SBN1661G

DATA SHEET
SBN1661G_M18,
SBN1661G_M02,
SBN0080G_S18,
SBN0080G_S02
Dot-matrix STN LCD Driver
with 32-row x 80-column
Display Data Memory
To improve design and/or performance,
Avant Electronics may make changes to its
products. Please contact Avant Electronics
for the latest versions of its products
Data Sheet (V6.5A)
2007 Jul 05
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
1
GENERAL
1.1
Description
The SBN1661G_X is a series of STN LCD SEGMENT/COMMON drivers. The series has four members:
• the SBN1661G_M18,
• the SBN1661G_M02,
• the SBN0080G_S18, and
• the SBN0080G_S02.
Both the SBN1661G_M18 and the SBN1661G_M02 can drive 16 COMMONs and 61 SEGMENTs and can be used as
master in a master-slave connection. They both have 32-row x 80-column Display Data Memory. Functionally, their only
difference is that the SBN1661G_M18 has an on-chip RC-type oscillator and can provide clock to slave, while the
SBN1661G_M02 does not have an on-chip oscillator and needs external clock source.
Both the SBN0080G_S18 and the SBN0080G_S02 are purely SEGMENT drivers. They do not have COMMON outputs
and are used for segment expansion in a master-slave connection. Both devices need either a master or an external
clock source to provide clock. The only difference between these two chips is their operating frequency. The
SBN0080G_S18’s operating frequency is 18 KHz, while the SBN0080G_S02’s operating frequency is 2KHz.
All four devices have on-chip Display Data Memory of 32-rows x 80-columns, for storing display data. Dot-matrix mapping
method is used to drive the LCD panel. Therefore, a bit of the Display Data Memory corresponds to a pixel on the LCD
panel. SEGMENT drivers provide display data to the LCD panel and COMMON drivers provide row-scanning signal.
All four devices have a set of internal registers. These internal registers must be properly programmed to ensure proper
operation of the devices.
Display on the LCD panel is controlled by a host microcontroller. All four devices communicate with the host
microcontroller via data bus and control bus. The data bus is 8-bit wide. The control bus are READ, WRITE, and
Chip Select. The host microcontroller can perform READ/WRITE operations to the internal registers and Display Data
RAM of all four devices. A wide variety of microcontrollers can easily interface with the devices, as the devices can accept
both 80-type interface timing and 68-type interface timing. The selection of interface timing is via the dual-function
RESET/IF pin.
2007 Jul 05
2 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
1.2
Features
• Four members of the SBN1661G_X series:
– the SBN1661G_M18,
– the SBN1661G_M02,
– the SBN0080G_S18, and
– the SBN0080G_S02
• 16 COMMON, 61 SEGMENT STN LCD driver (the SBN1661G_M18 and the SBN1661G_M02).
• 80 SEGMENT STN LCD driver for expanding segment number (the SBN0080G_S18 and the SBN0080G_S02).
• On-chip Display Data Memory: 32-row x 80-column (totally 2560 bits).
• Dot Matrix Mapping between the Display Data Memory bit and LCD pixel.
• A “0” stored in the Display Data Memory bit corresponds to an OFF-pixel on the LCD panel; a “1” stored in the Display
Data Memory bit corresponds to an ON-pixel on the LCD panel.
• 5-level external LCD bias.
• Display duty cycle: 1/16, 1/32 for all four devices.
• Two types of interface timing with a host microcontroller: the 80-type microcontroller and the 68-type microcontroller.
• Dual function RESET/IF input for chip reset and selection of microcontroller interface timing.
• 8-bit parrallel data bus; READ, WRITE, CHIP SELECT control bus.
• A set of internal registers: Display ON/OFF, Display Start Line, Static Drive ON/OFF, Memory Page Address, Memory
Column Address, Duty Selection, Memory Column/Segment mapping, and Status.
• Display Data Read/Write commands and Software Reset command.
• Read-Modify-Write command for block data transfer from the host microcontroller to the Display Data Memory.
• Power-saving mode.
• On-chip RC-type oscillator, requiring only an external resistor (the SBN1661G_M18).
• Operating voltage range (VDD): 2.7 ~ 5.5 volts.
• LCD bias voltage (VLCD=V5-VDD): -13 volts (max.).
• Operating frequency range: 2 KHz, 18 KHz.
• Operating temperature range: -20 to +75 °C.
• Storage temperature range: -55 to +125 °C.
2007 Jul 05
3 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
1.3
Ordering information
Table 1
Product types
Product Name
SBN1661G_M18
Clock frequency
on-chip
External
18 KHz
18 KHz
SBN1661G_M02
2 KHz
SBN0080G_S18
18 KHz
SBN0080G_S02
2 KHz
Table 2
Number of
segment driver
Number of
common driver
61
16
80
0
duty cycle
1/16, 1/32
Ordering information
PRODUCT TYPE
DESCRIPTION
SBN1661G_M18-LQFPG
LQFP100 Pb-free package.
SBN1661G_M18-QFPG
QFP100 Pb-free package.
SBN1661G_M18-LQFP
LQFP100 general package.
SBN1661G_M18-QFP
QFP100 general package.
SBN1661G_M18-D
tested die.
SBN1661G_M02-LQFPG
LQFP100 Pb-free package.
SBN1661G_M02-QFPG
QFP100 Pb-free package.
SBN1661G_M02-LQFP
LQFP100 general package.
SBN1661G_M02-QFP
QFP100 general package.
SBN1661G_M02-D
tested die.
SBN0080G_S18-LQFPG
LQFP100 Pb-free package.
SBN0080G_S18-QFPG
QFP100 Pb-free package.
SBN0080G_S18-LQFP
LQFP100 general package.
SBN0080G_S18-QFP
QFP100 general package.
SBN0080G_S18-D
tested die.
SBN0080G_S02-LQFPG
LQFP100 Pb-free package.
SBN0080G_S02-QFPG
QFP100 Pb-free package.
SBN0080G_S02-LQFP
LQFP100 general package.
SBN0080G_S02-QFP
QFP100 general package.
SBN0080G_S02-D
tested die.
2007 Jul 05
4 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
FUNCTIONAL BLOCK DIAGRAM AND DESCRIPTION
V5
V4
V3
SEG0
SEG1
SEG59
COM1
SEG60
Funtional block diagram (SBN1661G_M18, SBN1661G_M02)
COM15
2.1
COM0
2
Output Driver
Level Shifter
V2
V1
High Voltage Circuit
MUX
Display
Control
Time Gen.
Mapping Circuit
COMMON Counter
C/S Mappig Register
Display Data RAM Buffer
Display ON/OFF Register
Display Start Line Register
32 row x 80 column
(2560 bits)
Display Data RAM
Line Address
Decoder
Page Address Register
Column Address Register
Status Register
Duty Select Register
Column Address Decoder
Static Drive ON/OFF
Register
Display Data RAM Access Control
Command
Decoder
Display Data
Read/Write
Control
Display
Control
OSC2(CL)
OSC1(CS)
FR
M/S
OSC and
Timing Gen.
RESET/IF
R/W(WR)
E/RD
C/D
DB0~DB7
Microcontroller
Interface
Fig.1 Functional Block Diagram
2007 Jul 05
5 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
3
PIN(PAD) ASSIGNMENT, PAD COORDINATES, SIGNAL DESCRIPTION
The SBN1661G_M18 and SBN1661G_M02 pinning diagram (LQFP100)
DB1
DB0
VSS
R/W(WR)
E/RD
OSC2(CL)
OSC1(CS)
C/D
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
3.1
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
DB2
DB3
DB4
DB5
DB6
DB7
VDD
RESET/IF
FR
V5
V3
V2
M/S
V4
V1
COM0
COM1
COM2
COM3
COM4
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
SBN1661G_M18
SBN1661G_M02
(Master/Slave Driver)
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41
COM5
COM6
COM7
COM8
COM9
COM10
COM11
COM12
COM13
COM14
COM15
SEG60
SEG59
SEG58
SEG57
SEG56
SEG55
SEG54
SEG53
SEG52
SEG51
SEG50
SEG49
SEG48
SEG47
SEG46
SEG45
SEG44
SEG43
SEG42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Note:
(1) For the SBN1661G_M18, pin 74 is OSC1 and pin 75 is OSC2.
(2) For the SBN1661G_M02, pin 74 is CS and pin 75 is CL.
(3) All other pins of both devices have the same pin(pad) assignment.
(4) Both devices can be used as master or slave, by setting their M/S pin.
Fig.2 The SBN1661G_M18 , the SBN1661G_M02 pin assignment of LQFP100 package.
2007 Jul 05
6 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
The SBN0080G_S18, the SBN0080G_S02 pinning diagram (LQFP100)
DB1
DB0
VSS
R/W(WR)
E/RD
CL
CS
C/D
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
3.2
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
DB2
DB3
DB4
DB5
DB6
DB7
VDD
RESET/IF
FR
V5
V3
V2
SEG79
SEG78
SEG77
SEG76
SEG75
SEG74
SEG73
SEG72
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
SBN0080G_S18
SBN0080G_S02
(Slave Segment Driver)
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41
SEG71
SEG70
SEG69
SEG68
SEG67
SEG66
SEG65
SEG64
SEG63
SEG62
SEG61
SEG60
SEG59
SEG58
SEG57
SEG56
SEG55
SEG54
SEG53
SEG52
SEG51
SEG50
SEG49
SEG48
SEG47
SEG46
SEG45
SEG44
SEG43
SEG42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Note:
(1) Both devices have the same pin(pad) assignment.
(2) Both devices can be used only as Slave Segment Driver.
Fig.3 The SBN0080G_S18, the SBN0080G_S02 pin assignment of LQFP100 package.
