LOW POWER PROGRAMMABLE OSCILLATOR SERIES „LPOP“

PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
LOW POWER OSCILLATOR 1.0—110.0 MHz
SERIES „LPO“
FEATURES
APPLICATIONS
+
+
+
+
+
Low Power Oscillator for Low Cost
Excellent long time reliability
Very tight frequency stability as low as ±20 ppm over –40/+85°C
Outstanding long term aging
Programmable drive strength for improved jitter, system EMI
+ Ideal for DSC, DVC, DVR, IP CAM, Tablets, e-Books, SSD, GPON,
+
+
+
+
reduction, or driving large capacitive loads
LVCMOS/HCMOS compatible output
Industry-standard packages: 2.0x1.6; 2.5x2.0; 3.2x2.5; 5.0x3.2; 7.0x5.0
Express samples within 1 day ex works PETERMANN-TECHNIK
Pb-free, RoHS and REACH compliant / MSL1@260°C
EPON, Embedded, Consumer, Medical, Telecom, Industrial, etc.
+ Ideal for high-speed serial protocols such as: USB, SATA, SAS,
Firewire, 100M / 1G / 10G Ethernet, etc.
GENERAL DATA[1]
PARAMETER AND CONDITIONS
SYMBOL
MIN.
TYP.
MAX.
UNIT
CONDITION
f
1
–
110
MHz
F_stab
-20
–
+20
PPM
Inclusive of initial tolerance at 25°C, 1st year aging at 25°C,
-25
–
+25
PPM
and variations over operating temperature, rated power
-50
–
+50
PPM
supply voltage and load (15 pF ± 10%).
-20
–
+70
°C
Commercial
FREQUENCY RANGE
Output Frequency Range
FREQUENCY STABILITY AND AGING
Frequency Stability
OPERATING TEMPERATURE RANGE
Operating Temperature Range
T_use
-40
–
+85
°C
Industrial
Storage Temperature Range
T_stor
-55
–
+125
°C
Storage
VDD
1.62
1.8
1.98
V
Contact Petermann-Technik for 1.5V support
2.25
2.5
2.75
V
2.52
2.8
3.08
V
SUPPLY VOLTAGE AND CURRENT CONSUMPTION
Supply Voltage
Current Consumption
OE Disable Current
Standby Current
2.7
3.0
3.3
V
2.97
3.3
3.63
V
2.25
–
3.63
V
IDD
–
3.8
4.5
mA
No load condition, f = 20 MHz, VDD= 2.8V, 3.0V, 3.3V, 2.25V to 3.63V
IDD
–
3.6
4.2
mA
No load condition, f = 20 MHz, VDD = 2.5V
IDD
–
3.4
3.9
mA
No load condition, f = 20 MHz, VDD = 1.8V
I_OD
–
–
4
mA
VDD = 2.5V to 3.3V, OE = GND, output is pulled down
–
–
3.8
mA
VDD = 1.8V, OE = GND, output is pulled down
–
2.6
4.3
µA
ST = GND, VDD = 2.8V to 3.3V, output is pulled down
–
1.4
2.5
µA
ST = GND, VDD= 2.5V, output is pulled down
–
0.6
1.3
µA
ST = GND, VDD = 1.8V, output is pulled down
I_std
Note: 1. All electrical specifications in the above table are specified with 15 pF output load at default drive strength and for all VDD(s) unless otherwise stated.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 1 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
GENERAL DATA[1] (continued)
PARAMETER AND CONDITIONS
SYMBOL
MIN.
TYP.
MAX.
