FUJITSU SEMICONDUCTOR DATA SHEET DS07-12510-10E 8-bit Proprietary Microcontroller CMOS F2MC-8L MB89130/130A Series MB89131/P131/133A/P133A/135A/ MB89P135A/PV130A ■ DESCRIPTION The MB89130/130A series has been developed as a general-purpose version of the F2MC*-8L family consisting of proprietary 8-bit, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers contain a great variety of peripheral functions such as timers, a serial interface, an A/D converter, and external interrupts. The MB89130A series also include a remote control transmitting output and wake-up interrupt function. * : F2MC stands for FUJITSU Flexible Microcontroller. ■ FEATURES • • • • • • • • • F2MC-8L family CPU core Low-voltage operation (when an A/D converter is not used) Low current consumption (applicable to the dual-clock system) Minimum execution time : 0.95 µs at 4.2 MHz 21-bit timebase timer I/O ports : max. 36 ports External interrupt 1 : 3 channels External interrupt 2 (wake-up function) : 8 channels (only for the MB89130A series) 8-bit serial I/O : 1 channel (Continued) ■ PACKAGE 48-pin plastic QFP 48-pin plastic SH-DIP 48-pin ceramic MQFP (FPT-48P-M13) (DIP-48P-M01) (MQP-48C-P01) MB89130/130A Series (Continued) • 8/16-bit timer/counter : 1 channel • 8-bit A/D converter : 4 channels • Remote control transmitting frequency generator (for the MB89130A series only) • Low-power consumption modes (stop, sleep, and watch mode) • QFP-48 package, SH-DIP-48 package • CMOS technology 2 MB89130/130A Series ■ PRODUCT LINEUP Part number Item MB89131 MB89133A ROM size 4 K × 8 bits (internal mask ROM) RAM size 128 × 8 bits Ports MB89P133A Mass-produced products (mask ROM products) Classification CPU functions MB89135A 8 K × 8 bits (internal mask ROM) One-time PROM products 16 K × 8 bits (internal mask ROM) 4 K × 8 bits 8 K × 8 bits (internal PROM, (internal PROM, to be to be programmed programmed with generalwith generalpurpose EPROM purpose EPROM programmer) programmer) 256 × 8 bits 128 × 8 bits The number of instructions : Instruction bit length : Instruction length : Data bit length : Minimum execution time : Minimum interrupt processing time : 136 8 bits 1 to 3 bytes 1, 8, 16 bits 0.95 µs at 4.2 MHz 8.57 µs at 4.2 MHz Output ports (N-ch open-drain ports) : Output ports (CMOS) : I/O ports (CMOS) : 4 (All also serve as peripherals.) Total : MB89P131 8 24 (8 ports also serve as peripherals. For MB89130A, 16 ports also serve as.) 36 8/16-bit timer/ counter 8-bit timer/counter × 2 channels or a 16-bit event counter 8-bit serial I/O 8 bits LSB/MSB first selectable 8-bit resolution × 4 channels A/D conversion mode (minimum conversion time : 42 µs at 4.2 MHz) Sense mode (minimum conversion time : 11.4 µs at 4.2 MHz) Capable of continuous activation by an internal timer Reference voltage input 8-bit A/D converter 3 independent channels (edge selection, interrupt vector, source flag) Rising/falling both edges selectable External interrupt 1 Used also for wake-up from stop/sleep mode. (Edge detection is also permitted in the stop mode.) External interrupt 2 (wake-up function) 8 channels (only for level detection) Remote control transmitting generator 1 channel (Pulse width and cycle selectable by program) Standby mode Sleep, stop, and clock mode Process Operating voltage* CMOS 2.2 to 4.0 V (with the dual-clock option) 2.2 to 6.0 V (with the single-clock option) 2.7 V to 6.0 V * : Varies with conditions such as the operating frequency. (See “■ ELECTRICAL CHARACTERISTICS”.) (Continued) 3 MB89130/130A Series (Continued) Part number MB89P135 MB89PV130A One-time PROM products Piggyback/evaluation product ROM size 16 K × 8 bits (internal PROM, to be programmed with general-purpose EPROM programmer) 32 K × 8 bits (external ROM) RAM size 512 × 8 bits 1 K × 8 bits Item Classification CPU functions Ports The number of instructions Instruction bit length Instruction length Data bit length Minimum execution time Minimum interrupt processing time : 136 : 8 bits : 1 to 3 bytes : 1, 8, 16 bits : 0.95 µs at 4.2 MHz : 8.57 µs at 4.2 MHz Output ports (N-ch open-drain ports) Output ports (CMOS) I/O ports (CMOS) : 4 (All also serve as peripherals.) :8 : 24 (8 ports also serve as peripherals. For MB89130A, 16 ports also serve as peripherals.) : 36 Total 8/16-bit timer/ counter 8-bit timer/counter × 2 channels or a 16-bit event counter 8-bit serial I/O 8 bits LSB/MSB first selectable 8-bit A/D converter 8-bit resolution × 4 channels A/D conversion mode (minimum conversion time : 42 µs at 4.2 MHz) Sense mode (minimum conversion time : 11.4 µs at 4.2 MHz) Capable of continuous activation by an internal timer Reference voltage input External interrupt 1 3 independent channels (selectable edge, interrupt vector, source flag) Rising/falling both edges selectable Used also for wake-up from the stop/sleep mode. (Edge detection is also permitted in the stop mode.) External interrupt 2 (wake-up function) 8 channels (only for level detection) Remote control transmitting frequency generator 1 channel (Pulse width and cycle selectable by program) Standby mode Sleep, stop, and clock mode Process Operating voltage EPROM for use 4 CMOS 2.7 V to 6.0 V 2.7 V to 6.0 V MBM27C256A-20TVM MB89130/130A Series ■ PACKAGE AND CORRESPONDING PRODUCTS Package MB89131 MB89133A MB89135A MB89P133A MB89P131 FPT-48P-M13 DIP-48P-M01 × MQP-48C-P01 × × MB89P135A MB89PV130A Package × × × × × × FPT-48P-M13 DIP-48P-M01 × MQP-48C-P01 × × : Available, × : Not available ■ DIFFERENCES AMONG PRODUCTS 1. Memory Size Before evaluating using the OTPROM (one-time PROM) products, verify its differences from the product that will actually be used. Take particular care on the following points : • The number of register banks available is different among the MB89131, MB89133A/135A and MB89P135A/ PV130A. • The stack area, etc., is set at the upper limit of the RAM. 2. Current Consumption • When operated at low speed, the product with an OTPROM will consume more current than the product with a mask ROM. However, the same is current consumption in sleep/stop modes. (For more information, see “■ ELECTRICAL CHARACTERISTICS”.) • In the case of the MB89PV130A, added is the current consumed by the EPROM which is connected to the top socket. 