XMC1300 Digital Power Control Card User Manual

XM C1 00 0
32-bit Microcontroller Series for Industrial Applications
XM C1 30 0 D ig it al P o w er C o ntr ol C ar d U ser
Ma nu al
UG_201511_PL30_002
Board User Manual
Scope and purpose
This document describes the features and hardware details of XMC1300 Digital Power Control Card,
designed to provide an evaluation platform for digital control applications with XMC ARM® Cortex™M0 based
microcontroller. This board is part of Infineon’s Digital Power Control Application Kit.
Applicable Products

XMC1300 Microcontroller

XMC Digital Power Explorer Kit

DAVE™
References (optional, may be shifted to Appendix)
Infineon: DAVE™, http://www.infineon.com/DAVE
Infineon: XMC Family, http://www.infineon.com/XMC
XMC Digital Power Explorer, http://www.infineon.com/xmc_dp_exp
Example codes for this board, www.infineon.com/DAVE
Customer Documentation
1
V1.0, 2015-10
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Table of Contents
Table of Contents
1
1.1
1.2
Overview.................................................................................................................... 3
Key Features ........................................................................................................................................ 3
Block Diagram ..................................................................................................................................... 3
2
2.1
2.2
2.2.1
2.2.2
2.3
2.4
2.5
2.6
2.7
2.8
Hardware Description.................................................................................................. 5
Power Supply ...................................................................................................................................... 5
Debug Interface ................................................................................................................................... 6
Debug Connector Options ............................................................................................................ 7
Removing the On-Board Debugger .............................................................................................. 8
User LEDs and testpoints .................................................................................................................... 8
Power Board Connector ...................................................................................................................... 9
Comparator reference generation.................................................................................................... 11
Analog Comparator input filter option ............................................................................................. 13
Analog to Digital Converter (ADC) input filter .................................................................................. 14
Communication channel options ..................................................................................................... 14
3
3.1
3.2
3.3
Prodcution Data........................................................................................................ 16
Schematics ........................................................................................................................................ 16
Component Placement ..................................................................................................................... 20
Bill Material (BOM)............................................................................................................................. 20
4
Revision History........................................................................................................ 23
Board User Manual
2
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Overview
1
Overview
The XMC1300 Digital Power Control Card is an evaluation board with the goal to help engineers in the
learning and testing of digital power control applications. The board features a XMC1300 microcontroller
base on ARM® Cortex™M0 core.
The tiny dimensions of the board allow using this evaluation card into designs with high requirements on
power density. In particular the dimensions of XMC1300 Digital Power Control Card permit its usage in 1U
rack power supply designs. The control card integrates an isolated on board debugger for ease of usage that
can be removed once the code is finalized.
This board has been developed with the collaboration of Würth Elektronik whose passive components and
mechanical components are used.
1.1
Key Features
The XMC1300 Digital Power Control Card is equipped with the following features








Infineon XMC1300 (ARM® Cortex™-M0-based) Microcontroller, up to 200 kByte on-chip Flash, TSSOP38
Connection to power board like Digital Power Explorer, via the power board connector
USIC interface connector for connection of UART or PMBus™ (I2C)
4 LEDs
− 1 Power indicating LED- “Power OK” from power board side
− 1 User LEDs (P1.4)
− 2 Debugger controller LEDs (DEBUG, COM)
Isolated Debug options
− On-Board Debugger (SEGGER J-Link LITE) via USB connector
− ARM® Cortex™ 9 pin connector (1.27 mm pitch - double row) on non-isolated section. Isolation needs to
be built between this connector and the computer side to avoid overvoltage in computer.
Isolated Connectivity
− UART channel of On-Board Debugger (SEGGER J-Link LITE) via USB connector
Power supply of MCU domain
− Via power board connector (12V). Converted to 3.3V with Infineon supply parts
Power supply of isolated debug domain
− Via Debug USB connector
1.2
Block Diagram
Figure 1 shows the functional block diagram of the XMC1300 Digital Power Control Card. For more
information about the power supply domains please refer to chapter 2.1.
The control card is comprised of the following building blocks:
1 Power Board Connector
1 User LED connected to GPIOs (P1.4)
1 user test points (P1.4)
USIC0 CH0 interface to power board (P1.0, P1.1)
Isolated On-board Debugger via Debug USB connector (Micro-USB) with UART channel (USIC0, channel
0)
 Optional ARM® Cortex™-Debug interface connector





