ANEVAL_201602_PL16_017 55 W Flyback converter design using the IRS2982S controller IRXLED04 Authors: Peter B. Green About this document Scope and purpose The purpose of this document is to provide a comprehensive functional description and guide to using the IRS2982S control IC for LED and general purpose switch mode power supply (SMPS). The scope applies to all technical aspects that should be considered in the design process, including calculation of external component values, MOSFET selection, PCB layout optimization as well as additional circuitry that may be added if needed in certain cases. Intended audience Power supply design engineers, applications engineers, students. Table of Contents 1 Introduction ....................................................................................................................................... 2 2 IRS2982S functional overview ............................................................................................................ 3 3 3.1 3.2 Flyback converter............................................................................................................................... 4 Flyback converter types .......................................................................................................................... 4 Eval board specifications ........................................................................................................................ 5 4 Schematic .......................................................................................................................................... 6 5 Dimensioning ..................................................................................................................................... 7 6 Control loop ....................................................................................................................................... 9 7 Bill of materials ................................................................................................................................ 11 8 Transformer specification ................................................................................................................ 13 9 9.1 PCB Layout ....................................................................................................................................... 14 PCB layout guidelines for system optimization ................................................................................... 15 10 10.1 10.2 10.3 10.4 10.12 10.12.1 10.12.2 10.12.3 10.13 10.13.1 Test results....................................................................................................................................... 16 Operation at maximum load ................................................................................................................. 16 Test measurements under different line and load conditions ............................................................ 16 Start and steady state operation at maximum load ............................................................................ 21 Light load DCM operation ..................................................................................................................... 31 Thermal Performance under abnormal operating conditions ............................................................ 35 Open feedback loop (RFB1 removed), VCC supply connected ....................................................... 35 VCC supply removed (DVCC2 removed), feedback loop connected ................................................ 36 Reduced VCC supply (Support mode) ............................................................................................. 37 Line current harmonics according to EN61000-3-2 ............................................................................. 38 EMI Conducted Emissions (tested to CISPR22 limits) ..................................................................... 