3. Mask Options Functions that can be selected as options and how to designate these options vary with product. Before using options, check “■ MASK OPITONS”. Take particular care on the following point : • P40 to P43 must be set to no pull-up resistor when an A/D converter is used. • For MB89P135A, pull-up resistor option cannot be set for P40 to P43. • Each option is fixed on the MB89PV130A. 5 MB89130/130A Series ■ PIN ASSIGNMENTS 1 2 3 4 5 6 7 8 9 10 11 12 36 35 34 33 32 31 30 29 28 27 26 25 P36/INT2 P37/BZ/(RCO) P00/(INT20) P01/(INT21) P02/(INT22) P03/(INT23) P04/(INT24) P05/(INT25) P06/(INT26) P07/(INT27) P10 P11 P24 P23 P22 P21 P20 P17 VSS P16 P15 P14 P13 P12 AVCC RST MOD0 MOD1 X0 X1 VCC X0A X1A P27 P26 P25 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 P40/AN0 P41/AN1 P42/AN2 P43/AN3 AVR AVSS P30/SCK P31/SO P32/SI P33/EC/SCO P34/TO/INT0 P35/INT1 (TOP VIEW) (FPT-48P-M13) Note : Parenthesized function is available only for the MB89130A series. (Continued) 6 MB89130/130A Series (TOP VIEW) VSS P16 P15 P14 P13 P12 P11 P10 P07/(INT27) P06/(INT26) P05/(INT25) P04/(INT24) P03/(INT23) P02/(INT22) P01/(INT21) P00/(INT20) P37/BZ/(RCO) P36/INT2 P35/INT1 P34/TO/INT0 P33/EC/SCO P32/SI P31/SO P30/SCK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 P17 P20 P21 P22 P23 P24 P25 P26 P27 X1A X0A VCC X1 X0 MOD1 MOD0 RST AVCC P40/AN0 P41/AN1 P42/AN2 P43/AN3 AVR AVSS (DIP-48P-M01) Note : Parenthesized function is available only for the MB89130A series. (Continued) 7 MB89130/130A Series (Continued) 70 59 68 57 56 55 54 53 77 78 79 80 49 50 51 52 69 70 71 72 73 74 75 61 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 36 35 34 33 32 31 30 29 28 27 26 25 P36/INT2 P37/BZ/(RCO) P00/INT20 P01/INT21 P02/INT22 P03/INT23 P04/INT24 P05/INT25 P06/INT26 P07/INT27 P10 P11 P24 P23 P22 P21 P20 P17 VSS P16 P15 P14 P13 P12 AVCC RST MOD0 MOD1 X0 X1 VCC X0A X1A P27 P26 P25 68 67 66 65 64 63 62 61 48 47 46 45 44 43 42 41 40 39 38 37 P40/AN0 P41/AN1 P42/AN2 P43/AN3 AVR AVSS P30/SCK P31/SO P32/SI P33/EC/SCO P34/TO/INT0 P35/INT1 (TOP VIEW) (MQP-48C-P01) • Pin assignment on package top Pin no. Pin name Pin no. Pin name Pin no. Pin name Pin no. Pin name 49 VPP 57 N.C. 65 O4 73 OE 50 A12 58 A2 66 O5 74 N.C. 51 A7 59 A1 67 O6 75 A11 52 A6 60 A0 68 O7 76 A9 53 A5 61 O1 69 O8 77 A8 54 A4 62 O2 70 CE 78 A13 55 A3 63 O3 71 A10 79 A14 56 N.C. 64 VSS 72 N.C. 80 VCC N.C. : Internally connected. Do not use. 8 MB89130/130A Series ■ PIN DESCRIPTION Pin no. Pin name SH-DIP*1 QFP*2 35 5 X0 36 6 X1 38 8 X0A 39 9 X1A 33 3 MOD0 34 4 MOD1 32 Circuit type Function A Main clock crystal oscillator pins (max. 4.2 MHz) B Subclock crystal oscillator pins (32.768 kHz) C Operation mode selecting pins Connect directly to VSS. D Reset I/O pin This pin is of N-ch open-drain output type with pull-up resistor, and a hysteresis input type. The internal circuit is initialized by the input of “L”. “L” is output from this pin by an internal reset source as a option. 2 RST 16 to 9 34 to 27 P00 (INT20) to P07 (INT27) I General-purpose I/O ports On the MB89130A series, these ports also serve as an external interrupt input. External interrupt inputs are of hysteresis input type. 8 to 2, 48 26 to 20, 18 P10 to P17 E General-purpose I/O ports 47 to 40 17 to 10 P20 to P27 G General-purpose output ports 24 42 P30/SCK F General-purpose I/O port Also serves as the clock I/O for the 8-bit serial I/O. This port is of hysteresis input type. 23 41 P31/SO F General-purpose I/O port Also serves as a 8-bit serial I/O data output. This port is of hysteresis input type. 22 40 P32/SI F General-purpose I/O port Also serves as a 8-bit serial I/O data input. This port is of hysteresis input type. F General-purpose I/O port Also serves as the external clock input for the 8-bit timer/counter. This port is of hysteresis input type. The system clock output is provided as an option. 21 39 P33/EC/SCO 20 38 P34/TO/INT0 F General-purpose I/O port Also serve as the overflow output for the 8-bit timer/ counter and an external interrupt input. This port is of hysteresis input type. 19, 18 37, 36 P35/INT1, P36/INT2 F General-purpose I/O ports Also serves as an external interrupt input. These ports are of hysteresis input type. *1 : DIP-48P-M01 *2 : FPT-48P-M13 (Continued) 9 MB89130/130A Series (Continued) Pin no. SH-DIP*1 QFP*2 Circuit type Function 17 35 P37/BZ/ (RCO) F General-purpose I/O port Also serves as a buzzer output. This port is of hysteresis input type. On the MB89130A series, this port also serves as a remote control output. 30 to 27 48 to 45 P40/AN0 to P43/AN3 H N-ch open-drain output ports Also serve as an analog input for the A/D converter. 37 7 VCC Power supply pin 1 19 VSS Power supply (GND) pin 31 1 AVCC A/D converter power supply pin Use this pin at the same voltage as VCC. 26 44 AVR A/D converter reference voltage input pin 25 43 AVSS A/D converter power supply pin Use this pin at the same voltage as VSS. *1 : DIP-48P-M01 *2 : FPT-48P-M13 10 Pin name MB89130/130A Series • External EPROM pins (MB89PV130A only) Pin no. Pin name I/O Function 49 VPP O “H” level output pin 50 51 52 53 54 55 58 59 60 A12 A7 A6 A5 A4 A3 A2 A1 A0 O Address output pins 61 62 63 O1 O2 O3 I Data input pins 64 VSS O Power supply (GND) pin 65 66 67 68 69 O4 O5 O6 O7 O8 I Data input pins 70 CE O ROM chip enable pin Outputs “H” during standby. 71 A10 O Address output pin 73 OE O ROM output enable pin Outputs “L” at all times. 75 76 77 78 79 A11 A9 A8 A13 A14 O Address output pins 80 VCC O EPROM power supply pin 56 57 72 74 N.C. Internally connected pins Be sure to leave them open. 11 MB89130/130A Series ■ I/O CIRCUIT TYPE Type Circuit Remarks • Crystal or ceramic oscillation type (main clock) Circuit for the MB89P133A/P131/P135A/PV130A External clock input selecting versions of MB89131/ 133A/135A Oscillation feedback resistor of approximately 1 MΩ/5 V X1 X0 Standby control signal A • Crystal or ceramic oscillation type (main clock) Crystal or ceramic oscillation selecting versions of MB89131/133A/135A Oscillation feedback resistor of approximately 1 MΩ/5 V X1 X0 Standby control signal • Crystal and ceramic oscillation type (subclock) Circuit for the MB89131/133A/135A Oscillation feedback resistor of approximately 4.5 MΩ/5 V X1A X0A Standby control signal B • Crystal and ceramic oscillation type (subclock) Circuit for the MB89P131/P133A/P135A/PV130A Oscillation feedback resistor of approximately 4.5 MΩ/5 V X1A X0A Standby control signal C • Output pull-up resistor (P-ch) of approximately 50 kΩ/5 V • Hysteresis input R P-ch D N-ch (Continued) 12 MB89130/130A Series (Continued) Type Circuit Remarks • CMOS output • CMOS input R P-ch E N-ch • Pull-up resistor optional • CMOS output • Hysteresis input R P-ch F N-ch • Pull-up resistor optional • CMOS output P-ch G N-ch R • N-ch open-drain output • Analog input P-ch H N-ch Analog input • CMOS output • CMOS input • The interrupt input is a hysteresis input (available only for the MB89130A series) . P-ch P-ch I • Pull-up resistor optional N-ch Interrupt input Only for MB89130A series • Pull-up resistor optional 13 MB89130/130A Series ■ HANDLING DEVICES 1. Preventing Latchup Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins other than medium- and high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum Ratings” in “■ Electrical Characteristics” is applied between VCC and VSS. When latchup occurs, power supply current increases rapidly and might thermally damage elements. When using, take great care not to exceed the absolute maximum ratings. Also, take care to prevent the analog power supply (AVCC and AVR) and analog input from exceeding the digital power supply (VCC) when the analog system power supply is turned on and off. 2. Treatment of Unused Input Pins Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down resistor. 