MEMS Oscillator, Ultra Performance, LVCMOS/HCMOS Compatible, 1.00 MHz to 80.00 MHz Features: Typical Applications: MEMS Technology Direct pin to pin drop-in replacement for industry-standard packages Ultra-low phase jitter: 0.5 pSec (12 kHz to 20 MHz) LVCMOS/HCMOS Compatible Output Industry-standard package 2.5 x 2.0, 3.2 x 2.5, and 5.0 x 3.2 mm x mm Pb-free, RoHS and REACH compliant Fast delivery times IM810 Series Fibre Channel Server and Storage GPON, EPON 100M / 1G /10G Ethernet Electrical Specifications: Frequency Range Frequency Stability First Year Aging 10 Years Aging Operating Temperature Supply Voltage (Vdd) ±10% Current Consumption OE Disable Current Standby Current 1.000 MHz to 80.000MHz See Part Number Guide ±1.5 ppm ±5.0 ppm See Part Number Guide See Part Number Guide 31 mA typ./ 33 mA max 29 mA typ./ 31mA max 31 mA max 30 mA max 70 µA max 10 µA max Waveform Output Symmetry Rise / Fall Time Logic “1” Logic “0” Input Voltage High LVCMOS/HCMOS 45%/55% 1.2 nSec typ./ 2.0 nSec max 90% of Vdd min 10% of Vdd max 70% of Vdd min Input Voltage Low Input Pull-up Impedance 30% of Vdd max 100 kΩ typ./ 250 kΩ max 2.0 MΩ min Startup Time OE Enable/Disable Time Resume Time RMS Period Time 7 mSec typ./ 10 mSec max 150 nSec max 6 mSec typ./ 10 mSec max 1.5 pSec typ./ 2.0 pSec max 2.0 pSec typ./ 3.0 pSec max 0.5 pSec typ./ 1.0 pSec max RMS Period Time (random) Inclusive of Initial Tolerance, Operating Temperature Range, Load, and Voltage. At + 25ºC ±2ºC At + 25ºC ±2ºC No load condition, F = 20 MHz, Vdd = +2.5 V, +2.8 V or +3.3 V No load condition, f = 20 MHz, Vdd = +1.8V Vdd = +2.5 V, +2.8 V or 3.3 V, OE = GND Vdd = +1.8 V, OE = GND Vdd = +2.5 V, +2.8 V or 3.3 V, ST = GND Vdd = +1.8 V, ST = GND 50% of waveform 15 pF Load, 10% to 90% of Vdd Pin 1, OE or ST Pin 1, OE or ST Pin 1, OE logic high or logic low, or ST logic high Pin 1, ST logic low Measured from the time Vdd reaches its rated minimum values F = 80 MHz, For other frequencies, T_oe = 100 nSec = 3 cycles In standby mode, measured from the time ST pin crosses 50% threshold. F = 75 MHz, all Vdds F = 10 MHz, Integration bandwidth = 12 kHz to 20 MHz Notes: All min and max limits are specified over temperature and rated operating voltage with 15pF output unless otherwise stated. Typical values are at +25ºC and nominal supply voltage. Absolute Maximum Limits Storage Temperature Supply Voltage (Vdd) Electrostatic Discharge Solder Temperature (follow standard Pb free soldering guidelines) Junction Temperature -65ºC to +150ºC -0.5 VDC to 4.0 VDC 2000 V max 260ºC max 150ºC max ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev 01/30/16_A Page 1 of 8 MEMS Oscillator, Ultra Performance, LVCMOS/HCMOS Compatible, 1.00 MHz to 80.00 MHz IM810 Series Ordering Information: Part Number Guide Packages IM810B – 5.0 x 3.2 IM810C – 3.2 x 2.5 IM810D – 2.5 x 2.0 Input Voltage 1 = +1.8 