ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Discontinued Product These parts are no longer in production The device should not be purchased for new design applications. Samples are no longer available. Date of status change: May 1, 2006 Recommended Substitutions: NOTE: For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative. Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use. ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Package SB, 4-pin SIP 4 3 21 1. VCC 2. VOUT 3. Test pin (tie to GND) 4. GND ABSOLUTE MAXIMUM RATINGS Supply Voltage, VCC .......................................... 28 V Reverse-Supply Voltage, VRCC ........................ –18 V Reverse-Output Voltage, VROUT ...................... ??? V Continuous Output Current, IOUT .................. 20 mA Reverse Output Current, IROUT ...................... 50 mA Operating Temperature Ambient, TA, .............................. –40ºC to 150ºC Maximum Junction, TJ(max)........................170ºC Maximum Junction ≤ 100 hr, TJ(max) .........180ºC Storage Temperature, TS .................. –65ºC to 170ºC Package Thermal Resistance, RθJA ........... 150 °C/W The ATS672 true zero-speed gear tooth sensor IC provides manufacturer-friendly solutions for digital gear tooth sensing applications, through an optimized configuration of Hall-effect IC and rare earth pellet, packaged together in a single SIP (Single In Line Package). The SIP consists of an overmolded enclosure, which encapsulates a samarium cobalt pellet, a pole piece, and a true zero-speed Halleffect IC that has been optimized to the magnetic circuit. This package can be easily assembled and used in conjunction with gears of various shapes and sizes. The ATS672 incorporates a single-element Hall-effect IC that switches in response to the magnetic signal created by a ferromagnetic target (the gear). The IC contains a sophisticated digital circuit designed to eliminate the detrimental effects of magnet and system offsets. Signal processing is used to provide zero-speed performance, independent of air gap, and also to dynamically adapt device performance to the typical operating conditions found in automotive applications, such as reducing sensitivity to vibration. High resolution (9 bit) peak-detecting DACs are used to set the adaptive switching thresholds of the device. Hysteresis in the thresholds reduces the negative effects of any anomalies in the magnetic signal (such as magnetic overshoot) associated with the targets used in many automotive applications. The ATS672 also includes a low-bandwidth filter that increases the noise immunity and the signal-to-noise ratio of the IC. These features result in potential improvements in both the timing accuracy and the jitter performance of the device. The ATS672LSB version is optimized for gear tooth sensing applications. The ATS672LSB-LT is optimized for cam sensing. Features and Benefits • Tight timing accuracy throughout temperature range • True zero-speed operation • Air gap-independent switch points • Large operating air gaps • Single-chip solution for high reliability • Small mechanical dimensions • Optimized Hall-effect IC/magnetic systems • AGC and reference-adjust circuits • Operation down to 3.3 V • Undervoltage lockout • Digital output representing target profiles Use the following complete part numbers when ordering: Rev. 1.43 Part Number Package Application ATS672LSB 4-pin plastic SIP Gear tooth sensing ATS672LSB-LT 4-pin plastic SIP Cam sensing Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Functional Block Diagram VCC Regulator (Analog) Regulator (Digital) Dynamic Offset Cancellation Offset TC Low Pass Filter Automatic Gain Control (Analog) Amp TC Adjust VREF Threshold Comparator Output Driver Power On Reset VOUT VTHRESH GND Test 2 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture OPERATING CHARACTERISTICS Valid at Ta = –40ºC to 150ºC, and VCC within specification, unless otherwise noted Characteristics Symbol Test Conditions Min. Typ. Max. Units 3.3 – 26.5 V – – –18 V Electrical Characteristics Supply Voltage VCC Operating; TJ < TJ(max) Reverse Supply Voltage VRCC IRCC = –5 mA, maximum Supply Zener Clamp Voltage VZSupply ICC = 14 mA (≈ICC(max) + 3 mA); TA = 25°C 28 – – V Output Zener Clamp Voltage VZOutput IOUT = 3 mA; TA = 25°C 30 – – V Supply Zener Current IZSupply Test conditions only; VCC = 28 V – – ICC(max) + 3 mA Output Zener Current IZOutput VOUT = 30 