A-A-59741

INCH-POUND
A-A-59741A
13 October 2014
SUPERSEDING
A-A-59741
25 October 2002
COMMERCIAL ITEM DESCRIPTION
INDUCTOR, POWER, SHIELDED, ULTRAMINIATURE,
SURFACE MOUNT
The General Services Administration has authorized the use of this
commercial item description (CID) for all federal agencies.
1. SCOPE. This CID covers the general requirements for a power inductor. Inductors covered by this
CID are intended for commercial/industrial applications.
2. CLASSIFICATION. This CID uses a classification system, which is included in the Part Identification
Number (PIN) as shown in the following example (see 7.1).
AA59741
CID number
-
001
Dash number
(see table I)
F
Inductance Tolerance
(see table II)
T
(Optional) Termination
finish (see table III)
3. SALIENT CHARACTERISTICS.
3.1 Interface and physical dimensions. Inductors supplied to this CID shall be as specified herein. (see
figure 1).
3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I.
3.3 Weight. The weight shall be no greater than 0.5 gram maximum.
3.4 Operating temperature range. The operating temperature range is –40C to +85C.
3.5 Temperature rise. DC current rating for a 30C rise.
3.6 Altitude. The maximum altitude is 70,000 feet.
3.7 Marking. Inductors supplied to this CID shall be marked with the manufacturer’s standard
commercial PIN.
3.8 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and
externally. Tin content of transformer components and solder shall not exceed 97 percent, by mass. Tin
shall be alloyed with a minimum of 3 percent lead, by mass.
3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or
environmentally preferable materials should be used to the maximum extent possible provided that the
material meets or exceeds the operational and maintenance requirements, and promotes economically
advantageous life cycle costs.
3.10 Workmanship. Coils shall be processed in such a manner as to be uniform in quality and shall be
free from other defects that will affect life, serviceability, or appearance.
Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may
improve this document should be addressed to: DLA Land and Maritime, Columbus, ATTN: VAT, P.O.
Box 3990, Columbus OH 43218-3990, or email ([email protected] ). Since contact information can
change you may want to verify the currency of the address information using the ASSIST Online
database at https://assist.dla.mil.
AMSC N/A
FSC 5950
A-A-59741A
Dimension
Inches
mm
Dimension
Inches
mm
A
.175 Max
4.45 Max
G
.090
2.29
B
.260 Max
6.60 Max
H
.055
1.40
C
.115 Max
2.92 Max
I
.160
4.06
D
.050
1.27
J
.270
6.86
E
.170
4.32
K
.140
3.56
F
.040
1.02
NOTES:
1. Dimensions are in Inches.
2. Metric equivalents (in parenthesis) are listed for general information only.
FIGURE 1. Configuration and dimensions.
2
A-A-59741A
TABLE I. Electrical characteristics.
CID dash
number
AA59741-
L
Q min
(H)
DCR Max
SRF typ
Current
(Ohms)
(MHz)
Max
(A)
001
1.0
30 @ 200 KHz
.040
250
1.4
002
1.5
30 @ 200 KHz
.045
125
.93
003
2.2
40 @ 200 KHz
.050
120
.92
004
3.3
40 @ 200 KHz
.055
120
.75
005
4.7
40 @ 200 KHz
.060
105
.58
006
6.8
40 @ 200 KHz
.065
50
.58
007
8.2
40 @ 200 KHz
.070
42
.47
008
10
40 @ 200 KHz
.075
38
.37
009
15
40 @ 100 KHz
.090
33
.31
010
22
40 @ 100 KHz
.11
25
.30
011
33
40 @ 100 KHz
.19
20
.30
012
47
40 @ 100 KHz
.23
20
.24
013
68
40 @ 100 KHz
.29
15
.17
014
100
40 @ 100 KHz
.48
10
.13
015
150
40 @ 100 KHz
.59
9
.10
016
220
40 @ 100 KHz
.77
6
.10
017
330
40 @ 100 KHz
1.4
5
.07
018
470
40 @ 100 KHz
1.8
4
.06
019
680
40 @ 100 KHz
2.2
3
.055
020
1000
40 @ 100 KHz
3.4
2
.045
021
1500
50 @ 100 KHz
4.2
2
.035
022
2200
50 @ 100 KHz
8.5
2
.028
023
3300
50 @ 100 KHz
11.0
1
.024
024
4700
50 @ 100 KHz
13.9
1
.021
025
6800
50 @ 100 KHz
25.0
1
.019
026
10000
50 @ 100 KHz
32.8
TABLE II. Inductance tolerances
Code
Tolerance
(percentage)
M
±20
3
.8
.017
A-A-59741A
TABLE III. Termination finish.
Code
Termination finish
Leave blank
Tin-lead
L
RoHS compliant, gold over nickel over moly-manganese
T
RoHS, tin-silver-copper (95.5/4/0.5)
4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to
the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition
Regulation (FAR).
