A-A-59416

INCH-POUND
A-A-59416B
24 November 2014
SUPERSEDING
A-A-59416A
9 May 2008
COMMERCIAL ITEM DESCRIPTION
INDUCTOR, CHIP, FIXED, HIGH SELF RESONANT FREQUENCY, SURFACE MOUNT
The General Services Administration has authorized the use of this
commercial item description (CID) for all federal agencies.
1. SCOPE. This CID covers the general requirements for an inductor. Inductors covered by this CID are
intended for commercial/industrial applications.
2. CLASSIFICATION. This CID uses a classification system which is included in the Part Identification
Number (PIN) as shown in the following example (see 7.1).
AA59416
CID number
-
001
K
S
Dash number
(see table I)
Inductance Tolerance
(see table II)
(Optional) Termination
finish (see table III)
3. SALIENT CHARACTERISTICS.
3.1 Interface and physical dimensions. Inductors supplied to this CID shall be as specified herein. (see
figure 1).
3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I.
3.3 Weight. The weight shall be no greater than 0.5 gram maximum.
3.4 Operating temperature range. The operating temperature range is –40C to +125C.
3.5 Temperature rise. DC current rating for a 15C rise.
3.6 Altitude. The maximum altitude is 70,000 feet.
3.7 Marking. Inductors supplied to this CID shall be marked with the manufacturer’s standard
commercial PIN.
3.8 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and
externally. Tin content of transformer components and solder shall not exceed 97 percent, by mass. Tin
shall be alloyed with a minimum of 3 percent lead, by mass.
3.9 Recycled, recovered, environmentally preferable, or biobased materials. Recycled, recovered,
environmentally preferable, or biobased materials should be used to the maximum extent possible,
provided that the material meets or exceeds the operational and maintenance requirements, and
promotes economically advantageous life cycle costs.
Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may
improve this document should be addressed to: DLA Land and Maritime, Columbus, ATTN: VAT, P.O.
Box 3990, Columbus OH 43218-3990, or email ([email protected] ). Since contact information can
change you may want to verify the currency of the address information using the ASSIST Online
database at https://assist.dla.mil.
AMSC N/A
FSC 5950
A-A-59416B
3.10 Workmanship. Inductors shall be processed in such a manner as to be uniform in quality and shall
be free from other defects that will affect life, serviceability, or appearance.
Dimension
Inches
mm
A Max.
.071
1.80
B Max.
.044
1.12
C Max.
.040
1.02
D Ref.
.015
0.38
E
.030
0.76
F
.013
0.33
G
.034
0.86
H
.040
1.02
I
.025
0.64
J
.025
0.64
NOTES:
1. Dimensions are in Inches.
2. Metric equivalents are listed for general information only.
FIGURE 1. Configuration and dimensions.
2
A-A-59416B
TABLE I. Electrical characteristics.
900 MHz
CID dash
number
AA59416-
Inductance(nH)
001**
1.6 @ 250 MHz
002**
1.7 GHz
1/
SRF Min
(GHz)
DCR
Max
(OHMS)
IDCMAX
(mA)
63
12.5
0.030
700
1.86
50
12.5
0.045
700
31
2.24
44
12.5
0.250
100
3.31
75
3.38
88
5.9
0.045
700
22
3.72
53
3.71
65
5.9
0.063
700
5, 3, 2
22
3.95
49
3.96
67
6.9
0.080
700
4.3 @ 250 MHz
5, 3, 2
22
4.32
50
4.33
70
5.9
0.063
700
008**
4.7 @ 250 MHz
5, 3, 2
20
4.72
47
4.75
57
5.8
0.116
700
009**
5.1 @ 250 MHz
5, 3, 2
20
4.93
47
4.95
56
5.7
0.140
700
010**
5.6 @ 250 MHz
5, 3, 2
26
5.77
63
6.05
80
4.76
0.075
700
011**
6.8 @ 250 MHz
5, 3, 2
27
6.75
60
7.10
81
5.8
0.110
700
012**
7.5 @ 250 MHz
5, 3, 2
28
7.70
60
7.82
65
4.8
0.106
700
013**
8.2 @ 250 MHz
5, 3, 2
30
8.25
82
8.37
87
4.2
0.115
700
014**
8.7 @ 250 MHz
5, 3, 2
28
8.86
62
9.32
58
4.6
0.109
700
015**
9.5 @ 250 MHz
5, 3, 2
28
9.7
59
9.92
61
5.4
0.135
700
