... max. 40 devices Intrusion Alarm Panel L240 with bus technology is the universal solution for all applications. The following bus modules can be connected to the panel: 2 Zone Modules L240/MG2 for connection to the exterior perimeter detectors such as magnetic reed contacts and passive glass break sensors. The module has 2 zones, to which 2 detectors can be connected via LSA terminals. The module is an intelligent distributor by simple installation in a 60 mm installation box in the vicinity of the window. Zone Module L840/MG4 for expansion of the panel by up to 4 detector circuits. A SAD enclosure is required. L240/MG2 max. 24 devices L840/MG4 max. 16 devices L240/BS max. 8 devices SafeKey Evaluation Module L240/BS for connection of the SafeKey components as well as all components required for a setting door (magnetic contacts, lock bolt switching contact, bolt lock, internal siren). The management of the electronic keys from the SafeKey range is undertaken completely on the LCD keypad of the panel. In total, 80 detectors or detector circuits (zones) (10 groups to the panel and a further 70 on the bus). Furthermore, up to 8 x L240/BS – a total of 8 doors – can be connected, and 4 setting zones can be formed. The interface to KNX facilitates complete integration of the security functions into the KNX system, up to VdS class C. Interface Module L240/IP for programming of the L240 via PC, incl. WinPC software. Risk allocation, classification Optional system accessories • • • • • • • • • • • VdS approved as an Intrusion Alarm Panel for VdS classes A, B, C Corresponds to DIN VDE 0833 parts 1 & 3 Grade 3 according to European standard EN 50131-1 “medium to high risk” Typical areas of application Residential and commercial properties with more than one security zone, commercial zones up to stage 6, and banks with an insurance company/police requirement for a medium to high risk alarm system Application limitations: • The Intrusion Alarm Panel is suitable for all types of risk • The limits of the application are only in the scale of the system (number of detector zones) • The Intrusion Alarm Panel is suitable for up to four setting zones Max. 7 Keypads L240/PT Max. 2 Batteries SAK7 8 SafeKey Evaluation Modules L240/BS Zone Modules L240/MG2 and/or L840/MG4 1 Serial Interface L208/V.24 1 Ethernet Interface L240/IP Supplementary Power Supply L240/N KNX Interface XS/S 1.1 Suitable alarm equipment • • • Internal siren for occupancy alarm: 1 SSS External siren/strobe: 1 SSF/G and 1 SSF/GB Silent alarm: Local devices Degree of expansion Suitable setting devices • • • • • 4 setting zones 80 programmable inputs Motion detectors can be connected to the bus Window contacts and glass break sensors can be connected to the bus via the Bus Module L240/MG2 The panel can be extended with up to 8 SafeKey Evaluation Modules L240/BS and Zone Modules L240/MG2 and/or L840/MG4. Internal setting via Keypad L240/PT External setting • • Via Keypad L240/PT delayed in the security zone With SafeKey components on L240/BS up to 8 doors Suitable sensors Obligatory system accessories • • 1 Battery SAK7 1 Keypad L240/PT per setting zone 8 2CDC 541 158 D0201 All detectors and contacts from the ABB intrusion alarm range. The total current consumption must be observed. Type Detail Order code PG MB Type Detail Order code Intrusion Alarm Panel Sealed Lead Acid Battery, 12 V DC, 7 Ah For residential and commercial properties with more For Intrusion Alarm Panel emergency power. than one security zone, commercial zones up to 2 units can be installed. VdS class C. PG MB stage 6, and banks with an insurance company/ police requirement for a medium to high risk alarm SAK7 GH V924 0001 V0011 50 - system. VdS approved as an Intrusion Alarm Panel for BUS-IR Motion Detector VdS classes A, B, C. For direct connection to the bus of the Intrusion Alarm Corresponds to DIN VDE 0833 parts 1 & 3, Stage Panel L240, whereby a maximum of 40 detectors can 3 according to European standard EN 50131-1 be addressed by the panel. “medium to high risk”. The motion detectors with passive infrared technology