967 KB

The following document contains information on Cypress products.
FUJITSU MICROELECTRONICS
DATA SHEET
DS07-12509-8E
8-bit Proprietary Microcontroller
CMOS
F2MC-8L MB89120/120A Series
MB89121/123A/125A/P131/P133A/P135A
MB89PV130A
■ DESCRIPTION
The MB89120 series is a line of single-chip microcontrollers containing a compact instruction set and a great
variety of peripheral functions such as a timer, serial interface, and external interrupt. The MB89120A series is
an extended variant of the MB89120, with a remote control transmission function and wake-up interrupt function.
■ FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
F2MC-8L family CPU core
Low-voltage operation
Low current consumption (allowing for dual clock)
Minimum execution time : 0.95 µs at 4.2 MHz
21-bit time-base counter
I/O ports : Max. 36 ports
External interrupts : 3 channels
External interrupts (wake-up function) : 8 channels (only for the MB89120A series)
8-bit serial I/O : 1 channel
8/16-bit timer/counter : 1 channel
Built-in remote-control transmitting frequency generator (only for the MB89120A series)
Low-power consumption modes (stop mode, sleep mode, watch mode)
Package : QFP-48
CMOS technology
For the information for microcontroller supports, see the following web site.
http://edevice.fujitsu.com/micom/en-support/
Copyright©2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2008.12
MBMB89120/120A Series
■ PRODUCT LINEUP
Part number
Item
MB89121
MB89123A
MB89125A
Mass-produced products
(Mask ROM products)
Classification
ROM size
4 K × 8 bits
(internal mask
ROM)
RAM size
128 × 8 bits
8 K × 8 bits
(internal mask
ROM)
MB89P131
One-time products
16 K × 8 bits
(internal mask
ROM)
8 K × 8 bits
4 K × 8 bits
(Internal PROM to (Internal PROM
be programmed to be programmed
with a generalwith a generalpurpose EPROM purpose EPROM
programmer)
programmer)
256 × 8 bits
CPU functions
The number of instructions
Instruction bit length
Instruction length
Data bit length
Minimum execution time
Minimum interrupt processing time
Ports
Output ports (N-ch open-drain)
Output ports (CMOS)
I/O ports (CMOS)
Total
128 × 8 bits
: 136
: 8 bits
: 1 to 3 bytes
: 1, 8, 16 bits
: 0.95 µs at 4.2 MHz
: 8.57 µs at 4.2 MHz
: 4 (All also serves as peripherals.)
:8
: 24 (8 ports also serve as peripherals.)
: 36
8-bit timer/counter × 2 channels or 16-bit event counter × 1 channel
Timer/counter
8 bits
LSB/MSB first selectable
Serial I/O
External interrupt 1
MB89P133A
3 independent channels (edge selection, interrupt vector, source flag)
Rising edge/falling edge/both edges selectable
Also for wake-up from stop/sleep mode (edge detection is also permitted in stop mode)
External interrupt 2
(wake-up function)
⎯
8 channels (only for level detection)
⎯
Remote control
transmitting frequency generator
⎯
1 channel
(pulse width and frequency selectable
by program)
⎯
Standby mode
Process
Operating voltage*
EPROM for use
Sleep mode, stop mode, watch mode
CMOS
2.2 V to 4.0 V (with the dual clock option)
2.2 V to 6.0 V (with the single clock option)
2.7 V to 6.0 V
⎯
* : Varies with conditions such as operating frequencies. (See “■ ELECTRICAL CHARACTERISTICS”.)
(Continued)
2
DS07-12509-8E
MBMB89120/120A Series
(Continued)
Part number
MB89P135A
MB89PV130A
One-time PROM product
Piggyback/evaluation product
ROM size
16 K × 8 bits
(internal PROM, to be programmed with
general-purpose EPROM programmer)
32 K × 8 bits
(external ROM)
RAM size
512 × 8 bits
1 K × 8 bits
Item
Classification
CPU functions
The number of instructions
Instruction bit length
Instruction length
Data bit length
Minimum instruction execution time
Minimum interrupt processing time
: 136
: 8 bits
: 1 to 3 bytes
: 1, 8, 16 bits
: 0.95 µs at 4.2 MHz
: 8.57 µs at 4.2 MHz
Ports
Output ports (N-ch open-drain ports)
Output ports (CMOS)
I/O ports (CMOS)
Total
: 4 (All also serve as peripherals.)
:8
: 24 (8 ports also serve as peripherals.)
: 36
Timer/counter
8-bit timer/counter × 2 channels or 16-bit event counter × 1 channel
8 bits
LSB/MSB first selectable
Serial I/O
External interrupt 1
3 independent channels (edge selection, interrupt vector, source flag)
Rising/falling/both edges selectable
Used also for wake-up from stop/sleep mode. (Edge detection is also permitted in stop
mode.)
External interrupt 2
(wake-up function)
8 channels (only for level detection)
Remote control
transmitting frequency generator
1 channel (Pulse width and cycle selectable by program)
Standby mode
Sleep mode, stop mode, and watch mode
Process
Operating voltage
EPROM for use
DS07-12509-8E
CMOS
2.7 V to 6.0 V
2.7 V to 6.0 V
⎯
MBM27C256A-20TVM
3
MBMB89120/120A Series
■ PACKAGE AND CORRESPONDING PRODUCTS
Package
MB89121
MB89123A
MB89125A
MB89P133A
MB89P131
×
×
×
×
×
MB89P135A
MB89PV130A
FPT-48P-M13
MQP-48C-P01
Package
×
FPT-48P-M13
MQP-48C-P01
×
: Available, × : Not available
Note : Package details of OTPROM products and piggyback/evaluation products are common to those of MB89130/
130A series. Refer to the MB89130/130A series data sheet for details.
■ DIFFERENCES AMONG PRODUCTS
1. Memory Size
Before evaluating using the one-time ROM product, verify its difference from the product that will actually be
used. Take particular care on the following points :
• The available number of register banks is different among the MB89121, the MB89123A/125A, and P135A/
PV130A.
• The stack area, etc., is set at the upper limit of the RAM.
2. Current Consumption
• When operated at low-speed, a product with an OTPROM (EPROM) will consume more current than a product
with a mask ROM. However, the current consumption in the sleep/stop mode is the same. (For more information, see “■ ELECTRICAL CHARACTERISTICS”.)
• In the case of the MB89PV130A, added is the current consumed by the EPROM which is connected to the
top socket.
3. Mask Options
Functions that can be selected as options and how to designate these options vary with product.
Before using options, check “■ MASK OPTIONS”.