3. Treatment of Power Supply Pins on Microcontrollers with A/D Converter Connect to be AVCC = VCC and AVSS = AVR = VSS even if the A/D converter are not in use. 4. Treatment of N.C. Pins Be sure to leave (internally connected) N.C. pins open. 5. Power Supply Voltage Fluctuations Although operation is assured within the rated range of VCC power supply voltage, a rapid fluctuation of the voltage could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60 Hz) and the transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched. 6. Precautions when Using an External Clock When an external clock is used, oscillation stabilization time is required even for power-on reset (optional) and wake-up from stop mode. 7. Turning on the supply voltage (only for the MB89P135A) Power on sharply up to the option enabling voltage (2 V) within 13 clock cycles after starting of oscillation. 14 MB89130/130A Series ■ PROGRAMMING TO THE EPROM ON THE MB89P131 The MB89P131 is an OTPROM version of the MB89131. 1. Features • 4-Kbyte PROM on chip • Equivalency to the MBM27C256A in EPROM mode (when programmed with the EPROM programmer) 2. Memory Space Memory space in EPROM mode is diagrammed below. Address 0000H Single chip EPROM mode (Corresponding addresses on the EPROM programmer) I/O 0080H 00C0H Not available RAM 0140H 0000H Not available F000H Not available 7000H PROM 4 KB FFFFH EPROM 4 KB 7FFFH 3. Programming to the EPROM In EPROM mode, the MB89P131 functions equivalent to the MBM27C256A. This allows the PROM to be programmed with a general-purpose EPROM programmer (the electronic signature mode cannot be used) by using the dedicated socket adapter. • Programming procedure (1) Set the EPROM programmer for the MBM27C256A. (2) Load program data into the EPROM programmer at 7000H to 7FFFH (note that addresses F000H to FFFFH while operating as a single chip correspond to 7000H to 7FFFH in EPROM mode) . (3) Program with the EPROM programmer. 15 MB89130/130A Series ■ PROGRAMMING TO THE EPROM ON THE MB89P133A The MB89P133A is an OTPROM version of the MP89133A. 1. Features • 8-Kbyte PROM on chip • Equivalency to the MBM27C256A in EPROM mode (when programmed with the EPROM programmer) 2. Memory Space Memory space in EPROM mode is diagrammed below. Address Single chip 0000H EPROM mode (Corresponding addresses on the EPROM programmer) I/O 0080H RAM 0180H Not available 0000H Not available E000H 6000H PROM 8 KB FFFFH EPROM 8 KB 7FFFH 3. Programming to the EPROM In EPROM mode, the MB89P133A functions equivalent to the MBM27C256A. This allows the PROM to be programmed with a general-purpose EPROM programmer (the electronic signature mode cannot be used) by using the dedicated socket adapter. • Programming procedure (1) Set the EPROM programmer for the MBM27C256A. (2) Load program data into the EPROM programmer at 6000H to 7FFFH (note that addresses E000H to FFFFH while operating as a single chip correspond to 6000H to 7FFFH in EPROM mode) . (3) Program with the EPROM programmer. 16 MB89130/130A Series ■ PROGRAMMING TO THE EPROM ON THE MB89P135A The MB89P135A is an OTPROM version of the MB89133A/135A. 1. Features • 16-Kbyte PROM on chip • Equivalency to the MBM27C256A in EPROM mode (when programmed with the EPROM programmer) 2. Memory Space Memory space in EPROM mode is diagrammed below. Address Single chip 0000H EPROM mode (Corresponding addresses on the EPROM programmer) I/O 0080H RAM 0280H Not available 8000H 0000H Vacancy (Read value FFH) Not available BFF0H 3FF0H Option area Not available BFF6H 3FF6H Vacancy (Read value FFH) Not available C000H 4000H PROM 16 KB FFFFH EPROM 16 KB 7FFFH 3. Programming to the EPROM In EPROM mode, the MB89P135A functions equivalent to the MBM27C256A. This allows the PROM to be programmed with a general-purpose EPROM programmer (the electronic signature mode cannot be used) by using the dedicated socket adapter. • Programming procedure (1) Set the EPROM programmer for the MBM27C256A. (2) Load program data into the EPROM programmer at 4000H to 7FFFH (note that addresses C000H to FFFFH while operating as a single chip correspond to 4000H to 7FFFH in EPROM mode) . (3) Load option data into the EPROM programmer at 3FF0H to 3FF6H. (4) Program with the EPROM programmer. 17 MB89130/130A Series 4. Setting OTPROM Options (MB89P135A Only) The programming procedure is the same as that for the PROM. Options can be set by programming values at the addresses shown on the memory map. The relationship between bits and options is shown on the following bit map : • OTPROM option bit map AdBit 7 Bit 6 dress Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Clock mode selection 1 : Single clock 0 : Dual clock Reset pin output 1 : Yes 0 : No Power-on reset 1 : Yes 0 : No 00 : 22/FCH 10 : 216/FCH 01 : 212/FCH 11 : 218/FCH P05 Pull-up 1 : Yes 0 : No P04 Pull-up 1 : Yes 0 : No P03 Pull-up 1 : Yes 0 : No P02 Pull-up 1 : Yes 0 : No P01 Pull-up 1 : Yes 0 : No P00 Pull-up 1 : Yes 0 : No P16 Pull-up 1 : No 0 : Yes P15 Pull-up 1 : Yes 0 : No P14 Pull-up 1 : Yes 0 : No P13 Pull-up 1 : Yes 0 : No P12 Pull-up 1 : Yes 0 : No P11 Pull-up 1 : Yes 0 : No P10 Pull-up 1 : Yes 0 : No P37 Pull-up 1 : Yes 0 : No P36 Pull-up 1 : Yes 0 : No P35 Pull-up 1 : Yes 0 : No P34 Pull-up 1 : Yes 0 : No P33 Pull-up 1 : Yes 0 : No P32 Pull-up 1 : Yes 0 : No P31 Pull-up 1 : Yes 0 : No P30 Pull-up 1 : Yes 0 : No Vacancy Vacancy Vacancy Vacancy Vacancy Vacancy Vacancy Vacancy Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Vacancy Vacancy Vacancy Vacancy Vacancy Vacancy Vacancy Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Vacancy Vacancy Vacancy Vacancy Vacancy Vacancy Vacancy Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Readable and writable Vacancy Vacancy Vacancy Readable and writable Readable and writable 3FF1H P07 Pull-up 1 : Yes 0 : No P06 Pul-up 1 : Yes 0 : No 3FF2H P17 Pull-up 1 : No 0 : Yes 3FF3H 3FF0H Readable and writable 3FF4H Readable and writable Vacancy 3FF5H Readable and writable Vacancy 3FF6H Readable and writable Oscillation stabilization time Note : Each bit is set to ‘1’ as the initialized value, therefore the pull-up option is selected. 