VDMR10A1, VDMO10A1, VDMY10A1, VDMG10A1 www.vishay.com Vishay Semiconductors Standard 7-Segment SMD Display 10 mm FEATURES • Evenly lighted segments • Grey package surface • Untinted segments • Luminous intensity categorized • Yellow, green, and soft orange categorized for color • Wide viewing angle • Suitable for DC and high peak current DESCRIPTION The VDM.10A1 series are 10 mm SMD seven segment LED displays in a very compact package. The devices utilize AlInGaP on GaAs chip technology. • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • Panel meters PRODUCT GROUP AND PACKAGE DATA • Test- and measure-equipment • Product group: Display • Point-of-sale terminals • Package: 10 mm • Control units • Product series: SMD • Angle of half intensity: ± 50° PARTS TABLE PART COLOR LUMINOUS INTENSITY (μcd) MIN. TYP. MAX. WAVELENGTH at at FORWARD VOLTAGE at (nm) (V) IF IF IF (mA) MIN. TYP. MAX. (mA) MIN. TYP. MAX. (mA) CIRCUITRY VDMR10A1 Super red 450 1600 - 1 - 631 - 20 - 2.0 2.6 20 Common anode VDMO10A1 Soft orange 180 650 - 1 - 605 - 20 - 2.0 2.6 20 Common anode VDMY10A1 Yellow 450 1600 - 1 - 587 - 20 - 2.0 2.6 20 Common anode VDMG10A1 Green 110 500 - 1 - 572 - 20 - 2.0 2.6 20 Common anode ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) VDMR10A1, VDMO10A1, VDMY10A1, VDMG10A1 PARAMETER TEST CONDITION SYMBOL VALUE UNIT Power dissipation per segment PV 70 mW Peak forward current per segment (frequency 1 kHz, 10 % duty cycle) IF 60 mA Continous forward current per segment IF Forward current derating from 25 °C 25 mA 0.28 mA/°C Operating temperature range Tamb -35 to +105 °C Storage temperature range Tstg -35 to +105 °C Iron soldering conditions: 1/16" below seating plane for 3 s at 260 °C Rev. 1.2, 29-Nov-13 Document Number: 84197 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VDMR10A1, VDMO10A1, VDMY10A1, VDMG10A1 www.vishay.com Vishay Semiconductors OPTICAL AND ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) VDMR10A1, SUPER RED PARAMETER Luminous intensity (1) TEST CONDITION PART SYMBOL MIN. TYP. MAX. IF = 1 mA VDMR10A1 IV 450 1600 - UNIT μcd IF = 10 mA VDMR10A1 IV - 20 800 - μcd Dominant wavelength IF = 20 mA λd - 631 - nm Peak emmision wavelength IF = 20 mA λp - 639 - nm Spectral line half-width IF = 20 mA Δλ - 20 - Forward voltage per segment IF = 20 mA Reverse current per segment (2) Luminous intensity matching ratio VDMR10A1 VF - 2.0 2.6 V VR = 5 V IR - - 100 μA IF = 10 mA Iv-m - - 2:1 Notes (1) Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. (2) Reverse voltage is only for IR test.It can not continue to operate at this situation. (3) Cross talk specification ≤ 2.5 %. OPTICAL AND ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) VDMO10A1, SOFT ORANGE PARAMETER Luminous intensity (1) TEST CONDITION PART SYMBOL MIN. TYP. MAX. IF = 1 mA VDMO10A1 IV 180 650 - UNIT μcd IF = 10 mA VDMO10A1 IV - 8250 - μcd Dominant wavelength IF = 20 mA λd - 605 - nm Peak emmision wavelength IF = 20 mA λp - 611 - nm Spectral line half-width IF = 20 mA Δλ - 17 - Forward voltage per segment IF = 20 mA Reverse current per segment (2) Luminous intensity matching ratio VDMO10A1 VF - 2.0 2.6 V VR = 5 V IR - - 100 μA IF = 10 mA Iv-m - - 2:1 Notes (1) Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. (2) Reverse voltage is only for IR test.It can not continue to operate at this situation. (3) Cross talk specification ≤ 2.5 %. OPTICAL AND ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) VDMY10A1, YELLOW PARAMETER Luminous intensity (1) TEST CONDITION PART SYMBOL MIN. TYP. MAX. IF = 1 mA VDMY10A1 IV 450 1600 - UNIT μcd IF = 10 mA VDMY10A1 IV - 17 600 - μcd Dominant wavelength IF = 20 mA λd - 587 - nm Peak emmision wavelength IF = 20 mA λp - 588 - nm Spectral line half-width IF = 20 mA Δλ - 15 - Forward voltage per segment IF = 20 mA Reverse current per segment (2) Luminous intensity matching ratio VDMY10A1 VF - 2.0 2.6 V VR = 5 V IR - - 100 μA IF = 10 mA Iv-m - - 2:1 Notes (1) Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. (2) Reverse voltage is only for IR test.It can not continue to operate at this situation. (3) Cross talk specification ≤ 2.5 %. Rev. 1.2, 29-Nov-13 Document Number: 84197 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VDMR10A1, VDMO10A1, VDMY10A1, VDMG10A1 www.vishay.com Vishay Semiconductors OPTICAL AND ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) VDMG10A1, GREEN PARAMETER Luminous intensity (1) TEST CONDITION PART SYMBOL MIN. TYP. MAX. IF = 1 mA VDMG10A1 IV 