Take particular care on the following point :
• Pull-up resistor cannot be set for P40 to P43 on the MB89P135A.
• Options are fixed on the MB89PV130A.
4
DS07-12509-8E
MBMB89120/120A Series
■ PIN ASSIGNMENT
1
2
3
4
5
6
7
8
9
10
11
12
36
35
34
33
32
31
30
29
28
27
26
25
P36/INT2
P37/BZ/(RCO)
P00/(INT20)
P01/(INT21)
P02/(INT22)
P03/(INT23)
P04/(INT24)
P05/(INT25)
P06/(INT26)
P07/(INT27)
P10
P11
P24
P23
P22
P21
P20
P17
VSS
P16
P15
P14
P13
P12
AVCC
RST
MOD0
MOD1
X0
X1
VCC
X0A
X1A
P27
P26
P25
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
P40
P41
P42
P43
AVR
AVSS
P30/SCK
P31/SO
P32/SI
P33/EC/SCO
P34/TO/INT0
P35/INT1
(TOP VIEW)
(FPT-48P-M13)
Note : Parenthesized function is available only for the MB89120A series.
DS07-12509-8E
5
MBMB89120/120A Series
■ PIN DESCRIPTION
Pin no.
Pin name
5
X0
6
X1
8
X0A
9
X1A
3
MOD0
4
MOD1
Circuit type
Function
A
Main clock crystal oscillator pins (max. 4.2 MHz)
B
Sub clock crystal oscillator pins (for 32.768 kHz)
C
Operation mode select pins
Connect these pins directly to VSS.
D
Reset I/O pin
This port is of N-ch open-drain output type with pull-up resistor and a hysteresis input type. The internal circuit is initialized by the input of “L”. “L” is output from this pin by an
internal reset source as optional setting.
2
RST
27 to 34
P07/ (INT27) to
P00/ (INT20)
I
General-purpose I/O ports
On the MB89120A series, these pins also serve as external interrupt input.
External interrupt input pins are hysteresis input.
18, 20 to 26
P17 to P10
E
General-purpose I/O ports
10 to 17
P27 to P20
G
General-purpose output-only ports
42
P30/SCK
F
General-purpose I/O port
Also serves as clock I/O for the 8-bit serial I/O interface.
This port is of hysteresis input type.
41
P31/SO
F
General-purpose I/O port
Also serves as a serial I/O data output. This port is hysteresis input type.
40
P32/SI
F
General-purpose I/O port
Also serves as a serial I/O data input. This port is hysteresis input type.
F
General-purpose I/O port
Also serves as the external clock input for the 8-bit timer/
counter. This port is hysteresis input type.
System clock output is optional.
39
P33/EC/SCO
38
P34/TO/INT0
F
General-purpose I/O port
Also serves as the overflow output and external
interrupt input for the 8-bit timer/counter. This port is
hysteresis input type.
36,
37
P36/INT2,
P35/INT1
F
General-purpose I/O ports
Also serve as an external interrupt input. These ports are
hysteresis input type.
F
General-purpose I/O port
Also serves as a buzzer output. This port is hysteresis
input type. On the MB89120A series, the pin also serves
as a remote control output.
35
P37/BZ/ (RCO)
(Continued)
6
DS07-12509-8E
MBMB89120/120A Series
(Continued)
Pin no.
Pin name
Circuit type
45 to 48
P43 to P40
H
N-ch open-drain output ports
7
VCC
—
Power supply pin
19
VSS
—
Power supply (GND) pin
1
AVCC
—
Power supply pin
Use this pin at the same voltage as VCC.
44
AVR
—
Reference voltage input pin
43
AVSS
—
Power supply (GND) pin
Use this pin at the same voltage as VSS.
DS07-12509-8E
Function
7
MBMB89120/120A Series
■ I/O CIRCUIT TYPE
Type
Circuit
A
Remarks
• Crystal and ceramic oscillation type (main clock)
Cricuit for the MB89P133A/P131/P135A/PV130A
• External clock input select versions of MB89121/
123A/125A
At an oscillation feedback resistor of approximately
1 MΩ / 5 V
X1
X0
Standby control signal
• Crystal and ceramic oscillation type (main clock)
• Crystal or ceramic oscillator select versions of
MB89121/123A/125A
At an oscillation feedback resistor of approximately
1 MΩ / 5 V
X1
X0
Standby control signal
B
• Crystal and ceramic oscillation type (sub clock)
Circuit for the MB89121/123A/125A
At an oscillation feedback resistor of approximately
4.5 MΩ / 5 V
X1A
X0A
Standby control signal
• Crystal and ceramic oscillation type (sub clock)
Circuit for the MB89P131/P133A/P135A/PV130A
At an oscillation feedback resistor of approximately
4.5 MΩ / 5 V
X1A
X0A
Standby control signal
C
D
R
P-ch
• Output pull-up resistor (P-ch) of approximately
50 kΩ / 5 V
• Hysteresis input
N-ch
(Continued)
8
DS07-12509-8E
MBMB89120/120A Series
(Continued)
Type
Circuit
Remarks
E
• CMOS output
• CMOS input
• Pull-up resistor optional
R
P-ch
P-ch
N-ch
F
R
• CMOS output
• Hysteresis input
• Pull-up resistor optional
P-ch
P-ch
N-ch
G
• CMOS output
P-ch
N-ch
H
• N-ch open-drain output
• Pull-up resistor optional
R
P-ch
P-ch
N-ch
I
• CMOS output
• CMOS input
• The interrupt input is a hysteresis input (available
only for the MB89120A series) .
• Pull-up resistor optional
R
P-ch
P-ch
N-ch
Interrupt input
Only for the MB89120A series
DS07-12509-8E
9
MBMB89120/120A Series
■ HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high- withstand voltage pins, or if higher than the voltage which shows on “1. Absolute
Maximum Ratings” in “■ ELECTRICAL CHARACTERISTICS” is applied between VCC and VSS.
When latchup occurs, power supply current increases rapidly, and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AVCC and AVR) and analog input from exceeding the digital
power supply (VCC) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to pull-up or pull-down
resistor.
3. Treatment of N.C. Pins
Be sure to leave N.C. (internally connected) pins open.
4. Power Supply Voltage Fluctuations
Although operation is assured within the rated range of VCC power supply voltage, a rapid fluctuation of the
voltage could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC
is therefore important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60 Hz)
and the transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when
power is switched.
5. Precautions when Using an External Clock
When an external clock is used, oscillation stabilization time is required even for power-on reset (optional) and
release from stop mode.