2007 Jul 05
7 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
51 SEG21
53 SEG19
52 SEG20
54 SEG18
55 SEG17
56 SEG16
57 SEG15
58 SEG14
59 SEG13
60 SEG12
61 SEG11
62 SEG10
63 SEG9
64 SEG8
65 SEG7
66 SEG6
68 SEG4
67 SEG5
70 SEG2
69 SEG3
72 SEG0
71 SEG1
73 C/D
74 OSC1(CS)
75 OSC2(CL)
76 E/RD
77 R/W(WR)
78 VSS
The SBN1661G_M18 , SBN1661G_M02 pad placement
79 DB0
3.3
DB1 80
50 SEG22
DB2 81
DB3 82
49 SEG23
DB4 83
DB5 84
47 SEG25
48 SEG24
46 SEG26
Y
DB6 85
DB7 86
45 SEG27
44 SEG28
VDD 87
43 SEG29
RESET/IF 88
FR 89
42 SEG30
V5 90
40 SEG32
41 SEG31
V3 91
39 SEG33
X
(0,0)
V2 92
M/S 93
38 SEG34
37 SEG35
chip size : 4162 μm x 3000 μm.
V4 94
36 SEG36
Pad size: 90 μm x 90 μm.
V1 95
35 SEG37
COM0 96
COM1 97
COM2 98
COM3 99
34 SEG38
33 SEG39
32 SEG40
chip ID
31 SEG41
SEG42 30
SEG43 29
SEG44 28
SEG45 27
SEG46 26
SEG47 25
SEG48 24
SEG49 23
SEG50 22
SEG51 21
SEG52 20
SEG53 19
SEG54 18
SEG55 17
SEG56 16
SEG57 15
SEG58 14
SEG59 13
9
COM13
SEG60 12
8
COM12
COM15 11
7
COM11
COM14 10
6
4
COM8
COM9
3
COM7
COM10
2
COM6
5
1
COM5
COM4 100
Note:
(1) The SBN1661G_M18 and the SBN1661G_M02 have the
same pad placement.
(2) The chip ID of the SBN1661G_M18 is AT18001-01.
(3) The chip ID of the SBN1661G_M02 is AT18001-02.
(4) The die origin is at the center of the chip.
(5) For chip_on_board_bonding, chip carrier should be
connected to VDD or left open. Chip carrier is the metal
pad to which the die is attached.
2007 Jul 05
Fig.4 The SBN1661G_M18, SBN1661G_M02 pad placement
8 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
51 SEG21
53 SEG19
52 SEG20
54 SEG18
55 SEG17
56 SEG16
57 SEG15
58 SEG14
59 SEG13
60 SEG12
61 SEG11
62 SEG10
63 SEG9
64 SEG8
65 SEG7
66 SEG6
68 SEG4
67 SEG5
70 SEG2
69 SEG3
72 SEG0
71 SEG1
73 C/D
74 CS
75 CL
76 E/RD
77 R/W(WR)
78 VSS
The SBN0080G_S18 , SBN0080G_S02 pad placement
79 DB0
3.4
DB1
80
50 SEG22
DB2
49 SEG23
DB3
81
82
DB4
83
47 SEG25
DB5
46 SEG26
DB6
84
85
DB7
86
VDD
87
43 SEG29
RESET/IF
88
42 SEG30
FR
89
41 SEG31
V5
90
91
V3
45 SEG27
Y
44 SEG28
40 SEG32
(0,0)
X
39 SEG33
chip size : 4162 μm x 3000 μm.
SEG79
92
93
SEG78
94
36 SEG36
SEG77
95
96
35 SEG37
33 SEG39
SEG74
97
98
SEG73
99
SEG72
100
34 SEG38
32 SEG40
chip ID
SEG42 30
SEG43 29
SEG44 28
SEG45 27
SEG46 26
SEG47 25
SEG48 24
SEG49 23
SEG50 22
SEG51 21
SEG52 20
SEG53 19
SEG54 18
SEG63
SEG55 17
9
SEG64
SEG56 16
8
SEG57 15
7
SEG65
SEG58 14
6
SEG66
SEG59 13
5
SEG67
SEG60 12
4
SEG68
SEG61 11
3
SEG69
SEG62 10
2
31 SEG41
1
SEG75
SEG70
SEG76
38 SEG34
37 SEG35
Pad size: 90 μm x 90 μm.
SEG71
V2
48 SEG24
Note:
(1) The SBN0080G_S18 and the SBN0080G_S02 have
the same pad placement.
(2) The chip ID of the SBN0080G_S18 is AT18001-03
(3) The chip ID of the SBN0080G_S02 is AT18001-04.
(4) The die origin is at the center of the chip.
(5) For chip_on_board_bonding, chip carrier should be
connected to VDD or left open. Chip carrier is the
metal pad to which the die is attached.
2007 Jul 05
Fig.5 The SBN0080G_S18, SBN0080G_S02 pad placement
9 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
3.5
The SBN1661G_M18, SBN1661G_M02 pad coordinates
Table 3
The SBN1661G_M18, SBN1661G_M02 pad coordinates (unit: μm)
PAD
NO.
PAD
NAME
X
Y
PAD
NO.
PAD
NAME
X
Y
PAD PAD
NO. NAME
X
Y
1
COM5
-1824
-1430
35
SEG37
2011
-732
69
SEG3
-498
1430
2
COM6
-1694
-1430
36
SEG36
2011
-597
70
SEG2
-628
1430
3
COM7
-1569
-1430
37
SEG35
2011
-462
71
SEG1
-758
1430
4
COM8
-1444
-1430
38
SEG34
2011
-327
72
SEG0
-888
1430
5
COM9
-1319
-1430
39
SEG33
2011
-192
73
C/D
-1062
1430
6
COM10
-1186
-1430
40
SEG32
2011
-57
74
OSC1
-1194
1430
7
COM11
-1053
-1430
41
SEG31
2011
78
75
OSC2
-1326
1430
8
COM12
-920
-1430
42
SEG30
2011
213
76
E/RD
-1458
1430
9
COM13
-787
-1430
43
SEG29
2011
348
77
R/W(WR)
-1590
1430
10
COM14
-654
-1430
44
SEG28
2011
483
78
VSS
-1722
1430
11
COM15
-521
-1430
45
SEG27
2011
618
79
DB0
-1854
1430
12
SEG60
-388
-1430
46
SEG26
2011
753
80
DB1
-2011
1358
13
SEG59
-255
-1430
47
SEG25
2011
883
81
DB2
-2011
1176
14
SEG58
-122
-1430
48
SEG24
2011
1013
82
DB3
-2011
1044
15
SEG57
11
-1430
49
SEG23
2011
1143
83
DB4
-2011
909
16
SEG56
144
-1430
50
SEG22
2011
1273
84
DB5
-2011
771
17
SEG55
277
-1430
51
SEG21
1842
1430
85
DB6
-2011
635
18
SEG54
410
-1430
52
SEG20
1712
1430
86
DB7
-2011
497
19
SEG53
543
-1430
53
SEG19
1582
1430
87
VDD
-2011
358
20
SEG52
676
-1430
54
SEG18
1452
1430
88
RESET/IF -2011
212
21
SEG51
809
-1430
55
SEG17
1322
1430
89
FR
-2011
81
22
SEG50
942
-1430
56
SEG16
1192
1430
90
V5
-2011
-50
23
SEG49
1075
-1430
57
SEG15
1062
1430
91
V3
-2011
-180
24
SEG48
1208
-1430
58
SEG14
932
1430
92
V2
-2011
-326
25
SEG47
1341
-1430
59
SEG13
802
1430
93
M/S
-2011
-456
26
SEG46
1474
-1430
60
SEG12
672
1430
94
V4
-2011
-586
27
SEG45
1607
-1430
61
SEG11
542
1430
95
V1
-2011
-716
28
SEG44
1740
-1430
62
SEG10
412
1430
96
COM0
-2011
-846
29
SEG43
1873
-1430
63
SEG9
282
1430
97
COM1
-2011
-976
30
SEG42
2006
-1430
64
SEG8
152
1430
98
COM2
-2011
-1106
31
SEG41
2011
-1272
65
SEG7
22
1430
99
COM3
-2011
-1236
32
SEG40
2011
-1137
66
SEG6
-108
1430
100
COM4
-2011
-1388
33
SEG39
2011
-1002
67
SEG5
-238
1430
34
SEG38
2011
-867
68
SEG4
-368
1430
2007 Jul 05
10 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
3.6
The SBN0080G_S18, SBN0080G_S02 pad coordinates
Table 4
The SBN0080G_S18, SBN0080G_S02 pad coordinates ( unit: μm )
Pad
No.
Pad
Name
X
Y
Pad
No.
Pad
Name
X
Y
Pad
No.