18 Bit 0 MB89130/130A Series ■ HANDLING THE MB89P131/P133A/P135A 1. Recommended Screening Conditions High-temperature aging is recommended as the pre-assembly screening procedure. Program, verify Aging +150 °C, 48 h Data verification Assembly 2. Programming Yield Due to its nature, bit programming test can’t be conducted as Fujitsu delivery test. For this reason, a programming yield of 100% cannot be assured at all times. 3. EPROM Programmer Socket Adapter Part no. MB89P131PF MB89P133APFM MB89P133AP Package Compatible socket adapter Sun Hayato Co., Ltd. QFP-48 ROM-48QF2-28DP-8L SH-DIP-48 ROM-48SD-28DP-8L2 Inquiry : Sun Hayato Co., Ltd. : TEL (81) -3-3986-0403 FAX (81) -3-5396-9106 19 MB89130/130A Series ■ PROGRAMMING TO THE EPROM WITH PIGGYBACK/EVALUATION DEVICE 1. EPROM for Use MBM27C256A-20TVM 2. Programming Socket Adapter To program to the PROM using an EPROM programmer, use the socket adapter (manufacturer : Sun Hayato Co., Ltd.) listed below : Package Socket adapter part number LCC-32 (Square) ROM-32LC-28DP-S Inquiry : Sun Hayato Co., Ltd. : TEL (81) -3-3986-0403 FAX (81) -3-5396-9106 3. Memory Space Memory space in each mode, such as 32-Kbyte PROM is diagrammed below. Address Single chip Corresponding addresses on the EPROM programmer 0000 H I/O 0080 H RAM 0480 H Not available 8000 H 0000 H PROM 32 KB FFFFH EPROM 32 KB 7FFFH 4. Programming to the EPROM (1) (2) (3) 20 Set the EPROM programmer for the MBM27C256A. Load program data into the EPROM programmer at 0000H to 7FFFH. Program with the EPROM programmer. MB89130/130A Series ■ BLOCK DIAGRAM X0A X1A Main clock oscillator Timebase timer Clock controller Reset circuit (WDT) Subclock oscillator (32.768 kHz) 8 RST 8-bit timer/counter P34/TO/INT0 8-bit timer/counter P33/EC/SCO CMOS I/O port Ports 0 and 1 8 P00/ (INT20) to P07/ (INT27) Internal bus X0 X1 External interrupt 2* (wake-up function) P30/SCK P32/SI P31/SO 8-bit serial I/O Port 3 P10 to P17 P35/INT1 8 P20 to P27 Port 2 External interrupt 1 P36/INT2 Remote control* transmitting frequency generator CMOS output port Buzzer output P37/BZ/(RCO) CMOS I/O port F2MC-8L CPU N-ch open-drain output port 8-bit A/D converter 4 Port 4 RAM 4 P40/AN0 to P43/AN3 AVR ROM AVCC AVSS The other pins MOD0, MOD1, VCC, VSS * : Only for the MB89130A series. Note : Parenthesized pin function is only for the MB89130A series. 21 MB89130/130A Series ■ CPU CORE 1. Memory Space The microcontrollers of the MB89130/130A series offer a memory space of 64 Kbytes for storing all of I/O, data, and program areas. The I/O area is allocated from the lowest address. The data area is allocated immediately above the I/O area. The data area can be divided into register, stack, and direct areas according to the application. The program area is allocated from exactly the opposite end, that is, near the highest address. The tables of interrupt reset vectors and vector call instructions are allocated from the highest address within the program area. The memory space of the MB89130/130A series is structured as illustrated below. • Memory Space MB89P133A MB89133A MB89P131 MB89131 0000 H 0000 H 007F H 00C0 H Vacancy 0000 H I/O I/O I/O 0000 H I/O I/O 007F H 007F H 007F H 0080 H 0080 H 0080 H 0080 H RAM 256 B 00FF H 0100 H Register 013F H 0140 H 0000 H MB89PV130A 007F H RAM 128 B 0100 H MB89P135A MB89135A RAM 256 B 00FF H 0100 H Register 017F H 0180 H RAM 512 B 00FF H 0100 H Register 017F H 0180 H RAM 1 KB 00FF H 0100 H Register 01FF H 0200 H Register 01FF H 0200 H 027F H 0280 H Vacancy Vacancy Vacancy Vacancy 047F H 0480 H Vacancy BFFF H C000 H EFFF H F0 00 H FFFF H 22 DFFF H E000 H ROM 4 KB FFFF H BFFF H C000 H FFFF H External ROM 32 KB ROM 16 KB ROM 16 KB ROM 8 KB 7FFF H 8000 H FFFF H FFFF H MB89130/130A Series 2. Registers The F2MC-8L family has two types of registers; dedicated hardware registers in the CPU and general-purpose memory registers. The following registers are provided : Program counter (PC) : A 16-bit register for indicating the instruction storage positions. Accumulator (A) : A 16-bit temporary register for storing arithmetic operations, etc. When the instruction is an 8-bit data processing instruction, the lower byte is used. Temporary accumulator (T) : A 16-bit register which is used for arithmetic operations with the accumulator When the instruction is an 8-bit data processing instruction, the lower byte is used. Index register (IX) : A 16-bit register for index modification Extra pointer (EP) : A 16-bit pointer for indicating a memory address Stack pointer (SP) : A 16-bit pointer for indicating a stack area Program status (PS) : A 16-bit register for storing a register pointer, a condition code 16 bits Initial value FFFDH : Program counter PC A : Accumulator Indeterminate T : Temporary accumulator Indeterminate IX : Index register Indeterminate EP : Extra pointer Indeterminate SP : Stack pointer Indeterminate PS : Program status I-flag = 0, IL1, 0 = 11 The other bit values are Indeterminate. The PS can further be divided into higher 8 bits for use as a register bank pointer (RP) and the lower 8 bits for use as a condition code register (CCR) . (See the diagram below.) • Structure of the Program Status Register 15 PS 14 13 12 RP 11 10 9 8 Vacancy Vacancy Vacancy RP 7 6 H I 5 4 IL1, 0 3 2 1 0 N Z V C CCR 23 MB89130/130A Series The RP indicates the address of the register bank currently in use. The relationship between the pointer contents and the actual address is based on the conversion rule illustrated below. • Rule for Conversion of Actual Addresses of the General-purpose Register Area Lower OP codes RP “0” “0” “0” “0” “0” “0” “0” “1” R4 R3 R2 R1 R0 b2 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ b1 b0 ↓ ↓ Generated addresses A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 The CCR consists of bits indicating the results of arithmetic operations and the contents of transfer data, and bits for control of CPU operations at the time of an interrupt. H-flag : I-flag : IL1, 0 : N-flag : Z-flag : V-flag : C-flag : 24 Set to ‘1’ when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation. Cleared to ‘0’ otherwise. This flag is for decimal adjustment instructions. Interrupt is enabled when this flag is set to ‘1’. Interrupt is disabled when the flag is cleared to ‘0’. Cleared to ‘0’ at the reset. Indicates the level of the interrupt currently allowed. Processes an interrupt only if its request