6. Turning on the supply voltage (only for the MB89P135A)
When the power supply is turned on if MB89P135A is used, power on sharply up to 2.0 V within 13 clock cycles
after starting of oscillation.
Further, various options may not be set , if power supply is turned on without the above condition.
10
DS07-12509-8E
MBMB89120/120A Series
■ PROGRAMMING TO THE PROM ON THE MB89P131
The MB89P131 is a one-time PROM version of the MB89121.
1. Features
• 4-Kbyte PROM on chip
• Equivalency to the MBM27C256A in EPROM mode (when programmed with the EPROM programmer)
2. Memory Space
Memory space in EPROM mode is diagrammed below :
Address
Single chip
EPROM mode
(Corresponding addresses in the EPROM programmer)
0000H
I/O
Not available
RAM
0000H
Not available
F000H
Not available
7000H
EPROM
4 KB
PROM
4 KB
FFFFH
7FFFH
3. Programming to the PROM
In EPROM mode the MB89P131 functions equivalent to the MBM27C256A. This allows the PROM to be
programmed with a general-purpose EPROM programmer by using the dedicated socket adapter. Note, however, that the electronic signature mode cannot be used.
• Programming procedure
(1) Set the EPROM programmer to MBM27C256A.
(2) Load program data into the EPROM programmer at 7000H to 7FFFH (note that addresses F000H to
FFFFH while operating as a single chip correspond to 7000H to 7FFFH in EPROM mode) .
(3) Program with the EPROM programmer.
DS07-12509-8E
11
MBMB89120/120A Series
■ PROGRAMMING TO THE PROM ON THE MB89P133A
The MB89P133A is a one-time PROM version of the MP89123A.
1. Features
• 8-Kbyte PROM on chip
• Equivalency to the MBM27C256A in EPROM mode (when programmed with the EPROM programmer)
2. Memory Space
Memory space in EPROM mode is diagrammed below :
Address
Single chip
EPROM mode
(Corresponding addresses in the EPROM programmer)
0000H
I/O
RAM
0000H
Not available
E000H
Not available
6000H
PROM
8 KB
FFFFH
EPROM
8 KB
7FFFH
3. Programming to the PROM
In EPROM mode the MB89P133A functions equivalent to the MBM27C256A, This allows the PROM to be
programmed with a general-purpose EPROM programmer by using the dedicated socket adapter. Note, however, that the MB89P133A cannot use the electronic signature mode.
• Programming procedure
(1) Set the EPROM programmer to MBM27C256A.
(2) Load program data into the EPROM programmer at 6000H to 7FFFH (note that addresses E000H to
FFFFH while operating as a single chip correspond to 6000H to 7FFFH in EPROM mode) .
(3) Program with the EPROM programmer.
12
DS07-12509-8E
MBMB89120/120A Series
■ PROGRAMMING TO THE PROM ON THE MB89P135A
The MB89P135A is an OTPROM version of the MB89123A/125A.
1. Features
• 16-Kbyte PROM on chip
• Equivalency to the MBM27C256A in EPROM mode (when programmed with the EPROM programmer)
2. Memory Space
Memory space in EPROM mode is diagrammed below.
Address
Single chip
0000H
EPROM mode
(Corresponding addresses on the EPROM programmer)
I/O
0080H
RAM
0280H
Not available
8000H
0000H
Vacancy
(Read value FFH)
Not available
BFF0H
3FF0H
Option area
Not available
BFF6H
3FF6H
Vacancy
(Read value FFH)
Not available
C000H
4000H
PROM
16 KB
FFFFH
EPROM
16 KB
7FFFH
3. Programming to the PROM
In EPROM mode, the MB89P135A functions equivalent to the MBM27C256A. This allows the PROM to be
programmed with a general-purpose EPROM programmer (the electronic signature mode cannot be used) by
using the dedicated socket adapter.
• Programming procedure
(1) Set the EPROM programmer to the MBM27C256A.
(2) Load program data into the EPROM programmer at 4000H to 7FFFH (note that addresses C000H to
FFFFH while operating as a single chip correspond to 4000H to 7FFFH in EPROM mode) .
(3) Load option data into the EPROM programmer at 3FF0H to 3FF6H.
(4) Program with the EPROM programmer.
DS07-12509-8E
13
MBMB89120/120A Series
4. Setting PROM Options (MB89P135A Only)
The programming procedure is the same as that for the PROM. Options can be set by programming values at
the addresses shown on the memory map. The relationship between bits and options is shown on the following
bit map :
• PROM option bit map
Address
bit 7
Vacancy
3FF0H
bit 6
Vacancy
bit 5
Vacancy
bit 4
Clock mode
selection
Reset pin
output
1 : Single
clock
1 : Yes
0 : Dual
0 : No
clock
Readable Readable
and
and
writable
writable
Readable
and
writable
3FF1H
P07
Pull-up
1 : Yes
0 : No
P06
Pull-up
1 : Yes
0 : No
P05
Pull-up
1 : Yes
0 : No
P04
Pull-up
1 : Yes
0 : No
3FF2H
P17
Pull-up
1 : Yes
0 : No
P16
Pull-up
1 : Yes
0 : No
P15
Pull-up
1 : Yes
0 : No
3FF3H
P37
Pull-up
1 : Yes
0 : No
P36
Pull-up
1 : Yes
0 : No
Vacancy
Vacancy
3FF4H
3FF5H
3FF6H
bit 3
bit 2
bit 1
bit 0
Oscillation
stabilization time
Power-on
reset
1 : Yes
0 : No
00 : 22/FCH 10 : 216/FCH
01 : 212/FCH 11 : 218/FCH
P03
Pull-up
1 : Yes
0 : No
P02
Pull-up
1 : Yes
0 : No
P01
Pull-up
1 : Yes
0 : No
P00
Pull-up
1 : Yes
0 : No
P14
Pull-up
1 : Yes
0 : No
P13
Pull-up
1 : Yes
0 : No
P12
Pull-up
1 : Yes
0 : No
P11
Pull-up
1 : Yes
0 : No
P10
Pull-up
1 : Yes
0 : No
P35
Pull-up
1 : Yes
0 : No
P34
Pull-up
1 : Yes
0 : No
P33
Pull-up
1 : Yes
0 : No
P32
Pull-up
1 : Yes
0 : No
P31
Pull-up
1 : Yes
0 : No
P30
Pull-up
1 : Yes
0 : No
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Readable Readable
and
and
writable
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Readable Readable
and
and
writable
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Vacancy
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Readable
and
writable
Vacancy
Vacancy
Readable Readable
and
and
writable
writable
Note : Each bit is set to “1” as the initialized value, therefore the pull-up option is selected.