V 6 = +2.5 V 2 = +2.8 V 7 = +3.0 V 3 = +3.3 V Operating Temperature 1 = 0ºC to +70ºC 2 = -40ºC to +85ºC 3 = -20ºC to +70ºC Output Drive Strength - = Default (see tables 2 through 4) Stability (ppm) E - ±10 F = ±20 A = ±25 B = ±50 Select Function Frequency H = Tri-state S = Standby - Frequency Sample Part Number: IM810C-62-FS-10.0000MHz This 10.0000 MHz oscillator in a 3.2 x 2.5 package with stability ±20 ppm from -40ºC to +85ºC using a supply voltage of +2.5 V. The Output Drive Strength (Rise and Fall Time) is 2.00 nSec per Table 3 with 30 pF load. With Pin 1 function as Standby Sample Part Number: IM810B-23FAH-66.0000MHz This 66.0000 MHz oscillator in a 5.0 x 3.2 package with stability ±20 ppm from -40ºC to +85ºC using a supply voltage of +2.8 V. The Output Drive Strength (Rise and Fall Time) is 1.29 nSec per Table 1 with 15 pF load. With Pin 1 function as Tri-state Notes: Not all options are available at all frequencies and temperatures ranges. Please consult with sales department for any other parameters or options. Oscillator specification subject to change without notice. Phase Noise: Figure 1: Phase Noise, 10 MHz, +3.0 V LVCMOS Output ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev 01/30/16_A Page 2 of 8 MEMS Oscillator, Ultra Performance, LVCMOS/HCMOS Compatible, 1.00 MHz to 80.00 MHz IM810 Series Performance Plots: Figure 2: Idd vs Frequency Figure 3: RMS Period vs Frequency Figure 4: Duty Cycle vs Frequency Figure 5: RMS Phase Jitter vs Frequency Figure 6: Idd vs Temperature, 10 MHz Output Firgure 7: Rise Time vs Temperature, 75 MHz Output ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev 01/30/16_A Page 3 of 8 MEMS Oscillator, Ultra Performance, LVCMOS/HCMOS Compatible, 1.00 MHz to 80.00 MHz IM810 Series Waveform Test Circuit Environmental Specifications: Environmental Compliance Parameter Condition/Test Method MIL-STD-883F, Method 2002 MIL-STD-883F, Method 2007 JESD22, Method A104 MIL-STD-883F, Method 2003 MSL Level 1 at +260ºC Mechanical Shock Mechanical Vibration Temperature Cycle Solderability Moisture Sensitivity Level Pb Free Solder Reflow Profile Units are backward compatible with +240ºC reflow processes Ts max to TL (Ramp-up Rate) Preheat Temperature min (Ts min) Temperature typ (Ts typ) Temperature max (Ts max) Time (Ts) Ramp-up Tate (TL to Tp Time Maintained Above Temperature (TL) Time (TL) Peak Temperature (Tp) Time within 5ºC to Peak Temperature (Tp) Ramp-down Rate Tune 25ºC to Peak Temperature Moisture Sensitivity Level (MSL) ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice 3ºC / second max 150ºC 175ºC 200ºC 60 to180 seconds 3ºC / second max 217ºC 60 to 150 seconds 260ºC max for seconds 20 to 40 seconds 6ºC / second max 8 minute max Level 1 Rev 01/30/16_A Page 4 of 8 MEMS Oscillator, Ultra Performance, LVCMOS/HCMOS Compatible, 1.00 MHz to 80.00 MHz IM810 Series Pin