V – – 3 mA Output = OFF 3 6.5 11 mA Output = ON 3 6.5 11 mA Gear Speed < 100 RPM; VCC > 3.3 V – – 500 μs – – < VCC(min) V ISINK = 15 mA, Output = ON – 0.2 0.45 V Supply Current ICC Power-On State Characteristics Power-On Time tPO Undervoltage Lockout VUV Output Stage Low Output Voltage VLOUT Output Current Limit Ilim Output = ON; TJ < TJ(max) 25 45 70 mA Output Leakage Current IOFF Output = OFF; VOUT = VCC(max) – – 10 μA Output Rise Time tr RLOAD = 500 Ω; CLOAD = 10 pF; TA = 25°C – 0.9 5 μs Output Fall Time tf RLOAD = 500 Ω; CLOAD = 10 pF; TA = 25°C – 0.5 5 μs Smax 0 – 8 kHz f – 3 dB – 40 – kHz – 30 – % – 40 – % Valley opposite the branded face of package – HIGH – Tooth opposite the branded face of package – LOW – – 2 3 – – 3 Switch Point Characteristics Tooth Speed Bandwidth Operate Point BOP Release Point BRP Output Polarity VOUT % of peak-to-peak, referenced to tooth sensing signal; AG < AGMax % of peak-to-peak, referenced to tooth sensing signal; AG < AGMax Calibration Initial Calibration CI AGC Disable Cf Number of rising mechanical edges on the target that are required for accurate edge detection Number of rising mechanical edges on the target that are required to complete the AGC calibration 3 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Output Rise Time (tr) and Fall Time (tf) VOUT (V) Output High 90% 100% 10% Output Low tr tf t (s) Output Voltage Rise Duration RLOAD = 500 Ω, CLOAD = 10 pF 10.00 VOUT (V) 8.00 6.00 4.00 2.00 0.00 0.0 1.0 2.0 3.0 4.0 5.0 t (μs) Output Voltage Fall Duration RLOAD = 500 Ω, CLOAD = 10 pF 10.00 VOUT (V) 8.00 6.00 4.00 2.00 0.00 0.0 1.0 2.0 3.0 4.0 5.0 t (μs) 4 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture OPERATING CHARACTERISTICS using reference target 8X and test circuit #1; air gap within AG range, and over rated ambient temperature range, unless otherwise noted Characteristics Symbol TICRel Relative Timing Accuracy* TRel Operational Air Gap Range *Relative AG Test Conditions During initial calibration; rising and falling mechanical edges; RPM = 1000; gear eccentricity < 0.1 mm After initial calibration; rising mechanical edge; RPM = 1000; gear eccentricity < 0.1 mm After initial calibration; falling mechanical edge; RPM = 1000; gear eccentricity < 0.1 mm Output switching: Running mode only Min. Typ. Max. Units – 3 6 deg. – 0.3 0.6 deg. – 0.5 0.8 deg. – 0.5 2.5 mm Timing Accuracy range is the change in edge position over the AG range and the device operating temperature range. ICC On, VCC = 4.0 V 10 10 8 8 ICC (mA) ICC (mA) ICC Off, VCC = 4.0 V 6 4 6 4 2 2 0 0 -40 25 TA (°C) 150 -40 25 TA (°C) 150 VSAT at ISINK = 15 mA, VCC = 4.0 V 450 VSAT (mV) 375 300 225 150 75 0 -40 25 150 TA (°C) 5 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Functional Description POR. (Power-On Reset) Allows complete reset to the original power-on state, when initial calibration occured, regardless of the state of the device immediately prior to POR. needed and minimal processing circuitry is required. This ease of use should reduce design time and incremental assembly costs for most applications. TC. (Temperature Coefficient) This supports fine tuning of the ATS672 for flat parametric performance over the full rated operating temperature range. Hall Technology. The device contains a single-chip Hall-effect IC, a 4-pin leadframe, and a specially-designed rare earth pellet. The Hall IC possesses a Hall element that measures the magnetic gradient created by the passing of a ferromagnetic object. The difference in the magnetic gradients created by a tooth and valley allow the generation of the digital output signal. The following output diagram corresponds to a customer application with the standard polarity. IC Integration. The ATS672 contains a self-calibrating Halleffect IC that possesses temperature compensated amplifier circuitry and a voltage regulator that provides supply noise rejection over the operating voltage range. The Hall transducer and the electronics are integrated on the same silicon substrate using a proprietary BiCMOS process. Changes in temperature do not greatly affect this device due to the stable amplifier design and the offset rejection circuitry. Assembly Description. The ATS672 is integrally molded into a plastic body that has been optimized for size, ease of assembly, and manufacturability. High operating temperature materials are used in all aspects of construction. Operation. When proper power is