016**
10 @ 250 MHz
5, 3, 2
31
10.0
66
10.6
83
4.8
0.130
700
017**
11 @ 250 MHz
5, 3, 2
30
11.0
53
11.5
56
4.0
0.130
700
018**
12 @ 250 MHz
5, 3, 2
35
12.3
72
13.5
83
4.0
0.130
700
019**
15 @ 250 MHz
5, 3, 2
35
15.4
64
16.8
89
4.0
0.170
700
020**
16 @ 250 MHz
5, 3, 2
34
16.2
55
17.3
52
3.3
0.170
700
021**
18 @ 250 MHz
5, 3, 2
35
18.7
70
21.4
69
3.1
0.170
700
022**
22 @ 250 MHz
5, 3, 2
38
22.8
73
26.1
71
3.0
0.190
700
023**
23 @ 250 MHz
5, 3, 2
38
24.1
71
28.0
67
2.85
0.190
700
024**
24 @ 250 MHz
5, 3, 2
36
24.5
45
28.7
39
2.65
0.190
700
025**
27 @ 250 MHz
5, 3, 2
40
29.2
74
34.6
65
2.8
0.220
600
026**
30 @ 250 MHz
5, 3, 2
37
31.4
47
39.9
28
2.25
0.220
600
027**
33 @ 250 MHz
5, 3, 2
40
36.0
67
49.5
42
2.3
0.220
600
028**
36 @ 250 MHz
5, 3, 2
37
39.4
47
52.7
24
2.08
0.250
600
029**
39 @ 250 MHz
5, 3, 2
40
42.7
60
60.2
40
2.2
0.250
600
030**
43 @ 250 MHz
5, 3, 2
38
47.0
44
64.9
21
2.0
0.280
600
031**
47 @ 200 MHz
5, 3, 2
38
52.2
62
77.2
35
2.0
0.280
600
032**
51 @ 200 MHz
5, 3, 2
35
55.5
69
82.2
34
1.9
0.270
600
033**
56 @ 200 MHz
5, 3, 2
38
62.5
56
97.0
26
1.9
0.310
600
034**
68 @ 200 MHz
5, 3, 2
37
80.5
54
168
21
1.7
0.340
600
035**
72 @ 150 MHz
5, 3, 2
34
82.0
53
135
20
1.7
0.490
400
Tolerance
(%)
Q
Min
L Typ
Q
Typ
L
Typ
Q
Typ
5
24
1.67
49
1.65
1.8 @ 250 MHz
5
16
1.83
35
003**
2.2 @ 250 MHz
5
13
2.22
004**
3.3 @ 250 MHz
5, 3, 2
35
005**
3.6 @ 250 MHz
5, 3, 2
006**
3.9 @ 250 MHz
007**
3
A-A-59416B
TABLE I. Electrical characteristics – continued.
900 MHz
1.7 GHz
Tolerance
(%)
Min
L Typ
Q
Typ
L
Typ
Q
Typ
SRF
Min
(GHz)
82 @ 150 MHz
5, 3, 2
34
96.2
54
177
21
037**
100 @ 150 MHz
5, 3, 2
34
124
49
--
038**
110 @ 150 MHz
5, 3, 2
32
138
43
039**
120 @ 150 MHz
5, 3, 2
32
166
040**
150 @ 150 MHz
5, 3, 2
28
041**
180 @ 100 MHz
5, 3, 2
042**
200 @ 100 MHz
043**
210 @ 100 MHz
044**
1/
DCR
Max
(OHMS)
IDCMAX
(mA)
1.7
0.540
400
--
1.4
0.580
400
--
--
1.35
0.610
300
39
--
--
1.3
0.650
300
250
25
--
--
.99
0.920
280
25
305
22
--
--
.99
1.25
240
5, 3, 2
25
--
--
--
--
.90
1.98
200
5, 3, 2
27
--
--
--
--
.895
2.06
200
220 @ 100 MHz
5, 3, 2
25
--
--
--
--
.90
2.10
200
045**
250 @ 100 MHz
5, 3, 2
25
--
--
--
--
.822
3.55
120
046**
270 @ 100 MHz
5, 3, 2
24
--
--
--
--
.90
2.30
170
047**
330 @ 100 MHz
5, 3, 2
25
--
--
--
--
.90
3.89
100
048**
390 @ 100 MHz
5, 3, 2
25
--
--
--
--
.90
4.35
100
CID dash number
AA59416-
Inductance(nH)
036**
Q
1/ DC current rating for a 15C rise.
TABLE II. Inductance tolerances
Code
Tolerance
(percentage)
G
2
J
5
K
10
TABLE III. Termination finish.
Code
Leave blank
Termination finish
Tin-lead
L
RoHS compliant, silver-palladium-platinum-glass-frit
T
RoHS, tin-silver-copper (95.5/4/0.5)
4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to
the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition
Regulation (FAR).
4
A-A-59416B
5. PRODUCT CONFORMANCE PROVISIONS
5.1 Product conformance. The products provided shall meet the salient characteristics of this CID,
conform to the producer’s own drawings, specifications, standards, and quality assurance practices, and
be the same product offered for sale in the commercial market. The Government reserves the right to
require proof of such conformance.
5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality
of the product to be provided under this CID:
a. The company producing the item must have been producing a product meeting the requirements
of this CID for at least 2 years.
b. The company must have sold 1,000 units meeting this CID in the commercial marketplace over
the past 2 years.
6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.
7. NOTES.
7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID.
See section 2 for PIN format example.
