MWC Series – 2.0 x 1.6 Oscillator Specification ¾ 2.0 X 1.6 SMT Package ¾ CMOS Output ¾ Tri-state Option ¾ Tape and Reel Packaging Available ELECTRICAL SPECIFICATION: Frequency Range Temperature Stability (Inslusie of Temperature, Load, Voltage, and Aging) Operating Temperature Range Storage Temperature Range Supply Voltage (VDD) ±10% Supply Current Output Logic “0” Logic “1” Symmetry (50% of waveform) Rise and Fall Time (20% to 80% of waveform) Load Start Up Time 1.000MHZ to 80.000MHZ (See part Number Guide for Options) (See part Number Guide for Options) -40ºC to +85ºC +1.80 VDC +2.50 VDC +3.30 VDC 4 mA max 4 mA max 4 mA max CMOS Less than 10% of Supply Voltage Greater than 90% Supply Voltage (See part Number Guide for Options) 6 nSec 15pF 10 msec Voh = 70% of Vdd min or No Connection to Enable Output Vol = 30% of Vdd max or grounded to Disable Output (High Impedance) Tri-state Operation PART NUMBER GUIDE: MW Frequency C 2.0 x 1.6 Ceramic SMD 4 Pads Supply Voltage Output C = CMOS 1 = +1.80 VDC 2 = +2.50 VDC 3 = +3.30 VDC Frequency Stability 020 = ±20 ppm 025 = ±25 ppm 050 = ±50 ppm 100 = ±100 ppm Operating Temperature Blank = 0°C to +70°C 27 = -20°C to +70°C 48 = -40°C to +85°C Symmetry Blank = 40%/60% A = 45%/55% Pin 1 Connection Packaging Blank = No Connection H = Tri-state Blank = Bulk T = Tape and Reel Please Consult with MMD Sales Department for any other Parameters or Options MMD Components, 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] In the event of conflict, the requirements of this specification shall govern Specification Subject to change without notice Revision: Pb RoHS Free Compliant MWC111509A Page 1 of 2 MECHANICAL DIMENSIONS: 2.10 [.083] MAX MXX.XXX SYYWWL 0.80 [.031] MAX 0.70 [.028] 1.70 [.067] MAX 1.50 [.059] 3 4 2 1 1.00 [.039] 0.50 [.020] PIN 1 PIN 2 PIN 3 PIN 4 PIN CONNECTIONS TRI-STATE OR NO CONNECTION OUTPUT CASE GROUND SUPPLY VOLTAGE 0.75 [.030] PIN 1 DESIGNATOR LOCATED 0.60 [.024] IN THIS AREA DIMENSION IN BRACKETS ARE IN INCHES EXTERNAL BYPASS CAPACITOR IS RECOMMENDED SUGGESTED LAND PATTERN ENVIRONMENTAL/MECHANICAL SPECIFICATION: Shock Solderability Vibration Gross Leak Test Fine Leak Test Reflow Solder 0.65 [.026] 0.50 [.020] MIL-STD-883, Meth 2002, Cond MIL-STD-883, Meth 2003 MIL-STD-883, Meth 2007, Cond MIL-STD-883, Meth 1014, Cond MIL-STD-883, Meth 1014, Cond +260ºC for 10 sec max MARKING DETAIL: Line 1 = MXX.XXX M = MMD COMPONENTS XX.XXX = Frequency in MHZ Line 2 = SYYWWL S = Internal Code YYWW = 4 Digit Date Code (Year / Week) L = Denotes RoHS Compliant Pin 1 Designator B A C A TAPE AND REEL DIMENSIONS: PITCH TAPE WIDTH B0 REEL DIA K0 A0 Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 PITCH TAPE WIDTH REEL DIA QTY PER REEL PIN 1 ORIENT. 4.0 8.0 180 1000 Q1 NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters. 3. Tolerances are ±0.1 mm unless otherwise specified. 4. Do not scale drawing. DIRECTION OF FEED MMD Components, 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] In the event of conflict, the requirements of this specification shall govern Specification Subject to change without notice Revision: Pb RoHS Free Compliant MWC111509A Page 2 of 2