UNIT
DC
45
–
55
%
All VDDs
Tr, Tf
–
1
2
ns
VDD = 2.5V, 2.8V, 3.0V or 3.3V, 20% - 80%
–
1.3
2.5
ns
VDD =1.8V, 20% - 80%
–
–
2
ns
VDD = 2.25V - 3.63V, 20% - 80%
CONDITION
LVCMOS OUTPUT CHARACTERISTICS
Duty Cycle
Rise/Fall Time
Output High Voltage
VOH
90%
–
–
VDD
IOH = -4 mA (VDD = 3.0V or 3.3V)
IOH = -3 mA (VDD = 2.8V and VDD= 2.5V)
IOH = -2 mA (VDD= 1.8V)
Output Low Voltage
VOL
–
–
10%
VDD
IOL = 4 mA (VDD = 3.0V or 3.3V)
IOL = 3 mA (VDD= 2.8V and VDD = 2.5V)
IOL = 2 mA (VDD = 1.8V)
VIH
70%
–
–
VDD
Pin 1, OE or ST
Input Low Voltage
VIL
–
–
30%
VDD
Pin 1, OE or ST
Input Pull-up Impedence
Z_in
–
87
100
kΩ
Pin 1, OE logic high or logic low, or ST logic high
2
–
–
MΩ
Pin 1, ST logic low
T_start
–
–
5
ms
Measured from the time VDD reaches its rated minimum value
T_oe
–
–
130
ns
f = 110 MHz. For other frequencies, T_oe = 100 ns + 3* cycles
T_resume
–
–
5
ms
Measured from the time ST pin crosses 50% threshold
RMS Period Jitter
T_jitt
–
1.76
3
ps
f = 75 MHz, VDD = 2.5V, 2.8V, 3.0V or 3.3V
T_jitt
–
1.78
3
ps
f = 75 MHz, VDD = 1.8V
RMS Phase Jitter (random)
T_phj
–
0.5
0.9
ps
f = 75 MHz, Integration bandwidth = 900 kHz to 7.5 MHz
T_phj
–
1.3
2
ps
f = 75 MHz, Integration bandwidth = 12 kHz to 20 MHz
INPUT CHARACTERISTICS
Input High Voltage
STARTUP AND RESUME TIMING
Startup Time
Enable/Disable Time
Resume Time
JITTER
EXCELLENT RELIABILITY DATA
MTBF
500 million hours
Shock Resistance:
10.000 G
Vibration Resistance:
70 g
Note: 1. All electrical specifications in the above table are specified with 15 pF output load and for all V DD(s) unless otherwise stated.
PIN DESCRIPTION
PIN
1
SYMBOL
OE/ ST/NC
TOP VIEW
FUNCTIONALITY
Output Enable
H or Open[2]: specified frequency output
L: output is high impedance. Only output driver is disabled.
Standby
H or Open[2]: specified frequency output
L: output is low (weak pull down). Device goes to sleep mode.
Supply current reduces to I_std.
No Connect
Any voltage between 0 and VDD or Open
quency output. Pin 1 has no function.
2
GND
Power
Electrical ground[3]
3
OUT
Output
Oscillator output
4
VDD
Power
Power supply voltage[3]
[2]:
OE/ST/NC
1
4
VDD
GND
2
3
OUT
: Specified fre-
Note: 2. In OE or ST mode, a pull-up resistor of 10kΩ or less is recommended if pin 1 is not externally driven. If pin 1 needs to be left floating, use the NC option.
3. A capacitor value of 0.1 µF between V DD and GND is recommended.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 2 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
TEST CIRCUIT AND WAVEFORM
FIGURE 1. TEST CIRCUIT
FIGURE 2. WAVEFORM
Vout
VDD
3
4
Power
Supply
Test
Point
tf
80%VDD
0.1µF
15pF
(including
probe
and fixture
capacitance)
2
1
tr
50%
20%VDD
High Pulse
(TH)
Low Pulse
(TL)
Period
VDD
OE/ST Function
1kΩ
TIMING DIAGRAMS(4)
FIGURE 3. STARTUP TIMING (OE/ST MODE)
90%VDD, 2.5/2.8/3.3V devices
95%VDD, 1.8V devices
VDD
Pin 4 Voltage
FIGURE 4. STANDBY RESUME TIMING (ST MODE ONLY)
50%VDD
No Glitch first cycle
VDD
ST Voltage
T_resume
T_start
CLK Output
T_start: Time to start from power-off
FIGURE 5. OE ENABLE TIMING (OE MODE ONLY)
CLK Output
T_resume: Time to resume from ST
FIGURE 6. OE DISABLE TIMING (OE MODE ONLY)
VDD
50%VDD
VDD
OE Voltage
OE Voltage
50%VDD
T_OE
CLK Output
CLK Output
T_OE
HZ
T_OE: Time to re-enable the clock output
T_OE: Time to put the output drive in High Z mode
Note: 4. LPO supports no runt pulses and no glitches during startup or resume.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 3 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
PERFORMANCE PLOTS(5)
FIGURE 7. IDD vs. FREQUENCY
FIGURE 8. RMS PERIOD JITTER vs. FREQUENCY
6.0
4.0
3.5
RMS period jitter (ps)
5.5
IDD (mA)
5.0
4.5
4.0
3.0
2.5
2.0
1.5
1.0
3.5
3.0
0.5
0
10
20
30
40
50
60
70
80
90
0.0
100 110
0
10
20
30
1.8
2.5
2.8
