Datenblatt

HGXOHT OSCILLATOR
460 kHz to 50 MHz
High Shock, High Temperature Crystal Oscillator
DESCRIPTION
Statek’s HGXOHT crystal oscillator is a high temperature,
surface-mount oscillator that can survive extremely high
shocks _ up to 100,000 g. The design consists of a
hermetically-sealed high-shock crystal and a CMOS
compatible integrated circuit housed in a 5.0 mm x 7.5 mm
surface-mount ceramic package.
FEATURES
Mechanical shock survivability up to 100,000 g
High temperature operation up to 200OC
PACKAGE DIMENSIONS
Excellent stability over temperature
G
Fast start-up
High shock resistance
Designed for surface mount applications
CMOS and TTL compatible
Optional output Enable/Disable
A
2
3
1
4
D
F
TOP
Low EMI emission
D
Hermetically sealed ceramic package
B
APPLICATIONS
C
E
Industrial
Downhole instrumentation
Rotary shaft sensors
Underground boring tools
Avionics applications
SUGGESTED LAND PATTERN
TYPICAL
MAXIMUM
DIM
inches
mm
inches
mm
A
0.295
7.50
0.302
7.68
B
0.197
5.00
0.204
5.18
C*
0.089
2.25
0.098
2.50
D
0.055
1.40
-
-
E
0.040
1.02
-
-
F
0.240
6.10
-
-
G
0.100
2.54
-
-
*SM1 (Termination material is Au over Ni over W). Solder dip (SM3 and SM5) also
available.
PIN CONNECTIONS
1. Enable/Disable (E) or not connected (N)
2. Ground
3. Output
4. VDD
10208 Rev B
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications are typical at 25OC unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available, please contact factory.
Supply Voltage VDD
Supply Voltage
3.3 V ±10%
5.0 V ±10%
Calibration Tolerance
± 50 ppm, or tighter as required
Frequency Stability
Over Temperature1
Total Tolerance2
± 100 ppm for 25OC to 150OC
± 150 ppm for 25OC to 175OC
± 175 ppm for 25OC to 200OC
± 200 ppm for 25OC to 200OC
Output Load (CMOS)3
15 pF
Start-up Time
5 ms MAX
Rise/Fall Time
10 ns MAX
Duty Cycle
40% MIN, 60% MAX
Shock
survival4
Operating Temp
ENABLE/DISABLE OPTIONS (E/N)
Range6
E
N
When enabled (PIN 1 is high*)
20 g, 10-2000 Hz, swept sine
Output
Freq. output
Freq. output
-55ºC up to 200ºC
Oscillator
Oscillates
Oscillates
Current consumption
Normal
Normal
Output
High Z state
N/C
Oscillator
Stops
N/C
Current consumption
Very low
N/C
1. Does not include calibration tolerance.
2. Frequency over temperature relative to nominal frequency.
3. Higher CMOS loads available. Contact factory.
4. Shock survival applies at -55ºC to +125ºC.
5. Per MIL-STD-202G, Method 204D, Condition D, Random vibration testing also available.
6. Expected life at 200ºC is in excess of 1,500 hours.
PACKAGING OPTIONS
HGXOHT
Statek offers two enable/disable options: E and N. The Eversion has a Tri-State output and stops oscillating internally
when the output is put into the high Z state. The N-version
does not have PIN 1 connected internally and has no
enable/disable capability. The following table describes the
Enable/Disable option E.
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND N
Up to 100,000 g, 0.5 ms, ½ sine
Vibration, survival5
-0.5 V to 4.0 V (3.3V VDD)
-0.5 V to 7.0 V (5V VDD)
Storage Temperature
-55OC to +125OC
Maximum Process Temperature 260OC for 20 s
When disabled (PIN 1 is low)
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
- Tray Pack
- Tape and Reel
- 16 mm tape, 7” or 13” reels
Per EIA 481 (see Tape and Reel data
sheet # 10109)
N/C Pin 1 not connected, output frequency.
HOW TO ORDER HGXOHT SURFACE MOUNT CRYSTAL OSCILLATORS
HGXOHT
Supply Voltage
4 = 3.3V
5 = 5.0V
4
D
Shock Level
A = 5,000 g
B = 10,000 g
C = 20,000 g
D = 30,000 g
F = 50,000 g
G = 75,000 g
H = 100,000 g
S
Blank = Standard
S = Special or
custom
N
Enable/Disable
Option
E or N
Note: The HGXOHT oscillator with SM1 or SM5
termination is Pb free. The HGXOHT oscillator
with SM3 termination contains Pb.
SM3
20.0M
,
Termination
Blank = SM1
= Gold Plated (Pb Free)
SM3 = Solder Dipped
SM5 = Solder Dipped (Pb Free)
Frequency
K = kHz
M = MHz
/
Calibration
Tolerance
@ 250C
(in ppm)
/
200
/
Total Frequency
Tolerance (in
ppm)
Calibration
Tolerance
@ 250C
(in ppm)
Frequency
Stability over
Temp. Range
(in ppm)
OR
50
/
175
Frequency
Stability over
Temp. Range
(in ppm)
/
/
Total
Frequency
Tolerance
(in ppm)
H
Temp. Range:
H = 250C to 2000C
S = Customer
Specified Temp.
Range
H
Temp. Range:
H = 250C to
2000C
S = Customer
Specified Temp.
Range
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
10208 Rev B