XMC4200 Microcontroller Digital Power Control Card User Manual

XM C4 00 0
32-bit Microcontroller Series for Industrial Applications
XM C4 20 0 D ig it al P o w er C o ntr ol C ar d U ser
Ma nu al
UG_201511_PL30_003
Board User Manual
Scope and purpose
This document describes the features and hardware details of XMC4200 Digital Power Control Card,
designed to provide an evaluation platform for digital control applications with XMC ARM® Cortex™M4F based
microcontroller. This board is part of Infineon’s Digital Power Explorer Application Kit.
Applicable Products

XMC4200 Microcontroller

XMC Digital Power Explorer Kit

DAVE™
References (optional, may be shifted to Appendix)
Infineon: DAVE™, http://www.infineon.com/DAVE
Infineon: XMC Family, http://www.infineon.com/XMC
XMC Digital Power Explorer, http://www.infineon.com/xmc_dp_exp
Example codes for this board, www.infineon.com/DAVE
Customer Documentation
1
V1.1, 2016-02
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Table of Contents
Table of Contents
1
1.1
1.2
Overview.................................................................................................................... 3
Key Features ........................................................................................................................................ 3
Block Diagram ..................................................................................................................................... 3
2
2.1
2.2
2.3
2.3.1
2.3.2
2.4
2.5
2.6
2.7
Hardware Description.................................................................................................. 5
Power Supply ...................................................................................................................................... 5
Clock Generation ................................................................................................................................. 6
Debug Interface ................................................................................................................................... 6
Debug Connector Options ............................................................................................................ 7
Removing the On-Board Debugger .............................................................................................. 8
User LEDs and test points ................................................................................................................... 8
EEPROM ............................................................................................................................................... 9
Power Board Connector ...................................................................................................................... 9
Analog to Digital Converter (ADC) inputs filter................................................................................. 12
3
3.1
3.2
3.3
Production Data........................................................................................................ 14
Schematics ........................................................................................................................................ 14
Component Placement ..................................................................................................................... 19
Bill Material (BOM)............................................................................................................................. 19
4
Revision History........................................................................................................ 22
Board User Manual
2
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Overview
1
Overview
The XMC4200 Digital Power Control Card is an evaluation board with the goal to help engineers in the
learning and testing of digital power control applications. The board features a XMC4200 microcontroller
based on ARM® Cortex™M4F core.
The dimensions of the board (50 mm height, 45 mm width to connector) allow the usage of this evaluation
card into designs with high requirements on power density. In particular dimensions of XMC4200 Digital
Power Control Card are suitable for 1U rack designs. The control card integrates an isolated on board
debugger for plug and play experience. The isolated debugger part can be detached once the code is
finalized.
This board has been developed with the collaboration of Würth Elektronik whose passive components and
mechanical components are used.
1.1
Key Features
The XMC4200 Digital Power Control Card is equipped with the following features







Infineon XMC4200 (ARM® Cortex™-M4F-based) Microcontroller, 256 kByte on-chip Flash, LQFP64
Connection to power board like Digital Power Explorer, via the power board connector including analog
signals, PWM or serial interfaces
5 LEDs
− 1 Power indicating LED - “Power OK” from power board side
− 2 User LEDs (P2.2, P2.6)
− 2 Debugger controller LEDs (DEBUG, COM)
Isolated Debug options
− On-Board Debugger (SEGGER J-Link LITE) via USB connector
− ARM® Cortex™ 9 pin connector (1.27 mm pitch - double row) on non-isolated section. Isolation needs to
be built between this connector and the computer side to avoid overvoltage in computer.
Isolated Connectivity
− UART channel of On-Board Debugger (SEGGER J-Link LITE) via USB connector
Power supply of MCU domain
− Via power board connector (12V). Converted to 3.3V with Infineon supply parts
Power supply of isolated debug domain
− Via Debug USB connector
1.2
Block Diagram
Figure 1 shows the functional block diagram of the XMC4200 Digital Power Control Card. For more
information about the power supply domains please refer to chapter 2.1.
The control card has got the following building blocks:





1 Power Board Connector
1 I2C controlled EEPROM for optional data storage
2 User LED connected to GPIOs (P2.2 and P2.6)
2 user test points
USIC0 interface connector (P0.10, P0.14, P1.4, P1.5)
Isolated On-board Debugger via Debug USB connector (Micro-USB) with UART channel (USIC0, channel
0)
Board User Manual
3
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Overview
Optional ARM® Cortex™-Debug interface connector
XMC4200 Digital Power Control Card V1
Debug
USB
KIT_XMC42_DPCC_V1
GPIO
On-board
Debugger
XMC4200
2x test point
COMP+
DAC
ADC
isolation
EEPROM
USIC
I2C
U0C0
XMC4200
LQFP64
CCU80
USIC
USIC
U0C0
U1C0/C1
Debug
GPIO
SWD/SPD
3xCOMP
8X channels
8x PWM
2x channels
4x GPIO
Power Board Connector
2x user LED
GPIO

12V
BlockDiagram_XMC4200.emf
Figure 1
Block Diagram of XMC4200 Digital Power Control Card
Board User Manual
4
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
2
Hardware Description
The following sections give a detailed description of the hardware and how it can be used.
Test points
Isolated
domain
XMC4200
Microcontroller
Test LEDs
EEPROM
Power GND
Domain
USB connector
to PC
ADC inputs test
points
Debugger
controller –
XMC4200
ARM Cortex 9 pin
debugger connector
option
Galvanic
isolation IC
Power indicating
LED
Debug
Connector
options
Figure 2
2.1
Power supply
circuit
Split debugger
line
Power Board
Connector
Board_Interfaces_XMC42.emf
XMC4200 Digital Power Control Card hardware description
Power Supply
The XMC4200 Digital Power Control Cardboard is designed with two galvanically isolated supply domains.
On the left side, there is the debug domain or isolated domain, which contains a XMC4200 MCU as on-board
debug controller (OBD). The isolated domain is powered via the USB plug (5V)
The rest of the control card is called power GND supply domain. This part is supplied from the power board
connector and the control card will step down the input voltage to the 3.3V that XMC4200 requires. This
supply domain is usually powered from the power board connector. The typical current drawn by the drive
card at the power GND domain is about 65 mA at 12 V input voltage.
To indicate the power status of the power GND domain, one power indicating LED is provided on board (see
Figure 2). The LED will be “ON” when the corresponding power rail is powered.
LED Reference Power Rail
LED102
VDD3.3
Board User Manual
Voltage
3.3 V
5
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
Figure 3 shows details of the power supply concept of the control card. More detailed circuitry can be found
in section 3.1.
Digital Power Control Card XMC4200
KIT_XMC4200_DPCC_V1
IC302
IC103
IFX54441
VDD3.3ISO
VDD5ISO
IC301
VDD3.3
isolation
Debug
USB
IFX54441
UART
SWD
IFX90121
VDD
IC101
XMC4200
OBD
IC102
XMC4200
LQFP64
Power Board Connector
Power ok
LED
Power_Block_XMC4200.emf
Figure 3
2.2
Block Diagram of Power Supply Concept
Clock Generation
An external oscillator circuit is provided in the control card to provide a crystal signal. The internal PLL of
XMC4200 will trace care to generate all internal clocks needed in the microcontroller.
2.3
Debug Interface
The XMC4200 Digital Power Control Card supports 2 different debug interfaces:

Isolated On-Board Debugger (OBD). This is the default connection.
Connect to computer with an USB cable. The control card includes a debugger controller and isolation
up to 1kV to protect the computer. This is the easiest way and is supported by DAVETM and other
debuggers
The On-Board Debugger [1] supports
 Serial Wire Debug (SWD)

UART communication via a Virtual COM port
o
o
[1]
PC_RXD_DEV P1.5 USIC0CH0.DOUT0
PC_TXD_DEV P1.4 USIC0CH0.DX0B
Attention: The firmware of the on-board debugger requires the latest J-Link driver (V5.00 or higher) and
a Serial Port Driver (CDC driver) installed on your computer. Please check “Install J-Link Serial Port
Driver” when installing the latest J-Link driver (see Figure 4)
Board User Manual
6
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
Figure 4

Installation of J-Link Serial Port Driver
9 pin ARM® Cortex™ connector and an external galvanically isolated debugger hardware or “box”. This
option allows the user to utilize any ARM® Cortex™ debugger in the market. The user must make sure that
the debugger box used provides galvanic isolation (typically 1kV) to avoid damage due to high voltages
in the computer.
2.3.1
Debug Connector Options
XMC4200 Digital Power Control Card includes 3 connector options for debugging. The default configuration
of the control card is prepared for OBD debug and therefore, none for the 3 connector options are
assembled. If required, user has to mount the corresponding pin headers. The 3 connector options are:

Two 8 pins connector: OBD Debug Connector (X301) and Debug Connector (X102)– 2.54 mm header pitch

