A-A-59697

INCH-POUND
A-A-59697A
24 November 2014
SUPERSEDING
A-A-59697
1 October 2001
COMMERCIAL ITEM DESCRIPTION
COIL, RF, CHIP, FIXED, HIGH FREQUENCY
The General Services Administration has authorized the use of this
commercial item description (CID) for all federal agencies.
1. SCOPE. This CID covers the general requirements for a radio frequency coil. Coils covered by this CID are
intended for commercial/industrial applications.
2.
CLASSIFICATION. This CID uses a classification system which is included in the Part Identification Number
(PIN) as shown in the following example (see 7.1).
AA59697
CID number
-
001
F
T
Dash number (see
table I)
Inductance Tolerance
(see table II)
(Optional) Termination
finish (see table III)
3. SALIENT CHARACTERISTICS.
3.1 Interface and physical dimensions. Coils supplied to this CID shall be as specified herein. (see figure 1).
3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I.
3.3 Weight. The weight shall be no greater than 0.5 gram maximum.
3.4 Operating temperature range. The operating temperature range is –40C to +125C.
3.5 Temperature rise. DC current rating for 15C rise..
3.6
Altitude. The maximum altitude is 70,000 feet.
3.7 Marking. Coils supplied to this CID shall be marked with the manufacturer’s standard commercial PIN.
3.8 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin
content of transformer components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a
minimum of 3 percent lead, by mass.
3.9 Recycled, recovered, environmentally preferable, or biobased materials. Recycled, recovered,
environmentally preferable, or biobased materials should be used to the maximum extent possible,
provided that the material meets or exceeds the operational and maintenance requirements, and
promotes economically advantageous life cycle costs.
3.10 Workmanship. Coils shall be processed in such a manner as to be uniform in quality and shall be free from
other defects that will affect life, serviceability, or appearance.
Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this
document should be sent to: DLA Land and Maritime, Columbus, ATTN: VAT, P.O. Box 3990, Columbus OH
43218-3990, or email ([email protected] ). Since contact information can change you may want to verify the
currency of the address information using the ASSIST Online database at https://assist.dla.mil.
AMSC N/A
FSC 5950
A-A-59697A
Dimension
INCHES
MM
A
0.115 Max.
2.92 Max.
B
0.110 Max.
2.79 Max.
C
0.080 Max.
2.03 Max.
D
0.020 Ref.
0.51 Ref.
E
.0.080
2.03
F
0.020
0.51
G
0.060
1.52
H
0.100
2.54
I
0.040
1.02
J
0.050
1.27
NOTES:
1. Dimensions are in Inches.
2. Metric equivalents are listed for general information only.
3. Height Dimension “C” is before optional solder application. For maximum height dimension including solder,
add 0.006 in (0.152 mm).
4. Terminal wrap around is approximately 0.010 (0.25 mm).
FIGURE 1. Configuration and dimensions.
2
A-A-59697A
TABLE I. Electrical characteristics.
CID dash
number
AA59697-
Inductance
Tolerance
SRF min
(nH)
(%)
001**
10 @ 50 MHz
5, 2
50 @ 500 MHz
4100
.08
1000
002**
12 @ 50 MHz
5, 2
50 @ 500 MHz
3300
.09
1000
003**
15 @ 50 MHz
5, 2
50 @ 500 MHz
2500
.10
1000
004**
18 @ 50 MHz
5, 2