14
DS07-12509-8E
MBMB89120/120A Series
■ HANDLING MB89P131/P133A/P135A
1. Recommended Screening Conditions
High-temperature aging is recommended as the pre-assembly screening procedure.
Program, verify
Aging
+150 °C, 48 h
Data verification
Assembly
2. Programming Yield
Due to its nature, bit programming test cannot be conducted as Fujitsu delivery test. For this reason, a programming yeild of 100% cannot be assured at all times.
DS07-12509-8E
15
MBMB89120/120A Series
■ PROGRAMMING TO THE EPROM WITH PIGGYBACK/EVALUATION DEVICE
1. EPROM for Use
MBM27C256A-20TVM
2. Memory Space
Memory space in each mode, such as 32-Kbyte EPROM is diagrammed below.
Address
Single chip
Corresponding addresses on the EPROM programmer
0000 H
I/O
0080 H
RAM
0480 H
Not available
8000 H
0000 H
PROM
32 KB
FFFFH
EPROM
32 KB
7FFFH
3. Programming to the EPROM
(1)
(2)
(3)
16
Set the EPROM programmer for the MBM27C256A.
Load program data into the EPROM programmer at 0000H to 7FFFH.
Program with the EPROM programmer.
DS07-12509-8E
MBMB89120/120A Series
■ BLOCK DIAGRAM
X0
X1
X0A
X1A
Main clock oscillator
Time-base timer
Clock controller
Reset circuit
(WDT)
RST
8
8-bit timer/counter
P34/TO/INT0
8-bit timer/counter
P33/EC/SCO
External interrupt∗
(Wake-up)
8
Port 2
External interrupt
P20 to P27
P30/SCK
P32/SI
P31/SO
8-bit serial I/O
P10 to P17
Port 3
P00/(INT20) to 8
P07/(INT27)
Port 0/1
CMOS I/O port
Internal bus
Sub clock oscillator
(32.768 kHz)
P35/INT1
Remote control
transmission
frequency generator∗
CMOS output port
P36/INT2
Buzzer output
P37/BZ/(RCO)
CMOS I/O port
N-ch open-drain output port
F 2 M C-8L
Port 4
RA M
4
P40 to P43
CPU
RO M
The other pins
MOD0, MOD1, VCC, VSS
AVCC, AVR, AVSS
* : Only the MB89120A series has wake-up interrupt inputs and remote control transmission.
Note : Parenthesized pins are available only with the MB89120A series.
DS07-12509-8E
17
MBMB89120/120A Series
■ CPU CORE
1. Memory Space
The microcontrollers of the MB89120/120A series offer 64 Kbytes of memory for storing all of I/O, data, and
program areas. The I/O area is allocated from the lowest address. The data area is allocated immediately above
the I/O area. The data area can be divided into register, stack, and direct areas according to the application.
The program area is allocated from exactly the opposite end of I/O area, that is, near the highest address. The
tables of interrupt reset vectors and vector call instructions are allocated from the highest address with the
program area. The memory space of the MB89120/120A series is structured as illustrated below :
Memory Space
MB89123A
MB89P133A
MB89121
MB89P131
0000 H
0000 H
I/O
007F H
0080 H
0000 H
I/O
007F H
0080 H
Not available
00BF H
00C0 H
0100 H
RAM
Not available
DFFFH
E000 H
EFFFH
F000 H
ROM
RAM
1 KB
00FF H
0100 H
Register
Register
01FF H
0200 H
BFFFH
C000 H
Not available
RAM
512 B
Register
Not available
I/O
007F H
0080 H
00FF H
0100 H
017F H
0180 H
017F H
0180 H
0000 H
007F H
0080 H
RAM
Register
MB89PV130A
I/O
I/O
0100 H
0100 H
MB89P135A
0000 H
007F H
0080 H
RAM
Register
013F H
0140 H
MB89125A
01FF H
0200 H
027F H
0280 H
Vacancy
BFFFH
C000 H
047F H
0480 H
7FFF H
8000 H
External
ROM
32 KB
ROM
16 KB
ROM
Vacancy
ROM
FFFFH
18
FFFFH
FFFFH
FFFFH
FFFFH
DS07-12509-8E
MBMB89120/120A Series
2. Registers
The F2MC-8L family has two types of registers; dedicated hardware registers and general-purpose memory
registers. The following dedicated registers are provided :
Program counter (PC) :
Accumulator (A) :
A 16-bit register for indicating the instruction storage positions
A 16-bi temporary register for arithmetic operations, etc. When the
instruction is an 8-bit data processing instruction, the lower byte is used.
Temporary accumulator (T) : A 16-bit register which is used for arithmetic operations with the accumulator
When the instruction is an 8-bit data processing instruction, the lower byte is
used.
Index register (IX) :
A 16-bit register for index modification
Extra pointer (EP) :
A 16-bit pointer for indicating a memory address
Stack pointer (SP) :
A 16-bit pointer for indicating a stack area
Program status (PS) :
A 16-bit register for storing a register pointer, a condition code
Initial value
16 bits
FFFDH
: Program counter
PC
A
: Accumulator
Indeterminate
T
: Temporary accumulator
Indeterminate
IX
: Index register
Indeterminate
EP
: Extra pointer
Indeterminate
SP
: Stack pointer
Indeterminate
PS
: Program status
I-flag = 0, IL1, IL0 = 11
The other bit values are Indeterminate.
The PS can further be divided into higher 8 bits for use as a register bank pointer (RP) and the lower 8 bits for
use as a condition code register (CCR) (see the diagram below) .
Structure of the Program Status Register
15
PS
14
13
12
10
9
8
Vacancy Vacancy Vacancy
RP
RP
DS07-12509-8E
11
7
6
5
4
3
2
1
0
H
I
IL1, IL0
N
Z
V
C
CCR
19
MBMB89120/120A Series
The RP indicates the address of the register bank currently in use. The relationship between the pointer contents
and the actual address is based on the conversion rule illustrated below.
Rule for Conversion of Actual Addresses of the General-purpose Register Area
RP
Lower OP codes
"0" "0" "0" "0" "0" "0" "0" "1" R4 R3 R2 R1 R0 b2
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
b1
b0
↓
↓
Generated addresses A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data, and
bits for control of CPU operations at the time of an interrupt.
H-flag :
Set to “1” when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation.
Cleared “0” otherwise. This flag is for decimal adjustment instructions.
I-flag : Interrupt is enabled when this flag is set to “1”. Interrupt is disabled when the flag is cleared to “0”.
Cleared to “0” at the reset.