3.0
40
50
60
70
80
90
100 110
Frequency (MHz)
Frequency (MHz)
3.3
1.8
FIGURE 9. RMS PHASE JITTER vs. FREQUENCY
(12 kHz TO 20 MHZ INTEGRATION BANDWIDTH)
2.5
2.8
3.0
3.3
FIGURE 10. RMS PHASE JITTER vs. FREQUENCY
(900 kHz TO 20 MHZ INTEGRATION BANDWIDTH)
2.0
0.9
0.85
1.8
0.8
1.6
IPJ (ps)
IPJ (ps)
0.75
1.4
0.7
0.65
0.6
0.55
1.2
0.5
0.45
1.0
0
30
50
70
90
0.4
110
0
30
50
Frequency (MHz)
1.8
2.5
2.8
3.0
70
90
110
Frequency (MHz)
3.3
1.8
FIGURE 11. DUTY CYCLE vs. FREQUENCY
2.5
2.8
3.0
3.3
FIGURE 12. RISE TIME vs. TEMPERATURE, 20 MHZ OUTPUT
2.5
55
54
2.0
Rise Time (ns)
Duty Cycle (%)
53
52
51
50
49
48
47
1.5
1.0
0.5
46
45
0
10
20
30
40
50
60
70
80
90
100 110
0.0
-40
-15
10
Frequency (MHz)
1.8
2.5
2.8
3.0
35
60
85
Temperature (°C)
3.3
1.8
2.5
2.8
3.0
3.3
Note: 5. All plots are measured with 15 pF load at room temperature, unless otherwise stated.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 4 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
PROGRAMMABLE DRIVE STRENGTH
The LPO includes a programmable drive strength feature named SoftLevel to provide a simple, flexible tool to optimize the clock rise/fall
time for specific applications. Benefits from the programmable drive
strength feature are:
HIGH OUTPUT LOAD CAPABILITY
The rise/fall time of the input clock varies as a function of the actual
capacitive load the clock drives. At any given drive strength, the rise/
fall time becomes slower as the output load increases. As an examp-
+ Improves system radiated electromagnetic interference (EMI) by
le, for a 3.3V LPO device with default drive strength setting, the typical rise/fall time is 1ns for 15 pF output load. The typical rise/fall
slowing down the clock rise/fall time
+ Improves the downstream clock receiver’s (RX) jitter by decreasing (speeding up) the clock rise/fall time.
time slows down to 2.6 ns when the output load increases to 45 pF.
One can choose to speed up the rise/fall time to 1.68 ns by then increasing the drive strength setting on the LPO.
+ Ability to drive large capacitive loads while maintaining full swing
with sharp edge rates.
The LPO can support up to 60 pF or higher in maximum capacitive
loads with up to 3 additional drive strength settings. Refer to the
For more detailed information about rise/fall time control and drive
strength selection, see the Petermann-Technik Applications Note
Rise/Tall Time Tables to determine the proper drive strength for
the desired combination of output load vs. rise/fall time.
section: http://www.petermann-technik.com
EMI REDUCTION BY SLOWING RISE/FALL TIME (SoftLevel FUNCTION)
LPO DRIVE STRENGTH SELECTION
Figure 13 shows the harmonic power reduction as the rise/fall times
Tables 1 through 5 define the rise/fall time for a given capacitive load
are increased (slowed down). The rise/fall times are expressed as a
and supply voltage.
ratio of the clock period. For the ratio of 0.05, the signal is very close
to a square wave. For the ratio of 0.45, the rise/fall times are very
close to near-triangular waveform. These results, for example, show
that the 11th clock harmonic can be reduced by 35 dB if the rise/fall
edge is increased from 5% of the period to 45% of the period.
10
Select the capacitive load column that matches the application requirement (5 pF to 60 pF)
Under the capacitive load column, select the desired
rise/fall times.
4.
The left-most column represents the part number code for
the corresponding drive strength.
5.
0
Select the table that matches the LPO nominal supply voltage (1.8V, 2.5V, 2.8V, 3.0V, 3.3V).
2.
3.
FIGURE 13. HARMONIC EMI REDUCTION AS A FUNCTION OF
SLOWER RISE/FALL TIME (SoftLevel FUNCTION)
Harmonic amplitude (dB)
1.
Add the drive strength code to the part number for
ordering purposes.
