Model 50 SHE Datasheet

Model 50 SHE
www.vishay.com
Vishay Sfernice
Single Turn Servo Mount Hall Effect Sensor in Size 05 (12.7 mm)
FEATURES
• Accurate linearity down to: ± 0.5 %
• All electrical angles available up to: 360°
(no dead band)
• Long life: Greater than 50M cycles
• Non contacting technology: Hall effect
• Smallest size available
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
QUICK REFERENCE DATA
Sensor type
Output type
Market appliance

ROTATIONAL, single turn hall effect
Wires
Professional
Dimensions
½" (12.7 mm) dia.
ELECTRICAL SPECIFICATIONS
PARAMETER
STANDARD
SPECIAL
Electrical angle
90°, 180°, 270°, 360°
Any other angle upon request
Linearity
±1%
± 0.5 %
5 VDC ± 10 %
Other upon request
Supply current
10 mA typical/16 mA max.
16 mA for PWM output
Output signal
Analog ratiometric 10 % to 90 % of Vsupply or
PWM 1 kHz, 10 % to 90 % duty cycle
Other upon request
Supply voltage
Over voltage protection
+20 VDC
Reverse voltage protection
-10 VDC
Load resistance recommended
Min. 1 k for analog output and PWM output
Hysteresis static
< 0.2° max.
MECHANICAL SPECIFICATIONS
PARAMETER
Mechanical travel
360° continuous
Bearing type
2 ball bearings
Standard
IP 51; other on request
ORDERING INFORMATION/DESCRIPTION
50 SHE
1
A
1
W
A
2S13
XXXX
BO 10
e1
MODEL
NUMBER
OF CUP
LINEARITY
ELECTRICAL
ANGLE
OUTPUT
TYPE
OUTPUT
SIGNAL
SHAFT
TYPE
SPECIAL
REQUEST
PACKAGING
LEAD
FINISH
1:1 Cup
A: ± 1 %
B: ± 0.5 %
1: 90°
2: 180°
3: 270°
4: 360°
9: Other
angles
W: Wires A: Analog CW 2: 3.175 mm
Z:
B: Analog CCW 9: Special
P: Plain
Custom
C: PWM CW
S: Slotted
D: PWM CCW
Z: Other
Z: Other output
type
Box of 10
pieces
Shaft length from mounting face, standard: 13 mm
SAP PART NUMBERINGGUIDELINES
50 SHE
1
B
9
Z
C
2P22
XXXX
MODEL
1: 1 cup
OUTPUT
SIGNAL
LINEARITY
ELECTRICAL
ANGLE
OUTPUT TYPE
OUTPUT
SIGNAL
SHAFT TYPE
SPECIAL
REQUEST
Revision: 27-Mar-15
Document Number: 57104
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Model 50 SHE
www.vishay.com
Vishay Sfernice
VOUT ANALOG
Operating temperature
85 °C
125 °C
Diagnostic high level
96 % min.
96 % min.
Diagnostic low level
2 % max.
4 % max.
Vout
(% Vsupply)
Vout
(% Vsupply)
Diagnostic High Area
Diag High Level
90 %
Diagnostic High Area
Diag High Level
90 %
CCW
CW
10 %
Diag Low Level
10 %
Diag Low Level
Diagnostic Low Area
0
Theta
(Position)
Diagnostic Low Area
0
Theta
(Position)
VOUT PWM
Vout
(% Vsupply)
CW
97 % min.
T high
Duty Cycle =
Thigh
T
T low
1.5 % max.
0
Time (µs)
T: periodicity
Revision: 27-Mar-15
Document Number: 57104
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Model 50 SHE
www.vishay.com
Vishay Sfernice
DIAGNOSTIC MODES
Vout ANALOG
Rpull-up
Vout ANALOG
Rpull-down
Vout PWM
Rpull-up = 1 k
Vpull-up = Vsupply = 5 V
1: Broken GND
Diagnostic high area
Diagnostic low area
> 97 % Vsupply
without modulation
2: Broken Vout
Diagnostic high area
Diagnostic low area
> 97 % Vsupply
without modulation
3: Broken Vsupply
Diagnostic high area
Diagnostic low area
> 97 % Vsupply
without modulation
Over Voltage Vsupply > 7 V
Diagnostic high area
Diagnostic low area
> 97 % Vsupply
without modulation
Under Voltage Vsupply < 2.7 V
Diagnostic high area
Diagnostic low area
> 97 % Vsupply
without modulation
FAILURE
Vpull-up
Vsupply
3
Rpull-up
Vpull-up can be independent to Vsupply
Sensor
2
GND
Vout
1
Cut off
ENVIRONMENTAL SPECIFICATIONS
Vibrations
Shocks
20 g from 10 Hz to 2000 Hz, EN 60068-2-6
3 shocks/axis; 50 g half a sine 11 ms, EN 60068-2-7
Operating temperature range
-40 °C; +125 °C
Life
> 50M of cycles
Rotational speed (max.)
Immunity to radiated electromagnetic disturbances
120 rpm
200 V/m 150 kHz/1 GHz, IEC 62132-2 part 2 (level A)
Immunity to power frequency magnetic field
Radiated electromagnetic emissions
200 A/m 50 Hz/60 Hz, EN 61000-4-8 (level A)
30 MHz/1 GHz < 30 dBμV/m, EN 61000-6-4 (level A)
Electrostatic discharges
Contact discharges: ± 4 kV
Air discharges: ± 8 kV, EN 61000-4-2
MATERIALS
Housing
Shaft
Output
Aluminum
Stainless steel
3 lead wires (AWG 24)
Note
• Nothing stated herein shall be construed as a guarantee of quality or durability.
Revision: 27-Mar-15
Document Number: 57104
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Model 50 SHE
www.vishay.com
Vishay Sfernice
DIMENSIONS in millimeters
12.7 ± 0.8
Ø 11 ± 0.1
0.4 x 45°
Ø 3.175 max. - 0.013
Ø 12.6 ± 0.1
19.5 ± 0.5
1.6 ± 0.1
Ø 12.6 ± 0.1
1.6 ± 0.1
Ø 9.5 ± 0.013
0
1.6 ± 0.1
AWG 24
l = 300 mm
3 wires
CW or CCW according
to output mode choice
1:1
Vsupply = Green wire
GND = Yellow wire
Vout = Red wire
General tolerance: ± 0.5 mm
Revision: 27-Mar-15
View from shaft side
Document Number: 57104
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000