IL1, IL0 : Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level
is higher than the value indicated by this bit.
N-flag :
Z-flag :
V-flag :
C-flag :
20
IL1
IL0
Interrupt level
0
0
0
1
1
0
2
1
1
3
1
High-low
High
Low
Set to “1” if the MSB becomes “1” as the result of an arithmetic operation. Cleared to “0” otherwise.
Set to “1” when an arithmetic operation results in 0. Cleared to “0” otherwise.
Set to “1” if the twos complement overflows as a result of an arithmetic operation. Cleared to “0” if
the overflow does not occur.
Set to “1” when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared to
“0” otherwise. Set to the shift-out value in the case of a shift instruction.
DS07-12509-8E
MBMB89120/120A Series
The following general-purpose registers are provided :
General-purpose registers : 8-bit registers for storing data
The general-purpose registers are of 8 bits and located in the register banks of the memory. One bank contains
8 registers and up to a total of 8 banks can be used on the MB89121/P131, and a total of 16 banks can be used
on the MB89123A/125A/P133A and a total of 32 banks can be used on the MB89P135A/PV130A.
The bank currently in use is indicated by the register bank pointer (RP) .
Register Bank Configuration
This address = 0100H + 8 × (RP)
R0
R1
R2
R3
R4
R5
R6
R7
8 banks (MB89121/P131)
16 banks (MB89123A/125A/133A)
32 banks (MB89P135A/PV130A)
Memory area
DS07-12509-8E
21
MBMB89120/120A Series
■ I/O MAP
Address
Read/Write
Register name
Register description
00H
(R/W)
PDR0
Port 0 data register
01H
(W)
DDR0
Port 0 data direction register
02H
(R/W)
PDR1
Port 1 data register
03H
(W)
DDR1
Port 1 data direction register
04H
(R/W)
PDR2
Port 2 data register
05H
Vacancy
06H
Vacancy
07H
(R/W)
SYCC
System clock control register
08H
(R/W)
STBC
Standby control register
09H
(R/W)
WDTC
Watchdog control register
0AH
(R/W)
TBTC
Time-base timer control register
0BH
(R/W)
WPCR
Watch prescaler control register
0CH
(R/W)
PDR3
Port 3 data register
0DH
(W)
DDR3
Port 3 data direction register
0EH
(R/W)
PDR4
Port 4 data register
0FH
(R/W)
BZCR
Buzzer register
10H
Vacancy
11H
Vacancy
12H
(R/W)
SCGC
Peripheral control clock register
Vacancy
13H
14H
(R/W)
RCR1
Remote control transmission control register 1*
15H
(R/W)
RCR2
Remote control transmission control register 2*
16H
Vacancy
17H
Vacancy
18H
(R/W)
T2CR
Timer 2 control register
19H
(R/W)
T1CR
Timer 1 control register
1AH
(R/W)
T2DR
Timer 2 data register
1BH
(R/W)
T1DR
Timer 1 data register
1CH
(R/W)
SMR1
Serial mode register
1DH
(R/W)
SDR1
Serial data register
1EH
Vacancy
1FH
Vacancy
(Continued)
22
DS07-12509-8E
MBMB89120/120A Series
(Continued)
Address
Read/write
Register name
Register description
20H
Vacancy
21H
Vacancy
22H
Vacancy
23H
(R/W)
EIC1
External interrupt control register 1
24H
(R/W)
EIC2
External interrupt control register 2
25H
Vacancy
26H to 31H
Vacancy
32H
(R/W)
EIE2
External interrupt 2 enable register*
33H
(R/W)
EIF2
External interrupt 2 flag register*
34H to 7BH
Vacancy
7CH
(W)
ILR1
Interrupt level register 1
7DH
(W)
ILR2
Interrupt level register 2
7EH
(W)
ILR3
Interrupt level register 3
7FH
Vacancy
* : Only in the MB89120A series
Note : Do not use vacancies.
DS07-12509-8E
23
MBMB89120/120A Series
■ ELECTRICAL CARACTERISTICS
1. Absolute Maximum Ratings
(AVSS = VSS = 0.0 V)
Parameter
Symbol
Rating
Unit
Remarks
Min.
Max.
VCC
AVCC
AVR
VSS − 0.3
VSS + 7.2
V
Use VCC, AVCC , and AVR
set to the same voltage.
VPP
VSS − 0.6
VSS + 13.0
V
MOD1 pin on the
MB89P131/P133A/P135A
Input voltage
VI
VSS − 0.3
VCC + 0.3
V
Output voltage
VO
VSS − 0.3
VCC + 0.3
V
“L” level maximum output current
IOL
⎯
10
mA
“L” level average output current
IOLAV
⎯
4
mA
“L” level total maximum output current
ΣIOL
⎯
100
mA
ΣIOLAV
⎯
20
mA
IOH
⎯
−10
mA
“H” level average output current
IOHAV
⎯
−2
mA
“H” level total maximum output current
ΣIOH
⎯
−30
mA
“H” level total average output current
ΣIOHAV
⎯
−10
mA
Power consumption
PD
⎯
200
mW
Operating temperature
TA
−40
+85
°C
Tstg
−55
+150
°C
Power supply voltage
Program voltage
“L” level total average output current
“H” level maximum output current
Storage temperature
Avarage value (operating
current × operating rate)
Avarage value (operating
current × operating rate)
Avarage value (operating
current × operating rate)
Avarage value (operating
current × operating rate)
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
24
DS07-12509-8E
MBMB89120/120A Series
2. Recommended Operating Conditions
(AVSS = VSS = 0.0 V)
Parameter
Power supply voltage
Operating temperature
Symbol
VCC
TA
Value
Unit
Remarks
Min.
Max.
2.2
6.0
V
Normal operation assurance range *
Applied to “Single-clock MB89121/123A/125A”
2.2
4.0
V
Normal operation assurance range *
Applied to “Dual-clock MB89121/123A/125A”
2.7
6.0
V
Normal operation assurance range *
Applied to “MB89P131/P133A/P135A/PV130A”
1.5
6.0
V
Retains the RAM state in stop mode
−40
+85
°C
* : These values vary with the operating conditions. See “Operating Voltage vs. Main Clock Operating Frequency.”
WARNING: The recommended operating conditions are required in order to ensure the normal operation of
the semiconductor device. All of the device's electrical characteristics are warranted when the
device is operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges.
Operation outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented
on the data sheet. Users considering application outside the listed conditions are advised to contact
their representatives beforehand.
