PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com LOW POWER TCXO & VCTCXO OSCILLATOR SERIES „TCVCTO-1“ 1.0—80.0 MHz FEATURES APPLICATIONS + + + + + + + + + + + WiFi, 3G, LTE, SDI, Ethernet, SONET, DSL + Telecom, networking, smart meter, wireless, test instrumentation + etc. 100% pin-to-pin drop-in replacement to quartz and MEMS based VCTCXO Ultra Performance Oscillator for Low Cost TCXO function active when Pin 1 = not connected Wide tuning range up to ±50 ppm Excellent long time reliability—outperforms quartz-based XO Frequency stability as low as ±1.5 ppm (±0.5 and ±1 ppm optionally) Outstanding long term aging LVCMOS compatible output with option for EMI reduction Packages available 2.5x2.0; 3.2x2.5; 5.0x3.2; 7.0x5.0 mm Pb-free, RoHS and REACH compliant / MSL1@260°C GENERAL DATA PARAMETER AND CONDITIONS Output Frequency Range SYMBOL MIN. TYP. MAX. UNIT f 1 – 80 MHz CONDITION Initial Tolerance F_init -1 – 1 PPM At 25°C Stability Over Temperature F_stab -1.5 – +1.5 PPM -2 – +2 PPM -2.5 – +2.5 PPM -5 – +5 PPM Over operating temperature range at rated nominal power supply voltage and load (see ordering codes on page 7) ±1.5 ppm is available in -20 to 70 °C temp. range only. Contact PETERMANN-TECHNIK for ±0.5ppm and±1 ppm options. Supply Voltage F_VDD – 50 – PPB ±10% VDD (±5% for VDD = 1.8V) Output Load F_load – 0.1 – PPM 15 pF ±10% of load First year Aging F_aging -1.5 – +1.5 PPM 25°C -3.5 – +3.5 PPM 25°C 10-year Aging Stability vs. Temperature Slope F_slope – 0.1 – PPM/°C Operating Temperature Range T_use -20 – +70 °C Extended Commercial -40 – +85 °C Industrial T_stor -65 – +150 VDD 1.71 1.8 1.89 V 2.25 2.5 2.75 V Contact PETERMANN-TECHNIK for any other supply voltage option. 2.52 2.8 3.08 V 2.70 3.0 3.3 V 2.97 3.3 3.63 Storage Temperature Range Supply Voltage Pull Range PR ±12.5, ±25, ±50 V PPM Upper Control Voltage VC_U VDD-0.1 – – V Control Voltage Range VC_L – – 0.1 V Control Voltage Input Impedance Z_vc 100 – – kΩ Frequency Change Polarity Control Voltage -3dB Bandwidth Current Consumption OE Disable Current Standby Current – positive slope All VDDs. Voltage at which maximum deviation is guaranteed. – V_BW – – 8 kHz IDD – 31 33 mA No load condition, f = 20 MHz, VDD = 2.5V, 2.8V or 3.3V. – 29 31 mA No load condition, f = 20 MHz, VDD = 1.8V. – – 31 mA VDD = 2.5V, 2.8V or 3.3V, OE = GND, output is pulled down – – 30 mA VDD = 1.8 V. OE = GND, output is pulled down – – 70 µA VDD = 2.5V, 2.8V or 3.3V, ST = GND, output is pulled down. – – 10 µA VDD = 1.8V. ST = GND, output is pulled down. I_OD I_std Note: 1. All electrical specifications in the above table are specified with 15 pF output load at default drive strength and for all VDD(s) unless otherwise stated. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 1 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com GENERAL DATA (continued) PARAMETER AND CONDITIONS Duty Cycle LVCMOS Rise/Fall Time SYMBOL MIN. TYP. MAX. UNIT DC 45 – 55 % All VDDs Tr, Tf – 1.5 2 ns LVCMOS option. Default rise/fall time, All VDDs, 10% - 90% VDD. ns EMI reduction option. Frequency and supply voltage dependent. OH = -7 mA, IOL = 7 mA, (VDD = 3.3V, 3.0V) IOH = -4 mA,IOL = 4 mA, (VDD = 2.8V, 2.5V) IOH = -2 mA, IOL = 2 mA, (VDD = 1.8V) EMI reduction Rise/Fall Time EMI reduction Rise/Fall Time Table Output Voltage High VOH Output Voltage Low Input Voltage High