50 @ 350 MHz
2500
.11
1000
005**
22 @ 50 MHz
5, 2, 1
55 @ 350 MHz
2400
.12
1000
006**
27 @ 50 MHz
5, 2
55 @ 350 MHz
1600
.13
1000
007**
33 @ 50 MHz
5, 2
60 @ 350 MHz
1600
.14
1000
008**
39 @ 50 MHz
5, 2
60 @ 350 MHz
1500
.15
1000
009**
47 @ 50 MHz
5, 2, 1
65 @ 350 MHz
1500
.16
1000
010**
56 @ 50 MHz
5, 2, 1
65 @ 350 MHz
1300
.18
1000
011**
68 @ 50 MHz
5, 2, 1
65 @ 350 MHz
1300
.20
1000
012**
82 @ 50 MHz
5, 2, 1
60 @ 350 MHz
1000
.22
1000
013**
100 @ 25 MHz
5, 2, 1
60 @ 350 MHz
1000
.56
650
014**
120 @ 25 MHz
5, 2, 1
60 @ 350 MHz
950
.63
650
015**
150 @ 25 MHz
5, 2, 1
45 @ 100 MHz
850
.70
580
016**
180 @ 25 MHz
5, 2, 1
45 @ 100 MHz
750
.77
620
017**
220 @ 25 MHz
5, 2, 1
45 @ 100 MHz
700
.84
500
018**
270 @ 25 MHz
5, 2, 1
45 @ 100 MHz
600
.91
500
019**
330 @ 25 MHz
5, 2, 1
45 @ 100 MHz
570
1.05
450
020**
390 @ 25 MHz
5, 2, 1
45 @ 100 MHz
500
1.12
470
021**
470 @ 25 MHz
5, 2, 1
45 @ 100 MHz
450
1.19
470
022**
560 @ 25 MHz
5, 2, 1
45 @ 100 MHz
415
1.33
400
023**
620 @ 25 MHz
5, 2, 1
45 @ 100 MHz
375
1.40
300
024**
680 @ 25 MHz
5, 2, 1
45 @ 100 MHz
375
1.47
400
025**
750 @ 25 MHz
5, 2, 1
45 @ 100 MHz
360
1.54
360
026**
820 @ 25 MHz
5, 2, 1
45 @ 100 MHz
350
1.61
400
027**
910 @ 25 MHz
5, 2, 1
35 @ 50 MHz
320
1.68
380
028**
1000 @ 25 MHz
5, 2, 1
35 @ 50 MHz
290
1.75
370
029**
1200 @ 7.9 MHz
5, 2
35 @ 50 MHz
250
2.0
310
030**
1500 @ 7.9 MHz
5, 2
28 @ 50 MHz
200
2.3
330
031**
1800 @ 7.9 MHz
5, 2
28 @ 50 MHz
160
2.6
300
032**
2200 @ 7.9 MHz
5, 2
28 @ 50 MHz
160
2.8
280
033**
2700 @ 7.9 MHz
5, 2
22 @ 25 MHz
140
3.2
290
034**
3300 @ 7.9 MHz
5, 2
22 @ 25 MHz
110
3.4
290
Q min
(MHz)
DCR
Max
IDCMax
(mA)
(Ohms)
3
A-A-59697A
TABLE I. Electrical characteristics. - continued
CID dash
number
AA59697-
Inductance
Tolerance
SRF min
(nH)
(%)
035**
3900 @ 7.9 MHz
5, 2
20 @ 25 MHz
100
3.6
260
036**
4700 @ 7.9 MHz
5, 2
20 @ 25 MHz
90
4.0
260
037**
5600 @ 7.9 MHz
5
16 @ 7.9 MHz
20
4.0
240
038**
6800 @ 7.9 MHz
5
18 @ 7.9 MHz
40
4.9
200
039**
8200 @ 7.9 MHz
5
18 @ 7.9 MHz
25
6.0
170
Q min
(MHz)
DCR
Max
IDCMax
(mA)
(Ohms)
TABLE II. Inductance tolerances
Code
Tolerance
(percentage)
F
1
G
2
J
5
TABLE III. Termination finish.
Code
Leave blank
Termination finish
Tin-lead
L
RoHS compliant, silver-palladium-platinum-glass-frit
T
RoHS, tin-silver-copper (95.5/4/0.5)
4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the
maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).
5. PRODUCT CONFORMANCE PROVISIONS
5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the
producer’s own drawings, specifications, standards, and quality assurance practices, and be the same product
offered for sale in the commercial market. The Government reserves the right to require proof of such conformance.
5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality of the
product to be provided under this CID:
a.
The company producing the item must have been producing a product meeting the requirements of this CID
for at least 2 years.
b.
The company must have sold 1,000 units meeting this CID in the commercial marketplace over the past 2
years.
6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.
7. NOTES.
7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2
for PIN format example.