DS07-12509-8E
25
MBMB89120/120A Series
• Operating Voltage vs. Main Clock Operating Frequency
Dual-clock MB89121/123A/125A
Operating voltage (V)
6
5
4
Operation assurance range
3
2
1
1
2
3
4
Main clock operating frequency (MHz) (Instruction cycle time of 4/FCH)
4.0
Minimum execution time (µs)
2.0
1.0
MB89P131/P133A/P135A/PV130A, and single-clock MB89121/123A/125A
Operating voltage (V)
6
5
Operation assurance range
4
3
2
1
1
2
3
4
Main clock oprating frequency (MHz) (Instruction cycle time of 4/FCH)
4.0
Minimum execution time (µs)
2.0
1.0
Note : The shaded area is assured only for the MB89121/123A/125A (instruction cycle time of 4/FCH) .
26
DS07-12509-8E
MBMB89120/120A Series
3. DC Characteristics
Parameter
Symbol
VIH
“H” level input
voltage
“L” level input
voltage
Open-drain
output pin
applied voltage
“H” level output
voltage
“L” level output
voltage
Input leakage
current
(Hi-Z output
leakage current)
Pull-up resistance
Pin
P00 to P07,
P10 to P17
(AVCC = VCC = +5.0 V, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C)
Value
Condition
Unit Remarks
Min.
Typ.
Max.
⎯
0.7 VCC
⎯
VCC +
0.3
V
VIHS
RST,
P30 to P37,
INT20 to INT27
⎯
0.8 VCC
⎯
VCC +
0.3
V
VIL
P00 to P07,
P10 to P17
⎯
VSS −
0.3
⎯
0.3 VCC
V
VILS
RST,
P30 to P37,
INT20 to INT27
⎯
VSS −
0.3
⎯
0.2 VCC
V
VD
P40 to P43
⎯
VSS −
0.3
⎯
VCC +
0.3
V
VOH
P00 to P07,
P10 to P17,
P20 to P27,
P30 to P37
IOH = −2.0 mA
2.4
⎯
⎯
V
VOL
P00 to P07,
P10 to P17
P20 to P27,
P30 to P37,
P40 to P43
IOL = 1.8 mA
⎯
⎯
0.4
V
VOL2
RST
IOL = 4.0 mA
⎯
⎯
0.6
V
P00 to P07,
P10 to P17,
P20 to P27,
P30 to P37,
P40 to P43,
MOD0, MOD1
0.45 V < VI < VCC
⎯
⎯
±5
µA
P00 to P07,
P10 to P17,
P30 to P37,
P40 to P43,
RST
VI = 0.0 V
25
50
100
kΩ
ILI
RPULL
INT20 to
INT27 are
available
only for the
MB89120A
series.
INT20 to
INT27 are
available
only for the
MB89120A
series.
Without
pull-up
resistor
(Continued)
DS07-12509-8E
27
MBMB89120/120A Series
(Continued)
Parameter
Symbol
Pin
MB89121/
123A/125A
⎯
4
7
mA
⎯
6
10
MB89P131/
mA P133A/
P135A
⎯
2
5
mA
⎯
50
100
µA
⎯
1
3
MB89P131/
mA P133A/
P135A
VCC = 3.0 V
FCL = 32.768 kHz
Sub clock sleep
mode
⎯
25
50
µA
ICCT
VCC = 3.0 V
FCL = 32.768 kHz
• Watch mode
• Main clock stop
mode at dual
clock product
⎯
⎯
15
µA
ICCH
TA = +25 °C
• Sub clock stop
mode
• Main clock stop
mode at single
clock product
⎯
⎯
1
µA
f = 1 MHz
⎯
10
⎯
pF
VCC = 5.0 V
FCH = 4.00 MHz
tinst*2 = 1.0 µs
ICC1
VCC = 5.0 V
FCH = 4.00 MHz
Main sleep mode
tinst*2 = 1.0 µs
ICCS1
VCC = 3.0 V
FCL = 32.768 kHz
Sub clock mode
ICCL
Power supply
current*1
ICCLS
Input capacitance
(AVCC = VCC = +5.0 V, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C)
Value
Condition
Unit Remarks
Min.
Typ.
Max.
CIN
VCC
(External clock
operation)
Other than
AVCC, AVSS,
VCC, and VSS
MB89121/
123A/125A
*1 : The measurement conditions of power supply current is external clock. (VCC = 5.0 V, VCC = 3.0 V)
*2 : For information on tinst, see “ (4) Instruction Cycle” in “4. AC Characteristics.”
28
DS07-12509-8E
MBMB89120/120A Series
4. AC Characteristics
(1) Reset Timing
Parameter
RST “L” pulse width
Symbol
(VCC = +5.0 V ±10%, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C)
Value
Condition
Unit
Remarks
Min.
Max.
⎯
tZLZH
48 tHCYL*
⎯
ns
* : tHCYL is the oscillation cycle (1/FCH) input to the X0.
tZLZH
RST
0.8 VCC
0.2 VCC
0.2 VCC
(2) Power-on Reset
Parameter
Power supply rising time
Symbol
Condition
(AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C)
Value
Unit
Remarks
Min.
Max.
tR
⎯
50
ms
Power-on reset
function only
1
⎯
ms
Due to repeated
operations
⎯
Power supply cut-off time
tOFF
Note : Make sure that power supply rises within the oscillation stabilization time selected.
For example, when the main clock is operating at FCH = 3 MHz and the oscillation stabilization time select
option has been set to 212/FCH, the oscillation stabilization wait time is 1.4 ms and accordingly the maximum
value of power supply rising time is about 1.4 ms.
Keep in mind that rapid changes in power supply voltage may cause a power-on reset. If power supply
voltage needs to be varied in the course of operation, a smooth voltage rise is recommended.
tR
tOFF
2.0 V
VCC
DS07-12509-8E
0.2 V
0.2 V
0.2 V
29
MBMB89120/120A Series
(3) Clock Timings
(VSS = 0.0 V, TA = −40 °C to +85 °C)
Parameter
Symbol
Pin
FCH
Value
Unit
Remarks
Min.
Typ.
Max.