9pin ARM® Cortex™ (X101)– 1.27mm header pitch
Connectors are described in Figure 5
OBD Debug
Connector (8-pin)
Debug
Connector (8-pin)
SWCLK (TCK)
1
2
SWIO (TMS)
TCK
1
2
TMS
+3.3V
3
4
GND
+3.3V
3
4
GND
GND
5
6
+3.3V
GND
5
6
+3.3V
PC_TXD_DEV
7
8
P1.4
7
8
P1.5
PC_RXD_DEV
ARM Cortex 9 pin
connector
+3.3V
1
2
SWIO
GND
3
4
SWCLK
5
6
7
8
9
10
GND
GND
Debug_8pin_XMC4200.emf
Figure 5
Pin assignment of Debug Connector (8-pin)
Board User Manual
7
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
2.3.2
Removing the On-Board Debugger
XMC4200 Digital Power Control Card can be broken off into 2 parts by breaking the PCB as shown in Figure 6.
This will reduce the size of the main controller part so that it can fit into 1U standard sized rack systems once
programmed. The control card can still be debugged in 2 different ways if debugger part is removed (see
Figure 6):
1. connecting a ribbon cable to both 8 pin connectors (main controller part and debugger part) or,
2. using the 9 pin connector option with an external debugger box. If the board is not broken, this
connection cannot work.
Attention: when using external debuggers, make sure that the debugger box includes a galvanic
isolation to the computer. If the control card is exposed to high voltages, this could produce
damage to the computer
USB connector
to PC
COM and DBG LEDs
ARM Cortex 9 pin debugger
connector option
1
Debugger
controller –
XMC4200
2
1
8 pin debug
connector options
Figure 6
2.4
Split_debugger_XMC42.emf
Debug options when removing debugger part of control card
User LEDs and test points
The XMC4200 Digital Power Control Card provides a two user LEDs (P2.2 and P2.6). Next to the LEDs, two
test points (P2.0 and P2.1) are available in order to easily connect an oscilloscope’s probe for controlled
trigger signals.
Table 1
User LEDs
Board User Manual
8
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
User LEDs
Table 1
User LEDs
LED100
LED101
Connected to Port Pin
P2.2
P2.6
Attention: The test points are referenced to power GND supply domain. Hence they may carry
hazardous voltages.
2.5
EEPROM
XMC4200 Digital Power Control Card includes as well an external 4kB EEPROM for different purpose. This
EEPROM communicates with XMC4200 through I2C communication. XMC4200 can be configured as master
I2C for that purpose. This can be used for storing parameters for example.
Both data and clock lines are pulled up with 10 kohm resistors to 3.3V.
Sch_eeprom.emf
Figure 7
External EEPROM schematic
Table 2
Signal
EEPROM Chip Signal
XMC4200 port and channel
EEPROM_CLK
SCL
P2.4 - U0C1.SCLKOUT
EEPROM_DATA0
SDA
P2.5 - U0C1.DOUT0
2.6
Power Board Connector
The XMC4200 Digital Power Control Card provides a power board connector with a set of signals that can be
extensively used in power supply applications, from server power supplies to UPS or lighting power
supplies. Signals available in the connector are:

8 PWM signals

8 ADC analog inputs

3 comparator inputs

2 Serial channels

4 general purpose pins
Board User Manual
9
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
Sch_Power_Board_Connector.emf
Figure 8
Control card power connector schematic
Attention: The power board connector is also providing the power supply for the power GND supply
domain. Hence it may carry hazardous voltages.
As it can be seen in Figure 8, each signal entering XMC4200 Digital Power Control Card from the power board
connector is additionally protected by a bidirectional n ESD protection from Infineon.
XMC4200 has internal ESD protection in each pin, however, given the general purpose characteristic of this
control card, additional ESD protection is required to protect from very noisy power board environment that
could eventually damage the control card or the microcontroller in it.
The pin out of the connector is described in detail in Table 3.
Table 3
Power board connector pin out
Port in
Peripheral
Pin number Signal Name
XMC4200 function
1
GND
2
VDD
-
3
USIC2/GP5
P0.1
U1C1.DOUT0
4
USIC0
P0.11
U1C0.DX1A or
U1C0.SCLKOUT
5
USIC3/GP4
P0.0
U1C1.DX0D
6
USIC1
P2.14
U1C0.DOUT0 or
U1C0.DX0D
7
8
9
10
11
12
13
14
15
16
17
VDD3.3
GP0
CMP1OUT
GND
GND
CMP0OUT
CMP2OUT
GND
GND
GP1
PWM4
P1.3
P1.1
P1.0
P1.2
P1.8
P0.8
Board User Manual
Note
Digital GND
12V input from power board to control
card
Can be used as serial port or user port
pin
Can be used as serial port or user port
pin
3.3 V output to power board
User port pin
CSG.C1INA
Digital GND
Digital GND
CSG.C0INA
CSG.C2INA
Digital GND
Digital GND
User port pin
HROUT10
10
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
18
PWM0
Port in
XMC4200
P0.7
19
PWM5
P0.6
20
PWM1
P0.2
21
PWM6
P0.4
22
PWM2
P0.3
23
PWM7
P0.5
24
PWM3
P0.9
25
26
27
28
29
30
AGND
GP2
ADC4OUT
AGND
AGND
ADC0OUT
P0.10
P14.14
P14.6
31
ADC5OUT
P14.3
32
33
34
35
36
37
AGND
AGND
ADC1OUT
ADC6OUT
AGND
ADC7OUT
P14.5
P14.4
P14.0
38
ADC2OUT
P14.9
39
GP3
P2.7
Pin number Signal Name
40
ADC3OUT
P14.8
Peripheral
function
HROUT11
HROUT30 or
CCU80.OUT30
HROUT01 or
CCU80.OUT01
HROUT21or
CCU80.OUT10
HROUT20 or
CCU80.OUT20
HROUT00 or
CCU80.OUT00
HROUT31or
CCU80.OUT12
Note
Analog GND (ADC)
User port pin
VADC.G1CH6
Analog GND (ADC)
Analog GND (ADC)
VADC.G0CH6
VADC.G1CH3
or
VADC.G0CH3
Analog GND (ADC)
Analog GND (ADC)
VADC.G0CH5
VADC.G0CH4
Analog GND (ADC)
VADC.G0CH0
VADC.G1CH1
or DAC_OUT1
User port pin
VADC.G1CH0
or
DAC_OUT0
Given the flexible pin out in XMC4200, the functions above can be modified with SW configurations. In
Figure 9, the PWM options are depicted. The pin out is done to fully cover High Resolution PWM (HRPWM)
outputs. However, combinations of CCU8 and HRPWM are possible.
Several topologies in power supplies can be controlled with that pin out including LLC with synchronous
rectification, multi-phase buck/boost converters, PFC stages and much more.
Board User Manual
11
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
CCU80
Slice 0
CCU80.00 – PWM7 – P0.5
CCU80.01 – PWM1 – P0.2
CCU80
Slice 1
CCU80.10 – PWM6 – P0.4
HRC
Slice 1
HROUT10 – PWM4 – P0.8
HROUT11 – PWM0 – P0.7
CCU80.12 – PWM3 – P0.9
CCU80
Slice 2
CCU80.20 – PWM2 – P0.3
CCU80
Slice 2
CCU80.30 – PWM5 – P0.6
HRC
Slice 0
HROUT00 – PWM7 – P0.5
HROUT01 – PWM1 – P0.2
HRC
Slice 1
HROUT10 – PWM4 – P0.8
HROUT11 – PWM0 – P0.7
HRC
Slice 2
HROUT20 – PWM2 – P0.3
HROUT21 – PWM6 – P0.4
HRC
Slice 3
HROUT30 – PWM5 – P0.6
HROUT31 – PWM3 – P0.9
Option TRAP input
CCU80.INxA – TRAP Input for all CCU80 slices – P0.7
Timer options XMC4200.emf
Figure 9
PWM output options- top, using CCU8 - bottom using only HRPWM
Additionally to the pins in the power board connector, the microcontroller has pins connected internally.
Those are described in Table 3
Table 4
Signal Name
Port in XMC4200
Peripheral function
Note
User LED
User LED
I2C clock signal for
external EEPROM
I2C data signal for
external EEPROM
LED0
LED1
EEPROM_CLK
P2.2
P2.6
P2.4
U0C1.SCLKOUT
EEPROM_DATA0
P2.5
U0C1.DOUT0
2.7
Analog to Digital Converter (ADC) inputs filter
All ADC inputs in the control card are filtered with a high frequency cross-over frequency RC filter, as shown