Pad Name X
Y
1
SEG71
-1824
-1430
35
SEG37
2011
-732
69
SEG3
-498
1430
2
SEG70
-1694
-1430
36
SEG36
2011
-597
70
SEG2
-628
1430
3
SEG69
-1569
-1430
37
SEG35
2011
-462
71
SEG1
-758
1430
4
SEG68
-1444
-1430
38
SEG34
2011
-327
72
SEG0
-888
1430
5
SEG67
-1319
-1430
39
SEG33
2011
-192
73
C/D
-1062
1430
6
SEG66
-1186
-1430
40
SEG32
2011
-57
74
CS
-1194
1430
7
SEG65
-1053
-1430
41
SEG31
2011
78
75
CL
-1326
1430
8
SEG64
-920
-1430
42
SEG30
2011
213
76
E/RD
-1458
1430
9
SEG63
-787
-1430
43
SEG29
2011
348
77
R/W(WR)
-1590
1430
10
SEG62
-654
-1430
44
SEG28
2011
483
78
VSS
-1722
1430
11
SEG61
-521
-1430
45
SEG27
2011
618
79
DB0
-1854
1430
12
SEG60
-388
-1430
46
SEG26
2011
753
80
DB1
-2011
1358
13
SEG59
-255
-1430
47
SEG25
2011
883
81
DB2
-2011
1176
14
SEG58
-122
-1430
48
SEG24
2011
1013
82
DB3
-2011
1044
15
SEG57
11
-1430
49
SEG23
2011
1143
83
DB4
-2011
909
16
SEG56
144
-1430
50
SEG22
2011
1273
84
DB5
-2011
771
17
SEG55
277
-1430
51
SEG21
1842
1430
85
DB6
-2011
635
18
SEG54
410
-1430
52
SEG20
1712
1430
86
DB7
-2011
497
19
SEG53
543
-1430
53
SEG19
1582
1430
87
VDD
-2011
358
20
SEG52
676
-1430
54
SEG18
1452
1430
88
RESET/IF
-2011
212
21
SEG51
809
-1430
55
SEG17
1322
1430
89
FR
-2011
81
22
SEG50
942
-1430
56
SEG16
1192
1430
90
V5
-2011
-50
23
SEG49
1075
-1430
57
SEG15
1062
1430
91
V3
-2011
-180
24
SEG48
1208
-1430
58
SEG14
932
1430
92
V2
-2011
-326
25
SEG47
1341
-1430
59
SEG13
802
1430
93
SEG79
-2011
-456
26
SEG46
1474
-1430
60
SEG12
672
1430
94
SEG78
-2011
-586
27
SEG45
1607
-1430
61
SEG11
542
1430
95
SEG77
-2011
-716
28
SEG44
1740
-1430
62
SEG10
412
1430
96
SEG76
-2011
-846
29
SEG43
1873
-1430
63
SEG9
282
1430
97
SEG75
-2011
-976
30
SEG42
2006
-1430
64
SEG8
152
1430
98
SEG74
-2011
-1106
31
SEG41
2011
-1272
65
SEG7
22
1430
99
SEG73
-2011
-1236
32
SEG40
2011
-1137
66
SEG6
-108
1430
100
SEG72
-2011
-1388
33
SEG39
2011
-1002
67
SEG5
-238
1430
34
SEG38
2011
-867
68
SEG4
-368
1430
2007 Jul 05
11 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
3.7
Pin(pad) signal difference among the four members of the SBN1661G_X
All four members of the SBN1661G_X series have the same pad sequence and placement. However, some pins(pads)
have different signals for different types. A comparison is given in Table 5.
Table 5
Comparison of pin(pad) signals
Type
Pin(pad)
1~11
Pin(pad)
74
Pin(pad)
75
Pin(pad)
93
Pin(pad)
94
Pin(pad)
95
Pin(pad)
96~100
SBN1661G_M18
COM5~15
OSC1
OSC2
M/S
V4
V1
COM0~4
SBN1661G_M02
COM5~15
CS
CL
M/S
V4
V1
COM0~4
SEG71~61
CS
CL
SEG79
SEG78
SEG77
SEG76~72
SBN0080G_S18
SBN0080G_S02
3.8
Pin (pad) states after hardware RESET
Table 6
Pin(pad) states after RESET
SBN1661G_M18, SBN1661G_M02
SBN0080G_S18, SBN0080G_S02
signal
states after RESET
signal
states after RESET
DB0~DB7
tri-state
DB0~DB7
tri-state
COM0~COM15
VDD
SEG0~SEG79
VDD
SEG0~SEG61
VDD
FR(SBN1661G_M18)
tri-state
OSC2 (SBN1661G_M18)
tri-state
2007 Jul 05
12 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
3.9
The SBN1661G_M18 and the SBN1661G_M02 signal description
Table 7 Pin (pad) signal description
To avoid a latch-up effect at power-on: VSS − 0.5 V < voltage at any pin at any time < VDD + 0.5 V .
Pin
number
SYMBOL
I/O
DESCRIPTION
COMMON driver outputs.
The output voltage level of COMMON outputs are decided by the combination of
the alternating frame signal (FR) and the internal COMMON COUNTER, which
generates raster-scanning COMMON signals. Depending on the value of the frame
signal and the COMMON counter output, a single voltage level is selected from
VDD, V1, V4, or V5 for COMMON driver , as shown in Fig. 6.
1~11,
96~100
COM5~15,
COM0~4
Output
FR
Common
Counter
output
COMMON
output
0
0
1
0
1
0
1
0
1
0
1
0
1
V4
V5
V1
VDD
V4
V5
V1
VDD
Fig.6 COMMON driver output voltage level
SEGNENT driver outputs.
The output voltage level of SEGMENT outputs are decided by the combination of
the alternating frame signal (FR) and display data. Depending on the value of the
frame signal and the display data, a sinlge voltage level is selected from VDD, V2,
V3, or V5 for SEGMENT driver, as shown in Fig. 7.
12~72
SEG60~0
Output
0
1
FR
0
Display
Data bit
0
1
0
1
0
1
0
1
V3
VDD
V2
V5
V3
VDD
V2
V5
SEG output
0
1
Fig.7 SEGMENT driver output voltage level
Selection of command or data.
73
C/D
Input
When C/D=0, the data on the 8-bit data bus (DB0~DB7) are either COMMAMD,
data to be written to an internal register, or data read from the internal Status
Register.
When C/D=1, the data on the 8-bit data bus (DB0~DB7) are related to the Display
Data Memory. They are the data to be written to or read from the Display Data
Memory.
2007 Jul 05
13 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
Pin
number
SYMBOL
OSC1
I/O
Input
74
DESCRIPTION
For the SBN1661G_M18, pin 74 is the OSC1 pin of the on-chip RC oscillator. It is
the input pin to the oscillator. An external resistor should be connected across the
OSC1 and the OSC2.
For the SBN1661G_M02, pin 74 is the CS pin. Usually, a signal decoded from the
host microcontroller address lines or a port line (C51) is connected to this pin.
CS
OSC2
Output
For the SBN1661G_M18, pin 75 is the OSC2 pin. It is the output pin of the on-chip
RC oscillator.
CL
Input
For the SBN1661G_M02, pin 75 is the CL pin. Clock from master or an external
clock source should be added to this pin.
75
Enable signal (E) for the 68-type microcontroller, or READ (RD) signal for the
80-type microcontroller.
76
E/(RD)
Input
If a 68-type microcotroller is selected as the host microcontroller, this pin should be
connected to the ENABLE output of the microcontroller. A HIGH level on this pin
indicates that the microcontroller intends to select the SBN1661G_X series.
If a 80-type microcontroller is selected as the host microcontroller, this pin should
be connected to the RD output of the microcontroller. A LOW level on this pin
indicates that the microcontroller intends to read from the SBN1661G_X series..
Read/Write (R/W) signal for the 68-type microcontroller, or WRITE(WR) signal for
the 80-type microcontroller.
77
R/W(WR)
Input
If a 68-type microcotroller is selected as the host microcontroller, this pin should be
connected to the R/W output of the microcontroller. A HIGH level on this pin
indicates that the microcontroller intends to read from the SBN1661G_X series. A
LOW level on this pin indicates that the microcontroller intends to write to the
SBN1661G_X series.
If a 80-type microcontroller is selected as the host microcontroller, this pin should
be connected to the WR output of the microcontroller. A LOW level on this pin
indicates that the microcontroller intends to write to the SBN1661G_X series.
78
VSS
Ground pin.
Bi-direction, tri-state 8-bit parallel data bus for interface with a host microcontroller.
79~86
DB0~DB7
I/O
87
VDD
Input
This data bus is for data transfer between the host microcontroller and the
SBN1661G_X.
Power supply for logic part of the chip.
2007 Jul 05
The VDD should be in the range from 2.7 volts to 5.5 volts.
14 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
Pin
number
SYMBOL
I/O
DESCRIPTION
Hardware RESET and interface type selection.
This pin is a dual function pin. It can be used to reset the SBN1661G_X and select
the type of interface timing.
The hardware RESET is edge-sensitive. It is not level-sensitive. That is, either a
falling edge or a rising edge on this pin can reset the chip. The voltage level after
the reset pulse selects the type of interface timing. If the voltage level after the reset
pulse stays at HIGH, interface timing for the 68-type microcontroller is selected. If
the voltage level after the reset pulse stays at LOW, then interface timing for the
80-type microcontroller is selected.
Therefore, a positive RESET pulse selects the 80-type microcontroller for interface
and a negative RESET pulse selects the 68-type microcontroller for interface.
88
RESET/IF
Input
The following diagram illustrates the reset pulse and the selected type of
microcontroller.
Interface timing for the 80-type microcontroller is selected.
Positive RESET pulse
Interface timing for the 68-type microcontroller is selected.
Negative RESET pulse
Fig.8 RESET pulse interface timing selection
Frame output or input.
89
FR
90, 91,
92, 94,
95
V5, V3, V2,
V4, V1
I/O
The frame signal is the AC siganl for generating alternating bias voltage of reverse
polarities for LCD cell. When the chip is used as Master in a Master-Slave
connection, this pin is an output pin and sends frame signal to the slave. When the
chip is used as Slave, this pin is an input pin and accepts frame signal from the
master.
External LCD Bias voltage.
Input
The condition VDD≥V1≥V2≥V3≥V4≥V5 must always be met. In addition,
VLCD (V5-VDD) should not exceed -13 volts.
Selection for Master or Slave in a master-slave conneciton.
When this pin is connected to VDD (hardwired-connection), the chip is used as
Master. When this pin is connected to VSS, the chip is used as Slave.
93
M/S
Input
M/S
FR
COM0-COM15 output
OSC1
OSC2
VDD
Output
COM0-COM15
Input
Output
VSS
Input
COM31-COM16
NC
Input
* The common scanning order for the slave driver is reverse to that for master.
2007 Jul 05
15 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
4
A SBN1661G_X-BASED DISPLAY SYSTEM
A SBN1661G_X-based display system is shown in Fig. 9.
The SBN1661G_X , on the one side, interfaces with a host microcontroller via address bus , data bus, and control bus.