5. PRODUCT CONFORMANCE PROVISIONS
5.1 Product conformance. The products provided shall meet the salient characteristics of this CID,
conform to the producer’s own drawings, specifications, standards, and quality assurance practices, and
be the same product offered for sale in the commercial market. The Government reserves the right to
require proof of such conformance.
5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality
of the product to be provided under this CID:
a. The company producing the item must have been producing a product meeting the requirements
of this CID for at least 2 years.
b. The company must have sold 1,000 units meeting this CID in the commercial marketplace over
the past 2 years.
6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.
7. NOTES.
7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID.
See section 2 for PIN format example.
7.2 Environmentally preferable material. Environmentally preferable materials should be used to the
maximum extent possible to meet the requirements of this specification. As of the dating of this
document, the U.S. Environmentally Protection Agency (EPA) is focusing efforts on reducing 31 priority
chemicals. The list of chemicals is available on their website at
http://www.epa.gov/epaoswer/hazwaste/minimize/chemlist.htm. Further information is available at the
following EPA site: http://www.epa.gov/epaoswer/hazwaste/minimize/. Included in the EPA list of 31
priority chemicals are cadmium, lead, and mercury. Use of the materials on the list should be minimized
or eliminated unless needed to meet the requirements specified herein (see Section 3).
7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and
submission of these inductors to DSCC under the Military Parts Control Advisory Group (MPCAG)
evaluation program, CAGE code 58536 should be used.
7.4 Source of documents.
FEDERAL REGULATIONS
FAR
-
Federal Acquisition Regulations (FAR)
(Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from
the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401.)
7.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit
tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after
manufacture and can develop under typical operating conditions, on products that use such materials.
Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin
whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For
additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited
Coatings of Tin).
4
A-A-59741A
7.6 Ordering data. The contract or order should specify the following:
a. CID document number, revision, and CID PIN.
b. Product conformance provisions.
c. Packaging requirements.
7.7 Commercial products. As part of the market analysis and research effort, this CID was coordinated
with the following manufacturers of commercial products. At the time of CID preparation and
coordination, these manufacturers were known to have commercial products that would meet the
requirements of this CID. (NOTE: This information should not be considered as a list of approved
manufacturers or be used to restrict procurement to only the manufacturers shown.)
MFR's CAGE
02113
MFR's name and address
Coilcraft Inc
1102 Silver Lake Road
Cary, Illinois 60013-1658
Phone number (847) 639-2361
Uniform Resource Locator (URL): www.coilcraft.com
7.8 Part number (P/N) supersession data. This CID supersedes the following manufacturers' P/N's as
shown. This information is being provided to assist in reducing proliferation in the government inventory
system.
TABLE IV. P/N supersession data. 1/
CID dash
number
(see table I)
AA59741-
Vendor commercial
PIN
CAGE 02113
2/
CID dash
number
(see table I)
AA59741-
Vendor commercial
PIN
CAGE 02113
2/
001
DS1608C-102ML*
014
DS1608C-104ML*
002
DS1608C-152ML*
015
DS1608C-154ML*
003
DS1608C-222ML*
016
DS1608C-224ML*
004
DS1608C-332ML*
017
DS1608C-334ML*
005
DS1608C-472ML*
018
DS1608C-474ML*
006
DS1608C-682ML*
019
DS1608C-684ML*
007
DS1608C-822ML*
020
DS1608C-105ML*
008
DS1608C-103ML*
021
DS1608C-155ML*
009
DS1608C-153ML*
022
DS1608C-225ML*
010
DS1608C-223ML*
023
DS1608C-335ML*
011
DS1608C-333ML*
024
DS1608C-475ML*
012
DS1608C-473ML*
025
DS1608C-685ML*
013
DS1608C-683ML*
026
DS1608C-106ML*
1/ When "*" is used for coded values, it’s the contractors responsibility to select those options
allowed by the CID.
2/ The manufacturer's P/N shall not be used for procurement to the requirements of this CID.
At the time of preparation of this CID, the aforementioned commercial products were
reviewed and could be replaced by the CID P/N shown.
5
A-A-59741A
7.9 Government users. To acquire information on obtaining these coils from the Government inventory
system, contact DLA Land and Maritime ATTN: FMTC, Post Office Box 3990, Columbus, OH 432183990, or telephone (614) 692-7727.
7.10 Changes from previous issue. The margins of this CID are marked with vertical lines to indicate
where changes from the previous issue were made. This was done as a convenience only and the
Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and
contractors are cautioned to evaluate the requirements of this document based on the entire content
irrespective of the marginal notations and relationship to the last previous issue.
MILITARY INTERESTS:
CIVIL AGENCY COORDINATING ACTIVITY:
GSA - 7FXE
Custodians:
Navy - EC
DLA - CC
Preparing Activity:
DLA - CC
Project 5950-2013-020
NOTE: The activities listed above were interested in this document as of the date of this document.
Since organizations and responsibilities can change, you should verify the currency of the information
above using the ASSIST Online database at https://assist.dla.mil .
6