-10
-20
CALCULATING MAXIMUM FREQUENCY
-30
Based on the rise and fall time data given in Tables 1 through 5, the
-40
maximum frequency the oscillator can operate with guaranteed
-50
full swing of the output voltage over temperature as follows:
-60
Max. frequency =
-70
-80
1
3
trise=0.05
5
7
9
Harmonic number
trise=0.1
trise=3.0
trise=0.15
trise=0.35
trise=0.2
trise=0.4
11
trise=0.25
trise=0.45
JITTER REDUCTION WITH FASTER RISE/FALL TIME
Power supply noise can be a source of jitter for the downstream chipset. One way to reduce this jitter is to increase rise/fall time (edge
rate) of the input clock. Some chipsets would require faster rise/fall
time in order to reduce their sensitivity to this type of jitter. The LPO
1
6 x (Trise)
EXAMPLE 1
Calculate fMAX for the following condition:
+ VDD = 1.8V (Table 1)
+ Capacitive Load: 30pF
+ Desired Tr/tf time = 3ns (rise/fall time part number code=E)
Part number for the above example:
LPO18-2520-E-25-M-25.000MHz-T-E
provides up to 3 additional high drive strength settings for very fast
rise/fall time. Refer to the rise/fall time tables to determine the proper drive strength.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
Drive strength code is inserted here. Standard setting is “S”
PAGE 5 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
RISE/FALL TIME (20% TO 80%) vs CLOAD
TABLE 1. VDD = 1.8V RISE/FALL TIMES FOR SPECIFIC CLOAD
TABLE 2. VDD = 2.5V RISE/FALL TIMES FOR SPECIFIC CLOAD
RISE/FALL TIME TYP (NS)
Drive Strength \ CLOAD
RISE/FALL TIME TYP (NS)
5 pF
15 pF
30 pF
45 pF
60 pF
L
6.16
11.61
22.00
31.27
39.91
Drive Strength \ CLOAD
5 pF
15 pF
30 pF
45 pF
60 pF
L
4.13
8.25
12.82
21.45
27.79
A
3.19
6.35
11.00
16.01
21.52
A
2.11
4.27
7.64
11.20
14.49
R
2.11
4.31
7.65
10.77
14.47
R
1.45
2.81
5.16
7.65
9.88
B
1.65
3.23
5.79
8.18
11.08
B
1.09
2.20
3.88
5.86
7.57
T
0.93
1.91
3.32
4.66
6.48
T
0.62
1.28
2.27
3.51
4.45
E
0.78
1.66
2.94
4.09
5.74
S = standard limit
0.54
1.00
2.01
3.10
4.01
U
0.70
1.48
2.64
3.68
5.09
U
0.43
0.96
1.81
2.79
3.65
S = standard limit
0.65
1.30
2.40
3.35
4.56
F
0.34
0.88
1.64
2.54
3.32
TABLE 3. VDD = 2.8V RISE/FALL TIMES FOR SPECIFIC CLOAD
TABLE 4. VDD = 3.0V RISE/FALL TIMES FOR SPECIFIC CLOAD
RISE/FALL TIME TYP (NS)
Drive Strength \ CLOAD
5 pF
15 pF
L
3.77
7.54
30 pF
RISE/FALL TIME TYP (NS)
45 pF
60 pF
12.28
19.57
25.27
Drive Strength \ CLOAD
5 pF
15 pF
30 pF
45 pF
60 pF
L
3.60
7.21
11.97
18.74
24.30
A
1.94
3.90
7.03
10.24
13.34
A
1.84
3.71
6.72
9.86
12.68
R
1.29
2.57
4.72
7.01
9.06
R
1.22
2.46
4.54
6.76
8.62
B
0.97
2.00
3.54
5.43
6.93
B
0.89
1.92
3.39
5.20
6.64
T
0.55
1.12
2.08
3.22
4.08
S = standard limit
0.51
1.00
1.97
3.07
3.90
S = standard limit
0.44
1.00
1.83
2.82
3.67
E
0.38
0.92
1.72
2.71
3.51
U
0.34
0.88
1.64
2.52
3.30
U
0.30
0.83
1.55
2.40
3.13
F
0.29
0.81
1.48
2.29
2.99
F
0.27
0.76
1.39
2.16
2.85
TABLE 5. VDD = 3.3V RISE/FALL TIMES FOR SPECIFIC CLOAD
RISE/FALL TIME TYP (NS)
Drive Strength \ CLOAD
5 pF
15 pF
30 pF
45 pF
L
3.39
6.88
11.63
17.56
60 pF
23.59
A
1.74
3.50
6.38
8.98
12.19
R
1.16
2.33
4.29
6.04
8.34
B
0.81
1.82
3.22
4.52
6.33
ST =
orstandard
"-": standard
limit
0.46
1.00
1.86
2.60
3.84
E
0.33
0.87
1.64
2.30
3.35
U
0.28
0.79
1.46
2.05
2.93
F
0.25
0.72
1.31
1.83
2.61