The address bus from the microcontroller needs to be further decoded to generate Chip Select signal. The host
microcontroller can perform READ/WRITE operation to the on-chip Display Data Memory, can send commands to the
SBN1661G_X, and can program the internal registers to congifure the SBN1661G_X. How data is to be displayed on the
LCD panel is completely controlled by the host microcontroller.
On the other side, the SBN1661G_X provides 15 COMMON drivers and 61 SEGMENT drivers to drive the LCD panel.
To expand the COMMON number and SEGMENT number, both the SBN1661G_M18 and SBN1661G_M02 can be used
either as a master or as a slave in a master-slave connection. The synchronization between the master and the slave is
via the FR (frame) signal and the CL (clock) signal supplied from the master to the slave.
If only segment number needs to be expanded, then the SBN0080G_S18 or the SBN0080G_S02 can be used as slave.
Address bus
Decoder
SBN1661G_X
COM0
(master)
COM15
Data bus
Host
microcontroller Control bus
Display Data
Memory
68-series
80-seris
Registers
SEG1
SEG61
C51-series
LCD Panel
SBN1661G_X
COM0
(slave)
COM15
Display Data
Memory
Registers
RESET
SEG1
SEG61
LCD Bias Power
Supply
Fig.9 A SBN1661G_X series-based display system
2007 Jul 05
16 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
5
INTERFACE WITH A HOST MICROCONTROLLER
5.1
Selection of interface type by use of the RESET/IF pin(pad)
The SBN1661G_X series can accept two types of interface timing for two types of microconftroller: the 68-type
micrcontrollers and the 80-type microcontrollers. Selection of interface type is by use of the dual-function RESET/IF
pin(pad). If the voltage at the RESET/IF pin(pad) stays at HIGH after RESET pulse, then the 68-type interface timing is
selected. If the voltage at the RESET/IF pin(pad) stays at LOW after RESET pulse, then the 80-type interface timing is
selected.
The RESET of the SBN1661G_X is edge-sensitive, instead of level-sensitive. That is, a pulse on the RESET/IF input
triggers reset only on the rising edge and falling edge of the pulse. The voltage level after the RESET pulse is used to
select interface type.
5.2
Interface signal and operation
The interface signal between the host microcontroller and the SBN1661G_X are data bus and control bus. The data bus
is an 8-bit (DB0~DB7) bi-directional bus. The control bus is composed of the following siganls: C/D, E/(RD), and
R/W(WR).
By means of data bus and control bus, the host microcontroller can write data to the on-chip Display Data Memory, can
read data from the Display Data Memory, can program the internal registers, can send commands, and can read status
of the chip.
It is the host microcontroller’s responsibility to put proper data and timing on the data bus and control bus to ensure proper
communication.
Table 8 lists the setting for control bus and the types of interface operation.
Table 8
Interface signal and microcontroller operation
COMMAN
/DATA
68-type
interface
C/D
R/W
RD
WR
1
1
0
1
The host microcontroller reads data from the Display Data
Memory.
1
0
1
0
The host microcontroller writes data to the Display Data
Memory
0
1
0
1
The host microcontroller reads the Status Register.
0
0
1
0
The host microcontroller issues a command or writes data
to an internal register.
5.3
80-type interface
Operation
Interface Timing
Please refer to Fig. 22 and Fig. 24 for interface timing diagram and Table 42 , Table 43, Table 44, and Table 45 for AC
characteristics of interface timing.
5.4
Interface Circuit
Please refer to Fig. 24, Fig. 25, and Fig. 26 for interface circuit examples.
2007 Jul 05
17 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
6
DISPLAY DATA MEMORY AND LCD DISPLAY
The Display Data Memory is a static memory bit(cell) array of 32-row x 80-column. So, the total bit number of the Display
Data Memory is 32 x 80 = 2560 bits. Each bit of the memory is mapped to a single pixel (dot) on the LCD panel. A “1”
stored in the Display Data Memory bit corresponds to an ON pixel (black dot in normal display) of the LCD panel. A “0”
stored in the Display Data Memory bit corresponds to an OFF pixel (background dot in normal display) of the LCD panel.
Column outputs(Column 0~79) of the Display Data Memory is mapped to SEG 0~79 outputs of the SBN1661G_X. The
mapping can be normal mapping or inverse mapping. Normal mapping means that Column0 is mapped to SEG0,
Column1 to SEG1, Column2 to SEG2, and so on. Inverse mapping means that Column0 is mapped to SEG79, Column1
to SEG78, Column2 to SEG77, and so on. The mapping relation is decided by the Column/Segment Mapping Register.
Row 0
COM 0
Row 1
COM 1
Row 2
COM 2
Row 3
COM 3
Row 28
COM 15
SEG 79
SEG 78
SEG 77
SEG 2
SEG 1
SEG 0
Column 79
Column 78
Column 77
Column 2
Column 1
Column 0
Any row (80 bits) of the Display Data Memory can be selected as the first row (COM0) to be displayed on the LCD panel.
This is decided by the Display Start Line Register. The Display Start Line Register points at the first row of a block of the
Display Data Memory, which will be mapped to COM0 of the LCD display. The length of the block of the memory can be
32 rows or 16 rows, which is decided by the Duty Select Register.
Row 29
LCD panel pixel array
Row 30
Row 31
Display Data Memory Cell Array
Fig.10 Memory cell array and LCD pixel array
2007 Jul 05
18 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
7
DISPLAY CONTROL INSTRUCTIONS AND REGISTERS
7.1
Registers and their states after hardware RESET
The SBN1661G_X has a set of registers. To ensure proper operation of the devices, these registers must be
programmed with proper values after hardware reset.
The registers and their states after RESET is given in Table 9.
Table 9
Registers and their states after RESET
Register Name
States after
RESET
Display ON/OFF Register
The Display ON/OFF Register is a 1-bit register. After RESET,
0
its value is LOW and, therefore, the LCD display is turned OFF.
Display Start Line Register
The Display Start Line Register is a 6-bit register. After RESET,
its value is 0 0000 and Row0 of the Display Data Memory is
mapped to COM0.
00 0000
Page Addres Register
The Page Address Register is a 2-bit register. After RESET, its
value is 11 and, therefore, it points to Page 3 of the Display
Data Memory.
11
Column Address Register
The Column Address Register is a 7-bit register. After RESET,
its value is 000 0000 and, therefore, it points to column 0 of the
Display Data Memory.
000 0000
The Static Drive ON/OFF Register is a 1-bit register. After
RESET, its value is LOW and static display is turned OFF.
0
The Duty Select Register is a 1-bit register. After RESET, its
value is HIGH and 1/32 display duty is selected.
1
The Column/Segment Mapping Register is a 1-bit register.
After RESET, its value is LOW and normal mapping is selected.
0
The Status Register shows the current state of the
SBN1661G_X. It is a 4-bit register, with each bit showing the
status of a programmed function.
0000 0000
Static Drive ON/OFF Register
Duty Select Register
Column/Segment Mapping
Register
Status Register
7.2
Description
Display ON/OFF and the Display ON/OFF Register
The Display ON/OFF Register is a 1-bit Register. When this bit is progammed to HIGH, the display is turned ON.
When this bit is programmed to LOW, the display is turned OFF. When display is turned OFF, SEG0~SEG60 will stay at
either V2 or V3, and COM0~COM15 will stay at their previous value before the Display OFF command is issued.
To program this register, the setting of control bus is given in Table 10 and the setting of the data bus is given in Table 11.
Table 10 Setting of the control bus for programming the Display ON/OFF Register
C/D
E/(RD)
R/W(WR)
0
1
0
Table 11 Setting of the data bus for programming the Display ON/OFF Register
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
0
1
0
1
1
1
D0
When D0=1, the code is AF(Hex) and the display is turned ON. When D0=0, the code is AE(Hex) and the display is turned
OFF.
2007 Jul 05
19 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
7.3
Display Start Line and the Display Start Line Register
SEG 79
SEG 78
SEG 77
SEG 2
SEG 1
COM 0
Column 79
Column 78
Column 77
Column 2
Column 1
Column 0
SEG 0
The Display Start Line Register is a 5-bit Register. It points at the first row of a block of the Display Data Memory, which
will be mapped to COM0. The length of the block of the memory can be 32 rows or 16 rows, which is decided by the Duty
Select Register. For example, if the Display Start Line Register is programmed with 00010 ( decimal 2) and display duty
is 1/32, then Row2 of the Display Data Memory will be mapped to COM0 of LCD panel, Row3 to COM1, Row4 to COM2,
Row30 to COM28, Row31 to COM29, Row0 to COM30, and finally Row1 to COM31, as illustrated in Fig. 11. However,
in this case, only Row2~Row17 can be displayed on COM0~COM15, as COM16~COM31 are not availabe from the chip.
COM 1
COM 2
COM 3
Row 0
Row 1
Row 2
Row 3
COM 28
0
0
0
1
COM 29
0
A4 A3 A2 A1 A0
COM 30
Display Start Line Register
COM 31
Row 28
Row 29
LCD panel
Row 30
Row 31
Display Data Memory
Fig.11 Display Start Line Register
To program this register, the setting of the control bus is given in Table 12 and the setting of the data bus is given in
Table 13.
Table 12 The setting of the control bus for programming the Display Start Line Register
C/D
E/(RD)
R/W(WR)
0
1
0
Table 13 The setting of the data bus for programming the Display Start Line Register
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
1
0
A4
A3
A2
A1
A0
A4, A3, A2, A1, and A0 are Start Line address bits and they can be programmed with a value in the range from 0 to 31.
Therefore, the code can be from 1100 0000 (C0 Hex) to 1101 1111 (DF Hex).