are registered for VdS classes B and C (anti-masking L240/ENG English monitored). They facilitate monitoring of an area with 2CDG 230 017 R0011 50 - an IR range of up to 15 m. Interface for Intrusion Alarm Panel, MDRC Integration into KNX systems is possible using the IR/XB VdS class B 2CDG 230 023 R0011 50 - Interface XS/S1.1. IR/XC VdS class C 2CDG 230 024 R0011 50 - Accordingly, there are numerous benefits: MW Mounting Bracket GH V923 0039 V0020 50 - For example, a door/window opening detector can be used to switch off the heating and save energy in BUS Dual Motion Detector the unset state. When an alarm is triggered, the KNX For direct connection to the bus of the Intrusion Alarm devices can carry out actions such as switching on Panel L240, whereby a maximum of 40 detectors the light or operating the blinds. can be addressed by the panel. The interaction offers further benefits in terms of The Dual-Motion Detector combines proven passive system integration, which comply to the demands of infrared technology with temperature-independent the VdS up to class C. microwave technology. The combination of both functional principles results in a detector featuring XS/S 1.1 high immunity to false alarms, even with unfavourable 2CDG 110 075 R0011 26 - ambient conditions, and which still has high detection LCD Keypad security. The detectors are registered for VdS classes For operation and programming of the panel. B and C (anti-masking monitored). They facilitate The messages are displayed on a two-line LCD monitoring of an area with an IR range of up to 15 m. display. Menu driven operation and programming of the panel. Internal and external setting on the keypad EIM/XB VdS class B 2CDG 230 025 R0011 50 - is possible. VdS class C. EIM/XC VdS class C 2CDG 230 026 R0011 50 - MW Mounting Bracket GH V923 0039 V0020 50 - L240/PT 2CDG 230 014 R0011 50 Zone Bus-Module, 2-fold Serial Interface Module For expansion of the panel by 2 detector circuits. For programming of the L240 via PC with Used for connection to the exterior perimeter serial interface V24, incl. WinPC software. detectors such as magnetic reed contacts and passive glass break sensors. The module has L208/V.24 2 zones, to which 2 detectors can be connected via GH Q328 0220 R0001 50 - LSA terminals. The module is an intelligent distributor IP Interface Module by simple installation in a 60 mm installation box For programming of the L240 via PC with in the vicinity of the window. Ethernet interface, incl. WinPC software. L240/MG2 L240/IP 2CDG 220 003 R0011 50 - 2CDG 230 013 R0011 50 Zone Bus-Module, 4-fold For expansion of the panel by 4 detector circuits. A SAD enclosure is required for installation. L840/MG4 GH Q328 0011 R0001 50 - 2CDC 541 158 D0201 9 Type Detail Order code PG MB Type Detail Order code SafeKey Wall Reader Distribution Enclosure For setting/unsetting with the Evaluation Module For installation of the Bus Modules L840/MG4 L240/BS. The unit is actuated by inserting the and L240/BS. PG MB electronic SafeKey chipkey. The SafeKey Wall Reader WEL is equipped with the key reader and SAD/GAP Surface mounting GH Q328 0015 R0001 50 - SAD/GUP Flush mounting GH Q328 0013 R0001 50 - SAD/ED Wall box for GH Q328 0014 R0001 50 - an acknowledgement buzzer. VdS class C. WEL/A,ES Stainless steel GH Q305 0023 R0001 53 - SAD/GUP SafeKey Wall Reader with Keypad For setting/unsetting with the Evaluation Module Security Terminal, 4-fold, MDRC L240/BS. The unit is actuated by inserting the is used for the monitored connection of sensors from electronic SafeKey chipkey and/or by a code keypad. security technology (e.g. magnetic contacts or glass- The SafeKey Wall Reader WELT is equipped with the breakage sensors) to the ABB i-bus® KNX. The device key reader, an acknowledgement buzzer and a code has four inputs (“zones”) available and can be used keypad. as a stand-alone security system or in combination VdS class C. with the security module or control panel with KNX interface. 