PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com LOW POWER PROGRAMMABLE OSCILLATOR SERIES „LPOP“ 115.0—137.0 MHz FEATURES APPLICATIONS + + + + + + High Frequency Programmable Low Power Oscillator for Low Cost Excellent long time reliability Excellent total frequency stability as low as ±20 ppm over –40/+85°C Excellent long term aging Low power consumption of 4.8 mA typical Programmable drive strength for improved jitter, system EMI + Ideal for GPON/GPON, network switches, routers. servers, + + + + reduction, or driving large capacitive loads LVCMOS/HCMOS compatible output Industry-standard packages: 2.0x1.6; 2.5x2.0; 3.2x2.5; 5.0x3.2; 7.0x5.0 Express samples within 1 day ex works Pb-free, RoHS and REACH compliant / MSL1@260°C embedded systems, Telecom, Medical, Industrial, Consumer, etc. + Ideal for Ethernet, PCI-E, DDR, USB, SATA, Storage server, etc. GENERAL DATA[1] PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT CONDITION f 115 – 137 MHz F_stab -20 – +20 PPM Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, -25 – +25 PPM and variations over operating temperature, rated power -50 – +50 PPM supply voltage and load. -20 – +70 °C Extended Commercial -40 – +85 °C Industrial -55 – +125 °C Storage 1.62 1.8 1.98 V Contact Petermann-Technik for 1.5V support 2.25 2.5 2.75 V 2.52 2.8 3.08 V FREQUENCY RANGE Output Frequency Range FREQUENCY STABILITY AND AGING Frequency Stability OPERATING TEMPERATURE RANGE Operating Temperature Range T_use Storage Temperature Range T_stor SUPPLY VOLTAGE AND CURRENT CONSUMPTION Supply Voltage VDD 2.7 3.0 3.3 V 2.97 3.3 3.63 V 2.25 – 3.63 V IDD – 6.2 7.5 mA No load condition, f = 125 MHz, VDD= 2.8V, 3.0V, 3.3V, or 2.25V to 3.63V IDD – 5.4 6.4 mA No load condition, f = 125 MHz, VDD = 2.5V IDD – 4.8 5.6 mA No load condition, f = 125 MHz, VDD = 1.8V OE Disable Current I_OD – – 4 mA VDD = 2.5V to 3.3V, OE = GND, output is pulled down – – 3.8 mA VDD = 1.8V, OE = GND, output is pulled down Standby Current I_std – 2.6 4.3 µA ST = GND, VDD = 2.8V to 3.3V, output is pulled down – 1.4 2.5 µA ST = GND, VDD= 2.5V, output is pulled down – 0.6 1.3 µA ST = GND, VDD = 1.8V, output is pulled down Current Consumption Note: 1. All electrical specifications in the above table are specified with 15 pF output load at default drive strength and for all VDD(s) unless otherwise stated. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 1 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com GENERAL DATA[1] (continued) PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT Condition DC 45 – 55 % All VDDs Tr, Tf – 1 2 ns VDD = 2.5V, 2.8V, 3.0V or 3.3V, 20% - 80% – 1.3 2.5 ns VDD =1.8V, 20% - 80% – 0.8 2 ns VDD = 2.25V - 3.63V, 20% - 80% LVCMOS OUTPUT CHARACTERISTICS Duty Cycle Rise/Fall Time Output High Voltage VOH 90% – – VDD IOH = -4 mA (VDD = 3.0V or 3.3V) Output Low Voltage VOL – – 10% VDD IOL = 4 mA (VDD = 3.0V or 3.3V) Input High Voltage VIH 70% – – VDD Pin 1, OE or ST Input Low Voltage VIL – – 30% VDD Pin 1, OE or ST Input Pull-up Impedence Z_in – 87 100 kΩ Pin 1, OE logic high or logic low, or ST logic high 2 – – MΩ Pin 1, ST logic low T_start – – 5 ms Measured from the time VDD reaches its rated minimum value T_oe – – 130 ns f = 115 MHz. For other frequencies, T_oe = 100 ns + 3* cycles T_resume – – 5 ms Measured from the time ST pin crosses 50% threshold RMS Period Jitter T_jitt – 1.93 3 ps f = 125 MHz, VDD = 2.5V, 2.8V, 3.0V or 3.3V – 1.64 4 ps f = 125 MHz, VDD = 1.8V RMS Phase Jitter (random) T_phj – 0.5 0.9 ps Integration bandwidth = 900 kHz to 7.5 MHz – 1.3 2 ps Integration bandwidth = 12 kHz to 20 MHz INPUT CHARACTERISTICS STARTUP AND RESUME TIMING Startup Time Enable/Disable Time Resume Time JITTER