level is higher than the value indicated by this bit. IL1 IL0 Interrupt level 0 0 0 1 1 0 2 1 1 3 1 High-low High Low Set to ‘1’ if the MSB becomes ‘1’ as the result of an arithmetic operation. Cleared to ‘0’ otherwise. Set to ‘1’ when an arithmetic operation results in ‘0’. Cleared to ‘0’ otherwise. Set to ‘1’ if the complement on ‘2’ overflows as a result of an arithmetic operation. Cleared to ‘0’ if the overflow does not occur. Set to ‘1’ when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared to ‘0’ otherwise. Set to the shift-out value in the case of a shift instruction. MB89130/130A Series The following general-purpose registers are provided : General-purpose registers : An 8-bit resister for storing data The general-purpose registers are of 8 bits and located in the register banks of the memory. One bank contains eight registers. Up to a total of 8 banks can be used on the MB89131/P131 and a total of 16 banks can be used on the MB89133A/P133A/135A and a total of 32 banks can be used on the MB89P135A/PV130A. The bank currently in use is indicated by the register bank pointer (RP) . • Register Bank Configuration This address = 0100H + 8 × (RP) R0 R1 R2 R3 R4 R5 R6 R7 8 banks (MB89131/P131) 16 banks (MB89133A/P133A/135A) 32 banks (MB89P135A/PV130A) Memory area 25 MB89130/130A Series ■ I/O MAP Address Read/write Register name Register description 00H (R/W) PDR0 Port 0 data register 01H (W) DDR0 Port 0 data direction register 02H (R/W) PDR1 Port 1 data register 03H (W) DDR1 Port 1 data direction register 04H (R/W) PDR2 Port 2 data register 05H Vacancy 06H Vacancy 07H (R/W) SYCC System clock control register 08H (R/W) STBC Standby control register 09H (R/W) WDTC Watchdog timer control register 0AH (R/W) TBTC Timebase timer control register 0BH (R/W) WPCR Watch prescaler control register 0CH (R/W) PDR3 Port 3 data register 0DH (W) DDR3 Port 3 data direction register 0EH (R/W) PDR4 Port 4 data register 0FH (R/W) BZCR Buzzer register 10H Vacancy 11H Vacancy 12H (R/W) SCGC 13H Peripheral control clock register Vacancy 14H (R/W) RCR1 Remote control transmitting control register 1* 15H (R/W) RCR2 Remote control transmitting control register 2* 16H Vacancy 17H Vacancy 18H (R/W) T2CR Timer 2 control register 19H (R/W) T1CR Timer 1 control register 1AH (R/W) T2DR Timer 2 data register 1BH (R/W) T1DR Timer 1 data register 1CH (R/W) SMR Serial mode register 1DH (R/W) SDR Serial data register 1EH Vacancy 1FH Vacancy (Continued) 26 MB89130/130A Series (Continued) Address Read/write Register name Register description 20H (R/W) ADC1 A/D converter control register 1 21H (R/W) ADC2 A/D converter control register 2 22H (R/W) ADCD A/D converter data register 23H (R/W) EIC1 External interrupt 1 control register 1 24H (R/W) EIC2 External interrupt 1 control register 2 25H Vacancy 26H to 31H Vacancy 32H (R/W) EIE2 External interrupt 2 enable register* 33H (R/W) EIF2 External interrupt 2 flag register* 34H to 7BH Vacancy 7CH (W) ILR1 Interrupt level setting register 1 7DH (W) ILR2 Interrupt level setting register 2 7EH (W) ILR3 Interrupt level setting register 3 7FH Vacancy * : Only for the MB89130A series Note : Do not use vacancies. 27 MB89130/130A Series ■ ELECTRICAL CHARACTERISTICS 1. Absolute Maximum Ratings (AVSS = VSS = 0.0 V) Parameter Power supply voltage Program voltage Symbol Value Unit Max. VCC AVCC VSS − 0.3 VSS + 7.2 V * AVR VSS − 0.3 VSS + 7.2 V AVR must not exceed VCC + 0.3 V VPP VSS − 0.6 VSS + 13.0 V Only for the MB89P131/P133A/ P135A Input voltage VI VSS − 0.3 VCC + 0.3 V Output voltage VO VSS − 0.3 VCC + 0.3 V “L” level maximum output current IOL 10 mA “L” level average output current IOLAV 4 mA “L” level total maximum output current ΣIOL 100 mA “L” level total average output current ΣIOLAV 20 mA “H” level maximum output current IOH –10 mA “H” level average output current IOHAV –2 mA “H” level total maximum output current ΣIOH –30 mA ΣIOHAV –10 mA Power consumption PD 200 mW Operating temperature TA −40 +85 °C Tstg −55 +150 °C “H” level total average output current Storage temperature Remarks Min. Average value (operating current × operating rate) Average value (operating current × operating rate) Average value (operating current × operating rate) Average value (operating current × operating rate) * : Use AVCC and VCC set to the same voltage. Take care so that AVCC does not exceed VCC, such as when power is turned on. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. 28 MB89130/130A Series 2. Recommended Operating Conditions (AVSS = VSS = 0.0 V) Parameter Power supply voltage Operating temperature Symbol Value Unit Remarks Min. Max. 2.2* 6.0* V Normal operation assurance range* MB89131/133A/135A 2.7* 6.0* V Normal operation assurance range* MB89P131/P133A/135A/PV130A 1.5 6.0 V Retains the RAM state in the stop mode AVR 2.0 AVCC V TA −40 +85 °C VCC AVCC * : These values vary with the operating frequencies and the analog assurance range. See Figure 1 and 2, and “5. A/D Converter Electrical Characteristics.” Figure 1 Operating Voltage vs. Main Clock Operating Frequency (MB89P131/P133A/P135A/PV130A, and single-clock MB89131/133/133A/135/135A) Operating voltage (V) 6 5 Operation assurance range 4 3 2 1 1 2 3 4 Main clock oprating frequency (at an instruction cycle of 4/FCH) (MHz) 4.0 2.0 1.0 Minimum execution time (Instruction cycle) (µs) Note : The shaded area is assured only for the MB89131/133/133A/135/135A. 29 MB89130/130A Series Figure 2 Operating Voltage vs. Main Clock Operating Frequency (Dual-clock MB89131/133/133A/135/135A) Operating voltage (V) 6 5 4 Operation assurance range 3 2 1 1 2 3 4 Main clock oprating frequency (at an instruction cycle of 4/FCH) (MHz) 4.0 2.0 1.0 Minimum execution time (Instruction cycle) (µs) Figure 1 and 2 indicate the operating frequency of the external oscillator at an instruction cycle of 4/FCH. Since the operating voltage range is dependent on the instruction cycle, see minimum execution time if the operating speed is switched using a gear. WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device’s electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 30 MB89130/130A Series 3. DC Characteristics Parameter “H” level input voltage “L” level input voltage Open-drain output pin applied voltage “H” level output voltage “L” level output voltage Input leakage current (Hi-z output leakage current) Pull-up resistance (AVCC = VCC = +5.0 V, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C) Symbol Pin Condition Value Min. Typ. Max. 0.7 VCC VCC + 0.3 Unit VIH P00 to P07, P10 to P17 VIHS RST, P30 to P37, INT20 to INT27 0.8 VCC VCC + 3.0 V VIL P00 to P07, P10 to P17 VSS − 0.3 0.3 VCC