110 500 - UNIT μcd IF = 10 mA VDMG10A1 IV - 5500 - μcd Dominant wavelength IF = 20 mA λd - 572 - nm Peak emmision wavelength IF = 20 mA λp - 571 - nm Spectral line half-width IF = 20 mA Δλ - 15 - Forward voltage per segment IF = 20 mA Reverse current per segment (2) Luminous intensity matching ratio VDMG10A1 VF - 2.0 2.6 V VR = 5 V IR - - 100 μA IF = 10 mA Iv-m - - 2:1 Notes (1) Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. (2) Reverse voltage is only for IR test.It can not continue to operate at this situation. (3) Cross talk specification ≤ 2.5 %. LUMINOUS INTENSITY CLASSIFICATION GROUP LIGHT INTENSITY (μcd) COLOR CLASSIFICATION GROUP SOFT ORANGE YELLOW GREEN MIN. MAX. MIN. MAX. MIN. MAX. 1 598 601 581 584 - - 360 2 600 603 583 586 - - 560 3 602 605 585 588 562 565 450 900 4 604 607 587 590 564 567 700 1400 5 606 609 589 592 566 569 I 1100 2200 6 608 611 591 594 568 571 K 1800 3600 7 - - - - 570 573 L 2800 5600 8 - - - - 572 575 M 4500 9000 STANDARD MIN. MAX. D 110 220 E 180 F 280 G H N 7000 14 000 P 11 000 22 000 Q 18 000 36 000 R 28 000 56 000 S 45 000 90 000 Note • Wavelengths are tested at a current pulse duration of 25 ms. Note • The above type numbers represent the order groups which include only a few brightness groups. Only one group will be shipped in one tube (there will be no mixing of two groups in one tube). In order to ensure availability, single brightness groups will not be orderable. Rev. 1.2, 29-Nov-13 Document Number: 84197 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VDMR10A1, VDMO10A1, VDMY10A1, VDMG10A1 www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 100 I F - Forward Current (mA) IF - Forward Current (mA) 30 25 20 15 10 10 5 0 0 20 40 60 80 100 1 1.0 120 Tamb - Ambient Temperature (°C) green 2.5 3.0 3.5 Fig. 4 - Forward Current vs. Forward Voltage 100 yellow soft orange super red Ipeak - Peak Current (mA) 1.0 Irel - Relative Intensity 2.0 V F - Forward Voltage (V) Fig. 1 - Forward Current vs. Ambient Temperature 1.2 1.5 0.8 0.6 0.4 0.2 0 520 540 560 580 600 620 640 660 680 λ - Wavelength (nm) Fig. 2 - Relative Intensity vs. Wavelength 10 1 10 100 Duty Cycle % (Frequency 1 kHz) Fig. 5 - Peak Current vs. Duty Cycle I v rel - Relative Luminous Intensity (normalized to 1 at 10 mA) 3.0 2.5 2.0 1.5 1.0 0.5 0 0 5 10 15 20 25 30 I F - Forward Current (mA) Fig. 3 - Relative Luminous Intensity vs. Forward Current Rev. 1.2, 29-Nov-13 Document Number: 84197 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VDMR10A1, VDMO10A1, VDMY10A1, VDMG10A1 www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 9.8 10 0.6 6 10 6 Ø1.7 Ø1.2 5.15 10 16 13 5.15 Ø1.7 1.5 ±0.1 3.65 3.66 1.9 2.1 6. 2 1. 2 Ø1.55 Ø1.4 1 10° 5 5 R0.65 1 3.7 1.84 Plastic pins’ burr max. 0.14 mm 3, 8 A F G E B A B C D E F G DP C D DP 7 6 4 2 1 9 10 5 Connection No. Cathode E 1 Cathode D 2 3 Common Anode Cathode C 4 5 Cathode DP Cathode B 6 Cathode A 7 8 Common Anode Cathode F 9 Cathode G 10 Tolerances are ± 0.25 mm unless otherwise mentioned technical drawings according to DIN specifications Drawing-No.: 6.544-5426.01-4 Issue: 2; 02.10.13 Rev. 1.2, 29-Nov-13 Document Number: 84197 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VDMR10A1, VDMO10A1, VDMY10A1, VDMG10A1 www.vishay.com Vishay Semiconductors TAPE AND REEL DIMENSIONS in millimeters TAPE IN BOX Rev. 1.2, 29-Nov-13 Document Number: 84197 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VDMR10A1, VDMO10A1, VDMY10A1, VDMG10A1 www.vishay.com Vishay Semiconductors BAR CODE PRODUCT LABEL (example only) RECOMMENDED SOLDER PAD 4 x 1.9 = 7.6 A 3 B C D L E I G F H M K 2D barcode Vishay part number Quantity PTC = selection code (binning) Code of manufacturing plant Batch = date code: year/week/plant code Region code SL = sales location Terminations finishing Lead (Pb)-free symbol Halogen-free symbol RoHS symbol 15 A) B) C) D) E) F) G) H) I) K) L) M) 1.65 MSL LABEL SOLDERING PROFILE IR Reflow Soldering Profile for lead (Pb)-free Soldering Preconditioning acc. to JEDEC Level 3 300 Temperature (°C) max. 260 °C 245 °C 255 255 °C 240 °C 217 °C 250 200 max. 30 s 150 max. 100 s max. 120 s 100 max. Ramp Up 3 °C/s 50 max. Ramp Down 6 °C/s 0 0 50 19470-5 100 150 Time (s) 200 250 300 max. 2 cycles allowed Fig. 6 - Vishay Lead (Pb)-free Reflow Soldering Profile (acc. to J-STD-020C) SOLDERING IRON (one time only) Temperature Soldering time Rev. 1.2, 29-Nov-13 300 °C max. 3 s max. Document Number: 84197 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000