EXCELLENT RELIABILITY DATA MTBF 500 million hours Shock Resistance: 10.000 g Vibration Resistance: 70 g Note: 1. All electrical specifications in the above table are specified with 15 pF output load and for all V DD(s) unless otherwise stated. PIN DESCRIPTION PIN 1 SYMBOL OE/ST/NC TOP VIEW FUNCTIONALITY Output Enable H or Open[2]: specified frequency output L: output is high impedance. Only output driver is disabled. Standby H or Open[2]: specified frequency output L: output is low (weak pull down). Device goes to sleep mode. Supply current reduces to I_std. No Connect OE/ST/NC 1 4 VDD GND 2 3 OUT Any voltage between 0 and VDD or Open[2]: : Specified fre- 2 GND Power Electrically ground[3] 3 OUT Output Oscillator output 4 VDD Power Power supply voltage[3] Note: 2. In OE or ST mode, a pull-up resistor of 10kΩ or less is recommended if pin 1 is not externally driven. If pin 1 needs to be left floating, use the NC option. 3. A capacitor value of 0.1 µF between V DD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 2 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TEST CIRCUIT AND WAVEFORM FIGURE 1. TEST CIRCUIT FIGURE 2. WAVEFORM Vout VDD 3 4 Power Supply Test Point tf 80%VDD 0.1µF 15pF (including probe and fixture capacitance) 2 1 tr 50% 20%VDD High Pulse (TH) Low Pulse (TL) Period VDD OE/ST Function 1kΩ TIMING DIAGRAMS(4) FIGURE 3. STARTUP TIMING (OE/ST MODE) 90%VDD, 2.5/2.8/3.3V devices 95%VDD, 1.8V devices VDD Pin 4 Voltage FIGURE 4. STANDBY RESUME TIMING (ST MODE ONLY) 50%VDD No Glitch first cycle VDD ST Voltage T_resume T_start CLK Output T_start: Time to start from power-off FIGURE 5. OE ENABLE TIMING (OE MODE ONLY) CLK Output T_resume: Time to resume from ST FIGURE 6. OE DISABLE TIMING (OE MODE ONLY) VDD 50%VDD VDD OE Voltage OE Voltage 50%VDD T_OE CLK Output CLK Output T_OE HZ T_OE: Time to re-enable the clock output T_OE: Time to put the output drive in High Z mode Note: 4. LPOP supports no runt pulses and no glitches during startup or resume. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 3 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PERFORMANCE PLOTS(5) FIGURE 7. IDD vs. FREQUENCY FIGURE 8. RMS PERIOD JITTER vs. FREQUENCY 4.0 6.0 3.5 RMS period jitter (ps) 6.5 IDD (mA) 5.5 5.0 4.5 4.0 3.0 2.5 2.0 1.5 1.0 3.5 0.5 3.0 115 117 119 121 123 125 127 129 131 133 135 137 0.0 115 117 119 121 123 125 127 129 131 133 135 137 Frequency (MHz) Frequency (MHz) 1.8 2.5 2.8 3.0 3.3 2.0 0.9 1.8 0.8 1.6 0.7 1.4 2.5 2.8 3.0 3.3 FIGURE 10. RMS PHASE JITTER vs. FREQUENCY IPJ (ps) IPJ (ps) FIGURE 9. RMS PHASE JITTER vs. FREQUENCY 1.8 0.6 1.2 0.5 1.0 115 117 119 121 123 125 127 129 131 133 135 137 0.4 115 117 119 121 123 125 127 129 131 133 135 137 Frequency (MHz) 1.8 2.5 2.8 3.0 Frequency (MHz) 3.3 FIGURE 11. DUTY CYCLE vs. FREQUENCY 1.8 2.5 2.8 3.0 3.3 FIGURE 12. RISE TIME vs. TEMPERATURE, 125 MHZ OUTPUT 2.5 55 54 2.0 Rise Time (ns) Duty Cycle (%) 53 52 51 50 49 48 47 1.5 1.0 0.5 46 45 115 117 119 121 123 125 127 129 131 133 135 137 0.0 -40 -30 -20 -10 0 Frequency (MHz) 1.8 2.5 2.8 3.0 10 20 30 40 50 60 70 80 Temperature (°C) 3.3 1.8 2.5 2.8 3.0 3.3 Note: 5. All plots are measured with 15 pF load at room temperature, unless otherwise stated. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 4 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PROGRAMMABLE DRIVE STRENGTH The LPOP includes a programmable drive strength feature named SoftLevel to provide a simple, flexible tool to optimize the clock rise/ fall time for specific applications. Benefits from the programmable drive strength feature are: HIGH OUTPUT LOAD CAPABILITY The rise/fall time of the input clock varies as a function of the actual capacitive load the clock drives. At any given drive strength, the rise/ fall time becomes slower as the output load increases. As an examp- + Improves system radiated electromagnetic interference (EMI) by le, for a 3.3V LPOP device with default drive strength setting, the typical rise/fall time is 1ns for 15 pF output load. The typical rise/fall slowing down the clock rise/fall time + Improves the downstream clock receiver’s (RX) jitter by decreasing (speeding up) the clock rise/fall time. time slows down to 2.6 ns when the output load increases to 45 pF. One can choose to speed up the rise/fall time to 1.68 ns by then increasing the drive strength setting on the LPOP. + Ability to drive large capacitive loads while maintaining full swing with sharp edge rates. For more detailed information about rise/fall time control and drive strength selection, see the Petermann-Technik Applications Note section: http://www.petermann-technik.com The LPOP can support up to 60 pF or higher in maximum capacitive loads with up to 3 additional drive strength settings. Refer to the Rise/Tall Time Tables to determine the proper drive strength for the desired combination of output load vs. rise/fall time. LPOP DRIVE STRENGTH SELECTION EMI REDUCTION BY SLOWING RISE/FALL TIME (SoftLevel FUNCTION) Figure 13 shows the harmonic power reduction as the rise/fall times Tables 1 through 5 define the rise/fall time for a given capacitive load and supply voltage. 1. are increased (slowed down). The rise/fall times are expressed as a ratio of the clock period. For the ratio of 0.05, the signal is very close voltage (1.8V, 2.5V, 2.8V, 3.0V, 3.3V). 2. to a square wave. For the ratio of 0.45, the rise/fall times are very close to near-triangular waveform. These results, for example, show Select the table that matches the LPOP nominal supply Select the capacitive load column that matches the application requirement (5 pF to 30 pF) 3. that the 11th clock harmonic can be reduced by 35 dB if the rise/fall Under the capacitive load column, select the desired rise/fall times. edge is increased from 5% of the period to 45% of the period. 4. FIGURE 13. HARMONIC EMI REDUCTION AS A FUNCTION OF SLOWER RISE/FALL TIME (SoftLevel FUNCTION) 5. The left-most column represents the part number code for the corresponding drive strength. Harmonic amplitude (dB) 10 Add the drive strength code to the part number for ordering purposes. CALCULATING MAXIMUM FREQUENCY 0 Based on the rise and fall time data given in Tables 1 through 5, the -10 maximum frequency the oscillator can operate with guaranteed -20 full swing of the output voltage over temperature as follows: -30 -40 Max. frequency = -50 1 6 x (Trise) -60 EXAMPLE 1 -70 -80 Calculate fMAX for the following condition: 1 3 trise=0.05 trise=3 5 7 9 Harmonic number trise=0.1 trise=0.15 trise=0.35 trise=0.2 trise=0.4 11 trise=0.25 trise=0.45 + VDD = 3.3V (Table 1) + Capacitive Load: 30pF + Desired Tr/tf time = 2ns (rise/fall time part number code=U) JITTER REDUCTION WITH FASTER RISE/FALL TIME Power supply noise can be a source of jitter for the downstream chip- Part number for the above example: set. One way to reduce this jitter is to increase rise/fall time (edge rate) of the input clock. Some chipsets would require faster rise/fall time in order to reduce their sensitivity to this type of jitter. The LPOP LPOP33-2520-E-25-M-125.000MHz-T-U provides up to 3 additional high drive strength settings for very fast rise/fall time. Refer to the rise/fall time tables to determine the proper drive strength. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS Drive strength code is inserted here. Standard setting is “S” PAGE 5 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com RISE/FALL TIME (20% TO 80%) vs CLOAD TABLE 1. VDD = 1.8V RISE/FALL TIMES FOR SPECIFIC CLOAD RISE/FALL TIME TYP (NS) RISE/FALL TIME TYP (NS) Drive Strength \ CLOAD T TABLE 2. VDD = 2.5V RISE/FALL TIMES FOR SPECIFIC CLOAD 5 pF 15 pF 0.93 n/a(6) E 0.78 n/a U 0.70 1.48 S = standard limit 0.65 1.30 TABLE 3. VDD = 2.8V RISE/FALL TIMES FOR SPECIFIC CLOAD Drive Strength \ CLOAD 5 pF 15 pF R 1.45 n/a B 1.09 n/a T 0.62 1.28 S = standard limit 0.54 1.00 U 0.43 0.96 F 0.34 0.88 TABLE 4. VDD = 3.0V RISE/FALL TIMES FOR SPECIFIC CLOAD RISE/FALL TIME TYP (NS) Drive Strength \ CLOAD RISE/FALL TIME TYP (NS) 5 pF 15 pF 30 pF Drive Strength \ CLOAD 5 pF 15 pF 30 pF R 1.29 n/a n/a R 1.22 n/a n/a B 0.97 n/a n/a B 0.89 n/a n/a T 0.55 1.12 n/a S = standard limit 0.51 1.00 n/a S = standard limit 0.44 1.00 n/a E 0.38 0.92 n/a U 0.34 0.88 n/a U 0.30 0.83 n/a F 0.29 0.81 1.48 F 0.27 0.76 1.39 TABLE 5. VDD = 3.3V RISE/FALL TIMES FOR SPECIFIC CLOAD RISE/FALL TIME TYP (NS) Drive Strength \ CLOAD 5 pF 15 pF 30 pF R 1.16 n/a n/a B 0.81 n/a n/a S = standard limit 0.46 1.00 n/a E 0.33 0.87 n/a U 0.28 0.79 1.46 F 0.25 0.72 1.31 Note: 6. “n/a” indicates that the resulting rise/fall time from the respective combination of the drive strength and output load does not provide rail-to-rail swing and is not available CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 6 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [7] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 2.0 X 1.6 X 0.75 MM #1 1.5 0.65 #3 #3 #1 #2 #2 0.8 1.2 0.93 #4 0.48 2.0±0.05 1.6±0.05 #4 0.9 0.75±0.05 0.68 RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 2.5 X 2.0 X 0.75 MM #1 1.9 1.00 #3 #3 #1 #2 #2 1.0 1.1 1.5 #4 0.5 2.5±0.05 2.0±0.05 #4 1.1 0.75±0.05 0.75 RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 3.2 X 2.5 X 0.75 MM #3 #1 #2 #2 1.2 0.9 1.9 #4 0.9 1.4 0.75±0.05 #1 2.2 2.1 #3 0.7 3.2±0.05 2.5±0.05 #4 Note: 7. A capacitor value of 0.1 µF between VDD and GND is recommended (see note 2 + 3). CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 7 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [8] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0 X 3.2 X 0.75 MM #1 2.54 2.39 #3 #3 #1 #2 #2 1.6 0.8 2.2 #4 1.1 5.0±0.05 3.2±0.05 #4 1.5 0.75±0.05 1.15 RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0 X 5.0 X 0.90 MM #3 #1 #2 3.81 #4 #2 2.0 1.1 1.4 2.2 0.90±0.10 #1 5.08 5.08 #3 2.6 7.0±0.05 5.0±0.05 #4 REFLOW SOLDER PROFILE Note: 8. A capacitor value of 0.1 µF between VDD and GND is recommended (see note 2 + 3). CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 8 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION OSCILLATOR FAMILY LPOP SUPPLY VOLTAGE “18“ for 1.8V “25“ for 2.5V “28“ for 2.8V “3“ for 3.0V “33“ for 3.3V “XX“ for 2.25V to 3.63V FREQUENCY TEMPERATURE RANGE 115.000001 to 137.000000 MHz “C” for 0 +70°C “D” for -10 +70°C “M” for -20 +70°C “W” for -40 +85°C LPOP 33-2520-E-25-M-125.000MHz-T-S FREQUENCY STABILITY “20” for ±20 PPM “25” for ±25 PPM “50” for ±50 PPM PACKAGE SIZE “2016” for 2.0 X 1.6 mm “2520” for 2.5 X 2.0 mm “3225” for 3.2 X 2.5 mm “5032” for 5.0 X 3.2 mm “7050” for 7.0 X 5.0 mm PACKING METHOD “B” for BULKS or TUBES “T” for TAPE & REEL FEATURE PIN 1 OUTPUT DRIVE STRENGTH “E” for OUTPUT ENABLE “S” for STANDBY “N” for NO CONNECT “S” Standard (datasheet limits) See Tables 1 to 5 for rise/fall times “R” “E” “B” “U” “T” “F” EXAMPLE: LPOP-33-2520-E-25-M-125.000MHz-T-S PLEASE INDICATE YOUR REQUIRED PARAMETERS EXPRESS SAMPLES ARE DELIVERABLE ON THE SAME DAY IF ORDERED UNTIL 02:00 PM! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 9 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 10 OF 10 I SPEC 01 I REV.00 I NOVEMBER 2014