40 11 Conclusion ....................................................................................................................................... 42 Application Note www.infineon.com Please read the Important Notice and Warnings at the end of this document Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Introduction 1 Introduction The IRS2982S is a versatile SMPS controller IC primarily intended for LED drivers in the 5 to 100 W power ranges suitable for Buck, Buck-Boost and Flyback converters operating in critical conduction mode (CrCM) and discontinuous mode (DCM) at light loads. Flyback converters will be covered in this application note focusing on an isolated voltage regulated design with PFC. All of the control and protection required for the converter is integrated in the IRS2982S as well as a high voltage start-up cell to enable rapid illumination at switch on over a wide line input voltage range. The IRS2982S is also able to provide power factor correction in a single stage Flyback converter able to meet class C (lighting) line current harmonic limits of the EN61000-3-2 standard. A 55 W isolated voltage regulated PFC Flyback evaluation board based on the IRS2982S controller is described in detail in this application note and detailed test results are presented. Figure 1 IRXLED04 55 W Flyback evaluation board Application Note 2 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller IRS2982S functional overview 2 IRS2982S functional overview The IRS2982S is comprised of the following functional blocks: 1. High voltage start-up cell The IC internal functional blocks remain disabled in low power mode until VCC first rises above the VCCUV+ under-voltage lock out (UVLO) threshold, continuing to operate while VCC remains above VCCUV-. VCC is initially supplied through the integrated high-voltage start-up cell, which supplies a controlled current from the HV input provided a voltage greater than VHVSMIN, is present. The current supplied is limited to IHV_CHARGE reducing to less than IHVS_OFF when VCC reaches the cut-off threshold VHVS_OFF1. The HV start-up cell switches over from start-up mode to support mode after the feedback input at FB has exceeded VREG for the first time. In this mode the cut-off threshold becomes VHVS_OFF2. During steady state operation under all line-load conditions VCC is supplied through an auxiliary winding on the Flyback transformer with VCC high enough so that the HV start-up in does not supply current. If the auxiliary supply were unable to maintain VCC, the HV start-up cell operating in support mode would supply current to assist. 2. PWM controller The SMPS control section operates in voltage mode where the gate drive output on time is proportional to the error amplifier output voltage appearing at the compensation output COMP. An external capacitor CCOMP (shown in figure 3) connected to 0 V (ground) acts with the trans-conductance characteristic of the error amplifier to provide loop compensation and stability. Minimum on time is reached when VCOMP falls to VCOMPOFF below which the gate drive is disabled. Under very light load conditions VCOMP transitions above and below VCOMPOFF to produce burst mode operation. Off time is determined by the demagnetization signal received at the ZX input, which is derived from the auxiliary transformer winding that supplies VCC through a resistor divider. Internal logic limits the minimum off time to tOFFMIN, therefore the system transitions from CrCM to DCM at light loads. If the ZX input signal fails to provide triggering the next cycle will start automatically after a re-start period of tWD. 3. Protection The IRS2982S includes cycle by cycle primary over-current protection, which causes the gate drive to switch off if the voltage detected at the CS exceeds the threshold VCSTH. This prevents the possibility of transformer saturation at low line under heavy load but does not protect against output overload or short circuit. Over-voltage protection is also provided through the