applied to the IC, it is capable of providing digital information that is representative of the profile of a rotating gear. No additional optimization is Rare Earth Pellet Digital Output Signal Magnetic Gradient Ferrous Target Mechanical Profile Rare Earth Pellet Hall technology. As the target moves by the package, there is a change in the magnetic flux density, B, which is measured in gauss (G). The left panel shows the effect of a tooth opposite the package, a higher B. The right panel shows the effect of a valley, a lower B. 6 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Start-Up Detection. The ATS672 generates a digital output transition when the first rising or falling mechanical edge is detected after being powered-on, indicating when the first significant motion in the target is detected. Undervoltage Lockout. When the supply voltage falls below the minimum operating voltage, VCCUV, the device turns off. It then stays off, regardless of the state of the magnetic field, until an operating range VCC is restored. It then turns on again. This lockout feature prevents false signals, caused by undervoltage conditions, from propagating to the output of the IC. Power Supply Protection. The device contains an on-chip regulator and can operate over a wide VCC range. For devices that need to operate from an unregulated power supply, transient protection must be added externally. For applications using a regulated line, EMI/RFI protection may still be required. Contact Allegro Microsystems for information on the circuitry needed for compliance with various EMC specifications. Automatic Gain Control (AGC). The patented self-calibrating circuitry is unique. Each time the device is powered-on, the device starts measuring the peak-to-peak magnetic gradient. The gain of the IC is automatically adjusted, keeping the internal electrical signal amplitude constant over the air gap range, AG, of the device. This feature provides consistent operational characteristics independent of variances in the air gap. Switch Points. Switch points are the levels of magnetic flux density, B, which trigger switch turn-on and turn-off. When B exceeds a certain limit, referred to as the Operate point (Bop), the trigger provides a clean transition from off to on. When the magnetic field falls below Bop by a certain limit, referred to as the Release point, Brp, the trigger provides a clean transition from on to off. In the ATS672, switch points are established dynamically as a percentage of the amplitude of the normalized magnetic signal. Two DACs track the peaks of the normalized magnetic signal, and the switching thresholds are established at fixed percentages of the two DAC values. The values of the thresholds have been carefully selected to provide the most accurate and consistent switching where the signal is steepest and least affected by air gap variation. The figure below graphically demonstrates the establishment of the switching threshold levels. The low hysteresis of 10% provides high performance over the full AG, and immunity to false switching due to noise, vibration, backlash, or other transient events. Electrical Signal Response, with AGC V AGMax AGMin Valley Signal AGMin Magnetic Gradient (No amplification) AGMax Bop Brp Bop% Brp% 100% Bhys Tooth Signal Switch Points. The ATS672 design minimizes hysteresis, Bhys. t Ferrous Target Mechanical Profile Automatic Gain Control (AGC). The AGC function corrects for variances in the air gap. Differences in the air gap affect the magnetic gradient, but AGC prevents that from affecting device performance. 7 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Application Information For additional general application information, visit the Allegro MicroSystems Web site at www. allegromicro.com. Target Design The Hall-effect IC can detect variations in magnetic flux density generated by features of a target. To distinguish between two features of a target, such as between a tooth and a valley of a spur gear, there must be a minimum differential of 120 G in the magnetic flux densities corresponding to the features, as measured at the Hall element. The target must be mounted with an air gap in the range AG, the distance between the target object and the plane of the Halleffect element as installed. In general, the nearer a target feature is to the element, the greater the magnetic flux density at the element. The following figures and table