Datasheet

Photomicrosensor (Transmissive)
EE-SX3096-W11/4096-W11
Be sure to read Precautions on page 24.
■ Dimensions
■ Features
Note: All units are in millimeters unless otherwise indicated.
• Light-receiving element and amplification circuits contained in one
chip.
• Can use a power supply voltage of 4.5 to 16 V.
• Connects directly to C-MOS or TTL.
• Dark-ON Sensor: EE-SX3096-W11
• Light-ON Sensor: EE-SX4096-W11
• Pre-wired Sensors (AWG28).
• Solder-less lead wire connection to increase reliability.
• With a horizontal aperture.
25±0.2
Two, R1
19±0.15
Optical axis
6±0.2 5±0.2
Two, 3.2±0.2 dia. holes
Emitter
B
2.1±0.15
Sensing
window
Two, C2
Four, C0.3
12.6±0.2
3.4±0.2
Detector
A
Optical axis
2.1±0.15
■ Absolute Maximum Ratings (Ta = 25C)
10±0.2
0.5±0.1
7.2±0.2
0.5±0.1
3.1
Item
Emitter
2.5±0.1
Symbol
IF
50 mA
(see note 1)
Reverse voltage
VR
4V
Power supply voltage
VCC
16 V
Output voltage
VOUT
28 V
Output current
IOUT
16 mA
610MIN
O
V
G
K
A
4
Four, Wires UL1061,
AWG#28
Cross section A-A
3.55
Cross section B-B
11.6±0.2
B
Internal Circuit
A
Detector
A
G
O
K
V
Terminal Color
Name
No.
A
Red Anode
K
V
Black Cathode
White Power supply
(Vcc)
O
Blue
G
Green Ground (GND)
Permissible output POUT
dissipation
Unless otherwise specified, the
tolerances are as shown below.
Output (OUT)
Dimensions
Ambient temperature
Tolerance
3 mm max.
±0.3
3 < mm ≤ 6
±0.375
6 < mm ≤ 10
±0.45
10 < mm ≤ 18
±0.55
18 < mm ≤ 30
±0.65
Rated value
Forward current
250 mW
(see note 1)
Operating
Topr
–25C to 75C
Storage
Tstg
–25C to 85C
Note: 1. Refer to the temperature rating chart if the ambient temperature exceeds 25C.
2. If you mount the Sensor with screws, use M3 screws, spring
washers, and flat washers and use a tightening torque of 0.5
N·m max.
3. You should use the product in the condition without any
stress on the cable.
■ Electrical and Optical Characteristics (Ta = 25C)
Item
Symbol
Value
Condition
Forward voltage
VF
1.2 V typ., 1.5 V max.
IF = 20 mA
Reverse current
IR
0.01 A typ., 10 A max.
VR = 4 V
Peak emission wavelength
P
940 nm
IF = 20 mA
Low-level output voltage
VOL
0.12 V typ., 0.4 V max.
VCC = 4.5 to 16 V, IOL = 16 mA, IF = 0 mA (EE-SX3096),
IF = 5 mA (EE-SX4096)
High-level output voltage
VOH
15 V min.
VCC = 16 V, RL = 1 k, IF = 5 mA (EE-SX3096),
IF = 0 mA (EE-SX4096)
Current consumption
ICC
3.2 mA typ., 10 mA max.
VCC = 16 V
870 nm
VCC = 4.5 to 16 V
IFT
2 mA typ., 5 mA max.
VCC = 4.5 to 16 V
Hysteresis
H
15% typ.
VCC = 4.5 to 16 V (see note 1)
Response frequency
f
3kHz min.
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 2)
Response delay time
tPLH (tPHL)
3 s typ.
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 3)
Response delay time
tPHL (tPLH)
20 s typ.
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 3)
Emitter
Detector
Peak spectral sensitivi- P
ty wavelength
LED current when output is OFF
LED current when output is ON
148
EE-SX3096-W11/4096-W11 Photomicrosensor (Transmissive)
Note: 1. Hysteresis denotes the difference in
forward LED current value, expressed in percentage,
calculated from the respective forward LED currents
when the photo IC in turned from ON to OFF and
when the photo IC in turned from OFF to ON.
3. The following illustrations show the definition of response
delay time. The value in the parentheses applies to the
EE-SX4096.
Input
2. The value of the response frequency is
measured by rotating the disk as shown below.
Output
2.1 mm
0.5 mm
Input
Output
EE-SX3096
EE-SX4096
Disk
0.5 mm
■ Engineering Data
Note: The values in the parentheses apply to the EE-SX4096.
IFT OFF (IFT ON)
IFT ON (IFT OFF)
LED current IFT (mA)
Forward current IF (mA)
Low-level Output Voltage vs.
Output Current (Typical)
IFT ON (IFT OFF)
Supply voltage VCC (V)
Low-level Output Voltage vs.
Ambient Temperature Characteristics (Typical)
Ta = 25°C
VCC = 5 V
IF = 0 mA (15 mA)
Response Delay Time vs. Forward
Current (Typical)
Response delay time tPHL, tPLH (μs)
Current consumption Icc (mA)
IFT OFF (IFT ON)
VCC = 5 V
IF = 0 mA (15 mA)
IOL = 16 mA
IOL = 5 mA
Ambient temperature Ta (°C)
Output current IC (mA)
Current Consumption vs. Supply
Voltage (Typical)
Supply voltage VCC (V)
Ta = 70°C
Forward voltage VF (V)
Ambient temperature Ta (°C)
Ta = 25°C
IF = 0 mA (15 mA)
Ta = 25°C
RL = 1 kΩ
Low level output voltage VOL (V)
LED current IFT (mA)
VCC = 5 V
RL = 330 Ω
LED Current vs. Supply Voltage
(Typical)
Ta = −30°C
Ta = 25°C
Low level output voltage VOL (V)
LED Current vs. Ambient Temperature Characteristics (Typical)
Forward Current vs. Forward
Voltage Characteristics (Typical)
VCC = 5 V
RL = 330 Ω
Ta = 25°C
VOUT
(EE-SX3@@)
VOUT
(EE-SX4@@)
Repeat Sensing Position
Characteristics (Typical)
Output transistor
Ambient temperature Ta (°C)
Output allowable dissipation PC (mW)
Forward current IF (mA)
Forward Current vs. Collector
Dissipation Temperature Rating
Ta = 25°C
IF = 15 mA
VCC = 5 V
RL = 330 Ω
n = repeat 20 times
ON
(OFF)
d1 = 0.01 mm
Center of optical axis
d
OFF
(ON)
-0.4 -0.3 -0.2 -0.1
Forward current IF (mA)
0
0.1
0.2
0.3
0.4
0.5
0.6
Distance d (mm)
EE-SX3096-W11/4096-W11 Photomicrosensor (Transmissive)
149