ZX input, which provides a voltage proportional to the output voltage. This disables the gate drive output and pulls the COMP voltage below the VCOMPOFF threshold. The error amplifier then starts to charge CCOMP until the gate drive starts up again at minimum on time. Under an open circuit output condition the over voltage protection causes the converter to operate in burst mode preventing the output voltage from rising too high. The IRS2982S uses an SO-8 package as shown below: HV VCC 8 FB 2 COMP 3 IRS2982 1 ZX 4 Figure 2 Application Note OUT 7 COM 6 CS 5 Pin 1 2 3 4 5 6 7 8 Name HV FB COMP ZX CS COM OUT VCC Description High Voltage Start-up Input Feedback Input Compensation and averaging capacitor input Zero-Crossing & Over-Voltage Detection input Current Sensing Input IC Power & Signal Ground Gate Driver Output Logic & Low-Side Gate Driver Supply IRS2982S pin assignments 3 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Flyback converter 3 Flyback converter 3.1 Flyback converter types There are several configurations of Flyback converter that may be used with the IRS2982S depending on the application. These can be classified according to isolation and regulation requirements as follows: 1. Isolated or non-isolated 2. Current or voltage regulation In the case of voltage regulation current limiting is needed for protection against overload or short circuit and in the case of current regulation over-voltage protection is necessary for an open-circuit. The IRS2982S can operate in any of the four combinations of (1) and (2). Extremely accurate current or voltage regulation is achieved in non-isolated converters since direct feedback to the FB input is possible. Isolation is however required in the majority of Flyback converters. For isolated constant current regulation an optoisolator is necessary; for isolated constant voltage regulation feedback may be taken from the auxiliary winding as shown in figure 3 with a small loss of line and load regulation accuracy. An opto-isolator is also necessary for highly accurate voltage regulation. The basic circuit in figure 3 shows the main elements of the IRS2982S based PFC Flyback converter. This can be used as a stand-alone power supply or as a front end stage with a current regulating Buck regulator as the back end stage in a dimmable (or non-dimmable) off line LED driver. This front end stage is able to provide a regulated output voltage over a wide range of line and load with sufficient accuracy for the majority of applications. DFB CSN RSN RVCC +VOUT DVCC T1 DSN CIN RFB1 BR1 HV IC1 2 COMP 3 ZX 4 IRS2982 FB AC Line Input VCC RZX1 8 CVCC 1 DZ CS OUT CVOUT ROUT 7 COM 6 CS 5 RG RFB2 CCOMP M1 RF RCS CF RZX2 CI Figure 3 -VOUT Isolated voltage regulated Flyback converter based on the IRS2982S A 55 W PFC Flyback voltage regulated design as implemented in the IRXLED04 evaluation board will be discussed in detail in the following sections. Application Note 4 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Flyback converter 3.2 Eval board specifications Input and output at normal operation: AC Input voltage 100 VAC up to 265 VAC (45 to 65 Hz) Output voltage 55 VDC Maximum output voltage ripple +/-3 V @ full load The tolerance of the nominal output voltage is +/-5% in the power range from 10% up to 100% of the rated output power. Maximum output continuous power 55 W PF >0.95 @50 W load and 230 VAC input voltage THD <10% @50% up to 100% load and < 20% @ 20% load with 230 VAC input voltage Efficiency >89% at 80% load and >88% at 100% load @ 230 VAC input voltage. Startup time to reach the secondary nominal output voltage of 55 VDC during full load condition and 230 VAC input voltage must be <300 ms. Protection features Primary output over-voltage protection @ VOUT <= 60 VDC Cycle by cycle primary over-current protection Attention: Output short circuit and overload protection are not provided on this evaluation board. This board can be damaged by sustained over loading or short circuiting the