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 6 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
DIMENSIONS AND PATTERNS
RECOMMENDED LAND PATTERN (UNIT:MM) [6]
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
2.0 X 1.6 X 0.75 MM
#1
1.5
0.65
#3
#3
#1
#2
#2
0.8
1.2
0.93
#4
0.48
2.0±0.05
1.6±0.05
#4
0.9
0.75±0.05
0.68
RECOMMENDED LAND PATTERN (UNIT:MM)
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
2.5 X 2.0 X 0.75 MM
#1
1.9
1.00
#3
#3
#1
#2
#2
1.0
1.1
1.5
#4
0.5
2.5±0.05
2.0±0.05
#4
1.1
0.75±0.05
0.75
RECOMMENDED LAND PATTERN (UNIT:MM)
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
3.2 X 2.5 X 0.75 MM
#3
#1
#2
#2
1.2
0.9
1.9
#4
0.9
1.4
0.75±0.05
#1
2.2
2.1
#3
0.7
3.2±0.05
2.5±0.05
#4
Note: 6. A capacitor value of 0.1 µF between VDD and GND is recommended (see note 2 + 3).
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 7 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
DIMENSIONS AND PATTERNS
RECOMMENDED LAND PATTERN (UNIT:MM) [7]
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
5.0 X 3.2 X 0.75 MM
#1
2.54
2.39
#3
#3
#1
#2
#2
1.6
0.8
2.2
#4
1.1
5.0±0.05
3.2±0.05
#4
1.5
0.75±0.05
1.15
RECOMMENDED LAND PATTERN (UNIT:MM)
PACKAGE SIZE – DIMENSIONS (UNIT:MM)
7.0 X 5.0 X 0.90 MM
#3
#1
#2
3.81
#4
#2
2.0
1.1
1.4
2.2
0.90±0.10
#1
5.08
5.08
#3
2.6
7.0±0.05
5.0±0.05
#4
REFLOW SOLDER PROFILE
Note: 7. A capacitor value of 0.1 µF between VDD and GND is recommended (see note 2 + 3).
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 8 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
ORDERING INFORMATION
OSCILLATOR
FAMILY
LPO
SUPPLY VOLTAGE
“18“ for 1.8V
“25“ for 2.5V
“28“ for 2.8V
“3“ for 3.0V
“33“ for 3.3V
“XX“ for 2.25V to 3.63V
TEMPERATURE
RANGE
“C” for 0 +70°C
“D” for -10 +70°C
“M” for -20 +70°C
“W” for -40 +85°C
FREQUENCY
1.000000 to
110.000000 MHz
LPO 33-2520-E-25-M-25.000MHz-T-S
FREQUENCY
STABILITY
“20” for ±20 PPM
“25” for ±25 PPM
“50” for ±50 PPM
PACKAGE SIZE
“2016” for 2.0 X 1.6 mm
“2520” for 2.5 X 2.0 mm
“3225” for 3.2 X 2.5 mm
“5032” for 5.0 X 3.2 mm
“7050” for 7.0 X 5.0 mm
PACKING METHOD
“B” for BULKS or TUBES
“T” for TAPE & REEL
OUTPUT DRIVE
STRENGTH
FEATURE PIN 1
“E” for OUTPUT ENABLE
“S” for STANDBY
“N” for NO CONNECT
“S” Standard (datasheet
limits) See Tables 1 to 5
for rise/fall times
“L”
“T”
“A”
“E”
“R”
“U”
“B”
“F”
EXAMPLE: LPO33-2520-E-25-M-25.000MHz-T-S
PLEASE INDICATE YOUR REQUIRED PARAMETERS
EXPRESS SAMPLES ARE DELIVERABLE ON THE SAME DAY
IF ORDERED UNTIL 02:00 PM!
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 9 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014
PETERMANN-TECHNIK GmbH
Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech
Tel: +49/8191/305395 ∙ Fax: +49/8191/305397
[email protected] ∙ www.petermann-technik.com
PREMIUM QUALITY BY
PETERMANN-TECHNIK
OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH.
THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY
MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS.
© PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns
all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or
services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited.
CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS
PAGE 10 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014