7.2 Environmentally preferable material. Environmentally preferable materials should be used to the
maximum extent possible to meet the requirements of this specification. As of the dating of this
document, the U.S. Environmentally Protection Agency (EPA) is focusing efforts on reducing 31 priority
chemicals. The list of chemicals is available on their website at
http://www.epa.gov/epaoswer/hazwaste/minimize/chemlist.htm. Further information is available at the
following EPA site: http://www.epa.gov/epaoswer/hazwaste/minimize/. Included in the EPA list of 31
priority chemicals are cadmium, lead, and mercury. Use of the materials on the list should be minimized
or eliminated unless needed to meet the requirements specified herein (see Section 3).
7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and
submission of these inductors to DSCC under the Military Parts Control Advisory Group (MPCAG)
evaluation program, CAGE code 58536 should be used.
7.4 Source of documents.
FEDERAL REGULATIONS
FAR
-
Federal Acquisition Regulations (FAR)
(Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from
the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401.)
7.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit
tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after
manufacture and can develop under typical operating conditions, on products that use such materials.
Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin
whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For
additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited
Coatings of Tin)
7.6 Ordering data. The contract or order should specify the following:
a. CID document number, revision, and CID PIN.
b. Product conformance provisions.
c. Packaging requirements.
5
A-A-59416B
7.7 Commercial products. As part of the market analysis and research effort, this CID was coordinated
with the following manufacturers of commercial products. At the time of CID preparation and
coordination, these manufacturers were known to have commercial products that would meet the
requirements of this CID. (NOTE: This information should not be considered as a list of approved
manufacturers or be used to restrict procurement to only the manufacturers shown.)
MFR's CAGE
02113
MFR's name and address
Coilcraft Inc
1102 Silver Lake Road
Cary, Illinois 60013-1658
Phone number (847) 639-2361
Uniform Resource Locator (URL): www.coilcraft.com
7.8 Part number (P/N) supersession data. This CID supersedes the following manufacturers' P/N's as
shown. This information is being provided to assist in reducing proliferation in the government inventory
system.
TABLE IV. P/N supersession data. 1/
CID dash number
(see table I)
AA59416001**
002**
003**
004**
005**
006**
007**
008**
009**
010**
011**
012**
013**
014**
015**
016**
017**
018**
019**
020**
021**
022**
023**
024**
Vendor commercial
PIN 2/
CAGE 02113
0603CS-1N6XJL*
0603CS-1N8XJL*
0603CS-2N2XJL*
0603CS-3N3X*L*
0603CS-3N6X*L*
0603CS-3N9X*L*
0603CS-4N3X*L*
0603CS-4N7X*L*
0603CS-5N1X*L*
0603CS-5N6X*L*
0603CS-6N8X*L*
0603CS-7N5X*L*
0603CS-8N2X*L*
0603CS-8N7X*L*
0603CS-9N5X*L*
0603CS-10NX*L*
0603CS-11NX*L*
0603CS-12NX*L*
0603CS-15NX*L*
0603CS-16NX*L*
0603CS-18NX*L*
0603CS-22NX*L*
0603CS-23NX*L*
0603CS-24NX*L*
CID dash number
(see table I)
AA59416025**
026**
027**
028**
029**
030**
031**
032**
033**
034**
035**
036**
037**
038**
039**
040**
041**
042**
043**
044**
045**
046**
047**
048**
Vendor commercial
PIN 2/
CAGE 02113
0603CS-27NX*L*
0603CS-30NX*L*
0603CS-33NX*L*
0603CS-36NX*L*
0603CS-39NX*L*
0603CS-43NX*L*
0603CS-47NX*L*
0603CS-51NX*L*
0603CS-56NX*L*
0603CS-68NX*L*
0603CS-72NX*L*
0603CS-82NX*L*
0603CS-R10X*L*
0603CS-R11X*L*
0603CS-R12X*L*
0603CS-R15X*L*
0603CS-R18X*L*
0603CS-R20X*L*
0603CS-R21X*L*
0603CS-R22X*L*
0603CS-R25X*L*
0603CS-R27X*L*
0603CS-R33X*L*
0603CS-R39X*L*
1/ When "*" is used for coded values, it’s the contractors responsibility to select those
options allowed by the CID.
2/ The manufacturer's P/N shall not be used for procurement to the requirements of this CID.
6
A-A-59416B
At the time of preparation of this CID, the aforementioned commercial products were
reviewed and could be replaced by the CID P/N shown.
7.9 Government users. To acquire information on obtaining these coils from the Government inventory
system, contact DLA Land and Maritime, ATTN: FMTC, Post Office Box 3990, Columbus, OH 432183990, or telephone (614) 692-7727.
7.10 Changes from previous issue. The margins of this CID are marked with asterisks to indicate where
changes from the previous issue were made. This was done as a convenience only and the Government
assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are
cautioned to evaluate the requirements of this document based on the entire content irrespective of the
marginal notations and relationship to the last previous issue.
MILITARY INTERESTS:
CIVIL AGENCY COORDINATING ACTIVITY:
GSA - 7FXE
Custodians:
Navy - EC
DLA - CC
Preparing Activity:
DLA - CC
Project 5950-2013-010
NOTE: The activities listed above were interested in this document as of the date of this document.
Since organizations and responsibilities can change, you should verify the currency of the information
above using the ASSIST Online database at https://assist.dla.mil .
7