2007 Jul 05
20 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
7.4
Display Data Memory Page and the Page Address Register
Page 1
Page 2
Page 3
Bit7
Bit0
Bit1
Bit2
Bit3
Bit4
Bit5
Bit6
Bit7
Bit0
Bit1
Bit2
Bit3
Bit4
Bit5
Bit6
Bit7
Bit0
Bit1
Bit2
Bit3
Bit4
Bit5
Bit6
Bit7
Column 79(Byte79)
Column 78(Byte78)
Column 77(Byte77)
Row0
Row1
Row2
Row3
Row4
Row5
Row6
Row7
Row8
Row9
Row10
Row11
Row12
Row13
Row14
Row15
Row16
Row17
Row18
Row19
Row20
Row21
Row22
Row23
Row24
Row25
Row26
Row27
Row28
Row29
Row30
Row31
Column 3(Byte3)
Column 2(Byte2)
Column 1(Byte1)
Page 0
Bit0
Bit1
Bit2
Bit3
Bit4
Bit5
Bit6
Column 0(Byte0)
The on-chip Display Data Memory is divided into 4 pages: Page 0, Page 1, Page 2, and Page 3, with each page having
80 bytes in horizontal direction. Page 0 is from Row 0 to Row 7, Page 1 from Row 8 to Row 15, Page 2 from Row 16 to
Row 23, and Page 3 from Row 24 to Row 31, as shown in Fig 12. When the host microtroller intends to perform a
READ/WRITE operation to the Display Data Memory, it has to program the Page Adrress Register to indicate which page
it intends to access.
Fig.12 Page/Column allocation of the Display Data Memory
To program this register, the setting of the control bus is given in Table 14 and the setting of the data bus is given in Table
15.
Table 14 The setting of the control bus for programming the Page Address Register
C/D
E/(RD)
R/W(WR)
0
1
0
Table 15 The setting of the data bus for programming the Page Address Register
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
0
1
1
1
0
A1
A0
A1and A0 are page address bits and can be programmed with a value in the range from 0 to 3. A1A0=00 selects Page 0,
A1A0=01 selects Page 1, A1A0=10 selects Page 2, and A1A0=11 selects Page 3. Therefore, the code can be from 1011
1000 (B8 Hex) to 1011 1011 (BB Hex).
2007 Jul 05
21 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
7.5
Column address and the Column Address Register
The Column Address Register points at a column of the Display Data Memory which the host microcontroller intends to
perform a READ/WRITE operation. The Column Address Register automatically increments by 1 after a READ or WRITE
operation is finished. When the Column Address Register reaches 79, it overflows to 0. Please refer to Fig.12 for the
column sequence in a page of the Display Data Memory.
To program this register, the setting of the control bus is given in Table 16 and the setting of the data bus is given in Table
17.
Table 16 The setting of the control bus for programming the Column Address Register
C/D
E/(RD)
R/W(WR)
0
1
0
Table 17 The setting of the data bus for programming the Column Address Register
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
0
A6
A5
A4
A3
A2
A1
A0
A6~A0 are column address bits and can be programmed with a value in the range from 0 to 79. Therefore, the code can
be from 0000 0000 (00 Hex) to 0100 1111 (4F Hex).
2007 Jul 05
22 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
7.6
Mapping between Memory Cloumns and Segments and the Column/Segment Mapping Register
The Column/Segment Mapping Register is a 1-bit register and selects the mapping relation between the column outputs
of the Display Data Memory and the Segment outputs SEG0~SEG79.
If this register is programmed with HIGH, then the data from column 79 of the Display Data Memory will be output from
SEG0. This type of mapping is called inverted mapping.
If this register is programmed with LOW, then data from column 0 of the Display Data Memory will be output from SEG0.
This type of mapping is called normal mapping.
By use of this register, the flexibility of component placement and routing on a PCB can be increased.
SEG 77
SEG 78
SEG 79
Column 78
Column 79
SEG 2
Column 77
Row 1
Row 2
Row 3
Row 3
Row 28
Row 28
Row 29
Row 29
Row 30
Row 30
Row 31
Row 31
Display Data Memory
Column 2
Row 0
Column 1
Column 79
Column 78
Column 77
Column 2
Column 1
Row 2
Column 0
Row 1
Column 0
Inverted mapping
(D=1)
Normal Mapping
(D=0)
Row 0
SEG 1
SEG 0
SEG 79
SEG 78
SEG 77
Segment Driver
SEG 2
SEG 1
SEG 0
Segment Driver
Display Data Memory
Fig.13 Column/Segment Mapping Register.
To program this register, the setting of the control bus is given in Table 18 and the setting of the data bus is given in
Table 19.
Table 18 The setting of the control bus for programming the Column/Segment Mapping Register
C/D
E/(RD)
R/W(WR)
0
1
0
Table 19 The setting of the data bus for programming the Memory/Segment Mapping Register
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
0
1
0
0
0
0
D
The least significant bit D can be programmed with either 0 or 1. Therefore, the codes are A0 Hex or A1 Hex.
2007 Jul 05
23 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
7.7
Static Drive ON/OFF and the Static Drive ON/OFF register
The Static Drive ON/OFF Register is a 1-bit register. It is used to turn ON or OFF the Static Drive Mode of the
SBN1661G_X.
When this register is programmed with HIGH, Static Drive Mode is turned ON and the device enters into Static Drive
Mode, in which the internal clock circuitry is disabled and the switching of the internal logic is suspended. When this
register is programmed with LOW, Static Drive Mode is turned OFF and the chip returns to normal operation.
This register is used in combination with the Display ON/OFF register to make the current consumption of the LCD
module reduced to almost static level. By turning OFF the display and turning ON the static drive mode,the chip is
configured into the following state:
• all COMMON and SEGMENT outputs are set to VDD,
• on-chip oscillator or external clock is inhibited and internal logic circuit stays idle,
• OSC2 is in floating state (please refer to Section 11 , On-chip RC Oscillator), and
• the state of registers and the data of the Display Data Memory are kept unchanged.
In addition to turning ON the static drive mode and turning OFF the display, to really reduce the power consumption of
the LCD module, the host microcontroller should also send out a power-save signal to turn off the PNP transistor in the
bias circuit, such that the current flow from VDD to VEE can be cut off, as shown in Fig. 14.
VDD
VDD
V0
Microcontroller
C
V1
C
V2
C
V3
C
V4
C
V5
V0
VDD
V1
SEG0~SEG60
V2
V3
COM0~COM15
V4
V5
VSS
Power Save Signal
VEE
Fig.14 Power Save Mode
To program this register, the setting of the control bus is given in Table 20 and the setting of the data bus is given in
Table 21.
Table 20 The setting of the control bus for programming the Static Drive ON/OFF Register
C/D
E/(RD)
R/W(WR)
0
1
0
Table 21 The setting of the data bus for programming the Static Drive ON/OFF Register
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
0
1
0
0
1
0
D
The least significant bit D0 can be programmed with either 0 or 1. Therefore, the code is A4 Hex or A5 Hex.
2007 Jul 05
24 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
7.8
Select Duty and the Select Duty Register
The Select Duty Register is a 1-bit register. If it is programmed with HIGH, 1/32 display duty is selected. If it is
programmed with LOW, 1/16 display duty is selected.
To program this register, the setting of the control bus is given in Table 22 and the setting of the data bus is given in
Table 23.
Table 22 The setting of the control bus for programming the Select Duty Register
C/D
E/(RD)
R/W(WR)
0
1
0
Table 23 The setting of the data bus for programming the Select Duty Register
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
0
1
0
1
0
0
D
The least significant bit D can be programmed with either 0 or 1. Therefore, the code is A8 Hex or A9 Hex.
In a Master-Slave connection using the SBN1661G_M18 or the SBN1661G_M02 as the master, COM0~COM15 will be
from the master and COM16~COM31 will be from the slave. The Select Duty Register of both the Master and the Slave
should be programmed with HIGH to select 1/32 duty. Fig.15 shows the COMMON sequence of this connection.
Frame Signal
(From Master)
COM0~COM15
(From Master)
COM16~COM31
(From Slave)
0
1
2
13 14 15
0
16 17 18
29 30 31
1
2
13 14 15
16 17 18
29 30 31
Fig.15 COMMON sequence of Master-Slave connection
This register is not available in the SBN0080G_S18 and the SBN0080G_S02, because both the devices are purely
Segment Drivers and their duty cycle is decided by the FR and the CL from the master.
2007 Jul 05
25 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
7.9
Status Read and Status Register
The Status Register shows the current state of the SBN1661G_X. It can be read by the host microcontroller. Bit 7~4
shows the status and Bit 3~0 are always fixed at 0.
To read the Status Register, the setting of the control bus is given in Table 24, the bit allocation is given in Table 25 and
the description for each bit is given in Table 26.
Table 24 The setting of the control bus for reading the Status Register
C/D
E/(RD)
R/W(WR)
0
0
1
Table 25 The Status Register bit allocation
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
BUSY
MAPPING
ON/OFF
RESET
0
0
0
0
Table 26 The Status Register bit description
Bit
Description
BUSY
BUSY=1 indicates that the SBN1661G_X is currently busy and can not accept new command or data.
The SBN1661G_X is executing a command or is in the process of reset.
BUSY=0 indicates that the SBN1661G_X is not busy and is ready to accept new command or data.
MAPPING
MAPPING=1 indicates that the Column/Segment Mapping Register has been programmed with a
value of “1” and the SEG0 is mapped to Column 79 of the Display Data Memory (inverted mapping).
MAPPING=0 indicates that the Column/Segment Mapping Register has been programmed with a
value of “0” and the SEG0 is mapped to Column 0 of the Display Data Memory (normal mapping).
ON/OFF
The ON/OFF bit indicates the current of status of display.
If ON/OFF=0, then the display has been turned ON.
If ON/OFF=1, then the display has been turned OFF.
Note that the polarity of this bit is inverse to that of the Display ON/OFF Register.
RESET
RESET=1 indicates that the SBN1661G_X is currently in the process of being reset.
RESET=0 indicates that the SBN1661G_X is currently in normal operation.
2007 Jul 05
26 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
8
COMMANDS
The host microcontroller can issue commands to the SBN1661G_X. Table 27 lists all the commands. When issuing a
command, the host microcontroller should put the command code on the data bus. The host microcontroller should also
give the control bus C/D, E(RD), and R/W(WR) proper value and timing.