Functionally Pin Symbol OE Tri-state ST Standby 1 Pin Description Functionality High or Open = specified frequency output Low = Output is high impedance, only output is disabled. High or Open = specified frequency output. Low = Output is low. Device goes to sleep mode. Supply current reduces to standby current. Electrical ground Oscillator output Power supply voltage 2 GND Power 3 Out Output 4 Vdd Power Notes: 1. In OE or ST mode, a pull-up resistor of 10.0 kΩ or less is recommended if Pin 1 is not externally driven 2. A capacitor of value 0.1 µF or higher between Pin 4 (Vdd) and Pin 1 (GND) is required. Pin Assignments OE 1 ST 4 Vdd 3 OUT Top View GND 2 Timing Diagrams: Figure 8: Startup Timing (OE/ Mode) Figure 10: OE Enable Timing (OE Mode Only) Figure 9: Standby Resume Timing ( Mode Only) Figure 11: OE Disable Timing (OE Mode Only) Notes: IM810 supports gated output which is accurate within rated frequency stability from the first cycle ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev 01/30/16_A Page 5 of 8 MEMS Oscillator, Ultra Performance, LVCMOS/HCMOS Compatible, 1.00 MHz to 80.00 MHz IM810 Series Selectable Drive Strength Options Rise/Fall Time (20% to 80%) vs CLOAD Tables Rise/Fall Time Typ (nS) Drive Strength (CLOAD) L A R B S D T E U F W G X K Y Q - = Default M N P 5 pF 15 pF 30 pF 45 pF 60 pF 12.45 6.50 4.38 3.27 2.62 2.19 1.76 1.59 1.49 1.22 1.07 1.01 0.96 0.92 0.88 0.86 0.82 0.77 0.66 0.51 17.68 10.27 7.05 5.30 4.25 3.52 3.01 2.59 2.28 2.10 1.88 1.64 1.50 1.41 1.34 1.29 1.24 1.20 1.15 1.09 19.48 16.21 11.61 8.89 7.20 6.00 5.14 4.49 3.96 3.57 3.23 2.96 2.74 2.56 2.39 2.24 2.07 1.94 1.84 1.76 46.21 23.92 16.17 12.18 9.81 8.31 7.10 6.25 5.55 5.00 4.50 4.12 3.80 3.52 3.25 3.04 2.89 2.72 2.58 2.45 57.82 30.76 20.83 15.75 12.65 10.59 9.15 7.98 7.15 6.46 5.87 5.40 4.98 4.64 4.32 4.06 3.82 3.61 3.41 3.24 Table 1: Vdd = +1.8 V Rise/Fall time for Specific CLOAD Drive Strength (CLOAD) L A R B S D T E U F W - = Default X K Y Q Z M N P 45 pF 60 pF 32.70 16.60 11.19 8.55 6.85 5.68 4.84 4.20 3.73 3.34 3.04 2.79 2.56 2.37 2.20 2.07 1.95 1.85 1.77 1.70 42.06 21.38 14.59 11.04 8.80 7.33 6.26 5.51 4.92 4.42 4.02 3.69 3.43 3.18 2.98 2.80 2.65 2.50 2.39 2.28 Table 2: Vdd = +2.5 V Rise/Fall time for Specific CLOAD Rise/Fall Time Typ (nS) Rise/Fall Time Typ (nS) Drive Strength (CLOAD) L A R B S D T E U F W - = Default X K Y Q Z M N P Rise/Fall Time Typ (nS) 15 5 pF 30 pF pF 8.68 13.59 18.36 4.42 7.18 11.93 2.93 4.78 8.15 2.21 3.57 6.19 1.67 2.87 4.94 1.50 2.33 4.11 1.06 2.04 3.50 0.98 1.69 3.03 0.93 1.48 2.69 0.90 1.37 2.44 0.87 1.29 2.21 0.67 1.20 2.00 0.44 1.10 1.86 0.38 0.99 1.76 0.36 0.83 1.66 0.34 0.71 1.58 0.33 0.65 1.51 0.32 0.62 1.44 0.31 0.59 1.37 0.30 0.57 1.29 5 pF 15 pF 30 pF 45 pF 60 pF 7.93 4.06 2.68 2.00 1.59 1.19 1.00 0.94 0.90 0.87 0.62 0.41 0.37 0.35 0.33 0.32 0.31 0.30 0.30 0.29 12.69 6.66 4.40 3.25 2.57 