MUV Series 5X3.2 Ceramic SMD Oscillator 5 x 3.2 SMD Package 6 Pin LVDS Output Tristate Option Tape & Reel Packaging Available Frequency Range Temperature Stability (Inclusive of Temperature, Load, Voltage, and Aging) Operating Temperature Range Storage Temperature Range Supply Voltage (Vdd) ±5% Supply Current Output Logic “1” Logic “0” Differential Output Voltage Offset Voltage Differential Output Error Offset Error Output Swing Symmetry (50% of waveform) Load Rise/Fall Time (20% to 80%) RMS Phase Jitter (12kHZ to 20MHZ) Phase Noise 10 Hz 1 KHz 10 KHz 100 KHz Start-up Time Standby Current 30µA max Mechanical & Environmental Detail MIL-STD-883, Method 2002 Cond B Solderability MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 Vibration MIL-STD-883, Method 2007, Cond A Gross Leak Test MIL-STD-883, Method 1014, Cond C Fine Leak Test MIL-STD-883, Method 1014, Cond A2 MSL -95dBc/Hz -125dBc/Hz -143dBc/Hz -146dBc/Hz 10mSec max Voh = 70% of Vdd min or No Connection to Enable Output Vol = 30% max or grounded to Disable Output (High Impedance) Tri-state Operation Shock 74.250MHZ to 166.00MHZ (See Part Number Guide for Options) (See Part Number Guide for Options) -55°C to +125°C +2.50 VDC +3.30 VDC 63mA max 65mA max LVDS +1.43 VDC typ, +1.60 VDC max +1.10 VDC typ, +0.90 VDC min +330mV, +454mV max +1.250 V, +1.375V max 50 mV max 150 mV max 250 mV min (See Part Number Guide for Options) 100Ω Between Output and Complementary Output 300pSec, 700pSec max 1pSec max Level 1 per IPC/JEDEC J-STD 20 Marking Detail Line 1 = MXXXXX M = XXXXX = Line 2 = SYYWWL S = = YYWW MMD Frequency in MHZ Internal Code 4 Digit Date Code (Year / Week) Denotes RoHS Compliant L = Line 3 = XXXXX Internal use only May vary with lots Black dot to denote Pin 1 MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Subject to change without notice 03/01/11 C Pg 1 of 2 Part Number Guide MU Frequency V 5 x 3.2 Ceramic SMD 6 Pads Frequency Stability 020 = ±20 ppm 025 = ±25 ppm 050 = ±50 ppm 100 = ±100 ppm Supply Voltage Output V = LVDS 2 = +2.50 VDC 3 = +3.30 VDC Operating Temperature Blank = 0°C to +70°C 27 = -20°C to +70°C 48 = -40°C to +85°C Symmetry Blank = 40%/60% A = 45%/55% Pin 1 Connection Packaging Blank = No Connection H = Tri-state Blank = Bulk T = Tape and Reel Please Consult with MMD Sales Department for any other Parameters or Options Mechanical Details 5.15 [.203] MAX MXX.XXX SYYWWL 2.54 [.100] 2.54 [.100] 1.30 [.051] 1.27 [.050] 1.27 [.050] 4 5 6 3 2 1 0.80 [.031] 3.35 [.132] MAX 1.00 [.039] PIN 1 DESIGNATOR LOCATED IN THIS AREA. 0.64 [.025] 1.40 [.055] PIN CONNECTIONS PIN 1 TRI-STATE OR NO CONNECTION NO CONNECTION PIN 2 CASE GROUND PIN 3 OUTPUT PIN 4 PIN 5 COMPLEMENTARY OUTPUT SUPPLY VOLTAGE PIN 6 1.00 [.039] DIMENSION IN BRACKETS ARE IN INCHES EXTERNAL BYPASS CAPACITOR IS RECOMMENDED RECOMMENDED LAND PATTERN Tape & Reel Dimensions PITCH TAPE WIDTH REEL DIA Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PITCH TAPE WIDTH REEL DIA QTY PER REEL PIN 1 ORIENT. 8.00 [.315] 16.00 [.630] 180[7 IN] 1000 Q1 NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters. 3. Tolerances are ±0.10 [.004] mm unless otherwise specified. 4. Do not scale drawing. DIRECTION OF FEED MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Subject to change without notice 03/01/11 C Pg 2 of 2