Table 27 Commands
COMMAND CODE
COMMAND
FUNCTION
D7
D6
D5
D4
D3
D2
D1
D0
Write Display Data
Data to be written into the Display Data
Memory.
Write a byte of data to the Display Data Memory.
Read Display Data
Data read from the Display Data
Memory.
Read a byte of data from the Display Data Memory.
Read-Modify-Write
1
1
1
0
0
0
0
0
Start Read-Modify-Write operation.
END
1
1
1
0
1
1
1
0
Stop Read-Modify-Write operation.
Software Reset
1
1
1
0
0
0
1
0
Software Reset.
8.1
Write Display Data
The Write Display Data command writes a byte (8 bits) of data to the Display Data Memory. Data is put on the data bus
by the host microcontroller. The location which accepts this byte of data is pointed to by the Page Address Register and
the Column Address Register. At the end of the command operation, the content of the Column Address Register is
automatically incremented by 1.
For page address and column address of the Display Data Memory, please refer to Fig. 12.
Table 28 gives the control bus setting for this command.
Table 28 The setting of the control bus for issuing Write Display Data command
C/D
E/(RD)
R/W(WR)
1
1
0
2007 Jul 05
27 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
8.2
Read Display Data
The Read Display Data command starts a 3-step operation.
1. First, the current data of the internal 8-bit output latch of the Display Data Memory is read by the microcontroller, via
the 8-bit data bus DB0~DB7.
2. Then, a byte of data of the Display Data Memory is transferred to the 8-bit output latch from a location specified by
the Page Address Register and the Column Address Register,
3. Finally, the content of the Column Address Register is automatically incremented by one.
Fig. 16 shows the internal 8-bit ouptut latch located between the 8-bit I/O data bus and the Display Data Memory cell
array. Because of this internal 8-bit output latch, a dummy read is needed to obtain correct data from the Display Data
Memory.
For Display Data Write operation, a dummy write is not needed, because data can be directly written from the data bus
to internal memory cells.
DB7
DB6
DB4
DB5
DB2
DB3
DB1
DB0
(8-bit bi-directional data bus)
Write Display Data
Row Address
Decoder
Read Display Data
8-bit output latch
Display Data Memory cell array
( 32 row x 80 column )
Column Address Decoder
Fig.16 Read Display Data Memory
Table 29 gives the control bus setting for this command.
Table 29 The setting of the control bus for issuing Read Display Data command
C/D
E/(RD)
R/W(WR)
1
0
1
2007 Jul 05
28 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
8.3
Read-Modify-Write
When the Read-Modify-Write command is issued, the SBN1661G_X enters into Read-Modify-Write mode.
In normal operation, when a Read Display Data command or a Write Display Data command is issued, the content of the
Column Address Register is automatically incremented by one after the command operation is finished. However, during
Read-Modify-Write mode, the content of the Column Address Register is not incremented by one after a Read Display
Data command is finished; only the Write Display Data command can make the content of the Column Address Register
automatically incremented by one after the command operation is finished.
During Read-Modify-Write mode, any other registers, except the Column Address Register, can be modified. This
command is useful when a block of the Display Data Memory needs to be repeatedly read and updated.
Fig. 17 gives the change sequence of the Column Address Register during Read-Modify-Write mode. Figure 18 gives
the flow chart for Read-Modify-Write command.
END command issued.
Read-Modify-Write command issued.
Read-Modify-Write duration
Column Address
N
N+1
N+2
Internal Buffer Register
N+3
N+m
N
Re-load column address by issuing the END command
Fig.17 Column address change during Read-Modify-Write
2007 Jul 05
29 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
Set Page Address Register
Set Column Address Register
Read-Modify-Write command
Dummy Read
Read Display Data Memory
Write Display Data Memory
No
Finish Modifying ?
Yes
END
Fig.18 The flowchart for Read-Modify-Write
Table 30 gives the setting for the control bus and the setting of the data bus is given in Table 31.
Table 30 The setting of the control bus for the Read-Modify-Write command
C/D
E/(RD)
R/W(WR)
0
1
0
Table 31 The setting of the data bus for the Read-Modify-Write command
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
1
1
0
0
0
0
0
The command code is E0 Hex.
8.4
The END command
The END command releases the Read-Modify-Write mode and re-loads the Column Address Register with the value
previously stored in the internal buffer (refer to Fig. 17) when the Read-Modify-Write command was issued.
Table 32 gives the setting for the control bus and the setting of the data bus is given in Table 33.
2007 Jul 05
30 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
Table 32 The setting of the control bus for the END command
C/D
E/(RD)
R/W(WR)
0
1
0
Table 33 The setting of the data bus for the END command
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
1
1
0
1
1
1
0
The command code is EE Hex.
8.5
Software RESET command
The Software Reset command is different from the hardware reset and can not be used to replace hardware reset.
When Software Reset is issued by the host microcontroller,
• the content of the Display Start Line Register is cleared to zero(A4~A0=00000),
• the Page Address Register is set to 3 (A1 A0 = 11),
• the content of the Display Data Memory remains unchanged, and
• the content of all other registers remains unchanged.
Table 34 gives the setting for the control bus and the setting of the data bus is given in Table 35.
Table 34 The setting of the control bus for Software RESET
C/D
E/(RD)
R/W(WR)
0
1
0
Table 35 The setting of the data bus for Software RESET
D7(MSB)
D6
D5
D4
D3
D2
D1
D0(LSB)
1
1
1
0
0
0
1
0
The command code is E2 Hex.
2007 Jul 05
31 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
9
LCD BIAS CIRCUIT
A typical LCD bias circuit is shownin Fig. 19. The condition VDD≥ V1 ≥ V2 ≥ V3 ≥ V4 ≥ V5 must always be met. The
maximum allowed voltage for LCD bias (VLCD=VDD-V5) should not exceed 13 volts.
COMPONENT
RECOMMENDED
VALUE
C
0.1 μF,
electrolytic
R1
2.2K
R2
7.5K
R3
10K
TR1
PNP
VDD
VDD
VDD
R1
C
R1
C
R2
C
R1
C
Microcontroller
R1
C
VDD
V1
V1
V2
V2
V3
V3
V4
V4
V5
V5
VDD
SEG0~SEG60
COM0~COM15
VSS
R3
Power Save Signal
TR1
VEE
Fig.19 LCD Bias circuit
2007 Jul 05
32 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
10 COMMON, SEGMENT OUTPUT VOLTAGE
The output voltage level of COMMON driver and SEGMENT driver is given in Table 36.
The output voltage level of COMMON driver is decided by the combination of Frame signal, internal COMMON
COUNTER output, and the Display ON/OFF register.
The output voltage level of SEGMENT driver is decided by the combination of Frame signal, Display Data, and the
Display ON/OFF register.
Table 36 COMMON/SEGMENT ouptut voltage level
FR
Data
DISPLAY
ON/OFF
SEG0~SEG60
(SEG0~SEG79)
COM0~COM15
L
L
ON
V3
V4
L
H
ON
V5
VDD
H
L
ON
V2
V1
H
H
ON
VDD
V5
x(don’t care)
x(don’t care)
OFF
V2 or V3
previous voltage
Note that, in the above table, “Data” for the COM0~COM15 is actually the output of the internal COMMON COUNTER,
which generates horizontal raster scanning signal.
During RESET, both SEGMENT and COMMON outputs are at VDD.
2007 Jul 05
33 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
11 ON-CHIP RC OSCILLATOR
The SBN1661G_M18 has an on-chip RC-type oscillator. All other three members of the family do not have on-chip
oscillator and need external clock source. The output CLK of the oscillator is the basic timing clock of the internal control
logic, display pixel rate, and is also used to generate frame signal.
The capacitor of the RC-oscillator is fabricated on-chip. Only an external resistor Rf needs to be connected across OSC1
and OSC2. The recommended value of Rf is in the range from 1000K ohm to 1200K ohm. During PCB layout, this resistor
should be placed as close to the SBN1661G_M18 as possible, such that stray capacitance, inductance, and resistance
can be minimized.
VDD
CLK
VDD
OSC1
OSC2
Disable
Disable
Disable
VSS
VSS
Rf
1.0 MΩ(typical)
Fig.20 On-chip RC oscillator
The characteristics of the oscillator is given is Table. 37.
Table 37 On-chip RC oscillator characteristics, Tamb = −20 to +75 °C
Oscillation
min.
typ.
max.
unit
Oscillation frequency at VDD=5V, Rf= 1.0 MΩ ±20%
17.6
21.5
25.9
KHz
Oscillation frequency at VDD=3V, Rf= 1.0 MΩ ±20%
15.7
19.1
22.8
KHz
2007 Jul 05
34 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
12 ELECTRICAL CHARACTERISTICS
12.1
Absolute maximum rating
Table 38 Absolute maximum rating
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
VDD
voltage on the VDD pin(pad)
−0.3
+7.0
Volts
VLCD (note 2)
LCD bias voltage, VLCD=VDD-V5
3.5
13
Volts
VI
input voltage on any pin with respect to VSS
−0.3
VDD + 0.3
Volts
PD
power dissipation
250
mW
Tstg
storage temperature range
−55
+125
°C
Tamb
operating ambient temperature range
-40
+ 85
°C
Tsol (note 3)
soldering temperature/time at pin
260 °C,
10 Second
Notes
1. The following applies to the Absolute Maximum Rating:
a) Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device.
b) The SBN1661G_X series includes circuitry specifically designed for the protection of its internal devices from the
damaging effect of excessive static charge (ESD). However, it is suggested that conventional precautions be
taken to avoid applying greater than the rated maxima.
c) Parameters are valid over operating temperature range unless otherwise specified.
d) All voltages are with respect to VSS, unless otherwise noted.