Board User Manual
3
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Overview
XMC1300 Digital Power Control Card V1
On-board
Debugger
XMC4200
Test point
GPIO
User LED
KIT_XMC13_DPCC_V1
CCU
(PWM DAC)
COMP
XMC1302
TSSOP38
isolation
+
ADC
CCU80
USIC
USIC
U0C1
U0C0
Debug
GPIO
SWD/SPD
RC Filters
3xCOMP
8X channels
8x PWM
2x channels
Power Board Connector
Debug
USB
4x GPIO
12V
BlockDiagram_XMC1300.emf
Figure 1
Block Diagram of XMC1300 Digital Power Control Card
Board User Manual
4
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
2
Hardware Description
The following sections give a detailed description of the hardware and how it can be used.
Test points
Test LEDs
XMC1300
Microcontroller
Isolated
domain
Power GND
Domain
USB connector
to PC
ADC
inputs test
points
Debugger
controller –
XMC4200
ARM Cortex 9
pin debugger
connector option
Galvanic
isolation IC
Power indicating
LED
Debug
Connector
options
Figure 2
2.1
Power supply
circuit
Power Board
Connector
Split debugger
line
Board_Interfaces_XMC13.emf
XMC1300 Digital Power Control Card hardware description
Power Supply
The XMC1300 Digital Power Control Cardboard is designed with two galvanically isolated supply domains.
On the left side, there is the debug domain or isolated domain, which contains a XMC1300 MCU as on-board
debug controller (OBD). The isolated domain is powered via the USB plug (5V)
The rest of the control card is called power GND supply domain. This part is supplied from the power board
connector and the control card will step down the input voltage to the 3.3V that XMC1300 requires. This
supply domain is usually powered from the power board connector. The typical current drawn by the drive
card at the power GND domain is about 18 mA at 12 V input voltage.
To indicate the power status of the power GND domain, one indicating LED is provided on board (see Figure
2). The LED will be “ON” when the corresponding power rail is powered.
LED Reference Power Rail
LED102
VDD3.3
Board User Manual
Voltage
3.3 V
5
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
XMC1300 Digital Power Control Card
KIT_XMC1300_DPCC_V1
Power ok
LED
IC302
IFX54441
IC303
VDD3.3ISO
VDD3.3
isolation
Debug
USB
VDD5ISO
IC301
XMC4200
OBD
IFX54441
IC101
UART
SWD
XMC1300
TSSOP38
VDD
Power Board Connector
Figure 3 shows details of the power supply concept of the control card. More detailed circuitry can be found
in section 3.1.
Power_Block_XMC1300.emf
Figure 3
2.2
Installation of J-Link Serial Port Driver
Debug Interface
The XMC1300 Digital Power Control Card supports 2 different debug interfaces:

Isolated On-Board Debugger (OBD). This is the default connection.
Connect to computer with an USB cable. The control card includes a debugger controller and isolation
up to 1kV to protect the computer. This is the easiest way and is supported by DAVETM and other
debuggers
The On-Board Debugger [1] supports
 Serial Wire Debug (SWD)

UART communication via a Virtual COM port
o
o
[1]
PC_RXD_DEV
PC_TXD_DEV
P1.2 USIC0CH0.DOUT0
P1.3 USIC0CH0.DX0A
Attention: The firmware of the on-board debugger requires the latest J-Link driver (V5.00 or higher)
and a Serial Port Driver (CDC driver) installed on your computer. Please check “Install J-Link Serial
Port Driver” when installing the latest J-Link driver (see Figure 4)
Board User Manual
6
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
Figure 4
Installation of J-Link Serial Port Driver
The On-Board Debugger can be accessed through the USB connector.
The Debug LED (LED301), named as DBG in the board, shows the status during debugging. The LED named
COM (LED302) signalizes the Virtual COM port communication with the computer.