in Figure 10. This will help to remove undesired high frequency noise from the input signals, and therefore,
will improve the measurement performance of the microcontroller
Board User Manual
12
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Hardware Description
Sch_ADC_filter.emf
Figure 10
ADC input RC filter schematic
With respect to the analog signals routed into XMC4200 ADC, a special plane is in place for increasing signal
integrity and best signal noise ratio. In Figure 11can be seen that VAGND plane has been layouted around all
ADC signals in all 4 layers of the PCB.
Sch_ADC_signal_layout_XMC4200.emf
Figure 11
ADC grounding layout detail
Both GND and AGND are connected together in a single point through a ferrite bead.
Board User Manual
13
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Production Data
3
Production Data
3.1
Schematics
This chapter contains the schematics for XMC4200 Digital Power Control Card
The board has been designed with Eagle. The full PCB design data of this board can also be downloaded
from www.infineon.com/xmc-dev.
Board User Manual
14
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Production Data
Sch_XMC42_0.emf
Figure 12
Schematic page 0: cover
Board User Manual
15
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Production Data
Sch_XMC42_1.emf
Figure 13
Schematic page1: MCU
Board User Manual
16
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Production Data
Sch_XMC42_2.emf
Figure 14
Schematic page 2: connector
Board User Manual
17
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Production Data
Sch_XMC42_3.emf
Figure 15
Schematic page 3: JLink &UART
Board User Manual
18
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Production Data
3.2
Component Placement
In Figure 16 the placement of some components is shown in a layout snapshot of the top layer of XMC4200
Digital Power Control Card
Lay_XMC42.emf
Figure 16
3.3
Layout top level view of XMC4200 Digital Power Control Card
Bill Material (BOM)
This board has been done in collaboration with Würth Elektronik. In Figure 17, the different components in
the board are shown. In Table 5 a complete bill of material is given.
Board User Manual
19
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Production Data
Ferrite
bead
Ceramic
capacitors
LDO
XMC4200
IFX54441LDV
Microcontroller
Ferrite bead
USB connector
to PC
IFX ESD
protections
Debugger
controller –
XMC4200
Ceramic
capacitors
LDO IFX54441LDV
Inductor
Infineon Component
Power supply:
IFX90121ELV50
Würth Elektronik
Component
Board_Components_XMC42.emf
Figure 17
Components from Infineon and Würth Elektronik
Table 5
Bill of Material List
No. Device / Description
Quantity Position
1
1
SN74LVC1G126DCKR SC70 SN74LVC1G126DCKR
IC304
2
ESD8V0L2B-03L Protect. Diode bi-dir ESD8V0L2B-03L IFX
13
3
4
5
CAT24AA04TDI-GT3 4k I2C EEPROM TSOT23-5
XMC4200 QFN-48 AB-Step XMC4200-Q48K256 AB step IFX
CPU XMC4200-F64K256 AB-Step LQFP-64
Si8662BB-B-IS1 Hex Isolator 4xIn / 2xOut 150MBit NB SOIC-16
SiLabs
SMD-LED SMD rt 0603 diffus 110mcd LSQ976-Z
SMD-LED SMD gn 0603 diffus 10mcd LGQ971-Z
Step-Down DC/DC 500mA 5.0Vout IFX90121ELV50 Infineon
SSOP-14
LDO IFX54441LDV Infineon TSON10 Vadj 300mA 1,8-20Vin
SMD-Quarz 12MHz 3.2x2.5mm 2Pad NX3225GB 12MHZ
SMD 2Pad
SMD Resistor 0R 1% 0603
SMD Resistor 33R 1% 0603
SMD Resistor 82K 1% 0603
1
1
1
D201, D202,D203,
D204,D205, D206, D207,
D208, D209, D210, D211,
D212, D302
IC100
IC301
IC101
1
IC303
2
3
LED101, LED302
LED100, LED102, LED301
1
IC102
2
IC103, IC302
2
Q102, Q301
2
2
2
R315, R316
R110, R111
R108, R304
6
7
8
9
10
11
12
13
14
Board User Manual
20
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Production Data
15
16
SMD Resistor 48K7 1% 0603
SMD Resistor 680R 1% 0402
2
4
17
SMD Resistor 10K 1% 0402 TK100
5
18
SMD Resistor 0R 0402
3
19
SMD Resistor 100R 1% 0402
8
20
21
22
23
24
25
2
2
1
1
2
3
1
Q101
27
SMD Resistor 4K7 1% 0402
SMD Resistor 1M 1% 0402
SMD Resistor 22K 1% 0402
SMD Resistor 560R 1% 0402
SMD Resistor 22R 1% 0402
SMD Resistor 510R 0402 1%
Quarz 32.768KHz, SMD 3.2x1.5 Cl 12,5pF NDK NX3215SA32.768K