12 V DC SELV power supply required, e.g. WELT/A,ES Stainless steel GH Q305 0024 R0001 53 - NTU/S 12.2000.1. Typical applications are door and WELT/A,MC Matt chrome-plated GH Q305 0024 R0011 53 - window surveillance, glas-breakage detection as well as area surveillance. SafeKey Chipkey It is an electronic carrier medium for lock actuation MT/S 4.12.2M 2CDG 110 109 R0011 26 - and for setting/unsetting on a strike plate, door cylinder or wall reader. A SafeKey Chipkey can be Security Terminal, 8-fold, MDRC authorized for any number of different SafeKey is used for the monitored connection of sensors from systems with different levels of authorization. security technology (e.g. magnetic contacts or glassbreakage sensors) to the ABB i-bus® KNX. The device SCS has eight inputs (“zones”) available and can be used GH Q305 0027 R0001 53 - as a stand-alone security system or in combination SafeKey Evaluation Module with the security module or control panel with KNX For connection of the SafeKey components as well interface. 12 V DC SELV power supply required, e.g. as all components required for a setting door NTU/S 12.2000.1. Typical applications are door and (magnetic contacts, lock bolt switching contact, window surveillance, glas-breakage detection as well bolt lock, internal siren). The management of the as area surveillance. electronic keys from the SafeKey range is undertaken completely on the LCD keypad of the panel. L240/BS MT/S 8.12.2M GH Q305 0031 R0001 53 - 2CDG 110 110 R0011 26 Security Terminal, 2-fold, FM is used for the monitored connection of sensors from Electromechanical Bolt Lock security technology (e.g. magnetic contacts or glass- Prevents access to the set zone of an Intrusion Alarm breakage sensors) to the ABB i-bus® KNX. The device Panel. has two inputs (“zones”) available and can be used The unit is mounted in the door frame. Only a single as a stand-alone security system or in combination bore or the counterpart for the locking bolt in the with the security module or control panel with KNX door panel is required. Suitable for use with WEL and interface. 12 V DC SELV power supply required, e.g. WELT. VdS class C. NTU/S 12.2000.1. Typical applications are door and window surveillance, glas-breakage detection as well ESPE EVSB Replacement Locking GH V925 0010 V0002 50 MT/U 2.12.2 Bolt AMSP Mounting kit, flat door GH V925 0010 V0004 50 - panel and frame AMSE as area surveillance. GH V925 0010 V0001 50 - Mounting kit, raised door panel 10 2CDC 541 158 D0201 GH V925 0010 V0003 50 - 2CDG 110 111 R0011 26 - Type Detail Order code PG MB Type Detail Order code PG MB Magnet Reed Contact Set Lock Bolt Switching Contact For opening surveillance of windows and doors, For installation in the strike plate, for lock monitoring complete for bolting or drilling on doors. Contents: 1 magnet, 1 reed contact with 4.0 m Water-tight IP 67, with 2.5 m connection cable connection cable LIYY 4 x 0.14 mm2, 2 housings, LIYY 3 x 0.14 mm2. VdS class C. 3 spacer plates, 2 flanges and 4 anti-magnetic fixing screws. VdS class B. WRK/W 2CDG 250 003 R0011 50 - MRS/W White GH Q320 1972 R0001 50 - Window Opening Plunger MRS/B Brown GH Q320 1972 R0002 50 - Lock monitoring is carried out with a special magnet and a reed contact. Magnet Reed Contact Saver Set The magnet is mounted on the push rod of the For opening surveillance of windows and doors, window sash, while the reed contact is mounted on complete for bolting or drilling. the frame. Contents: 20 magnets, 20 reed contacts with 4.0 m connection cable LIYY 4 x 0.14 mm2, 40 housings, The connection cable LIYY 4 x 0.14 mm2 is 4 m 60 spacer plates, 40 flanges and 80 anti-magnetic in length. VdS class C. fixing screws. VdS class B. VSUE VMRS/W White GH Q320 1972 R0011 50 - VMRS/B Brown GH Q320 1972 R0012 50 - GH V921 0018 V0022 50 Blocking Bolt Indirect lock monitoring by mechanical push opening Rolling Door Magnet Reed Contact Set of the window in conjunction with magnetic contacts For monitoring opening or rolling doors or other large that monitor opening. doors in the industrial field. Available in 2 spring strengths. Contents: 1 magnet, 1 reed contact with 2 m connection cable 4 x 0.14 mm2, 1 m protective tubing ADB 150 N GH