output! No load operation Burst mode during no load condition. Max power losses during no load condition must be <500 mW @230 VAC input voltage Max component temperature During worst case scenario (ambient temperature 60 °C) the max allowed component temperature is: Resistor < 105 °C Ceramic capacity, film capacity and electrolyte capacity <85 °C Flyback Transformer and chokes <105 °C MOSFET, transistor and diodes <105 °C IC <100 °C Dimension of evaluation board Max width 2.2” (55.9 mm), max length 4.4” (111.8 mm). Safety Requirements The single stage Flyback converter should cover the safety requirement regarding EN61347-2-13 and SELV max output voltage 60 VDC. This part of IEC 61347 specifies particular safety requirements for electronic control gear for use in DC supplies up to 250 V and AC supplies up to 1000 V at 50 Hz or 60 Hz and at an output frequency which can deviate from the supply frequency, associated with LED modules. Note: This evaluation board is designed as a front end stage for a two stage power supply such as an LED driver where the back end stage is a current regulating Buck regulator. The Flyback converter uses primary voltage regulation with no secondary current feedback and is therefore not designed to withstand a sustained overload or short circuit condition. Additional circuitry may be added if such protection is required. Application Note 5 Rev 1.1 2016-03-09 3 2 1 ACIN P1 S10K320E2K1 VR1 1.6A/300VAC L1 60mH/0.5A CX1 0.1uF/305V CY2 1nF/300VAC 1nF/300VAC 0.22uF/305V CX2 CY1 2 1 F1 3 4 3 1 1 COM2 Black 2 BR1 GBU4J-E3/51 COM1 Black 4 1 6 1 Application Note RZX2 14k 0.1uF/630V CDC 10k/0.5W RHV Yellow 1 ZX RZX1 47k 10nF CFB CZX 22pF CCMP1 22nF Yellow 1 COMP Output Voltage = 55V RFB2 20k Orange 1 FB RFB1 1M IRS2982 ZX COMP FB HV RCMP 330k CCMP2 0.22uF 4 3 2 1 IC1 RSNB1 470k CCF 1nF CS COM OUT VCC Red 1 VCC LL4148 DVCC1 5 6 7 8 RSNB2 470k 470 Orange RCF 1 10 RVCC1 CSNB 1nF/1kV RCS1 4.7 RG2 10k RG1 4.7 VCS RSNB3 470k RCS2 1.5 RCS3 1.5 MFB IPA80R650CE 1 White 1 GATE DSNB RS1MB 2 3 Figure 4 RCS4 1.5 T1 o 0.1uF CVCC1 CDS N/F 4 5 3o 2o 1 o o 8 7 10 9 12 11 DZ 18V 22uF/25V + CVCC2 LL4148 DVCC2 + 10uF CVB 510 COUT2 + COUT3 470uF/63V 1nF/300VAC CY3 470uF/63V RVCC2 470uF/63V COUT1 DOUT SBR20A300CT + COUT4 470uF/63V + VOUTBlack ROUT 15k 1 2 P2 OUT+ VOUT+ Red 1 4 1 VDC(HV) Red IRXLED04 55 W Flyback converter design using the IRS2982S controller Schematic Schematic IRXLED04 55 W PFC Flyback schematic Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Dimensioning 5 Dimensioning The IRXLED04 eval board is populated for basic voltage regulation from the transformer auxiliary winding as shown in figures 3 and 4. The Flyback converter is designed for power factor correction with low AC line current total harmonic distortion (iTHD). The MOSFET used is an IPA80R650CE 800 V rated CoolMOS device with 650 mΩ on resistance, 45 nC gate charge and low parasitic capacitances in a TO-220 FullPAK. This device is able to withstand high voltage ringing at switch off with minimal added snubber components and has low conduction and switching losses as well low gate drive current. The parameters of the MOSFET and output diode contribute to the overall high efficiency of the converter. The Flyback transformer (more accurately described as a coupled inductor) consists of three windings; the primary for energy storage during the on time, the secondary for energy transfer to the output during the off time and the auxiliary, which supplies VCC and provides the required de-magnetization and voltage feedback signals. The IRS2982S (IC1) VCC supply is derived from the transformer auxiliary winding through DVCC1 initially charging CVB then CVCC1 and 2 through RVCC and DVCC2 with DZ to clamp the voltage to protect IC1. Voltage feedback is provided through a divider comprised of RFB1 and RFB2, which sets the output voltage. The auxiliary winding voltage is proportional to the output voltage so that: 𝑉𝐴𝑈𝑋 = 𝑉𝑅𝐸𝐹 ∙ 𝑅𝐹𝐵1+𝑅𝐹𝐵2 𝑅𝐹𝐵2 𝑁 = 𝑉𝑂𝑈𝑇 ∙ 𝑁𝐴 [V] 𝑆 [1] Switching cycle peak current limiting is set by parallel shunt resistors RCS1 to 4, which give a combined resistance of 450 mΩ, setting the peak current to 2.67 A according to the threshold VCSTH of 1.2 V. This limits the inrush current during start-up and also protects against damage under over load or short circuit conditions. The eval board is not designed to withstand a sustained output overload or short circuit. The maximum peak current at low line and full load, assuming DMAX is 0.58 is calculated as: 𝐼𝑃𝑀𝐴𝑋 = 𝐷 2√2∙𝑃𝑂𝑈𝑇 𝑀𝐴𝑋 .