X0, X1
1
⎯
4.2
MHz Main clock
FCL
X0A, X1A
⎯
32.768
⎯
kHz
Sub clock
tHCYL
X0, X1
238
⎯
1000
ns
Main clock
tLCYL
X0A, X1A
⎯
30.5
⎯
µs
Sub clock
Input clock pulse width
PWH1
PWL1
X0
72
⎯
⎯
ns
External clock
Input clock rising/falling time
tCR1
tCF1
X0
⎯
⎯
24
ns
External clock
Clock frequency
Clock cycle time
X0, X1 Timings and Conditions of Applied Voltage
tHCYL
0.8 VCC
X0
0.2 VCC
PWH1
PWL1
tCF1
tCR1
Main Clock Conditions of Applied Voltage
When a crystal
or
ceramic resonator is used
X0
X1
When an external clock is used
X0
X1
FCH
C0
30
C1
Open
FCH
DS07-12509-8E
MBMB89120/120A Series
X0A, X1A Timings and Conditions of Applied Voltage
tLCYL
0.8 VCC
X0A
Sub clock Conditions of Applied Voltage
When a crystal
or
ceramic resonator is used
X0A
X1A
Single-clock option is used
X0A
X1A
Open
Rd
FCL
C0
C1
(4) Instruction Cycles
(VSS = 0.0 V, TA = −40 °C to +85 °C)
Parameter
Instruction cycle
(minimum execution time)
DS07-12509-8E
Symbol
tinst
Value (typical)
4/FCH, 8/FCH, 16/FCH,
64/FCH
2/FCL
Unit
Remarks
µs
(4/FCH) tinst = 1.0 µs when operating at
FCH = 4 MHz
µs
tinst = 61.036 µs when operating at
FCL = 32.768 kHz
31
MBMB89120/120A Series
(5) Serial I/O Timings
(VCC = +5.0 V ±10%, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C)
Symbol
Pin
Serial clock cycle time
tSCYC
SCK
SCK ↓ → SO time
tSLOV
SCK, SO
Valid SI → SCK ↑
tIVSH
SI, SCK
SCK ↑ → Valid SI hold time
tSHIX
SCK, SI
Serial clock “H” pulse width
tSHSL
Serial clock “L” pulse width
tSLSH
Parameter
Condition
Internal clock
operation
SCK
External clock
operation
Value
Unit
Min.
Max.
2 tinst*
⎯
µs
−200
200
ns
200
⎯
ns
200
⎯
ns
tinst*
⎯
µs
tinst*
⎯
µs
0
200
ns
SCK ↓ → SO time
tSLOV
SCK, SO
Valid SI → SCK ↑
tIVSH
SI, SCK
200
⎯
ns
SCK ↑ → Valid SI hold time
tSHIX
SCK, SI
200
⎯
ns
Remarks
* : For information on tinst, see “ (4) Instruction Cycles.”
Internal Shift Clock Mode
tSCYC
SCK
2.4 V
0.8 V
0.8 V
tSLOV
2.4 V
SO
0.8 V
tIVSH
tSHIX
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
SI
External Shift Clock Mode
tSLSH
tSHSL
SCK
0.8 VCC
0.2 VCC
0.8 VCC
0.2 VCC
tSLOV
SO
2.4 V
0.8 V
tIVSH
tSHIX
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
SI
32
DS07-12509-8E
MBMB89120/120A Series
(6) Peripheral Input Timings
Parameter
Symbol
Peripheral input “H” pulse width
tILIH
Peripheral input “L” pulse width
tIHIL
(VCC = +5.0 V ±10%, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C)
Value
Pin
Unit Remarks
Min.
Max.
EC, INT0 to INT2
2 tinst*
⎯
µs
2 tinst*
⎯
µs
* : For information on tinst, see “ (4) Instruction Cycle.”
tIHIL
EC
INT0 to INT2
0.8 VCC
0.2 VCC
DS07-12509-8E
tILIH
0.8 VCC
0.2 VCC
33
MBMB89120/120A Series
■ EXAMPLE CHARACTERISTICS
(1) “L” Level Output Voltage
(2) “H” Level Output Voltage
VCC − VOH vs. IOH
VOL vs. IOL
VOL (V)
VCC − VOH (V)
VCC = 2.5 V
1.1 TA = +25 °C
VCC = 2.2 V
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0
1
2
3 4 5
VCC = 3.0 V
VCC = 4.0 V
VCC = 5.0 V
VCC = 6.0 V
6
7
8
9 10
IOL (mA)
(3) “H” Level Input Voltage/“L” Level Input
Voltage (CMOS Input)
TA = +25 °C
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
1.00
2.00
3.00
4.00
VCC = 3.0 V
VCC = 4.0 V
VCC = 5.0 V
VCC = 6.0 V
−2.0
−2.5
−3.0
IOH (mA)
VIN vs. VCC
4.5
0
.00
VCC = 2.5 V
(4) “H” Level Input Voltage/“L” Level Input
Voltage (Hysteresis Input)
VIN vs. VCC
VIN (V)
5.0
1.1 TA = +25 °C
1.0
VCC = 2.2 V
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
−.5
−1.0 −1.5
0.0
5.00
6.00
7.00
VCC (V)
VIN (V)
5.0
4.5
TA = +25 °C
4.0
VIHS
3.5
3.0
2.5
2.0
VILS
1.5
1.0
0.5
0
.00 1.00 2.00 3.00 4.00 5.00 6.00 7.00
VCC (V)
VIHS : Threshold when input voltage in hysteresis
characteristics is set to “H” level
VILS : Threshold when input voltage in hysteresis
characteristics is set to “L” level
(5) Pull-up Resistance
RPULL vs. VCC
RPULL (kΩ)
1000
TA = +25 °C
300
100
50
10
0
34
1
2
3
4
5
6
7
VCC (V)
DS07-12509-8E
MBMB89120/120A Series
(6) Power Supply Current
ICC1 vs. VCC
ICC (mA)
5.0
4.5
4.0
ICCS1 vs. VCC
Divide by 4
(ICC1)
FCH = 4.0 MHz
TA = +25 °C
ICCS (mA)
3.0
FCH = 4.0 MHz
TA = +25 °C
2.5
3.5
Divide by 4 (ICCS1)
2.0
Divide by 64
3.0
2.5
1.5
2.0
Divide by 64
1.5
1.0
1.0
0.5
0.5
0.0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
VCC (V)
0.0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
VCC (V)
ICCLS vs. VCC
ICCL vs. VCC
ICCL (µA)
200
TA = +25 °C
180
ICCLS (µA)
50
160
40
140
35
120
30
100
25
80
20
60
15
40
10
20
5
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
VCC (V)
TA = +25 °C
45
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
VCC (V)
ICCH vs. VCC
ICCT vs. VCC
ICCT (µA)
30
TA = +25 °C
25
20
ICCH (µA)
2.0
TA = +25 °C
1.8
1.6
1.4
1.2
15
1.0
0.8
10
5
0.6
0.4
0.2
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
VCC (V)
DS07-12509-8E
0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
VCC (V)
35
MBMB89120/120A Series
■ MASK OPTIONS
Part number
No.