specify a design that can be used to construct a reference target. The target represents a ferrous spur gear, with uniform tooth and valley widths. The target would be mounted so that its axis of rotation is parallel to the plane of the Hall-effect element, and centered on the element. When the target is produced to the specifications listed in the Reference Target column of the table, the required differential (tooth peak to valley) in magnetic flux densities is generated. Also in the table, the Minimum Required for TPOS column provides specifications for a similar application. These values are the minimum required for the TPOS function to operate accurately, as defined in the Operating Characteristics table. Active Area of IC Target Branded face of Package 8X Reference Target Reference Target Characteristics Characteristic Material Diameter Description Reference Target 8X Only Minimum Required for TPOS Units Target has uniform composition CRS1018 – – 120 – mm Symbol DO Diameter of target, to valley Tooth Thickness F Breadth of tooth, with respect to branded face of package 6 5 mm Tooth Height Ht Height of tooth, measured from the valley (DO) 5 5 mm Tooth Width T Width of tooth 22.5* 5 deg. Valley Width PC – T Width of valley, with PC = pitch of teeth 22.5* 13 deg. *Resulting arc measures 23.6 mm in length at DO 8 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Typical Circuit Design IC/Target Evaluation The following circuit is the most basic configuration required for proper device operation. A pull-up resistor is used. In order to establish the proper operating specification for a particular IC/target configuration, a systematic evaluation of the magnetic circuit should be performed. The first step is the generation of a magnetic map of the target. By using a calibrated device, a magnetic signature of the system is made. A magnetic map of the 8X reference target, created using the LSB package, is shown below. VCC 1 0.1 uF 2 ATS672 3 From this map data, a pair of curves can be derived that describe the tooth and valley magnetic fields versus air gap. Knowing the minimum amount of magnetic flux density that guarantees operation of the IC, one can determine the maximum operational air gap of the IC/target system. 4 VOUT Magnetic Map, 8X Reference Target, Using LSB Package 500 Magnetic Flux Density, B (G) 450 400 350 300 250 200 150 100 50 0 -50 -100 -150 -200 0 30 60 90 120 150 180 210 240 270 300 330 360 Position (°) Magnetic Flux Density, B, Versus Air Gap 8X Reference Target Using LSB Package Magnetic Flux Density, B (G) 600 500 400 300 200 Tooth 100 0 Valley -100 -200 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 Air Gap (mm) 9 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture DEVICE EVALUATION: ACCURACY The self-calibration algorithm allows the IC to adapt to system changes such as air gap increase. However, major changes in air gap can adversely affect switching performance. When characterizing IC performance over a significant air gap range, be sure Edge Position vs. Air Gap Electrical Rising Edge (Mechanical Falling Edge) ATS672LSB; 8X Reference Target 105 Edge Position (Degrees) to power-off and then power-on the device at each air gap. This ensures that self-calibration occurs for each installation condition. See the Operating Characteristics table for information on timing accuracy performance. ROOM 150ºC -40ºC 104.8 104.6 104.4 104.2 104 103.8 103.6 103.4 103.2 103 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 Air Gap (mm) Edge Position vs. Air Gap Electrical Falling Edge (Rising Mechanical Edge) ATS672LSB; 8X Reference Target Edge Position (Degrees) 127 ROOM 150ºC -40ºC 126.8 126.6 126.4 126.2 126 125.8 125.6 125.4 125.2 125 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 Air Gap (mm)) Relative Timing Accuracy Target Operational Air Gap Valley Tooth Air Gap Device Output TAbsRise (Max - Min) TAbsFall (Max - Min) 10 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Temperature Compensation The device should be operated at or below the maximum junction temperature of the device, TJ(max) (see the Absolute Maximum Ratings section, on page 1). The actual operating TJ of the device is affected by several factors. Under certain combinations of peak conditions (corresponding to the gray area of the Power De-Rating Curve chart), operation may require power de-rating or heat sinking. The relevent factors are characteristic of