Datasheet

UNISONIC TECHNOLOGIES CO., LTD
U74LVC2G08
CMOS IC
DUAL 2-INPUT AND GATE

DESCRIPTION
The U74LVC2G08 is a dual 2-input AND gate which performs the
MSOP-8
function Y=A*B or Y=A  B . It is designed for 1.65V to 5.5V
operation.

FEATURES
* Wide Supply Voltage Range from 1.65V to 5.5V
* Max tPD of 4.7 ns at 3.3V
* Up to 5V Inputs Accept Voltages
* Low Power Consumption, ICC = 10 μA (Max.)
* ±24 mA Output Driver at 3V
* Direct Interface with TTL Levels

ORDERING INFORMATION
Ordering Number
U74LVC2G08G-SM1-R
U74LVC2G08G-P08-R

TSSOP-8
Package
MSOP-8
TSSOP-8
Packing
Tape Reel
Tape Reel
MARKING
MSOP-8
www.unisonic.com.tw
Copyright © 2015 Unisonic Technologies Co., Ltd
TSSOP-8
1 of 5
QW-R502-437.D
U74LVC2G08
CMOS IC

PIN CONFIGURATION

FUNCTION TABLE (Each Gate)
INPUTS
A
L
L
H
H

B
L
H
L
H
OUTPUT
Y
L
L
L
H
LOGIC DIAGRAM (Positive Logic)
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2 of 5
QW-R502-437.D
U74LVC2G08

CMOS IC
ABSOLUTE MAXIMUM RATING (Note)
PARAMETER
SYMBOL
RATINGS
UNIT
Supply Voltage
VCC
-0.5~6.5
V
Input Voltage
VIN
-0.5~6.5
V
Output Voltage (Active Mode)
VOUT
-0.5~VCC+0.5
V
Output Voltage (Power-Down Mode)
VOUT
-0.5~+6.5
V
Input Clamp Current
IIK
-50
mA
Output Clamp Current
IOK
±50
mA
Output Current
IOUT
±50
mA
VCC or GND Current
ICC
±100
mA
Power Dissipation
PTOT
300
mW
Storage Temperature
TSTG
-65 ~ +150
°C
Notes: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

RECOMMENDED OPERATING CONDITIONS
PARAMETER
Supply Voltage
Input Voltage
SYMBOL
VCC
VIN
Output Voltage
VOUT
Input Transition Rise or Fall Rate
tR / tF
Operating Temperature
TOPR

CONDITIONS
Operating
Active Mode
Power-Down Mode; VCC = 0V;
VCC=1.65V to 2.7V
VCC=2.7V to 5.5V
MIN
1.65
0
0
0
TYP
-40
MAX UNIT
5.5
V
5.5
V
VCC
V
5.5
20
ns/V
10
125
°C
ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified)
PARAMETER
High-Level Input Voltage
Low-Level Input Voltage
High-Level Output Voltage
Low-Level Output Voltage
Input Leakage Current
OFF-state Current
Quiescent Supply Current
Additional quiescent Supply
Current
Input Capacitance
SYMBOL
VIH
VIL
VOH
VOL
II(LEAK)
IOFF
IQ
 IQ
TEST CONDITIONS
MIN
0.65×V
VCC = 1.65V to 1.95V
CC
VCC = 2.3V to 2.7V
1.7
VCC = 2.7V to 3.6V
2.0
0.7×VCC
VCC = 4.5V to 5.5V
VCC = 1.65V to 1.95V
VCC = 2.3V to 2.7V
VCC = 2.7V to 3.6V
VCC = 4.5V to 5.5V
IOH = -100μA VCC = 1.65V to 5.5V VCC -0.1
IOH = -4mA
VCC = 1.65V
1.2
IOH = -8mA
VCC = 2.3V
1.9
IOH = -12mA VCC = 2.7V
2.2
IOH = -24mA VCC = 3V
2.3
IOH = -32mA VCC = 4.5V
3.8
IOL = 100μA VCC = 1.65V to 5.5V
IOL = 4mA
VCC = 1.65V
IOL = 8mA
VCC = 2.3V
IOL = 12mA VCC = 2.7V
IOL = 24mA VCC = 3.0V
IOL = 32mA VCC = 4.5V
VIN = 5.5V or GND, VCC = 5.5V
VIN or VO = 5.5V, VCC = 0V
VIN = VCC or GND, IOUT= 0, VCC= 5.5V
One input at VCC – 0.6V; other inputs
at VCC or GND; VCC=2.3V to 5.5V
CIN
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
TYP
MAX
UNIT
V
0.35×VCC
0.7
0.8
0.3×VCC
1.53
2.13
2.50
2.60
4.10
V
V
0.08
0.14
0.19
0.37
0.43
±0.1
±0.1
0.1
0.1
0.45
0.3
0.4
0.55
0.55
±5
±10
10
μA
μA
μA
5
500
μA
2.5
V
pF
3 of 5
QW-R502-437.D
U74LVC2G08

SWITCHING CHARACTERISTICS (TA =25°C)
PARAMETER
Propagation delay from input
(A or B) to output (Y)

CMOS IC
SYMBOL
tPLH / tPHL
TEST CONDITIONS
VCC=1.8V±0.15V, RL=1KΩ
CL=30pF
VCC=2.5V±0.2V, RL=500Ω
VCC=2.7V, RL=500Ω
VCC=3.3V±0.3V, RL=500Ω CL=50pF
VCC=5.0V±0.5V, RL=500Ω
MIN
1.0
0.5
1.0
0.5
0.5
TYP
3.2
2.2
2.5
2.1
1.7
MAX
9.0
5.1
5.3
4.7
3.8
UNIT
MIN
TYP
14.4
MAX UNIT
pF
ns
OPERATING CHARACTERISTICS (TA =25°C)
PARAMETER
SYMBOL
TEST CONDITIONS
Power Dissipation Capacitance
CPD
VCC = 3.3V
Notes: 1. CPD is used to determine the dynamic power dissipation (PD in μW).
PD  C P D  V C2C  f i  N   ( C L  V C2C  f O ) , where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in Volts;
N = total load switching outputs;
 ( C L  V C2C  f O ) = sum of outputs.
2. The condition is VI = GND to VCC.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
4 of 5
QW-R502-437.D
U74LVC2G08

CMOS IC
TEST CIRCUIT AND WAVEFORMS
From Output
CL
RL
INPUTS
VCC
VIN
VCC
VCC
2.7V
2.7V
VCC
1.65 V to 1.95 V
2.3 V to 2.7 V
2.7 V
3.0 V to 3.6 V
4.5 V to 5.5 V
tR, tF
≤2ns
≤2ns
≤2.5ns
≤2.5ns
≤2.5ns
VM
CL
RL
VCC/2
VCC/2
1.5V
1.5V
VCC/2
30pF
30pF
50pF
50pF
50pF
1KΩ
500Ω
500Ω
500Ω
500Ω
VIN
Input
VM
VM
0V
t PHL
t PLH
VOH
Output
VM
VM
VOL
Notes: 1. CL includes probe and jig capacitance.
2. All input pulses are supplied by generators having the following characteristics: PRR ≤1 MHz, ZO = 50 Ω,
tR ≤ 3 ns, tF ≤ 3 ns.
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 5
QW-R502-437.D