V VILS RST, P30 to P37 INT20 to INT27 VSS − 0.3 0.2 VCC V VD P40 to P43 VCC − 0.3 VCC + 0.3 V VOH P00 to P07, P10 to P17, P20 to P27, P30 to P37 IOH = −2.0 mA 2.4 V VOL P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P43 IOL = 1.8 mA 0.4 V VOL2 RST IOL = 4.0 mA 0.6 V P00 to P07, P10 to P17, P20 to P27, 0.0 V < VI < VCC P30 to P37, P40 to P43, MOD0, MOD1 ±5 µA P00 to P07, P10 to P17, P30 to P37, P40 to P43, RST 25 50 100 kΩ ILI1 RPULL VI = 0.0 V Remarks V INT20 to INT27 are available only for the MB89130A series. INT20 to INT27 are available only for the MB89130A series. Without pull-up resistor (Continued) 31 MB89130/130A Series (Continued) Parameter (AVCC = VCC = +5.0 V, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C) Symbol Pin Value Remarks Typ. Max. 4 7 mA MB89131/ 133A/135A 6 10 mA MB89P131/ P133A/P135A 2 5 mA 50 100 µA MB89131/ 133A/135A 1 3 mA MB89P131/ P133A/P135A FCL = 32.768 kHz VCC = 3.0 V Subclock sleep mode 25 50 µA ICCT FCL = 32.768 kHz VCC = 3.0 V • Watch mode • Main clock stop mode in dualclock system 15 µA ICCH TA = +25 °C • Subclock stop mode • Main clock stop mode in singleclock system 1 µA IA AVCC FCH = 4 MHz, when A/D conversion is operating 1 3 mA IAH AVCC FCH = 4 MHz, TA = +25 °C, when A/D conversion is not operating 1 µA CIN Other than AVCC, AVSS, VCC, and VSS f = 1 MHz 10 pF FCH = 4.00 MHz VCC = 5.0 V tinst*2 = 1.0 µs ICCS1 FCH = 4.00 MHz VCC = 5.0 V tinst*2 = 1.0 µs Main clock sleep mode ICCL FCL = 32.768 kHz VCC = 3.0 V Subclock mode ICCLS VCC (External clock operation) Power supply current*1 *1 : The power supply current is measured at the external clock. *2 : For information on tinst, see “ (4) Instruction Cycle” in “4. AC Characteristics.” 32 Unit Min. ICC1 Input capacitance Condition MB89130/130A Series 4. AC Characteristics (1) Reset Timing (VCC = +5.0 V ± 10%, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C) Parameter Symbol Condition tZLZH RST “L” pulse width Value Min. Max. 48 tHCYL* Unit Remarks ns * : tHCYL is the oscillation cycle (1/FCH) to input to the X0 pin. tZLZH 0.8 VCC RST 0.2 VCC 0.2 VCC (2) Power-on Reset Parameter (AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C) Symbol Power supply rising time tR Power supply cut-off time tOFF Condition Value Unit Remarks Min. Max. 50 ms Power-on reset function only 1 ms Due to repeated operations Note : Make sure that power supply rises within the oscillation stabilization time selected. For example, when the main clock is operating at 3 MHz (FCH) and the oscillation stabilization time selecting option has been set to 212/FCH, the oscillation stabilization time is 1.4 ms. Therefore, the maximum value of power supply rising time is about 1.4 ms. Rapid changes in power supply voltage may cause a power-on reset. If power supply voltage needs to be varied in the course of operation, a smooth voltage rise is recommended. tOFF tR 2.0 V VCC 0.2 V 0.2 V 0.2 V 33 MB89130/130A Series (3) Clock Timing (VSS = 0.0 V, TA = −40 °C to +85 °C) Parameter Symbol Pin FCH Value Unit Remarks Min. Typ. Max. X0, X1 1 4.2 MHz Main clock FCL X0A, X1A 32.768 kHz tHCYL X0, X1 238 1000 ns Main clock tLCYL X0A, X1A 30.5 µs Subclock Input clock pulse width PWH1 PWL1 X0 30 ns External clock Input clock rising/falling time tCR1 tCF1 X0 24 ns External clock Input clock frequency Clock cycle time Subclock • X0 and X1 Timing and Conditions of Applied Voltage tHCYL PWH1 PWL1 tCF1 X0 0.8 VCC 0.8 VCC 0.2 VCC tCR1 0.8 VCC 0.2 VCC • Main Clock Conditions When a crystal or ceramic resonator is used X0 X1 When an external clock is used X0 X1 FCH C0 34 C1 Open FCH MB89130/130A Series • X0A and X1A Timing and Conditions of Applied Voltage tLCYL 0.8 VCC 0.8 VCC X0A • Subclock Conditions When a crystal or ceramic resonator is used X0A When a single-clock option is used X1A X0A X1A Open Rd FCL C0 C1 (4) Instruction Cycle Parameter Instruction cycle (minimum execution time) Symbol Value Unit Remarks 4/FCH, 8/FCH, 16/FCH, 64/FCH µs (4/FCH) tinst = 1.0 µs when operating at FCH = 4 MHz 2/FCL µs tinst = 61.036 µs when operating at FCL = 32.768 kHz tinst 35 MB89130/130A Series (5) Recommended Resonator Manufacturers • Sample Application of Piezoelectric Resonator (FAR Family) for Main Clock Oscillation Circuit X0 X1 R ∗1 C1∗ C2 ∗ 2 2 Frequency Dumping FAR part number*1 (MHz) resistor (built-in capacitor type) Temperature Loading characteristics of FAR frequency capacitors*2 (TA = −20 °C to +60 °C) 1000 Ω ±0.5% ±0.5% 510 Ω ±0.5% ±0.5% ±0.5% ±0.5% 1 kΩ ±0.5% ±0.5% 750 Ω ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% FAR-C4 B-04194- 00 4.194 Inquiry : FUJITSU MEDIA DEVICES LIMITED ±0.5% ±0.5% FAR-C4CC-02000-L00 2.00 FAR-C4 C-02000- 20 FAR-C4 A-03000- 20 3.00 FAR-C4 A-04000- 01 FAR-C4 A-04000- 21 FAR-C4CB-04000-M00 FAR-C4 B-04000- 00 36 Initial deviation of FAR frequency (TA = +25 °C) 4.00 Built-in MB89130/130A Series • Sample Application of Ceramic Resonator for Main Clock Oscillation Circuit X0 X1 R ∗ C1 • Mask ROM products Resonator manufacturer* Kyocera Corporation C2 Resonator KBR-4.0MKS Frequency (MHz) C1 (pF) C2 (pF) R 4.00 33 33 Not required Matsushita Electronic EFOV4004B Components Co,. Ltd. 4.00 CSBF1000J 1.00 100 6.8 kΩ 30 30 Not required CST4.00MGW Built-in Built-in Not required CSA4.00MGU 30 30 Not required Built-in Built-in Not required 100 100 Not required CST4.00MGWU040 Built-in Built-in Not required CSTCS4.00MG Built-in Built-in Not required CSTCS4.00MGWOC5 Built-in Built-in Not required Built-in Built-in Not required CST4.00MGWU CSA4.00MGU040 TDK Corporation 1.5 kΩ 100 CSA4.00MG Murata Mfg. Co., Ltd. 33 (Built-in) 33 (Built-in) CCR4.0MC3 4.00 4.00 (Continued) 37 MB89130/130A Series (Continued) • One-time PROM products Resonator Resonator manufacturer* C1 (pF) C2 (pF) R 100 100 Not required Built-in Built-in Not required CSA4.00MG 30 30 Not required CSA4.00MGU 30 30 Not required Built-in Built-in Not required 100 100 Not required CST4.00MGWU040 Built-in Built-in Not required CSTCS4.00MG Built-in Built-in Not required CSA3.00MG040 CST3.00MGW040 Murata Mfg. Co., Ltd. CST4.00MGWU CSA4.00MGU040 Frequency (MHz) 3.00 4.00 Inquiry : Kyocera Corporation • AVX Corporation North American Sales Headquarters : TEL 1-803-448-9411 • AVX Limited European Sales Headquarters : TEL 44-1252-770000 • AVX/Kyocera H.K. Ltd. Asian Sales Headquarters : TEL 852-363-3303 Matsushita Electronic Components Co., Ltd. • North America Panasonic Industrial Co. : TEL 1-201-348-7000 • Canada Matsushita Electric of Canada Ltd. : TEL 905-238-2436 • Europe Panasonic Industrial Europe (Continental) : TEL 49-40-8549-2048 Panasonic Industrial Europe (Nlederlassung Munchen) : TEL 