the device and package, as well as the application, including the effect of adjacent external sources of heat. The Package Thermal Resistance, RJA, indicates the resitance to heat transfer from the heat-generating portions of the die (the “junction”) through all paths to the ambient air. This includes heat sinking through the PCB, and radiation from the die through the case, RCA. Thermal information on packages is available on the Allegro Microsystems Web site. The Allowable Power Dissipation, PD, represents the amount of power that can be applied to the device at a given RJA and ambient temperature, TA, without causing the temperature of the die to exceed TJ(max). This section presents a procedure for correlating these factors with operating voltage, VCC, and operating current, ICC, to estimate their effect on TJ. If the estimated operating TJ exceeds TJ(max), then power levels can be reduced or external heat sinking can be applied. Typically, VCC is the factor reduced, to accommodate the required TA. A power de-rating curve can be constructed, representing the maximum allowable VCC per TA. If the calculated VCC exceeds the power de-rating curve at the required TA, and heat sinking is not preferred, estimate the amount to reduce VCC. This can be estimated through calculating PD(max), the maximum allowable PD for the given device and package. PD(max) is related to RJA and TA. The following formulas represent the fundamental relationships used to calculate the VCC adjustment, based on the temperature effect, ΔT. TJ = TA + ΔT (1) where T denotes the increase in TJ due to power dissipation within the device. T = PD × RJA (2) PD = VCC × ICC (3) Examples for estimating VCC are provided on the next page. These formulas and results can also be used to estimate TJ. For example, given common conditions such as: TA= 25°C, VCC = 5 V, ICC(on) = 6.5 mA, and RJA = 150 °C/W then: PD = VCC × ICC(on) = 5 V × 6.5 mA = 32.5 mW T = PD × RJA = 32.5 mW × 150 °C/W = 4.9°C TJ = TA + T = 25°C + 4.9°C = 29.9°C Maximum Allowable VCC (V) Power De-Rating Curve VCC(max) = 26.5 V; TJ(max) = 170ºC 28.0 26.0 24.0 22.0 20.0 18.0 16.0 14.0 12.0 10.0 8.0 6.0 4.0 2.0 0.0 Allowable operating range without additional heat sinking Some combinations of peak ratings may require heat sinking when operating in shaded area 20 40 60 80 100 120 140 160 180 TA (ºC) 11 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Example: VCC Adjustment, Package SE Observe the absolute maximum ratings for the package, specifically: RJA = 150 °C/W TJ(max) = 170°C Also observe the characteristic operating maximums: VCC(max) = 26.5 V ICC(max) = 11 mA For a given TA (e.g., 150°C), first calculate the Maximum Allowable Power Dissipation, PD(max). Invert equation 1: Tmax = TJ(max) – TA = 170°C – 150°C = 20°C This provides the allowable increase to TJ resulting from internal power dissipation. Then, invert equation 2: PD(max) = Tmax ÷ RJA = 20°C ÷ 150 °C/W = 133 mW This provides the corresponding allowable increase in power level. Finally, invert equation 3 to determine the corresponding supply voltage VCC: VCC = PD(max) ÷ ICC(max) = 133 mW ÷ 11 mA = 12 V The result indicates that the device and package can dissipate adequate amounts of heat at voltages up to 12 V, at TA = 150ºC. Because VCC(max) is more than the calculated VCC, however, the device requires additional heat sinking for operation between the calculated VCC and VCC(max), under these conditions. If the calculated VCC were greater than or equal to VCC(max), then operation up to VCC(max) would not require additional heat sinking. PD(max) (m W) Maxim um Pow er Dissipation vs. Am bient Temperature Package SB: RθJA = 150ºC/W, TJ(max) = 170ºC 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 20 40 60 80 100 120 140 160 180 TA (ºC) 12 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture Package SB, 4-pin SIP AAD 0.42 13 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com ATS672LSB Self-Calibrating Gear Tooth Sensor IC with 9-Bit Signal Capture The products described herein are manufactured under one or more of the following U.S. patents: 5,045,920; 5,264,783; 5,442,283; 5,389,889; 5,581,179; 5,517,112; 5,619,137; 5,621,319; 5,650,719; 5,686,894; 5,694,038; 5,729,130; 5,917,320; and other patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Copyright © 2004-2009 Allegro MicroSystems, Inc. 14 Rev. 1.43 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com