CONDITION 90% – – VDD VOL – – 10% VDD VIH 70% – – VDD Pin 1, OE or ST Input Voltage Low VIL – – 30% VDD Pin 1, OE or ST Input Pull-up Impedance Z_in – 100 250 kΩ T_start – – 10 ms Measured from the time VDD reaches its rated minimum value Startup Time OE Enable/Disable Time Resume Time RMS Period Jitter RMS Phase Jitter (random) T_oe – – 150 ns f = 80 MHz. For other frequencies, T_oe = 100 ns + 3 cycles T_resume – 6 10 ms Measured from the time ST pin crosses 50% threshold T_jitt – 1.7 2 ps f = 10 MHz, VDD = 2.5V, 2.8V or 3.3V – 1.7 2 ps f = 10 MHz, VDD = 1.8V – 0.5 1 ps f = 10 MHz, Integration bandwidth = 12 kHz to 20 MHz, All VDDs T_phj Note: 1. All electrical specifications in the above table are specified with 15 pF output load and for all VDD(s) unless otherwise stated. PIN DESCRIPTION PIN SYMBOL FUNCTIONALITY V control Output Enable 1 TOP VIEW VC/OE/ST/NC Standby NC Voltage control H or Open[2]: specified frequency output L: output is high impedance. Only output driver is disabled. H or Open[2]: specified frequency output L: output is low (weak pull down). Device goes to sleep mode. Supply current reduces to I_std. VC/OE/ST/NC 1 4 VDD GND 2 3 OUT No connect (input receiver off) 2 GND Power Electrical and case ground 3 CLK Output Oscillator output 4 VDD Input Power Power supply voltage Note: 2. A pull-up resistor of <10 kΩ between OE/ ST pin and VDD is recommended in high noise environment when the device operates in OE/ST mode. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 2 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TIMING DIAGRAMS ST/OE MODE ST MODE ONLY 90%VDD, 2.5/2.8/3.3V devices 95%VDD, 1.8V devices VDD 50%VDD Pin 4 Voltage VDD ST Voltage T_resume T_start CLK Output CLK Output T_start: Time to start from power-off T_resume: Time to resume from ST PHASE NOISE PLOT PHASE NOISE, 10MHZ CARRIER, 3.3V, LVCMOS OUTPUT, TCXO -100 -110 Integrated random phase jitter (RMS, 12kHz-5MHz): 0.52ps Phase Noise (dBc/Hz) -120 -130 -140 -150 -160 -170 103 104 105 Frequency Offset (Hz) CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS 106 PAGE 3 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com EMI REDUCTION OPTION The adjustable output is available as a standard option for the TCVCTO-1 (TCXO & VCTCXO). The adjustable EMI reduction option is used typically for EMI reduction similar to that of a clipped sinewave output common to many quartz based TCXOs. In the EMI reduction mode, the slower rise/fall edges of the output waveform reduce the higher clock harmonics in a digital clock signal, minimizing EMI radiation at these harmonics. The table below show the actual rise/fall time in relation to the desired output frequency and the supply voltage with a 10 kΩ / 10pF load. Rail-to-rail swing of the output is maintained for these supported frequencies. PARAMETER SYMBOL Rise/Fall Time Tr, Tf MIN. TYP. MAX. UNIT 4.0 6.5 9.5 ns CONDITION 1-26MHz, 1.8V, 3.0 and 3.3V, MHz 10k and 10 pF, 20%-80% VDD 2.5 4.0 6.0 ns 1-26MHz, 2.5V and 2.8V, MHz 10k and 10 pF, 20%-80% VDD 1.5 3.5 5.0 ns 26-40MHz, 1.8V, 3.0V and 3.3V, MHz 10k and 10 pF, 20%80% VDD 1.5 2.5 4.5 ns 26-40 MHz, 2.5V and 2.8V, MHz 10k and 10 pF, 20%-80% VDD EMI REDUCTION WAVEFORM EXAMPLES AND CORRESPONDING HARMONICS REDUCTION Figures below illustrate the harmonic power reduction as the rise/fall times are slowed from the standard