49-89-4800-7150 • Asia Panasonic Industry of Asia, Company : TEL 65-299-8400 Murata Mfg. Co., Ltd. • Murata Electronics North America, Inc. : TEL 1-404-436-1300 • Murata Europe Management GmbH : TEL 49-911-66870 • Murata Electronics Singapore (Pte.) Ltd. : TEL 65-758-4233 TDK Corporation • TDK Corporation of America Chicago Regional Office : TEL 1-708-803-6100 • TDK Electronics Europe GmbH Components Division : TEL 49-2102-9450 • TDK Singapore (PTE) Ltd. : TEL 65-273-5022 • TDK Hongkong Co., Ltd. : TEL 852-736-2238 • Korea Branch, TDK Corporation : TEL 82-2-554-6633 38 MB89130/130A Series • Sample Application of Crystal Resonator for Subclock Oscillation Circuit X0A X1A Rd ∗ C1 C2 • Mask ROM products Resonator manufacturer* SII Inquiry : Resonator Frequency (kHz) C1 (pF) C2 (pF) Ω) Rd (kΩ DS-VT-200 32.768 24 24 680 SII • Seiko Instruments Inc. (Japan) : TEL 81-43-211-1219 • Seiko Instruments U.S.A. Inc. : TEL 310-517-7770 • Seiko Instruments GmbH : TEL 49-6102-297-122 (6) Serial I/O Timing (VCC = +5.0 V ± 10%, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C) Symbol Pin Serial clock cycle time tSCYC SCK SCK ↓ → SO time tSLOV SCK, SO Valid SI → SCK ↑ tIVSH SI, SCK SCK ↑ → valid SI hold time tSHIX SCK, SI Serial clock “H” pulse width tSHSL Serial clock “L” pulse width tSLSH Parameter Condition Internal shift clock mode SCK SCK ↓ → SO time tSLOV Valid SI → SCK ↑ tIVSH External shift SCK, SO clock mode SI, SCK SCK ↑ → valid SI hold time tSHIX SCK, SI Value Unit Min. Max. 2 tinst* µs −200 200 ns 200 ns 200 ns 1 tinst* µs 1 tinst* µs 0 200 ns 200 ns 200 ns Remarks * : For information on tinst, see “ (4) Instruction Cycle.” 39 MB89130/130A Series • Internal Shift Clock Mode tSCYC SCK 2.4 V 0.8 V 0.8 V tSLOV 2.4 V SO 0.8 V tIVSH tSHIX 0.8 VCC 0.8 VCC 0.2 VCC 0.2 VCC SI • External Shift Clock Mode tSLSH tSHSL SCK 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC tSLOV 2.4 V SO 0.8 V tIVSH tSHIX 0.8 VCC 0.8 VCC 0.2 VCC 0.2 VCC SI 40 MB89130/130A Series (7) Peripheral Input Timing (VCC = +5.0 V ± 10%, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C) Parameter Symbol Pin Condition Peripheral input “H” level pulse width 1 tILIH1 Peripheral input “L” level pulse width 1 tIHIL1 EC, INT0 to INT2 Value Unit Remarks Min. Max. 2 tinst* µs 2 tinst* µs * : For information on tinst, see “ (4) Instruction Cycle.” tIHIL1 EC, INT0 to INT2 tILIH1 0.8 VCC 0.2 VCC 0.8 VCC 0.2 VCC 41 MB89130/130A Series 5. A/D Converter Electrical Characteristics (AVCC = VCC = +3.5 V to +6.0 V, FCH = 3 MHz, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C) Parameter Symbol Pin Condition Typ. Max. 8 bit ±1.5 LSB ±1.0 LSB ±0.9 LSB AVSS − 1.0 LSB AVSS + 0.5 LSB AVSS + 2.0 LSB mV AVR − 3.0 LSB AVR − 1.5 LSB AVR mV 0.5 LSB 44 tinst* µs 12 tinst* µs 10 µA 0 AVR V 2.0 AVCC V AVR = AVCC = 5.0 V, when A/D conversion is operating 100 300 µA AVR = AVCC = 5.0 V, when A/D conversion is not operating 1 µA Total error Linearity error Differential linearity error Zero transition voltage Full-scale transition voltage AVR = AVCC VOT — VFST Interchannel disparity A/D mode conversion time Sense mode conversion time Analog port input current IAIN Analog input voltage Reference voltage AN0 to AN3 IR AVR Reference voltage supply current IRH Unit Min. AVR = AVCC = 5.0 V Resolution Value Remarks 1LSB = AVR/256 * : For information on tinst, see “ (4) Instruction Cycle” in “4. AC Characteristics.” 6. A/D Converter Glossary • Resolution Analog changes that are identifiable by the A/D converter. When the number of bits is 8, analog voltage can be divided into 28 = 256. • Linearity error (unit : LSB) The deviation of the straight line connecting the zero transition point (“0000 0000” ↔ “0000 0001”) with the full-scale transition point (“1111 1111” ↔ “1111 1110”) from actual conversion characteristics • Differential linearity error (unit : LSB) The deviation of input voltage needed to change the output code by 1 LSB from the theoretical value 42 MB89130/130A Series • Total error (unit : LSB) The difference between theoretical and actual conversion values Digital output 1111 1111 1111 1110 Theoretical conversion value Actual conversion value 1 LSB = (1 LSB × N + VOT) AVR 256 Linearity error = Differential linearity error = Linearity error Total error = 0000 0010 0000 0001 0000 0000 VOT VNT V(N+1)T VFST VNT − (1 LSB × N + VOT) 1 LSB V(N+1)T − VNT 1 LSB −1 VNT − (1 LSB × N + 1 LSB) 1 LSB Analog input 43 MB89130/130A Series 7. Notes on Using A/D Converter • lnput impedance of the analog input pins The A/D converter used for the MB89130/130A series contains a sample hold circuit as illustrated below to fetch analog input voltage into the sample hold capacitor for eight instruction cycles after starting A/D conversion. For this reason, if the output impedance of the external circuit for the analog input is high, analog input voltage might not stabilize within the analog input sampling period. Therefore, it is recommended to keep the output impedance of the external circuit low (below 10 kΩ) . Note that if the impedance cannot be kept low, it is recommended to connect an external capacitor of approx. 0.1 µF for the analog input pin. • Analog Input Equivalent Circuit Analog input pin If the analog input impedance is higher than 10 kΩ, it is recommended to connect an external capacitor of approx. 0.1 µF. Sample hold circuit . C =. 28 pF . R =. 9 kΩ Close for 8 instruction cycles after starting A/D conversion. Analog channel selector • Error The smaller the | AVR − AVSS |, the greater the error would become relatively. 44 Comparator MB89130/130A Series ■ EXAMPLE CHARACTERISTICS (1) “L” Level Output Voltage (2) “H” Level Output Voltage VOL vs. IOL VCC – VOH vs. IOH VOL (V) VCC – VOH (V) VCC = 2.2 V 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 VCC = 2.5 V VCC = 3.0 V VCC = 4.0 V VCC = 5.0 V VCC = 6.0 V TA = +25 °C 0 1 2 3 4 5 6 7 8 9 10 IOL (mA) (3) “H” Level Input Voltage/“L” Level Input Voltage (CMOS Input) VIN (V) 5.0 4.5 TA = +25 °C 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 1 2 VCC = 2.2 V 1.1 1.0 TA = +25 °C 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 −0.5 −1.0 −1.5 −2.0 0.0 VIN (V) 5.0 4.5 TA = +25 °C 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1 2 0 4 5 6 VCC = 3.0 V VCC = 4.0 V VCC = 5.0 V VCC = 6.0 V −2.5 −3.0 IOH (mA) (4) “H” Level Input Voltage/“L” Level Input Voltage (Hysteresis Input) VIN vs. VCC 3 VCC = 2.5 V 7 VCC (V) VIN vs. VCC VIHS VILS 3 4 5 6 7 VCC (V) VIHS : Threshold when input voltage in hysteresis characteristics is set to “H” level VILS : Threshold when input voltage in hysteresis characteristics is set to “L” level (5) Pull-up