2.14 1.79 1.51 1.38 1.29 1.19 1.08 0.96 0.78 0.67 0.63 0.60 0.57 0.56 0.54 17.94 11.04 7.53 5.66 4.54 3.76 3.20 2.78 2.48 2.21 1.99 1.84 1.72 1.63 1.54 1.46 1.39 1.31 1.22 1.13 30.10 15.31 10.29 7.84 6.27 5.21 4.43 3.84 3.40 3.03 2.76 2.52 2.33 2.15 2.00 1.89 1.80 1.72 1.63 1.55 38.89 19.80 13.37 10.11 8.07 6.72 5.77 5.06 4.50 4.05 3.68 3.36 3.15 2.92 2.75 2.57 2.43 2.30 2.22 2.13 Table 3: Vdd = +2.8 V Rise/Fall time for Specific CLOAD Drive Strength (CLOAD) L A R B S D T E U - = Default W G X K Y Q Z M N P 5 pF 15 pF 30 pF 45 pF 60 pF 7.18 3.61 2.31 1.65 1.43 1.01 0.94 0.90 0.86 0.48 0.38 0.36 0.34 0.33 0.32 0.32 0.30 0.30 0.30 0.29 11.59 6.02 3.95 2.92 2.26 1.91 1.51 1.36 1.25 1.15 1.04 0.87 0.70 0.63 0.60 0.58 0.56 0.55 0.54 0.52 17.24 10.19 6.88 5.12 4.09 3.38 2.86 2.50 2.21 1.95 1.77 1.66 1.56 1.48 1.40 1.31 1.22 1.12 1.02 0.95 27.57 13.98 9.42 7.10 5.66 4.69 3.97 3.46 3.03 2.72 2.47 2.23 2.04 1.89 1.79 1.69 1.62 1.54 1.47 1.41 35.57 18.10 12.24 9.17 7.34 6.14 5.25 4.58 4.07 3.65 3.31 3.03 2.80 2.61 2.43 2.28 2.17 2.07 1.97 1.90 Table 4: Vdd= +3.0 V Rise/Fall time for Specific CLOAD ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev 01/30/16_A Page 6 of 8 MEMS Oscillator, Ultra Performance, LVCMOS/HCMOS Compatible, 1.00 MHz to 80.00 MHz IM810 Series Mechanical Details: Package Dimensions and Suggest Land Pattern Option D: 2.70 x 2.40 Package (100% compatible with 2.50 x 2.00 ) 1.00 2.70 ±0.05 1.90 3 Marking Suggested Land Pattern 2.40 ±0.05 1.10 4 Bottom View 2 0.80 max 1 0.5 1.50 1.0 0.75 1.1 Option C: 3.20 x 2.50 Package Suggested Land Pattern 3.20 ±0.05 2.1 2.20 3 Marking 2.50±0.05 0.90 4 Bottom View 1 2 0.80 max 0.7 1.90 1.2 0.9 1.4 Opton B: 5.00 x 3.20 Package Suggested Land Pattern 5.00 ±0.05 2.39 3 Marking 3.20 ±0.05 0.80 4 Bottom View 2 0.80 max 2.54 1 1.1 2.20 1.6 1.15 1.5 Marking Line 1 = XXXXX (Lot Code) Dot to denote Pin 1 location Package Information Leadframe: C194 Plating: NiPdAu ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev 01/30/16_A Page 7 of 8 MEMS Oscillator, Ultra Performance, LVCMOS/HCMOS Compatible, 1.00 MHz to 80.00 MHz IM810 Series Tape and Reel Dimensions PITCH Q1 Q2 REEL DIA TAPE WIDTH Q3 Q4 DIRECTION OF FEED REF: EIA-481-E Part Number Size Pitch Tape Width Pin Orient. IM810B 5.0 x 3.2 8.0 ± 0.1 12.3 max Q1 IM810C IM810D 3.2 x 2.5 2.5 x 2.0 4.0 ± 0.1 4.0 ± 0.1 8.3 max 8.3 max Q1 Q1 Reel Dia. 180 330 180 180 Count 1000 3000 3000 3000 Notes: All dimensions are in mm. Do not scale drawings. PROPRIETARY AND CONFIDENTIAL THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION, AND SUCH INFORMATION MAY NOT BE DISCLOSED TO OTHERS FOR ANY PURPOSE NOR USED FOR MANUFACTURING PURPOSES WITHOUT WRITTEN PERMISSION FROM ILSI America. ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ● www.ilsiamerica.com Specifications subject to change without notice Rev 01/30/16_A Page 8 of 8