squarewave output to that of the EMI reduction output. In general, the 1.8V device shows the lowest harmonics and provides best EMI performance comparing to devices with higher operating voltages. Odd Harmonic Power and EMI reduction Outputs, VDD = 3.3V 3.5 for LVCMOS and EMI reduction Outputs, VDD = EMI reduction EMI reduction 3 Harmonic Power (dbm) 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 Harmonic Number Time Odd Harmonic Power and EMI reduction Outputs, VDD = 2.5V for LVCMOS and EMI reduction Outputs, VDD = EMI reduction Amplitude ( 0.5V/Div Harmonic Power (dbm) EMI reduction Time ( 20ns/Div Harmonic Number and EMI reduction Outputs, VDD = 1.8V Odd Harmonic Power for LVCMOS and EMI reduction Outputs, VDD = EMI reduction EMI reduction Harmonic Power (dbm) Amplitude ( 0.5V/Div Amplitude 2.5 Harmonic Number Time ( 20ns/Div CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 4 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [3] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 2.7X 2.4 X 0.75 MM (100% compatible with 2.5 x 2. 0 mm footprint) #1 1.9 1.00 #3 #3 #1 #2 #2 1.0 1.5 1.25 #4 0.5 2.7±0.05 2.4±0.05 #4 1.1 0.75±0.05 0.9 RECOMMENDED LAND PATTERN (UNIT:MM) [3] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 3.2 X 2.5 X 0.75 MM #1 2.2 2.1 #3 #3 #1 #2 #2 1.2 1.9 0.9 #4 0.7 3.2±0.05 2.5±0.05 #4 1.4 0.75±0.05 0.9 RECOMMENDED LAND PATTERN (UNIT:MM) [3] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0X 3.2 X 0.75 MM #3 # #2 #2 1.60 0.8 2.20 #4 1.15 0.75±0.05 #1 2.54 2.39 #3 1.1 5.0±0.05 3.2±0.05 #4 1.50 Note: 3. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 5 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [3] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0X 5.0 X 0.90 MM #3 #1 #2 3.81 #4 #2 0.90±0.10 #1 5.08 5.08 #3 1.40 2.0 1.10 2.6 7.0±0.05 5.0±0.05 #4 2.2 REFLOW SOLDER PROFILE Note: 3. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 6 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION FREQUENCY 1.000000 to 80.000000 MHz OSCILLATOR FAMILY TCVCTO-1 OUTPUT WAVEFORM “S“ Standard limits “C” EMI reduction Option TEMPERATURE RANGE SUPPLY VOLTAGE “18“ for 1.8V “25“ for 2.5V “28“ for 2.8V “30“ for 3.0V “33“ for 3.3V “M” for -20 +70°C “W” for -40 +85°C TCVCTO133-2724-E0-2.5-M-19.200MHz-T-S “2724” for 2.7 X 2.4 mm “3225” for 3.2 X 2.5 mm “5032” for 5.0 X 3.2 mm “7050” for 7.0 X 5.0 mm PACKING METHOD FREQUENCY STABILITY PACKAGE SIZE “B” for Bulks or Tubes “T” for Tape & Reel “1.5” for ±1.5 PPM “2.0” for ±2.0 PPM “2.5” for ±2.5 PPM “5.0” for ±5.0 PPM SEE TABLE BELOW OPTIONS PIN 1 “V” for VOLTAGE CONTROL “E” for OUTPUT ENABLE “S” for STANDBY “N” for NO CONNECT “O” for FIXED FREQUENCY PULL RANGE OPTIONS (PIN1 = “V” OPTION ONLY) “VQ” for ±12.5 PPM “VM” for ±25 PPM “VB” for ±50 PPM EXAMPLE: TCVCTO133-2724-E0-2.5-M-19.200MHz-T-S PLEASE INDICATE YOUR REQUIRED PARAMETERS Frequency Stability (PPM) Temperature Range FREQUENCY STABILITY (PPM) TEMPERATURE RANGE M (-20 to +70°C) W (-40 to +85°C) ±5 ±2.5 ±2 ±1.5 Contact PETERMANN-TECHNIK ±1 Contact PETERMANN-TECHNIK Contact PETERMANN-TECHNIK ±0.5 Contact PETERMANN-TECHNIK Contact PETERMANN-TECHNIK SAMPLES ARE AVAILABLE WITHIN A SHORT DELIVERY PERIOD! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 7 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 8 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014