Specifying procedure
MB89121
MB89123A
MB89125A
MB89P131
MB89P133A
Specify when ordering
masking
MB89P135A
MB89PV130A
Set with EPROM
programmer
Specification
impossible
1
Pull-up resistors
• P00 to P07, P10 to P17,
• P30 to P37, P40 to P43
Selectable by pin
Selectable by pin (P40 to P43 must be set without a
pull-up resistor.)
All pins fixed to
no pull-up resistor optional
2
Power-on reset
Power-on reset provided
No power-on reset
Selectable
Selectable
Selectable
With power-on
reset
3
Selection of oscillation stabilization wait time
• The oscillation stabilization wait
time initial value is selectable
Selectable
from 4 types given below.
0 : Oscillation stabilization 22/FCH
1 : Oscillation stabilization 212/FCH
2 : Oscillation stabilization 216/FCH
3 : Oscillation stabilization 218/FCH
Selectable
Selectable
Oscillation stabilization
218/FCH
4
Reset pin output
• Reset output provided
• No reset output
Selectable
Selectable
Selectable
With reset output
5
Clock mode selection
• Single-clock mode
• Dual-clock mode
Selectable
Selectable
Selectable
Dual-clock
mode
6
Main clock oscillation circuit type
• External clock input
Selectable
• Oscillation resonator
Not required*1
7
Peripheral control clock
output function*2
• Not used
• Used
Not required*3
Selectable
*1 : Can be used as either crystal or ceramics oscillation.
*2 : “Used” must be selected when P33 (39 pin) is used as SCO for the peripheral control clock output.
*3 : The peripheral control clock function can be used only by software.
36
DS07-12509-8E
MBMB89120/120A Series
■ MB89P131/P133A STANDARD OPTIONS
No.
Product option
MB89P131-101
MB89P133A-201
1
Pull-up resistor
Not provided for any port
Not provided for any port
2
Power-on reset
Provided
Provided
3
Selection of oscillation stabilization
2 : Oscillation stabilization 216/FCH 2 : Oscillation stabilization 216/FCH
time
4
Reset pin output
Provided
Provided
5
Clock mode selection
Dual-clock mode
Dual-clock mode
■ ORDERING INFORMATION
Part number
MB89121PFM
MB89123APFM
MB89125APFM
MB89P131-101PFM
MB89P133A-201PFM
MB89P135A-101PFM
MB89PV130ACF-ES
DS07-12509-8E
Package
Remarks
48-pin Plastic QFP
(FPT-48P-M13)
48-pin Ceramic MQFP
(MQP-48C-P01)
37
MBMB89120/120A Series
■ PACKAGE DIMENSION
48-pin plastic QFP
Lead pitch
0.80 mm
Package width ×
package length
10 × 10 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
2.35 mm MAX
Code
(Reference)
P-QFP44-10×10-0.80
(FPT-48P-M13)
48-pin plastic QFP
(FPT-48P-M13)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
13.10±0.40(.516±.016)SQ
* 10.00±0.20(.394±.008)SQ
36
0.17±0.06
(.007±.002)
25
37
24
Details of "A" part
+0.40
0.10(.004)
1.95 –0.20
+.016
.077 –.008
(Mounting height)
0.25(.010)
INDEX
0~8°
13
48
1
0.80(.031)
C
"A"
12
0.32±0.05
(.013±.002)
0.20(.008)
0.80±0.20
(.031±.008)
0.88±0.15
(.035±.006)
+0.10
0.20 –0.20
+.004
.008 –.008
(Stand off)
M
2003-2008 FUJITSU MICROELECTRONICS LIMITED F48023S-c-3-5
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
Please check the latest package dimensions at the following URL.
http://edevice.fujitsu.com/package/en-search/
38
DS07-12509-8E
MBMB89120/120A Series
■ MAIN CHANGES IN THIS EDITION
Page
Section
Change Results
7
■ PIN DESCRIPTION
Changed the function description of AVCC pin (pin no. 1).
Power supply(GND) pin → Power supply pin
15
■ HANDLING MB89P131/P133A/
P135A
Deleted the item of “3. EPROM Programmer Socket
Adapter”.
16
■ PROGRAMMING TO THE EPROM Deleted the item of “2. Programming Socket Adapter”.
WITH PIGGYBACK/EVALUATION
DEVICE
31
■ ELECTRICAL CARACTERISTICS
4. AC Characteristics
Deleted the item of “(5) Recommended Resonator
Manufacturers”.
37
■ ORDERING INFORMATION
Changed the ordering information.
MB89P131PFM-101 → MB89P131-101PFM
MB89P133APFM-201 → MB89P133A-201PFM
MB89P135APFM
→ MB89P135A-101PFM
The vertical lines marked in the left side of the page show the changes.
DS07-12509-8E
39
MBMB89120/120A Series
FUJITSU MICROELECTRONICS LIMITED
Shinjuku Dai-Ichi Seimei Bldg., 7-1, Nishishinjuku 2-chome,
Shinjuku-ku, Tokyo 163-0722, Japan
Tel: +81-3-5322-3347 Fax: +81-3-5322-3387
http://jp.fujitsu.com/fml/en/
For further information please contact:
North and South America
FUJITSU MICROELECTRONICS AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600 Fax: +1-408-737-5999
http://www.fma.fujitsu.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE. LTD.
151 Lorong Chuan,
#05-08 New Tech Park 556741 Singapore
Tel : +65-6281-0770 Fax : +65-6281-0220
http://www.fmal.fujitsu.com/
Europe
FUJITSU MICROELECTRONICS EUROPE GmbH
Pittlerstrasse 47, 63225 Langen, Germany
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/microelectronics/
FUJITSU MICROELECTRONICS SHANGHAI CO., LTD.
Rm. 3102, Bund Center, No.222 Yan An Road (E),
Shanghai 200002, China
Tel : +86-21-6146-3688 Fax : +86-21-6335-1605
http://cn.fujitsu.com/fmc/
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
206 Kosmo Tower Building, 1002 Daechi-Dong,
Gangnam-Gu, Seoul 135-280, Republic of Korea
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://kr.fujitsu.com/fmk/
FUJITSU MICROELECTRONICS PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel : +852-2377-0226 Fax : +852-2376-3269
http://cn.fujitsu.com/fmc/en/
Specifications are subject to change without notice. For further information please contact each office.
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose
of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS
does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating
the device based on such information, you must assume any responsibility arising out of such use of the information.
FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use
or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS
or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or
other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured
as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to
the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear
facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon
system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising
in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current
levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of
the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited: Sales Promotion Department