SMD Capacitor 100p 5% X7R 0402 50V
R107, R303
R103, R104, R301, R302
R101, R102, R309, R311,
R312
R209, R210, R211
R201, R202, R203, R204,
R205, R206, R207, R208
R308,R105
R310, R314
R113
R109
R306, R307
R106, R112, R305
1
28
SMD-Capacitor 10uF 10V 0603 10%
6
29
SMD-Capacitor 4.7UF 35V 0805 10%
1
30
SMD Capacitor 15pF 10V 5% NP0 0402 Würth 885012005008
6
31
SMD-Capacitor 1nF 10% X7R 0402 50V Würth 885012205061
8
32
SMD Capacitor 10n 10% X7R 0402 16V Würth 885012205031
2
33
SMD Capacitor 100n X7R 0402 16V 10% Würth 885012205037 18
2
2
1
2
1
2
1
C103
C104, C107, C113, C114,
C115, C315
C102
C108, C109, C110, C111,
C302, C303
C201, C202, C203, C204,
C205, C206, C207, C208
C106, C314
C101, C105, C112, C116,
C117, C118, C119, C120,
C301, C305, C306, C308,
C309, C310, C311, C312,
C318, C319
C316, C317
C121, C307
C313
L101, L301
L103
D101, D301
X1
1
X302C
1
1
C304
JP301
1
X101
1
2
2
3
L100
JP2, JP3
X102, X301
C209, C210, C211
26
34
35
36
37
38
39
40
SMD Capacitor 1UF X5R 0402 10V 20% Würth 885012105012
SMD Capacitor 4u7F X5R 0603 10V 20% Würth 885012106012
SMD Capacitor 10UF X7R 0603 16V 10% Würth
Ferrite Bead 0603 60R 500mA Würth 74279267
SMD-Ferrite 10uH 1A 2828 Würth 744025100
Schottky Diode SOD323 low Vf BAS3010A-03W IFX 30V 1A
Pin header 2rows- 20-poles low profil 4mm
USB-connector Micro USB 2.0 Type AB - Horizontal Würth
41
629105150921
Not mounted components
42
SMD Capacitor 10n 5% X7R 0402 16V C0402C103J4R Kemet
43
Wrap header 1-row 5-poles
Pin header, 1,27, 2*5 pol SMD Pin7 ASP-166471-01 Samtec
44
Pin7 weg
45
Ferrite Bead 0603 60R 500mA Würth 74279267
46
Pin header 1-row 1-pole
47
Pin header 2-rows 4-poles
48
SMD-Capacitor 1nF 10% X7R 0402 50V Würth 885012205061
Board User Manual
21
V1.1, 2016-02
Customer Documentation
XMC4200 Digital Power Control Card User Manual
UG_201511_PL30_003
Revision History
4
Revision History
Current Version is V1.1, 2016-02
Page or Reference
Description of change
V1.0, 2015-10
Public version
V1.1, 2016-02
Table 3 corrections (USIC, PWM, ADC pins)
Board User Manual
22
V1.1, 2016-02
Customer Documentation
Trademarks of Infineon Technologies AG
µHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™,
DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™,
GaNpowIR™, HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™,
OPTIGA™, OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID
FLASH™, SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™
Trademarks updated November 2015
Other Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
www.infineon.com
Edition 2016-02
Published by
Infineon Technologies AG
81726 München, Germany
© 2016 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about this
document?
Email: [email protected]
Document reference
UG_201511_PL30_003
IMPORTANT NOTICE
The information given in this document shall in
no event be regarded as a guarantee of
conditions
or
characteristics
(“Beschaffenheitsgarantie”) .
With respect to any examples, hints or any typical
values stated herein and/or any information
regarding the application of the product, Infineon
Technologies hereby disclaims any and all
warranties and liabilities of any kind, including
without
limitation
warranties
of
noninfringement of intellectual property rights of any
third party.
In addition, any information given in this
document is subject to customer’s compliance
with its obligations stated in this document and
any applicable legal requirements, norms and
standards concerning customer’s products and
any use of the product of Infineon Technologies
in customer’s applications.
The data contained in this document is
exclusively intended for technically trained staff.
It is the responsibility of customer’s technical
departments to evaluate the suitability of the
For further information on the product, technology,
delivery terms and conditions and prices please
contact your nearest Infineon Technologies office
(www.infineon.com).
WARNINGS
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or any
consequences of the use thereof can reasonably be
expected to result in personal injury.