IDT74CBTLV16214 LOW-VOLTAGE 12-BIT 3:1 MUX / DEMUX BUS SWITCH INDUSTRIAL TEMPERATURE RANGE LOW-VOLTAGE 12-BIT 3:1 MUX / DEMUX BUS SWITCH FEATURES: IDT74CBTLV16214 DESCRIPTION: 5Ω Ω A/B bi-directional switch Isolation Under Power-Off Conditions Over-voltage tolerant Latch-up performance exceeds 100mA VCC = 2.3V - 3.6V, normal range ESD >2000V per MIL-STD-883, Method 3015; >200V using machine model (C = 200pF, R = 0) • Available in SSOP, TSSOP, and TVSOP packages • • • • • • The CBTLV16214 provides a set of 12 high-speed buses switching between three separate ports. The low ON resistance allows inputs to be connected to outputs without adding propagation delay. The CBTLV16214 operates as a 12-bit bus select through the data select (S0-S2) terminals. APPLICATIONS: • Muxing and demuxing • 3.3V High Speed Bus Switching and Bus Isolation • Hot-swapping, hot-docking FUNCTIONAL BLOCK DIAGRAM 1A 2 SIMPLIFIED SCHEMATIC, EACH SWITCH 54 SW 53 SW SW 3 1B1 1B2 1B3 A 12A 27 30 SW 29 SW SW 28 B 12B1 12B2 12B3 FLOW CONTROL CIRCUITRY S0 S1 S2 1 56 55 The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE AUGUST 2002 1 c 2002 Integrated Device Technology, Inc. DSC-5890/5 IDT74CBTLV16214 LOW-VOLTAGE 12-BIT 3:1 MUX / DEMUX BUS SWITCH INDUSTRIAL TEMPERATURE RANGE PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS(1) Symbol S0 1 56 S1 VCC 1A 2 55 S2 VI 1B3 3 54 1B1 2A 4 53 1B2 2B3 5 52 2B1 Description IIK Max. Unit Supply Voltage Range –0.5 to 4.6 V Input Voltage Range –0.5 to 4.6 V Continuous Channel Current 128 mA Input Clamp Current, VI/O < 0 –50 mA –65 to +150 °C Storage Temperature Range TSTG NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 3A 6 51 2B2 3B3 7 50 3B1 GND 8 49 GND 4A 9 48 3B2 4B3 10 47 4B1 5A 11 46 4B2 5B3 12 45 5B1 6A 13 44 5B2 6B3 14 43 6B1 7A 15 42 6B2 xA Port A Inputs or Outputs 7B3 16 41 7B1 xBx Port B Inputs or Outputs VCC 17 40 7B2 8A 18 39 8B1 GND 19 38 GND 8B3 20 37 8B2 9A 21 36 9B1 S2 S1 9B3 22 35 9B2 L L L Z Disconnect L L H B1 A Port = B1 Port L H L B2 A Port = B2 Port L H H Z Disconnect H L L Z Disconnect H L H B3 A Port = B3 Port H H L B1 A Port = B1 Port H H H B2 A Port = B2 Port 10A 23 34 10B1 10B3 24 33 10B2 11A 25 32 11B1 11B3 26 31 11B2 12A 27 30 12B1 12B3 28 29 12B2 PIN DESCRIPTION Pin Names Description Sx Data Select Inputs FUNCTION TABLE(1) Inputs Inputs/Outputs S0 A Operation NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level Z = High-Impedance SSOP/ TSSOP/ TVSOP TOP VIEW OPERATING CHARACTERISTICS(1) Symbol Parameter VCC Supply Voltage VIH High-Level Control Input Voltage VIL Low-Level Control Input Voltage TA Operating Free-Air Temperature Test Conditions Min. Max. Unit 2.3 3.6 V VCC = 2.3V to 2.7V 1.7 — V VCC = 2.7V to 3.6V 2 — VCC = 2.3V to 2.7V — 0.7 VCC = 2.7V to 3.6V NOTE: 1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. 2 — 0.8 –40 +85 V °C IDT74CBTLV16214 LOW-VOLTAGE 12-BIT 3:1 MUX / DEMUX BUS SWITCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Operating Condition: TA = –40°C to +85°C Symbol Typ.