Resistance RPULL vs. VCC RPULL (kΩ) 1000 TA = +25 °C 300 100 50 10 0 1 2 3 4 5 6 7 VCC (V) 45 MB89130/130A Series (6) Power Supply Current (External Clock) ICC1 vs. VCC ICCS1 vs. VCC ICC (mA) 5.0 4.5 4.0 Divide by 4(ICC1) FCH = 4.0 MHz TA = +25 °C ICCS1 (mA) 3 2.5 3.5 FCH = 4.0 MHz TA = +25 °C Divide by 4(ICCS1) Divide by 64 2 3.0 2.5 1.5 2.0 Divide by 64 1.5 1.0 1 0.5 0.5 0.0 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 VCC (V) TA = +25 °C 180 140 35 120 30 100 25 80 20 60 15 40 10 20 5 2.5 3 3.5 4 4.5 3 3.5 4 4.5 5 5.5 6 6.5 VCC (V) 5 5.5 6 6.5 VCC (V) TA = +25 °C 45 40 2 2.5 ICCLS (µA) 50 160 0 1.5 2 ICCLS vs. VCC ICCL vs. VCC ICCL (µA) 200 0.0 1.5 0 1.5 2 2.5 3 ICCT vs. VCC 3.5 4 4.5 5 5.5 6 6.5 VCC (V) IR vs. AVR ICCT (µA) 30 TA = +25 °C 25 IR (µA) 200 TA = +25 °C 180 160 140 20 120 15 100 80 10 60 40 5 20 0 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 VCC (V) 0 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 AVR (V) (Continued) 46 MB89130/130A Series (Continued) IA (mA) 5.0 4.5 4.0 ICCH vs. VCC IA vs. AVCC ICCH (µA) 2.0 FCH = 4 MHz TA = +25 °C 1.8 1.6 3.5 1.4 3.0 1.2 2.5 1.0 2.0 0.8 1.5 0.6 1.0 0.4 0.5 0.2 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 AVCC (V) TA = +25 °C 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 VCC (V) 47 MB89130/130A Series ■ MASK OPTIONS Part number MB89131 MB89133A MB89135A MB89P131 MB89P133A Specifying procedure Specify when ordering masking Specify when ordering masking Specify when ordering masking Selectable by pin (P40 to P43 must be fixed to no pull-up resistor option when an A/D converter is used.) Selectable by pin (P40 to P43 must be fixed to no pull-up resistor option when an A/D converter is used.) No. 1 Pull-up resistors •P00 to P07, P10 to P17, •P30 to P37, P40 to P43 Selectable by pin (P40 to P43 must be fixed to no pull-up resistor option when an A/D converter is used.) 2 Power-on reset •Power-on reset provided •No power-on reset Selectable Selectable Selectable 3 Selection of oscillation stabilization time •The oscillation stabilization time initial value is selectable from 4 types Selectable given below. 0 : Oscillation stabilization 22/FCH 1 : Oscillation stabilization 212/FCH 2 : Oscillation stabilization 216/FCH 3 : Oscillation stabilization 218/FCH Selectable Selectable 4 Reset pin output •Reset output enabled •Reset output disabled Selectable Selectable Selectable 5 Clock mode selection •Single-clock mode •Dual-clock mode Selectable Selectable Selectable 6 Selection of oscillation circuit type •Crystal or ceramic oscillation type Selectable •External clock input type Selectable Not required*1 7 Peripheral control clock output function*2 •Not used •Used Not required*3 Not required*3 Selectable *1 : Both external clock and oscillation resonator can be used on the OTPROM product. *2 : “Used” must be selected when P33 (39 pin) is used as SCO for the peripheral control clock output. *3 : The peripheral control clock output function can be used only by software. 48 MB89130/130A Series No. Part number MB89P135A MB89PV130A Specifying procedure Set with EPROM programmer Setting not possible 1 Pull-up resistors •P00 to P07, P10 to P17, •P30 to P37, P40 to P43 Selectable by pin All pins fixed to no pull-up resis(P40 to P43 must be fixed to no tor option pull-up resistor option.) 2 Power-on reset •Power-on reset provided •No power-on reset Selectable 3 Selection of oscillation stabilization wait time •The oscillation stabilization time initial value is selectable from 4 types given below. Selectable 0 : Oscillation stabilization 22/FCH 1 : Oscillation stabilization 212/FCH 2 : Oscillation stabilization 216/FCH 3 : Oscillation stabilization 218/FCH Oscillation stabilization 218/FCH 4 Reset pin output •Reset output enabled •Reset output disabled Selectable Reset output enabled 5 Selection of clock mode selection •Single-clock mode •Dual-clock mode Selectable Dual-clock mode 6 Selection of oscillation circuit type •Crystal or ceramic oscillation type Not required*1 •External clock input type Not required*1 7 Peripheral control clock output function*2 •Not used •Used Not required*3 Not required*3 Power-on reset provided *1 : Both external clock and oscillation resonator can be used. *2 : “Used” must be selected when P33 (39 pin) is used as SCO for the peripheral control clock output. *3 : The peripheral control clock output function can be used only by software. 49 MB89130/130A Series ■ MB89P131/P133A STANDARD OPTIONS No. Product option MB89P131-101 MB89P133A-201 1 Pull-up resistor Not provided for any port Not provided for any port 2 Power-on reset Provided Provided 3 Selection of oscillation stabiliza2 : Oscillation stabilization 216/FCH tion time 2 : Oscillation stabilization 216/FCH 4 Reset pin output Enabled Enabled 5 Selection of clock mode Dual-clock mode Dual-clock mode ■ ORDERING INFORMATION Part number MB89131PFM MB89133APFM MB89135APFM MB89P131PFM-101 MB89P133APFM-201 MB89P135APFM 50 Package 48-pin Plastic QFP (FPT-48P-M13) MB89133AP MB89P133AP-201 48-pin Plastic SH-DIP (DIP-48P-M01) MB89PV130ACF-ES 48-pin Ceramic MQFP (MQP-48C-P01) Remarks MB89130/130A Series ■ PACKAGE DIMENSION 48-pin Plastic QFP (FPT-48P-M13) 13.10±0.40(.516±.016)SQ 0.17±0.06 (.007±.002) 10.00±0.20(.394±.008)SQ 36 25 37 24 Details of "A" part +0.40 0.10(.004) 1.95 –0.20 +.016 .077 –.008 (Mounting height) 0.25(.010) INDEX 0~8° 48 13 1 0.80(.031) C "A" 12 0.32±0.05 (.013±.002) 0.20(.008) 0.80±0.20 (.031±.008) 0.88±0.15 (.035±.006) +0.10 0.20 –0.20 +.004 .008 –.008 (Stand off) M 2001 FUJITSU LIMITED F48023S-c-2-3 Dimensions in mm (inches) (Continued) 51 MB89130/130A Series 48-pin Plastic SH-DIP (DIP-48P-M01) +0.20 43.69 –0.30 +.008 1.720 –.012 INDEX-1 13.80±0.25 (.543±.010) INDEX-2 0.51(.020)MIN 5.25(.207) MAX 0.25±0.05 (.010±.002) 3.00(.118) MIN +0.50 1.00 –0 +.020 .039 –0 0.45±0.10 (.018±.004) 15.24(.600) TYP 15°MAX 1.778±0.18 (.070±.007) 1.778(.070) MAX C 40.894(1.610)REF 1994 FUJITSU LIMITED D48002S-3C-3 Dimensions in mm (inches) (Continued) 52 MB89130/130A Series (Continued) 48-pin Ceramic MQFP (MQP-48C-P01) 17.20(.677)TYP PIN No.1 INDEX 15.00±0.25 (.591±.010) 14.82±0.35 (.583±.014) 1.50(.059)TYP 8.80(.346)REF 1.00(.040)TYP 0.80±0.22 (.0315±.0087) PIN No.1 INDEX 1.02±0.13 (.040±.005) +0.13 10.92 –0.0 +.005 .430 –0 7.14(.281) 8.71(.343) TYP TYP PAD No.1 INDEX 0.30(.012)TYP +0.45 4.50(.177)TYP 1.10 –0.25 +.018 .043 –.010 0.40±0.08 (.016±.003) 0.60(.024)TYP 8.50(.335)MAX 0.15±0.05 (.006±.002) C 1994 FUJITSU LIMITED M48001SC-4-2 Dimensions in mm (inches) 53 MB89130/130A Series FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. F0110 FUJITSU LIMITED Printed in Japan