MUL Series 5X3.2 Ceramic SMD Oscillator 5 x 3.2 SMD Package 6 Pin LVPECL Output Tristate Option Tape & Reel Packaging Available Frequency Range 74.250MHZ to 161.1328MHZ Temperature Stability (Inclusive of Temperature, Load, Voltage, and Aging) (See Part Number Guide for Options) Operating Temperature Range (See Part Number Guide for Options) Storage Temperature Range -55°C to +125°C Supply Voltage (Vdd) ±5% (See Part Number Guide for Options) Supply Current 75mA max Output LVPECL Logic “0” Vdd - 1.60V max., (nom., Load) Logic “1” Vdd - 1.03V min., (nom., Load) Load 50Ω into Vdd-2.0VDC Symmetry (50% of waveform) (See Part Number Guide for Options) Rise/Fall Time (20% to 80%) 300p Sec typ, 700pSec max RMS Phase Jitter (12kHZ to 20MHZ) 1pSec max 100 Hz = -95 dBc/Hz 1 kHz = -125 dBc/Hz Phase Noise 10 kHz = -143 dBc/Hz 100 kHz = -146 dBc/Hz Start-up Time Tri-state Operation 10mSec max Voh = 70% of Vdd min or No Connection to Enable Output Vol = 30% max or grounded to Disable Output (High Impedance) Mechanical & Environmental Detail Shock Solderability MIL-STD-883, Method 2002 Cond B MIL-STD-883, Method 2003 Vibration MIL-STD-883, Method 2007, Cond A Gross Leak Test MIL-STD-883, Method 1014, Cond C Fine Leak Test MIL-STD-883, Method 1014, Cond A2 Reflow Solder +260°C for 10 sec max Marking Detail Line 1 = MXXXXX M = XXXXX = Line 2 = SYYWWL S = = YYWW MMD Frequency in MHZ Internal Code 4 Digit Date Code (Year / Week) Denotes RoHS Compliant L = Line 3 = XXXXX Internal use only May vary with lots Black dot to denote Pin 1 MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Subject to change without notice 04/10/16 D Pg 1 of 2 Part Number Guide MU Frequency L 5 x 3.2 Ceramic SMD 6 Pads Frequency Stability 020 = ±20 ppm 025 = ±25 ppm 050 = ±50 ppm 100 = ±100 ppm Supply Voltage Output L=LVPECL 2 = +2.50 VDC 3 = +3.30 VDC Operating Temperature Blank = 0°C to +70°C 27 = -20°C to +70°C 48 = -40°C to +85°C Symmetry Blank = 40%/60% A = 45%/55% Pin 1 Connection Packaging Blank = No Connection H = Tri-state Blank = Bulk T = Tape and Reel Please Consult with MMD Sales Department for any other Parameters or Options Mechanical Details 5.15 [.203] MAX MXX.XXX SYYWWL 2.54 [.100] 2.54 [.100] 1.30 [.051] 1.27 [.050] 1.27 [.050] 4 5 6 3 2 1 0.80 [.031] 3.35 [.132] MAX 1.00 [.039] PIN 1 DESIGNATOR LOCATED IN THIS AREA. 0.64 [.025] 1.40 [.055] PIN CONNECTIONS PIN 1 TRI-STATE OR NO CONNECTION NO CONNECTION PIN 2 CASE GROUND PIN 3 OUTPUT PIN 4 PIN 5 COMPLEMENTARY OUTPUT SUPPLY VOLTAGE PIN 6 1.00 [.039] DIMENSION IN BRACKETS ARE IN INCHES EXTERNAL BYPASS CAPACITOR IS RECOMMENDED RECOMMENDED LAND PATTERN Tape & Reel Dimensions PITCH TAPE WIDTH REEL DIA Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PITCH TAPE WIDTH REEL DIA QTY PER REEL PIN 1 ORIENT. 8.00 [.315] 16.00 [.630] 180[7 IN] 1000 Q1 NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters. 3. Tolerances are ±0.10 [.004] mm unless otherwise specified. 4. Do not scale drawing. DIRECTION OF FEED MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Subject to change without notice 04/10/16 D Pg 2 of 2