UNISONIC TECHNOLOGIES CO., LTD U74HC1G06 CMOS IC SINGLE INVERTER WITH OPEN-DRAIN OUTPUTS DESCRIPTION The U74HC1G06 is a single inverting buffer with open-drain outputs and it provides the function Y= A in positive logic. For digital operation the outputs of this device must have a pull-up resistor to establish a logic HIGH-level. FEATURES * Wide supply voltage range from 2V to 6V * High noise immunity * Low power dissipation; ICC=1μA (Max.) * Typical tPD=6ns at VCC=6V ORDERING INFORMATION Ordering Number Lead Free Plating Halogen Free U74HC1G06L-AE5-R U74HC1G06G-AE5-R U74HC1G06L-AL5-R U74HC1G06G-AL5-R Package Packing SOT-23-5 SOT-353 Tape Reel Tape Reel MARKING www.unisonic.com.tw Copyright © 2013 Unisonic Technologies Co., Ltd 1 of 5 QW-R502-884.A U74HC1G06 PIN CONFIGURATION FUNCTION TABLE INPUT(A) H L Note: H: HIGH voltage level; CMOS IC OUTPUT(Y) L Z L: LOW voltage level; Z: high impedance state. LOGIC DIAGRAM (positive logic) Logic symbol UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw IEC logic symbol 2 of 5 QW-R502-884.A U74HC1G06 CMOS IC ABSOLUTE MAXIMUM RATING PARAMETER SYMBOL RATINGS UNIT Supply Voltage VCC -0.5 ~ 7.0 V Input Voltage VIN -0.5 ~ VCC +0.5 V Output Voltage VOUT -0.5 ~ VCC +0.5 V VCC or GND Current ICC ±50 mA Continuous Output Current (VOUT=0 to VCC ) IOUT ±25 mA Input Clamp Current (VIN<0) IIK ±20 mA Output Clamp Current (VOUT<0) IOK ±20 mA Storage Temperature Range TSTG -65 ~ +150 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. RECOMMENDED OPERATING CONDITIONS PARAMETER Supply Voltage Input Voltage Output Voltage Low-level Output Current Operating Temperature Input Transition Rise or Fall Rate SYMBOL VCC VIN VOUT IOL TEST CONDITIONS TYP VCC=2.0V VCC=4.5V VCC=6.0V VCC=4.5V VCC=6.0V TA Δt/Δv MIN 2 0 0 -40 VCC=2.0V VCC=4.5V VCC=6.0V MAX 6 VCC VCC 20 20 20 4.0 5.2 85 500 112 67 UNIT V V V uA MAX 0.5 1.35 1.8 0.1 0.1 0.1 0.26 0.26 ±0.1 UNIT V V V V V V V V V V V μA ±0.5 μA 1.0 μA pF pF uA mA °C ns/V ELECTRICAL CHARACTERISTICS (TA=25°C, unless otherwise specified) PARAMETER High-level Input Voltage Low-level Input Voltage Low-Level Output Voltage Input Leakage Current Output Leakage Current Quiescent Supply Current Input Capacitance Output Capacitance SYMBOL VIH VIL VOL II(LEAK) IOZ ICC CI COUT TEST CONDITIONS VCC=2.0V VCC=4.5V VCC=6.0V VCC=2.0V VCC=4.5V VCC=6.0V VCC=2.0V VCC=4.5V IOL=20μA VCC=6.0V VCC=4.5V IOL=4.0mA VCC=6.0V IOL=5.2mA VCC=0~6V, VIN= VCC or GND VCC=6.0V, VIN=VIL or VIH, VOUT= VCC or GND VCC=6.0V, VIN= VCC or GND, IOUT=0 VCC=5.0V VCC =5.0V UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN 1.5 3.15 4.2 TYP 0 0 0 0.17 0.18 5 3 3 of 5 QW-R502-884.A U74HC1G06 CMOS IC SWITCHING CHARACTERISTICS (TA=25°C) See Fig. 1 and Fig. 2 for test circuit and waveforms. PARAMETER SYMBOL TEST CONDITIONS VCC=2.0V Output transition time tTHL VCC=4.5V VCC=6.0V VCC=2.0V, Propagation delay from input tPLZ. CL=50pF, RL=1kΩ VCC=4.5V (A ) to output(Y) VCC=6.0V VCC=2.0V Propagation delay from input tPZL VCC=4.5V CL=50pF, RL=1kΩ (A) to output(Y) VCC=6.0V MIN TYP 30 8 7 10 7 6 17 7 5 MAX 75 15 13 90 18 15 90 18 15 UNIT TYP 4.0 MAX UNIT pF ns ns ns OPERATING CHARACTERISTICS (TA=25°С) PARAMETER Power Dissipation Capacitance SYMBOL TEST CONDITIONS CPD VCC=5.0V, CL=50pF,f =1MHz UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN 4 of 5 QW-R502-884.A U74HC1G06 CMOS IC TEST CIRCUIT AND WAVEFORMS Note: 1. Since this device has open drain outputs, the tPLZ and tPZL is the same as tPLH and tPHL . Fig. 1 LOAD CIRCUITRY FOR SWITCHING TIMES VCC VCC=2.0V VCC=4.5V VCC=6.0V VIN VCC VCC VCC tR / tF 6ns 6ns 6ns VM VCC/2 VCC/2 VCC/2 VLOAD 2×VCC 2×VCC 2×VCC CL 50pF 50pF 50pF RL 1kΩ 1kΩ 1kΩ VΔ 0.3V 0.3V 0.3V Fig. 2 PROPAGATION DELAY FROM INPUT(A) TO OUTPUT(Y) AND OUTPUT TRANSITION TIME Note: 1. CL includes probe and jig capacitance. 2. All input pulses are supplied by generators having the following characteristics: PRR ≤10MHz, Zo = 50Ω. UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 5 QW-R502-884.A