IDT IDT74CBTLV3861QG

IDT74CBTLV3861
LOW-VOLTAGE 10-BIT BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
LOW-VOLTAGE 10-BIT
BUS SWITCH
IDT74CBTLV3861
FEATURES:
DESCRIPTION:
•
•
•
•
•
•
The CBTLV3861 provides ten bits of high-speed bus switching with low
on-state resistance of the switch allowing connections to be made with
minimal propagation delay.
The device is organized as one 10-bit bus switch. When output enable
(OE) is low, the 10-bit bus switch is on and port A is connected to port B.
When OE is high, the switch is open and a high-impedance state exists
between the two ports.
To ensure the high-impedance state during power up or power down,
OE should be tied to VCC through a pullup resistor; the minimum value of
the resistor is determined by the current-sinking capability of the driver.
5Ω
Ω A/B bi-directional switch
Isolation under power-off conditions
Over-voltage tolerant
Latch-up performance exceeds 100mA
VCC = 2.3V - 3.6V, Normal Range
ESD > 2000V per MIL-STD-883, Method 3015;
> 200V using machine model (C = 200pF, R = 0)
• Available in QSOP and TSSOP packages
APPLICATIONS:
• 3.3V High Speed Bus Switching and Bus Isolation
FUNCTIONAL BLOCK DIAGRAM
A1
2
SW
SIMPLIFIED SCHEMATIC, EACH SWITCH
22
B1
A
A10
OE
11
SW
13
B
B10
23
OE
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
JUNE 2006
1
© 2006 Integrated Device Technology, Inc.
DSC-5741/5
IDT74CBTLV3861
LOW-VOLTAGE 10-BIT BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
ABSOLUTE MAXIMUM RATINGS(1)
PIN CONFIGURATION
Symbol
NC
A1
1
24
2
23
VCC
Max
Unit
VCC
SupplyVoltage Range
Description
–0.5 to +4.6
V
VI
Input Voltage Range
–0.5 to +4.6
V
128
mA
–50
mA
–65 to +150
°C
Continuous Channel Current
OE
IIK
Input Clamp Current, VI/O < 0
TSTG
Storage Temperature
A2
3
22
B1
A3
4
21
B2
A4
5
20
B3
A5
6
19
B4
A6
7
18
B5
A7
8
17
B6
A8
9
16
B7
A9
10
15
B8
A10
11
14
B9
GND
12
13
B10
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
FUNCTION TABLE(1)
Input
OE
L
H
QSOP / TSSOP
TOP VIEW
Operation
A Port = B Port
Disconnect
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
OPERATING CHARACTERISTICS, TA = 25°C(1)
Symbol
Parameter
VCC
Supply Voltage
VIH
High-Level Control Input Voltage
VIL
TA
Low-Level Control Input Voltage
Test Conditions
Min.
Max.
Unit
2.3
3.6
V
VCC = 2.3V to 2.7V
1.7
—
V
VCC = 2.7V to 3.6V
2
—
VCC = 2.3V to 2.7V
—
0.7
VCC = 2.7V to 3.6V
—
0.8
−40
85
Operating Free-Air Temperature
NOTE:
1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation.
2
V
°C
IDT74CBTLV3861
LOW-VOLTAGE 10-BIT BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Operating Conditions: TA = –40°C to +85°C
Symbol
Min.
Typ.(1)
Max.
Unit
VCC = 3V, II = –18mA
—
—
–1.2
V
Parameter
Test Conditions
VIK
Control Inputs, Data I/O
II
Control Inputs, Data I/O
VCC = 3.6V, VI = VCC or GND
—
—
±1
µA
Data I/O
VCC = 3.6V, VO = 0 or 3.6V, switch disabled
—
—
5
µA
VCC = 0, VI or VO = 0 to 3.6V
—
—
50
µA
IOZ
IOFF
ICC
ΔICC(2)
Control Inputs
CI
Control Inputs
CIO(OFF)
VCC = 2.3V
Typ. at VCC = 2.5V
RON(3)
VCC = 3.6V, IO = 0, VI = VCC or GND
—
—
10
µA
VCC = 3.6V, one input at 3V, other inputs at VCC or GND
—
—
300
µA
VI = 3V or 0
—
4
—
pF
VO = 3V or 0, OE = VCC
VI = 0
—
—
—
—
—
—
—
6
5
5
27
5
5
10
—
8
8
40
7
7
15
pF
IO = 64mA
IO = 24mA
IO = 15mA
IO = 64mA
IO = 24mA
IO = 15mA
VI = 1.7V
VI = 0
VCC = 3V
VI = 2.4V
Ω
NOTES:
1. Typical values are at VCC = 3.3V, +25°C ambient.
2. The increase in supply current is attributable to each current that is at the specified voltage level rather than VCC or GND.
3. This is measured by the voltage drop between the A and B terminals at the indicated current through the switch.
SWITCHING CHARACTERISTICS
VCC = 2.5V ± 0.2V
Symbol
tPD(1)
Parameter
Propagation Delay
VCC = 3.3V ± 0.3V
Min.
Max.
Min.
Max.
Unit
−
0.15
−
0.25
ns
1
4.5
1
4.2
ns
1
5
1
5
ns
A to B or B to A
tEN
Output Enable Time
OE to A or B
tDIS
Output Disable Time
OE to A or B
NOTE:
1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance driven by an ideal voltage source
(zero output impedance).
3
IDT74CBTLV3861
LOW-VOLTAGE 10-BIT BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
TEST CIRCUITS AND WAVEFORMS
SAME PHASE
INPUT TRANSITION
TEST CONDITIONS
Symbol
VCC(1)= 3.3V±0.3V
(2)
VCC = 2.5V±0.2V
Unit
VLOAD
6
2 x Vcc
V
VIH
3
Vcc
V
VT
1.5
Vcc / 2
V
VLZ
300
150
mV
VHZ
300
150
mV
CL
50
30
pF
500Ω
Pulse(1, 2)
Generator
tPHL
VIH
VT
0V
DISABLE
ENABLE
CONTROL
INPUT
GND
tPZL
VOUT
D.U.T.
RT
tPLH
Propagation Delay
Open
VIN
tPHL
OPPOSITE PHASE
INPUT TRANSITION
VLOAD
VCC
tPLH
OUTPUT
OUTPUT
SWITCH
NORMALLY CLOSED
LOW
tPZH
OUTPUT SWITCH
NORMALLY
OPEN
HIGH
500Ω
CL
tPLZ
VLOAD/2
VT
tPHZ
VT
0V
Test Circuits for All Outputs
Enable and Disable Times
DEFINITIONS:
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
NOTES:
1. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns.
2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2ns; tR ≤ 2.5ns.
SWITCH POSITION
Test
Switch
tPLZ/tPZL
VLOAD
tPHZ/tPZH
GND
tPD
Open
VIH
VT
0V
VOH
VT
VOL
4
VIH
VT
0V
VLOAD/2
VOL + VLZ
VOL
VOH
VOH -VHZ
0V
IDT74CBTLV3861
LOW-VOLTAGE 10-BIT BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
XXX
XX
IDT
XX
CBTLV
Device Type Package
Temp. Range
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
Q
QG
PG
PGG
Quarter-size Small Outline Package
QSOP - Green
Thin Shrink Small Outline Package
TSSOP - Green
3861
Low-Voltage 10-Bit Bus Switch
74
–40°C to +85°C
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
5
for Tech Support:
[email protected]