9 pin ARM® Cortex™ connector and an external galvanically isolated debugger hardware or “box”. This
option allows the user to utilize any ARM® Cortex™ debugger in the market. The user must make sure that
the debugger box used provides galvanic isolation (typically 1kV) to avoid damage due to high voltages
in the computer.
2.2.1
Debug Connector Options
XMC1300 Digital Power Control Card includes 3 connector options for debugging. The default configuration
of the control card is prepared for OBD debug and therefore, none for the 3 connector options are
assembled. If required, user has to mount the corresponding pin headers. The 3 connector options are:

Two 8 pins connector: OBD Debug Connector (X301) and Debug Connector (X102)– 2.54 mm header pitch

9pin ARM® Cortex™ (X101)– 1.27mm header pitch
Connectors are described in Figure 5
OBD Debug
Connector (8-pin)
Debug
Connector (8-pin)
SWCLK
1
2
SWIO
P0.15
1
2
P0.14
+3.3V
3
4
GND
+3.3V
3
4
GND
GND
5
6
+3.3V
GND
5
6
+3.3V
PC_TXD_DEV
7
8
P1.3
7
8
P1.2
PC_RXD_DEV
ARM Cortex 9 pin
connector
+3.3V
1
2
SWIO
GND
3
4
SWCLK
GND
5
6
7
8
9
10
GND
Debug_8pin_XMC1300.emf
Figure 5
Pin assignment of Debug Connector (8-pin)
Board User Manual
7
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
2.2.2
Removing the On-Board Debugger
XMC1300 Digital Power Control Card can be broken off into 2 parts by breaking the PCB as shown in Error!
Reference source not found.. This will reduce the size of the main controller part so that it can fit into 1U
standard sized rack systems once programmed. The control card can still be debugged in 2 different ways if
debugger part is removed (see Figure 6):
1. connecting a ribbon cable to both 8 pin connectors (main controller part and debugger part) or,
2. using the 9 pin connector option with an external debugger box. If the board is not broken, this
connection cannot work.
Attention: when using external debuggers, make sure that the debugger box includes a galvanic
isolation to the computer. If the control card is exposed to high voltages, this could produce
damage to the computer
USB connector
to PC
COM and DBG LEDs
ARM Cortex 9 pin debugger
connector option
1
Debugger
controller –
XMC4200
2
1
8 pin debug
connector options
Remove_debugger_XMC13.e
mf
Debug options when removing debugger part of control card
Figure 6
2.3
User LEDs and test points
The XMC1300 Digital Power Control Card provides a two user LEDs (P1.4). Next to the LED there is a test
point (P1.4) available in order to easily connect an oscilloscope’s probe for controlled trigger signals. Both
the LED and the test point are together due to the limited number of pins available.
User LEDs
Table 1
User LEDs
LED101
Connected to Port Pin
P1.4
Attention: The test point is referenced to power GND supply domain. Hence they may carry hazardous
voltages.
Board User Manual
8
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
2.4
Power Board Connector
The XMC1300 Digital Power Control Card provides a power board connector with a set of signals that can be
extensively used in power supply applications, from server power supplies to UPS or lighting power
supplies. In summary, the signals available in the connector are:

8 PWM signals

8 ADC analog inputs

3 comparator inputs

2 serial channels

4 general purpose pins
Sch_Power_Board_Connector.emf
Figure 7
Control card power board connector schematic
Attention: The power board connector is also providing the power supply for the power GND supply
domain. Hence it may carry hazardous voltages.
As it can be seen in Figure 7, each signal entering XMC1300 Digital Power Control Card from the power board
connector is additionally protected by an ESD protection from Infineon.
XMC1300 has internal ESD protection in each pin, however, given the general purpose characteristic of this
control card, additional ESD protection is required to protect from very noisy power board environment that
could eventually damage the control card or the microcontroller in it.
The pin out of the connector is detailed in Table 2.
Table 2
Power board connector pin out
Pin
Port in
Signal Name
Peripheral function Note
number
XMC1300
1
GND
Digital GND
12V input from power board to control
2
VDD
card
U0C0.DOUT0 or
Can be used as serial port or user port
3
USIC2/GP5
P1.0
U0C0.DX0C
pin
The power board connector is per
Not
U0C1.SCLKOUT or default disconnected to permit
connected
4
USIC0
U0C1.DX1A
communication with Virtual COM port to
(P1.3)
computer (R113)
5
USIC3/GP4
P1.1
U1C1.DX0D
Can be used as serial port or user port
Board User Manual
9
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
Pin
Signal Name
number
Port in
XMC1300
Not
connected
(P1.2)
6
USIC1
7
8
VDD3.3
GP0
P0.8
9
CMP1OUT
P2.7
10
11
GND
GND
12
CMP0OUT
P2.9
13
CMP2OUT
P2.1
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
GND
GND
GP1
PWM4
PWM0
PWM5
PWM1
PWM6
PWM2
PWM7
PWM3
GND
GP2
ADC4OUT
GND
GND
ADC0OUT
31
ADC5OUT
32
33
GND
GND
34
ADC1OUT
P2.10
35
36
ADC6OUT
GND
P2.5
37
ADC7OUT
38
39
ADC2OUT
GP3
40
ADC3OUT
Board User Manual
Peripheral function Note
U0C1.DOU0 or
U0C1.DX0B
ACMP1.INP or/and
VADC.G1CH1
pin
The power board connector is per
default disconnected to permit
communication with Virtual COM port to
computer (R112)
3.3 V output to power board
User port pin
CMP1_INP - Through 0R resistor
Digital GND
Digital GND
P0.11
P0.1
P0.3
P0.4
P0.5
P0.6
P0.7
P0.0
P0.2
P0.12
P2.0
P2.3
P2.11
ACMP1.INP or/and
VADC.G0CH2
ACMP2.INP or/and
VADC.G0CH6
CMP0_INP - Through 0R resistor
CMP2_INP - Through 0R resistor
Digital GND
Digital GND
User port pin
CCU80.OUT01
CCU80.OUT03
CCU80.OUT13
CCU80.OUT12
CCU80.OUT11
CCU80.OUT10
CCU80.OUT00
CCU80.OUT02
VADC.G0CH5
VADC.G1CH5
VADC.G0CH4 or
ACMP.REF
Analog GND (ADC)
User port pin
ADC4 – Trough RC filter
Analog GND (ADC)
Analog GND (ADC)
ADC4 – Trough RC filter
ADC4 – Trough RC filter
Analog GND (ADC)
Analog GND (ADC)
Not
connected
(P2.6)
P2.4
Not
connected
(P2.2)
VADC.G0CH3 or
VADC.G1CH2
VADC.G1CH7
VADC.G0CH0
VADC.G1CH6
VADC.G0CH7
10
ADC4 – Trough RC filter
ADC4 – Trough RC filter
Analog GND (ADC)
CMP1_INN –Through 0R resistor. This
pin is default connected to CMP1_INN
ADC4 – Trough RC filter
User port pin
CMP2_INN –Through 0R resistor. This
pin is default connected to CMP2_INN
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
Given the flexible pin out in XMC1300, the functions above can be modified with SW configurations. InFigure
8, the PWM options are depicted. The pin out is done to fully cover High Resolution PWM (HRPWM) outputs.
However, combinations of CCU8 and HRPWM are possible.
Several topologies in power supplies can be controlled with that pin out including LLC with synchronous
rectification, multi-phase buck/boost converters, PFC stages and much more.
CCU80.00 – PWM7 - P0.0
CCU80.01 – PWM1 - P0.6
CCU80
Slice 0
CCU80.00 – PWM7 - P0.0
CCU80.01 – PWM4 - P0.1
CCU80.02 – PWM3 - P0.2
CCU80.03 – PWM0 - P0.3
CCU80
Slice 0
CCU80
Slice 1
CCU80.10 – PWM5 - P0.7
CCU80.11 – PWM1 - P0.6
CCU80.12 – PWM6 - P0.5
CCU80.13 – PWM2 - P0.4
CCU80
Slice 1
CCU80.00 – PWM7 - P0.0
CCU80.01 – PWM4 - P0.1
CCU40
Slice 0
CCU40.00 – PWM6 - P0.5
CCU40
Slice 1
CCU40.01 – PWM2 - P0.4
CCU40
Slice 2
CCU40.02 – PWM3 - P0.2
CCU40
Slice 3
CCU40.03 – PWM0 - P0.3
CCU80
Slice 0
CCU80
Slice 1
CCU80.10 – PWM5 - P0.7
CCU80.11 – PWM1 - P0.6
CCU80.10 – PWM3 - P0.2
CCU80.11 – PWM0 - P0.3
CCU80.12 – PWM6 - P0.5
CCU80.13 – PWM2 - P0.4
Timer options XMC1300.emf
Figure 8
PWM output options with CCU8 and CCU4
2.5
Comparator reference generation
XMC1300 includes 3 analog comparators that can be used for protections such as overcurrent or
overvoltage, but as well for valley detection or peak current control in sophisticated power conversion
systems.
Those comparators need a reference generation that is created from a PWM signal together with an on
board RC filter. The configuration for all 3 comparators and their reference generation is depicted into
Figure 9.
The RC filter used is a second order that provides better dynamic response and fewer ripple. The filter can be
configured by the user by exchanging the components of it to fit the specific requirements of the
application, for example, for a reference that needs to vary quickly, a smaller capacitor network is
necessary, however increasing output voltage ripple.
Board User Manual
11
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
XMC1300 Digital Power Control Card V1
Power
Board
Connector
XMC1302
TSSOP38
+
-
ACMP0
CCU40/3
+
-
ACMP1
CCU80/2
+
-
ACMP2
CCU80/3
INP(P2.9)
0R
INN(P2.8)
PWM_RC0 (P0.9)
PWM_RCx
0R
0R
CMP1
ADC3
0R
0R
CMP2
ADC7
PWM
RC filter
INP(P2.1)
INN(P2.2)
PWM_RC2 (P0.13)
INN
PWM
RC filter
INP(P2.7)
INN(P2.6)
PWM_RC1 (P1.5)
CMP0
PWM
RC filter
0R
Option not assembled
Signal not used
RC_Filter_XMC1300.emf
Figure 9
Comparator reference generation
XMC1300 Digital Power Control Card provides flexibility to implement different use cases. In Figure 10, two
important use cases are demonstrated.