(1) Max. — — –1.2 V — — ±1 µA — — 5 µA VCC = 0V, VI or VO = 0V or 3.6V — — 10 µA VCC = 3.6V, IO = 0, VI = VCC or GND — — 10 µA Parameter Test Conditions Control Inputs, Data I/O VCC = 3V, II = –18mA Control Inputs VCC = 3.6V, VI = VCC or GND Data I/O VCC = 3.6V, VO = 0V or 3.6V switch disabled IOFF ICC VIK II I OZ Min. Unit ∆ICC(2) Control Inputs VCC = 3.6V, one input at 3V, other inputs at VCC or GND — — 300 µA CI Control Inputs VI = 3V or 0 — 4 — pF A VO = 3V or 0 (switch off) — 20 — pF CIO(OFF) B Max. at VCC = 2.3V — 7.5 — VI = 0 IO = 64mA — 5 8 IO = 24mA — 5 8 VI = 1.7V IO = 15mA — 27 40 VI = 0 IO = 64mA — 5 7 IO = 24mA — 5 7 VI = 2.4V IO = 15mA — 10 15 Typ. at VCC = 2.5V RON(3) VCC = 3V Ω NOTES: 1. Typical values are at 3.3V, +25°C ambient. 2. The increase in supply current is attributable to each input that is at the specified voltage level rather than VCC or GND. 3. This is measured by the voltage drop between the A and B terminals at the indicated current through the switch. SWITCHING CHARACTERISTICS VCC = 2.5V ± 0.2V Symbol tPD(1) Parameter Propagation Delay VCC = 3.3V ± 0.3V Min. Max. Min. Max. Unit — 0.15 — 0.25 ns 1 6.5 1 6 ns 1 6.5 1 6 ns 1 7 1 6.5 ns A to B or B to A tPD Propagation Delay S to A or B tEN Output Enable Time S to A or B tDIS Output Disable time S to A or B NOTE: 1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance when driven by an ideal voltage source (zero output impededance). 3 IDT74CBTLV16214 LOW-VOLTAGE 12-BIT 3:1 MUX / DEMUX BUS SWITCH INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS Symbol VCC(1)= 3.3V±0.3V VCC(2)= 2.5V±0.2V Unit VLOAD 6 2 x Vcc V VIH 3 Vcc V VT 1.5 Vcc / 2 V VLZ 300 150 mV VHZ 300 150 mV CL 50 30 pF SAME PHASE INPUT TRANSITION tPLH tPHL tPLH tPHL OUTPUT VIH VT 0V VOH VT VOL VIH VT 0V OPPOSITE PHASE INPUT TRANSITION Propagation Delay VLOAD VCC 500Ω Pulse(1, 2) Generator VIN CONTROL INPUT GND tPZL VOUT D.U.T. RT DISABLE ENABLE Open OUTPUT SWITCH NORMALLY CLOSED LOW tPZH OUTPUT SWITCH NORMALLY OPEN HIGH 500Ω CL Test Circuits for All Outputs SWITCH POSITION Switch VLOAD tPHZ/tPZH GND tPD Open tPHZ VT 0V Enable and Disable Times NOTES: 1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2ns. Test VLOAD/2 VT VLOAD/2 VOL + VLZ VOL VOH VOH -VHZ 0V NOTE: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. tPLZ/tPZL tPLZ VIH VT 0V 4 IDT74CBTLV16214 LOW-VOLTAGE 12-BIT 3:1 MUX / DEMUX BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION XXX XX CBTLV IDT XX Device Type Package Temp. Range CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 PV PA PF Shrink Small Outline Package Thin Shrink Small Outline Package Thin Very Small Outline Package 16214 Low-Voltage 12-Bit 3:1 Mux / Demux Bus Switch 74 –40°C to +85°C for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 5 for Tech Support: [email protected] (408) 654-6459