4
A-A-59697A
7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent
possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally
Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals is available on
their website at http://www.epa.gov/epaoswer/hazwaste/minimize/chemlist.htm. Further information is available at
the following EPA site: http://www.epa.gov/epaoswer/hazwaste/minimize/. Included in the EPA list of 31 priority
chemicals are cadmium, lead, and mercury. Use of the materials on the list should be minimized or eliminated unless
needed to meet the requirements specified herein (see Section 3).
7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of
these inductors to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code
58536 should be used.
7.4 Source of documents.
FEDERAL REGULATIONS
FAR -
Federal Acquisition Regulations (FAR)
(Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S.
Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401.)
7.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker
growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can
develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top
of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have
shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard
Specification for Electrodeposited Coatings of Tin).
7.6 Ordering data. The contract or order should specify the following:
a. CID document number, revision, and CID PIN.
b. Product conformance provisions.
c. Packaging requirements.
7.7 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the
following manufacturers of commercial products. At the time of CID preparation and coordination, these
manufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE: This
information should not be considered as a list of approved manufacturers or be used to restrict procurement to only
the manufacturers shown.)
MFR's CAGE
02113
MFR's name and address
Coilcraft Inc
1102 Silver Lake Road
Cary, Illinois 60013-1658
Phone number (847) 639-2361
Uniform Resource Locator (URL): www.coilcraft.com
5
A-A-59697A
7.8 Part number (P/N) supersession data. This CID supersedes the following manufacturers' P/N's as shown. This
information is being provided to assist in reducing proliferation in the government inventory system.
TABLE IV. P/N supersession data. 1/
CID dash number
(see table I)
AA59697-
Vendor commercial
PIN
CAGE 02113
2/
CID dash number
(see table I)
AA59697-
Vendor commercial
PIN
CAGE 02113
2/
001**
1008CS-100X*L*
021**
1008CS-471X*L*
002**
1008CS-120X*L*
022**
1008CS-561X*L*
003**
1008CS-150X*L*
023**
1008CS-621X*L*
004**
1008CS-180X*L*
024**
1008CS-681X*L*
005**
1008CS-220X*L*
025**
1008CS-751X*L*
006**
1008CS-270X*L*
026**
1008CS-821X*L*
007**
1008CS-330X*L*
027**
1008CS-911X*L*
008**
1008CS-390X*L*
028**
1008CS-102X*L*
009**
1008CS-470X*L*
029**
1008CS-122X*L*
010**
1008CS-560X*L*
030**
1008CS-152X*L*
011**
1008CS-680X*L*
031**
1008CS-182X*L*
012**
1008CS-820X*L*
032**
1008CS-222X*L*
013**
1008CS-101X*L*
033**
1008CS-272X*L*
014**
1008CS-121X*L*
034**
1008CS-332X*L*
015**
1008CS-151X*L*
035**
1008CS-392X*L*
016**
1008CS-181X*L*
036**
1008CS-472X*L*
017**
1008CS-221X*L*
037**
1008CS-562XJL*
018**
1008CS-271X*L*
038**
1008CS-682XJL*
019**
1008CS-331X*L*
039**
1008CS-822XJL*
020**
1008CS-391X*L*
1/
When "*" is used for coded values, it’s the contractors responsibility to select those options allowed by the
CID.
2/
The manufacturer's P/N shall not be used for procurement to the requirements of this CID.
At the time of preparation of this CID, the aforementioned commercial products were
reviewed and could be replaced by the CID P/N shown.
7.9 Government users. To acquire information on obtaining these coils from the Government inventory system,
contact DLA Land and Maritime, ATTN: FMTC, Post Office Box 3990, Columbus, OH 43218-3990, or telephone
(614) 692-7727.
7.10 Changes from previous issue. The margins of this CID are marked with asterisks to indicate where changes
from the previous issue were made. This was done as a convenience only and the Government assumes no liability
whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the
requirements of this document based on the entire content irrespective of the marginal notations and relationship to
the last previous issue.
6
A-A-59697A
MILITARY INTERESTS:
CIVIL AGENCY COORDINATING ACTIVITY:
GSA - 7FXE
Custodians:
Navy - EC
DLA - CC
Preparing Activity:
DLA - CC
Project 5950-2013-012
NOTE: The activities listed above were interested in this document as of the date of this document. Since
organizations and responsibilities can change, you should verify the currency of the information above using the
ASSIST Online database at https://assist.dla.mil .
7