Use case 1: more than 6 ADC channels are needed. In XMC1300, comparator inputs and ADC inputs can
be shared if required. In such case, the comparator reference and the comparator input signal can be
measured simultaneously with the ADC with up to 12 bits resolution.

Use case 2: the accuracy of a RC filter generated reference is limited even when using second order filter.
In some cases, a very accurate reference for the comparator might be critical for the system. In such
case, a reference signal can be connected from the power board side by assembling the corresponding
0R resistor and removing the RC filter connection to INN.
The signal in CMP2 will be compared to a high accuracy reference
Board User Manual
12
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
XMC1300 Digital Power Control Card V1
XMC1302
TSSOP38
Power
Board
Connector
ADC
ADC
ACMP1
INP(P2.7)
INN(P2.6)
+
-
CCU80/2
PWM_RC1 (P1.5)
0R
0R
CMP1
ADC7
Alternative usage 1:
More ADC channels
needed
Analog
signals
PWM
RC filter
Alternative usage 2:
High accuracy reference
for comparator needed
ACMP2
INP(P2.1)
INN(P2.2)
+
-
CCU80/3
0R
PWM_RC2 (P0.13)
0R
0R
CMP2
ADC7
PWM
RC filter
2.6
Fixed high accuracy
analog reference from
power board side
Option not assembled
RC_filter_XMC1300_use_cases.emf
Signal not used
Figure 10
Analog signal
Possible comparator use cases
Analog Comparator input filter option
Comparator input signals entering the control card from the power board connector, can be additionally
filtered with an RC filter option. As can be seen in Figure 11, there is a not assembled 0402 option
component. This is typically a capacitor. That filter can be used to reject high frequency noise in the
comparator input signal.
Comp_input_filter_option.emf
Figure 11
Comparator
filter option
Comparator input filter option- default not assembled
Board User Manual
13
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description
2.7
Analog to Digital Converter (ADC) input filter
All ADC inputs in the control card are filtered with a high frequency cross-over frequency RC filter, as shown
in Figure 12. This will help to remove undesired high frequency noise from the input signals, and therefore,
will improve the measurement performance of the microcontroller
ADC_input RC filter.emf
Figure 12
2.8
ADC input RC filter schematic
Communication channel options
XMC1300 Digital Power Control Card provides different communication paths to the power board side or to
the computer side through the OBD explained in section.
XMC1300 includes 2 independent serial channels that can be configured to work with different protocols
like I2C, UART or SPI. In order to support 2 channels into the power board with in many cases is necessary,
and at the same time to allow communication with the computer, XMC1300 Digital Power Control Card has
been prepared with or resistors to easily switch channels.
In Figure 13 the set up in XMC1300 Digital Power Control Card can be seen in detailed. The default
configuration is:


USIC0C0: UART through the OBD to the computer
o
P1.3 PC_TXD_DEV
o
P1.2PC_RXD_DEV
USIC0C1: general purpose serial channel to power board. For example for PMBusTM (pull ups must be
provided in the power board side)
o
P1.0 USIC2
o
P1.1USIC3
Optionally, by removing assembled resistors R114 and R115 (labeled as PC in Figure 13 and in silkscreen of
the board), and mounting R112 and R113 (labeled as PM), 2 general purpose channels are routed to the
power board, providing following configuration:

USIC0C0: general purpose serial channel to power board. For example for PMBusTM (pull ups must be
provided in the power board side)
o
P1.3 USIC0
o
P1.2USIC1
Board User Manual
14
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Hardware Description

USIC0C1: general purpose serial channel to power board. For example for PMBusTM (pull ups must be
provided in the power board side)
o
P1.0 USIC2
o
P1.1USIC3
XMC1300 Digital Power Control Card V1
Debug
USB
P1.0
P1.1
USIC
On-board
Debugger
XMC4200
U0C1
USIC2
USIC3
XMC1302
TSSOP38
USIC
U0C0
isolation
P1.3
PC_TXD_DEV
PC_RXD_DEV
0R
P1.2
0R
0R
USIC0
0R
PC
0R
PM
USIC1
Option not assembled
Signal not used
USIC circuit XMC1300.emf
Figure 13
Serial communication interfaces possible inXMC1300 Digital Power Control Card
Board User Manual
15
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Production Data
3
Production Data
3.1
Schematics
This chapter contains the schematics for XMC1300 Digital Power Control Card
The board has been designed with Eagle. The full PCB design data of this board can also be downloaded
from www.infineon.com/xmc-dev.
Sch_XMC13_0.emf
Figure 14
Schematic page 0: cover
Board User Manual
16
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Production Data
Sch_XMC13_1.emf
Figure 15
Schematic page1: MCU
Board User Manual
17
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Production Data
Sch_XMC13_2.emf
Figure 16
Schematic page 2: connector
Board User Manual
18
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Production Data
Sch_XMC13_3.emf
Figure 17
Schematic page 3: JLink &UART
Board User Manual
19
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Production Data
3.2
Component Placement
In Figure 18 the placement of some components is shown in a layout snapshot of the top layer of XMC1300
Digital Power Control Card
Lay_component_XMC13.emf
Figure 18
3.3
Layout and component placement top view of XMC1300 Digital Power Control Card
Bill Material (BOM)
This board has been done in collaboration with Würth Elektronik. In Figure 19, the different components in
the board are shown. In table 4 a complete bill of material is given.
Board User Manual
20
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Production Data
Ferrite
bead
Ceramic
capacitors
LDO
IFX54441LDV
XMC1300
Microcontroller
USB connector
to PC
IFX ESD
protections
Debugger
controller –
XMC4200
Ceramic
capacitors
Infineon Component
Würth Elektronik
Component
LDO IFX54441LDV
Board_Components_XMC13.emf
Figure 19
Table 3
Components from Infineon and Würth Elektronik
Bill of Material List
No.
Device / Description
Quantity Position
1
SN74LVC1G126DCKR SC70 SN74LVC1G126DCKR
1
IC304
2
ESD8V0L2B-03L Protect. Diode bi-dir ESD8V0L2B-03L IFX
15
3
4
1
1
1
IC303
2
1
2
LED101, LED302
LED102, LED301
IC103, IC302
1
Q301
10
11
12
13
XMC4200 QFN-48 AB-Step XMC4200-Q48K256 AB-step IFX
CPU XMC1302-T038X0200 AB Infineon
Si8662BB-B-IS1 Hex Isolator 4xIn / 2xOut 150MBit NB SOIC-16
SiLabs
SMD-LED SMD rt 0603 diffus 110mcd LSQ976-Z
SMD-LED SMD gn 0603 diffus 10mcd LGQ971-Z
LDO IFX54441LDV33 Infineon TSON10 300mA 1,8-20Vin
SMD-Quarz 12MHz 3.2x2.5mm 2Pad NX3225GB 12MHZ
SMD 2Pad
SMD Resistor 0R 1% 0603
SMD Resistor 33R 1% 0603
SMD Resistor 680R 1% 0402
SMD Resistor 10K 1% 0402 TK100
D201, D202,D203,
D204,D205, D206, D207,
D208, D209, D210, D211,
D212, D213, D214, D302
IC301
IC101
4
2
4
3
14
SMD Resistor 0R 0402
5
15
SMD Resistor 100R 1% 0402
6
R107, R303, R315, R316
R110, R111
R104, R109, R301, R302
R309, R3011, R312
R114, R115, R209, R210,
R211
R202, R203, R204, R206,
R207, R208
5
6
7
8
9
Board User Manual
21
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Production Data
16
SMD Resistor 1% 470R 0402
6
17
18
19
20
SMD Resistor 4K7 1% 0402
SMD Resistor 1M 1% 0402
SMD Resistor 22R 1% 0402
SMD Resistor 510R 0402 1%
SMD Capacitor 220nF 16V X7R 0603 10% Würth
885012206048