2. The condition VDD≥ V1 ≥ V2 ≥ V3 ≥ V4 ≥ V5 must always be met.
3. QFP-type packages are sensitive to moisture of the enviroment, please check the drypack indicator on the tray
package before soldering. Exposure to moisture longer than the rated drypack level may lead to cracking of the
plastic package or broken bonding wiring inside the chip.
2007 Jul 05
35 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
13 DC CHARACTERISTICS
Table 39 DC Characteristics
VDD = 5 V ±10%; VSS = 0 V; all voltages with respect to VSS, unless otherwise specified; Tamb = −20 to +75 °C.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
5.0
5.5
V
13
V
VDD
Supply voltage for logic
2.7
VLCD
LCD bias voltage VLCD= VDD-V5
3.5
VIL
LOW level input voltage
VIH
For all inputs
HIGH level input voltage
0 ~ 0.7
0 ~ 1.1
0 ~ 1.2
@vdd=2.7
@vdd=5.0
@vdd=5.5
For all inputs
2.0 ~ 2.7
3.5 ~ 5.0
3.7 ~ 5.5
@vdd=2.7
@vdd=5.0
@vdd=5.5
V
V
VOL
LOW level output voltage
For all outputs
0.0
0.3
V
VOH
HIGH level output voltage
For all outputs
VDD - 0.3
VDD
V
ISTBY
Standby current at V5=-5 volts
Note 1
3.0
μA
IDD(1)
Operating current at V5=-5 volts and
fCL=2KHz, VLCD=10 volts
2.7
5.6
μA
IDD(2)
Operating current at V5=-5 volts and
Rf=1 MΩ, VLCD=10 volts
12.3
15.6
μA
IDD(3)
Operating current at V5=-5 volts and
fCL=21.8 KHz, VLCD=10 volts
5.3
10.8
μA
IDD(4)
Operating current at V5=-5 volts and
tCYC=100 KHz, VLCD=10 volts
21.7
26.2
μA
fosc(VDD=5V),
fosc(VDD=3V)
Please refer to Table 37, On-chip RC oscillator characteristics.
Cin
Input capacitance of all input pins
5.0
8.0
pF
RON
LCD driver ON resistance
Note 5
5.0
7.5
KΩ
tR
Reset time
Note 6
Note 2 & Note 3
Note 4
1.0
μS
Notes:
1. Conditions for the measurement: OSC1=OSC2=VDD, measured at the VDD pin.
2. These values are measured when the microcontroller does not perform any READ/WRITE operation to the chip.
3. These meaurements are for different members of the series:
a) IDD(1) are measured for the SBN1661G_M02 and the SBN0080G_S02,
b) IDD(2) are measured for the SBN1661G_M18, and
c) IDD(3) are measured for the SBN0080G_S18.
4. These values are measured when the microcontroller continuously performs READ/WRITE operation to the chip.
5. This measurement is for the transmission high-voltage PMOS or NMOS of COM0~15 and SEG0~60(79). Please
refer to Section 18 for these driver circuit. The meaurement is for the case when the voltage differential between the
source and the drain of the high voltage PMOS or NMOS is 0.1 volts.
6. The value is relative to the RESET pulse edge. That is, 1.0 μS after the last RESET edge, the device is completely
reset.
2007 Jul 05
36 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
14 AC TIMING CHARACTERISTICS
14.1
CL and FR timing
TF
TR
TWHCL
CL
TWLCL
0.1 x VDD
0.9 x VDD
0.1 x VDD
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
TDFR
FR
0.1 x VDD
Fig.21 Display Control Signal Timing
Table 40 CL and FR timing characteristics at VDD=5 volts
VDD = 5 V ±10%; VSS = 0 V; all voltages with respect to VSS unless otherwise specified; Tamb = −20 to +75 °C.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
TWHCL
CL clock high pulse width
33
μs
TWLCL
CL cock low pulse width
33
μs
TR
CL clock rise time
28
120
ns
TF
CL clock fall time
28
120
ns
TDFR(input)
FR delay time (input)
When used as input in
Slave Mode application
0.2
1.6
μS
TDFR(output)
FR delay time (output)
When used as output in
Master Mode application,
with CL= 100 pF.
0.2
0.36
μS
-2.0
Table 41 CL and FR timing characteristics at VDD=3 volts
VDD = 3 V ±10%; VSS = 0 V; all voltages with respect to VSS unless otherwise specified; Tamb = −20 to +75 °C.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
TWHCL
CL clock high pulse width
65
μs
TWLCL
CL cock low pulse width
65
μs
TR
CL clock rise time
TF
CL clock fall time
TDFR(input)
FR delay time (input)
When used as input in
Slave Mode application
TDFR(output)
FR delay time (output)
When used as output in
Master Mode application,
with CL= 100 pF.
2007 Jul 05
37 of 52
-3.6
50
220
ns
50
220
ns
0.36
3.6
μS
0.32
0.6
μS
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
14.2
AC timing for interface with an 80-type microcontroller
C/D, CS
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
tAS
tAH
tF
tR
tRWPW
RD, WR
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
tCYC
tDH
tDS
D0 to D7
(WRITE)
Hi-Z
D0 to D7
(READ)
Hi-Z
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
Hi-Z
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
tACC
Hi-Z
tOH
Fig.22 AC timing for interface with a 80-type microcontroller
Table 42 AC timing for interface with a 80-type microcontorller at VDD=5 volts
VDD = 5 V ±10%; VSS = 0 V; Tamb = -20 °C to +75°C.
symbol
parameter
min.
max.
test conditons
tAS
Address set-up time
20
tAH
Address hold time
10
tF, tR
Read/Write pulse falling/rising time
tRWPW
Read/Write pulse width
200
ns
tCYC
System cycle time
1000
ns
tDS
Data setup time
80
ns
tDH
Data hold time
10
ns
tACC
Data READ access time
tOH
Data READ output hold time
ns
ns
15
10
unit
ns
90
CL= 100 pF.
ns
60
Refer to Fig. 23.
ns
test conditons
unit
Table 43 AC timing for interface with an 80-type microcontorller at VDD=3 volts
VDD = 3 V ±10%; VSS = 0 V; Tamb = -20 °C to +75°C.
symbol
parameter
min.
tAS
Address set-up time
40
tAH
Address hold time
20
tF, tR
Read/Write pulse falling/rising time
tRWPW
Read/Write pulse width
400
ns
tCYC
System cycle time
2000
ns
tDS
Data setup time
160
ns
2007 Jul 05
max.
ns
ns
15
38 of 52
ns
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
symbol
parameter
min.
tDH
Data hold time
20
tACC
Data READ access time
tOH
Data READ output hold time
20
max.
test conditons
unit
180
CL= 100 pF,
ns
120
Refer to 23.
ns
ns
Note:
The measurement is with the load circuit connected. The load circuit is shown in Fig. 23.
Pin
CL
CL= 100 pF (including wiring and
probe capacitance).
VSS
2007 Jul 05
Fig.23 Load circuit.
39 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
14.3
AC timing for interface with a 68-type microcontroller
tCYC
tF
tR
E
0.9 x VDD
0.9 x VDD
tEW
0.1 x VDD
0.1 x VDD
0.1 x VDD
tAS1
R/W
tAH1
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
tAS2
C/D, CS
tAH2
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
tDH
tDS
D0 to D7
(WRITE)
Hi-Z
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
tACC
D0 to D7
(READ)
Hi-Z
Hi-Z
tOH
0.9 x VDD
0.9 x VDD
0.1 x VDD
0.1 x VDD
Hi-Z
Fig.24 AC timing for interface with a 68-type microcontroller
Table 44 AC timing for interface with a 68-type microcontroller at VDD=5 volts
VDD = 5 V ±10%; VSS = 0 V; Tamb = -20 °C to +75°C.
symbol
parameter
min.
tAS1
Address set-up time with respect to R/W
20
ns
tAS2
Address set-up time with respect to C/D, CS
20
ns
tAH1
Address hold time with respect to R/W
10
ns
tAH2
Address hold time respect with to C/D, CS
10
ns
tF, tR
Enable (E) pulse falling/rising time
tCYC
System cycle time
1000
tEWR
Enable pulse width for READ
100
ns
tEWW
Enable pulse width for WRITE
80
ns
tDS
Data setup time
80
ns
tDH
Data hold time
10
tACC
Data access time
tOH
Data output hold time
2007 Jul 05
max.
test conditons
15
10
40 of 52
unit
ns
Note 1
ns
ns
90
CL= 100 pF.
ns
60
Refer to Fig. 23.
ns
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
Table 45 AC timing for interface with a 68-type microcontroller at VDD=3 volts
VDD = 3 V ±10%; VSS = 0 V; Tamb = -20 °C to +75°C.
symbol
parameter
min.
max.
test conditons
unit
tAS1
Address set-up time with respect to R/W
40
ns
tAS2
Address set-up time with respect to C/D, CS
40
ns
tAH1
Address hold time with respect to R/W
20
ns
tAH2
Address hold time respect with to C/D, CS
20
ns
tF, tR
Enable (E) pulse falling/rising time
tCYC
System cycle time
2000
tEWR
Enable pulse width for READ
200
ns
tEWW
Enable pulse width for WRITE
160
ns
tDS
Data setup time
160
ns
tDH
Data hold time
20
ns
tACC
Data access time
tOH
Data output hold time
15
20
ns
Note 1
ns
180
CL= 100 pF.
ns
120
Refer to Fig. 23.
ns
Note:
1. The system cycle time(tCYC) is the time duration from the time when Chip Enable is enabled to the time when Chip
Select is released.
2007 Jul 05
41 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
15 MICROCONTROLLER INTERFACE CIRCUIT
15.1
Example for interface with a 80-family microcontroller
VDD
VDD
VDD
A0
Note:
This example is applicable
to the SBN1661G_M02.