V921 0018 V0020 50 - and 1 set of mounting accessories. ADB1 35 N GH V921 0018 V0021 50 - Dimensions: H x W x D = Reed contact 159 x 50 x 19 mm; Emergency Call Button magnet 100 x 40 x 35 mm; degree of protection: For manual alarm tripping. Complies with Police IP 68; Environmental class to VdS 4; VdS class B. regulations, since it features permanent trip recognition, momentary-contact function, with cover RTK contact. GH Q320 1973 R0021 50 - Available in surface mount and flush mount versions. Glass Break Sensor, passive The cover plate is used primarily in the banking For surveillance of glass surfaces of windows, display sector or other institutions, where unintentional alarm windows and doors with high interference immunity triggering is possible due to public access. and integrated memory display. Colour: white. VdS class C. For operation directly on detector circuits of Intrusion Alarm Panels or Zone Terminals. ND/W Surface mounting GH Q713 2443 R0011 50 - Extremely compact dimensions. NDU/W Flush mounting GH Q713 2443 R0021 50 - Dimensions: H x W x D = 18 x 18 x 9 mm. EP Spare Papers (10 pcs.) GH Q713 2443 R0003 50 - Mounted onto glass using Loctite Adhesive (LKS). NDA/W Cover plate GH Q713 2443 R0004 50 - With 5 m connection cable. VdS class B. SPGS/W White GH V922 0004 V0009 50 - SPGS/B Brown GH V922 0004 V0010 50 - GP2 Mechanical Glass GH V922 0004 V0004 50 - Break Test Device LKS Loctite Adhesive GH Q400 1906 R0001 50 - 2CDC 541 158 D0201 11 Type Detail Order code PG MB Type Detail Order code PG MB Gas Detector Electronic Solid-State Siren For measurement and evaluation of the concentra- Electronic solid-state siren with intermittent tone for tion of natural gas or liquefied gas in the air. The alarm purposes in indoor installations. detector requires a (10 – 30 V DC) voltage supply and External dimensions: ø x H = 90 x 37 mm. has a normally open floating relay output contact for connection to the Intrusion Alarm Panels, features an SSS GH V927 0001 V0001 50 - LED display and a Piezo buzzer. For ceiling and wall Combination Signalling Device mounting. Siren in an aluminium protective housing with SGL GH Q305 0008 R0001 50 - additional protective enamel coating. Protected against sabotage by a case tamper contact. The Water Detector alarm inputs are wired onto a terminal strip. A resin-encapsulated water detector with gold- Dimensions: H x W x D = 200 x 205 x 88 mm plated Termipoint pins, detects water ingress, e.g., pipe fractures, ingress of groundwater and sewage, Strobe light mounted on top. water damage caused by washing machines and Dimensions: H x W x D = 258 x 205 x 88 mm dishwashers etc., before the damage becomes too Colour RAL 9002. VdS class C. expensive. For operation directly on detector circuits of Intrusion Alarm Panels or Zone Terminals. SWM4 GH Q403 0001 R0004 50 Smoke Detector For early detection of fire in buildings. The VdS certified detector can be connected to 12 V intruder zones with the detector base. A floating two-way contact serves as an alarm output. An optional reed relay in the last detector of the zone monitors the supply voltage and the removal of a smoke detector from the base. For testing the detector, a testing aerosol or a remote test unit can be used. FC600/O Optical Smoke 2CDG 430 047 R0011 52 - Detector FC600/TMAX Optical/Thermal 2CDG 430 049 R0011 52 - Detector FC600/BREL Detector Base, 12 V 2CDG 430 051 R0011 52 - FPA03 Testing Aerosol, 250 ml GH V902 0012 V0021 52 - RL Reed Relay, 12 V GH V927 0013 V0100 50 - 12 2CDC 541 158 D0201 SSF/G Without strobe light GH Q305 0017 R0001 50 - SSF/GB With strobe light GH Q305 0018 R0001 50 - Your ABB partner Note: We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB AG does not accept any responsibility whatsoever for potential errors or possible lack of information in this document. We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents - in whole or in parts - is forbidden without prior written consent of ABB AG. Copyright© 2010 ABB All rights reserved www.abb.com/knx Order Number 2CDC 541 158 D0201 printed in Germany (06/10-0.2-ZVD) Contact