1
2
2
1
R212, R214, R215, R217,
R218, R220
R308
R310, R314
R306, R307
R305
2
C113, C121
21
22
SMD Capacitor 4n7 X7R 0402 16V 10% Würth 885012205029 6
23
24
25
SMD-Capacitor 47nF 10% X7R 0402 16V Würth
1
SMD-Capacitor 10uF 10V 0603 10%
2
SMD Capacitor 15pF 10V 5% NP0 0402 Würth 885012005008 2
26
SMD-Capacitor 1nF 10% X7R 0402 50V Würth 885012205061 9
27
SMD Capacitor 100n X7R 0402 16V 10% Würth
885012205037
SMD Capacitor 1UF X5R 0402 10V 20% Würth
885012105012
29
SMD Capacitor 10uF 0805 35V X5R
30
SMD-Capacitor 10uF 16V 0603 X5R
31
Ferrite Bead 0603 60R 500mA Würth 74279267
32
Schottky Diode SOD323 low Vf BAS3010A-03W IFX 30V 1A
USB-connector Micro USB 2.0 Type AB - Horizontal Würth
33
629105150921
34
Pin header 2-rows 20-poles low profil 4mm
Not mounted components
35
SMD Resistor 0R 0402
36
Pin header 1 row 1 pole
37
SMD Resistor 82K 1% 0603
38
SMD Resistor 0R 0402
39
SMD-Capacitor 47nF 10% X7R 0402 16V Würth
40
SMD Capacitor 10n 5% X7R 0402 16V C0402C103J4R Kemet
41
Pin header 1 row 5 poles
Pin header, 1,27, 2*5 pol SMD Pin7 ASP-166471-01 Samtec
42
Pin7 weg
43
Wrap-Leiste 2-reihig je 4-polig
44
SMD-Capacitor 1nF 10% X7R 0402 50V Würth 885012205061
28
Board User Manual
22
10
C212, C213, C214, C215,
C216, C217
C1
C107, C315
C302, C303
C106, C202, C203, C203,
C204, C205, C206,
C207,C314
C301, C305, C306, C308,
C309, C310, C311, C312,
C318, C319
3
C316, C317, C307
1
1
2
1
C102
C313
L101, L301
D301
1
X302
1
X200
2
1
2
2
1
1
1
R112, R113
JP2
R108, R304
R201, R205
C2, C3
C304
JP301
1
X101
1
3
X102, X301
C209, C210, C211
V1.0, 2015-10
Customer Documentation
XMC1300 Digital Power Control Card User Manual
UG_201511_PL30_002
Revision History
4
Revision History
Current Version is V1.0, 2015-10
Page or Reference
Description of change
V1.0, 2015-10
Public version
Board User Manual
23
V1.0, 2015-10
Customer Documentation
Trademarks of Infineon Technologies AG
µHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™,
DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™,
GaNpowIR™, HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™,
OPTIGA™, OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID
FLASH™, SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™
Trademarks updated November 2015
Other Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
www.infineon.com
Edition 2015-10
Published by
Infineon Technologies AG
81726 München, Germany
© 2015 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about this
document?
Email: [email protected]
Document reference
UG_201511_PL30_002
IMPORTANT NOTICE
The information given in this document shall in
no event be regarded as a guarantee of
conditions
or
characteristics
(“Beschaffenheitsgarantie”) .
With respect to any examples, hints or any typical
values stated herein and/or any information
regarding the application of the product, Infineon
Technologies hereby disclaims any and all
warranties and liabilities of any kind, including
without
limitation
warranties
of
noninfringement of intellectual property rights of any
third party.
In addition, any information given in this
document is subject to customer’s compliance
with its obligations stated in this document and
any applicable legal requirements, norms and
standards concerning customer’s products and
any use of the product of Infineon Technologies
in customer’s applications.
The data contained in this document is
exclusively intended for technically trained staff.
It is the responsibility of customer’s technical
departments to evaluate the suitability of the
For further information on the product, technology,
delivery terms and conditions and prices please
contact your nearest Infineon Technologies office
(www.infineon.com).
WARNINGS
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or any
consequences of the use thereof can reasonably be
expected to result in personal injury.