C/D
A1~A7
IORQ
80-family
Microcontroller
DECODER
CS
SBN1661G_M02
D0~D7
DB0~DB7
RD
RD
WR
WR
RES
RESET/IF
VSS
GND
V5
RESET
Negative
LCD bias voltage
Fig.25 Interface example with an 80-family microcontroller
15.2
Example for interface with a 68-family microcontroller
VDD
VDD
VDD
A0
Note:
This example is applicable
to the SBN1661G_M02.
The CS selection for the
SBN0080G_S18 and the
SBN0080G_S02 can be
decoded from the address
lines in the same way. For
application with the
SBN1661G_M18, which
does not have a CS input,
the CS output from the
decoder must be ORed with
C/D, E, and R/W.
C/D
A1~A15
VMA
68-family
Microcontroller
DECODER
CS
SBN1661G_M02
D0~D7
DB0~DB7
E
E
R/W
R/W
RES
RESET/IF
VSS
GND
V5
RESET
Negative
LCD bias voltage
Fig.26 Interface example with a 68-family microcontroller
2007 Jul 05
42 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
15.3
Example for interface with other types of 8-bit microcontroller
VDD
VDD
Note:
This example is applicable
only to the SBN1661G_M18,
which does not have a CS
input and the CS output from
the address or I/O space
decoding circut must be
ORed with C/D, RD(E), and
(WR)R/W.
C/D
Address
8-bit
Microcontroller
VDD
(indicating commad/data)
C/D
Address or
I/O space
decoding
D0~D7
SBN1661G_M18
DB0~DB7
RD(E)
E
WR(R/W)
R/W
RESET/IF
VSS
RES
GND
V5
RESET
Negative
LCD bias voltage
Fig.27 Interface example with an 8-bit microcontroller
2007 Jul 05
43 of 52
data sheet (v6.4)
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Avant Electronics
Dot-matrix STN LCD Driver with 32-row x 80-column
16 SYNCHRONIZATION OF CLOCK AND FRAME IN MASTER/SLAVE CONNECTIONS
To expand COMMON/SEGMENT number, both the SBN1661G_M18 and the SBN1661G_M02 can be used Master.
They can also be used as Slave. However, if the SBN1661G_M02 is used as Master, external clock source is needed,
as it has no on-chip oscillator.
In master/slave connections, clock and frame between the master and its slaves must be in synchronization.
The SBN0080G_S18 and the SBN0080G_S02 can be used only as Slave for SEGMENT expansion.
16.1
SBN1661G_M18 connected with a SBN1661G_M18
To LCD SEGMENT
To LCD SEGMENT
SBN1661G_M18
SBN1661G_M18
To LCD COMMON
To LCD COMMON
VDD
Master
M/S
Slave
M/S
OSC1 OSC2
FR
OSC1 OSC2
VSS
FR
Rf
Fig.28 SBN1661G_M18 connected with a SBN1661G_M18.
16.2
SBN1661G_M18 connected with more than two SBN0080G_S18
To LCD SEGMENT
VDD
To LCD SEGMENT
SBN1661G_M18
SBN0080G_S18
To LCD SEGMENT
SBN0080G_S18
To LCD COMMON
M/S
Master
OSC1 OSC2
Rf
Slave
FR
CL
Slave
FR
CL
FR
CMOS buffer
Note: when more than two slaves are connected, a CMOS
clock buffer is needed to drive all the slaves. The duty and
phase of the clock to all the slaves must be the same as that
for the master.
Fig.29 SBN1661G_M18 connected with more than two SBN0080G_S18
2007 Jul 05
44 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
16.3
SBN1661G_M02 connected with a SBN1661G_M02
To LCD SEGMENT
To LCD SEGMENT
SBN1661G_M02
SBN1661G_M02
M/S
Master
M/S
CL
FR
External
clock source
16.4
To LCD COMMON
To LCD COMMON
VDD
VSS
Slave
CL
FR
Fig.30 SBN1661G_M02 connected with a SBN1661G_M02.
SBN1661G_M02 connected with a SBN0080G_S02
To LCD SEGMENT
To LCD SEGMENT
SBN1661G_M02
SBN0080G_S02
To LCD COMMON
VDD
M/S
Master
CL
Slave
FR
External
clock source
2007 Jul 05
CL
FR
Fig.31 SBN1661G_M02 connected with a SBN0080G_S02.
45 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
17 TYPICAL APPLICATIONS
17.1
1/16 duty, 10 characters x 2 lines
COM0
16 x 61 LCD Panel
In this application,
10-characters x 2-lines can be
displayed, if the format of
character font is 6 x 8 pixels.
COM15
SEG0
SEG60
SEG0
SEG60
COM15
SBN1661G_M18
COM0
Fig.32 1/16 duty, 10 characters x 2 lines
17.2
1/16 duty, 23 characters x 2 rows
COM0
16 x 141 LCD Panel
COM15
In this application,
23-characters x 2-lines
can be displayed, if the
format of character font is
6 x 8 pixels.
SEG0
SEG60
SEG0
SEG60
SEG61
SEG0
SEG140
SEG79
FR
COM15
SBN0080G_S18
SBN1661G_M18
(slave)
CL
(master)
COM0
Fig.33 1/16 duty, 23 characters x 2 lines
17.3
1/32 duty, 33 characters x 4 lines
COM0
COM15
32 x 202 LCD Panel
COM16
COM31
SEG0
SEG0
SEG60
SEG60
SEG0
SBN1661G_M18
(master)
SEG141 SEG201
SEG79
SEG0
FR
SBN0080G_S18
CL
(slave)
In this application, 33-characters x 4-lines can be
displayed, if the format of character font is 6 x 8 pixels.
2007 Jul 05
SEG140
FR
COM15
COM0
SEG61
46 of 52
CL
SEG60
COM0
SBN1661G_M18
(slave)
COM15
Fig.34 1/32 duty, 33 characters x 4 lines
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
18 PIN CIRCUITS
Table 46 MOS-level schematics of all input, output, and I/O pins.
SYMBOL
Input/
output
CIRCUIT
NOTES
VDD
C/D,
R/W(WR),
E/RD,
RESET/IF
Inputs
VSS
VDD
M/S
Input
VSS
VDD
CLK
VDD
OSC1
OSC2
OSC1, OSC2
Disable
Disable
Disable
The circuit encircled
inside the red dashed
frame is the oscillator
circut.
VSS
VSS
VDD
Enable
VDD
Output Enable
D0~D7, FR
I/O
Data out
VSS
VSS
Data in
2007 Jul 05
47 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
SYMBOL
Input/
output
CIRCUIT
VDD
EN1
NOTES
VDD
SEG0~79
VDD
V5
VDD
EN2
V5
V2
SEG0~79
V5
VDD
EN3
VDD
EN4
V3
V5
V5
V5
VDD
EN1
VDD
COM0~15
VDD
V5
VDD
EN2
V5
V1
COM0~15
V5
VDD
EN3
VDD
EN4
V4
V5
V5
V5
2007 Jul 05
48 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
19 APPLICATION NOTES
1. It is recommended that the following power-up sequence be followed to ensure reliable operation of your display
system. As the ICs are fabricated in CMOS and there is intrinsic latch-up problem associated with any CMOS
devices, proper power-up sequence can reduce the danger of triggering latch-up. When powering up the system,
control logic power must be powered on first. When powering down the system, control logic must be shut off later
than or at the same time with the LCD bias (VEE).
1 second (minimum)
1 second (minimum)
5V
VDD
0V
0~50 ms
0~50 ms
Signal
VEE
0 second
(minimum)
0 second
(minimum)
-30V
Fig.35 Recommended power up/down sequence
2. The metal frame of the LCD panel should be grounded.
3. A 0.1 μF ceramic capacitor should be connected between VDD and VSS.
4. A 0.1 mF ceramic capacitor should be connected between VDD (or VSS) and each of V1, V2, V3, V4, and V5.
5. If the length of the cable connecting the host microcontroller and the LCD module is longer than 45 cm, a ceramic
capacitor of 20P~150P should be connected between VDD (or VSS) and each of the R/WR(WR), the E/RD, and the
CS.
2007 Jul 05
49 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
20 PACKAGE INFORMATION
Pakage information is provided in another
document. Please contact Avant Electronics for
package information.
2007 Jul 05
50 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
21 SOLDERING
21.1
Introduction
There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and
surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for
surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often
used.
This text gives a very brief insight to a complex technology. For more in-depth account of soldering ICs, please refer to
dedicated reference materials.
21.2
Reflow soldering
Reflow soldering techniques are suitable for all QFP packages.
The choice of heating method may be influenced by larger plastic QFP packages (44 leads, or more). If infrared or vapour
phase heating is used and the large packages are not absolutely dry (less than 0.1% moisture content by weight),
vaporization of the small amount of moisture in them can cause cracking of the plastic body. For more information, please
contact Avant for drypack information.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the
printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between
50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 °C.
Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 °C.
21.3
Wave soldering
Wave soldering is not recommended for QFP packages. This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following conditions must be observed:
• A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering
technique should be used.
• The footprint must be at an angle of 45° to the board direction and must incorporate solder thieves
downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured.
Maximum permissible solder temperature is 260 °C, and maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within 6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications.
21.4
Repairing soldered joints
Fix the component by first soldering two diagonally- opposite end leads. Use only a low voltage soldering iron (less
than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a
dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C.
2007 Jul 05
51 of 52
data sheet (v6.4)
Avant Electronics
SBN1661G_M18, SBN1661G_M02, SBN0080G_S18, SBN0080G_S02
Dot-matrix STN LCD Driver with 32-row x 80-column
22 LIFE SUPPORT APPLICATIONS
Avant’s products, unless specifically specified, are not designed for use in life support appliances, devices, or systems
where malfunction of these products can reasonably be expected to result in personal injury. Avant customers using or
selling Avant’s products for use in such applications do so at their own risk and agree to fully indemnify Avant for any
damages resulting from such improper use or sale.
2007 Jul 05
52 of 52
data sheet (v6.4)