𝑉𝐴𝐶𝑀𝐼𝑁 ∙𝜂 = 2√2∙50 0.58∙100∙0.9 [A] = 2.71 [2] The transformer turns-ratio is calculated as follows: 𝑁= 𝑁𝑃 𝑁𝑆 = √2∙𝑉𝐴𝐶𝑀𝐼𝑁 𝑉𝑂𝑈𝑇 +𝑉𝐹 𝐷 ∙ 1−𝐷𝑀𝐴𝑋 = 𝑀𝐴𝑋 0.58 √2∙100 ∙ 55+1 1−0.58 [3] = 3.49 The primary to auxiliary winding turns-ratio is calculated to provide an auxiliary supply voltage of 20 V: 𝑁𝑃 𝑁𝐴 =𝑉 √2∙𝑉𝐴𝐶𝑀𝐼𝑁 𝐴𝑈𝑋 +𝑉𝐹(𝐴𝑈𝑋) 𝐷 ∙ 1−𝐷𝑀𝐴𝑋 = 𝑀𝐴𝑋 0.58 √2∙100 ∙ 20+1 1−0.58 [4] = 9.3 The transformer primary inductance is calculated according to the formula: 𝐿𝑃𝑅𝐼 = 2 𝑉𝐴𝐶𝑀𝐼𝑁 ∙𝜂∙𝑁∙(𝑉𝑂𝑈𝑇 +𝑉𝐹 ) 2∙𝑃𝑂𝑈𝑇 ∙𝑓𝑀𝐼𝑁 ∙[𝑁∙(𝑉𝑂𝑈𝑇 +𝑉𝐹 )+√2∙𝑉𝐴𝐶𝑀𝐼𝑁 ] 1002 ∙0.9∙3.49∙(55+1) 2∙50∙65000∙[3.49∙(55+1)+√2∙100 ] [H] = 803 ∙ 10−6 H = 803 [5] [µH] Where, 𝜂 is the efficiency assumed to be 0.9 and minimum frequency set to 65 kHz to occur at the peak of the line input voltage at 100 Vrms. Application Note 7 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Dimensioning The resistor divider comprising RFB1 and RFB2 sets the output voltage according to: 𝑉𝑂𝑈𝑇 = 𝑁𝑃 𝑁𝐴 1 ∙ 𝑁 ∙ 𝑉𝑅𝐸𝐹 ∙ 𝑅𝐹𝐵1+𝑅𝐹𝐵2 𝑅𝐹𝐵2 [V] [6] In this design, RFB2=20 k and RFB1=1 M. VREF is 400 mV specified in the IRS2982S datasheet therefore: 1 9.3 ∙ 3.49 ∙ 0.4 ∙ 20𝑘+1000𝑘 20𝑘 [V] = 54.4 The threshold for over voltage protection through the ZX input is given by the resistor divider consisting of RZX1 and RZX2, where RZX1=47 k and RZX2=14 k and VOVTH is 5.1 V: 𝑉𝑂𝑈𝑇𝑂𝑉 = 𝑁𝑃 𝑁𝐴 ∙ 1 9.3 ∙ 3.49 ∙ 5.1 ∙ 1 𝑁 ∙ 𝑉𝑂𝑉𝑇𝐻 ∙ 47𝑘+14𝑘 14𝑘 𝑅𝑍𝑋1+𝑅𝑍𝑋2 𝑅𝑍𝑋2 [V] [7] [V] = 59.2 The maximum reflected voltage appearing at the MOSFET drain is then calculated as follows based on the highest AC line input voltage of 265 Vac: 𝑉𝐷𝑀𝐴𝑋 = √2 ∙ 𝑉𝐴𝐶𝑀𝐴𝑋 + (𝑉𝑂𝑈𝑇(𝑀𝐴𝑋) + 𝑉𝐹 ) ∙ 𝑁 [V] √2 ∙ 265 + (60 + 1) ∙ 3.49 = 588 [V] [8] It is recommended to allow 30% headroom on top of the reflected voltage to accommodate the switch off transient and high voltage ringing. This requires a MOSFET with a minimum drain-source maximum rating of 765 V and therefore an 800 V part has been selected. Four parallel 470 µF output capacitors (COUT1 to 4) have been used with a total capacitance of 1880 µF, combined ripple current rating of 8 A and impedance of 7 mΩ at 100 kHz. The maximum low frequency output ripple can be calculated as follows: 𝑉𝑅𝐼𝑃𝑃𝐿𝐸 = 2∙𝜋∙𝑓 𝐼𝑂𝑈𝑇 1 2∙𝜋∙45∙1880∙10−6 = 1.88 [Vpp] 𝑎𝑐(min) ∙𝐶𝑂𝑈𝑇 [Vpp] 𝐼𝑂𝑈𝑇 𝑎𝑐(min) ∙𝑉𝑅𝐼𝑃𝑃𝐿𝐸 [F] 𝐶𝑂𝑈𝑇 = 2∙𝜋∙𝑓 Application Note [9] 8 [10] Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Control loop 6 Control loop The voltage mode Flyback converter operating in critical conduction mode has a basic error amplifier to output voltage (VCOMP) transfer characteristic with a single pole of the form: 𝑉𝑂𝑈𝑇 (𝑠) 𝑉𝐶𝑂𝑀𝑃 (𝑠) ≈ 𝑘∙𝑓𝑠 𝐷 ∙ 1 1+ [11] 𝑠 𝜔𝑝𝑜 Where, 𝜔𝑝𝑜 = 𝑅 2 𝐿𝑂𝐴𝐷 ∙𝐶𝑂𝑈𝑇 , 𝑅𝐿𝑂𝐴𝐷 = 𝑉𝑂𝑈𝑇 𝐼𝑂𝑈𝑇 And 'k' is a constant of approximately 2.5 x 10-6 defined by the IRS2982S. To prevent over-shoot of the output voltage at start up while maintaining good regulation, power factor and line current THD a type 2 compensation network is used at the COMP pin, which is the output of the IRS2982S internal OTA error amplifier. The loop gain needs to cross 0 dB below the minimum line frequency with sufficient margin to achieve good PF/iTHD performance. VAUX Rupper VREF gm VCOMP Rlower CP R CZ Figure 5 Type 2 OTA compensation The transfer function has a zero at low frequency formed by R (RCMP) and CZ (CCMP2) and a pole at higher frequency formed by R and CP (CCMP1). The OTA gm is approximately 100 µΩ-1 as specified in the data sheet. The error amplifier transfer function is as follows: 𝑉𝐶𝑂𝑀𝑃 (𝑠) 𝑉𝐼𝑁 (𝑠) 𝑅𝐿𝑂𝑊𝐸𝑅. 𝑔𝑚. 𝑅 𝐿𝑂𝑊𝐸𝑅 +𝑅𝑈𝑃𝑃𝐸𝑅 ≈𝑅 1+ 1 𝑠𝑅𝐶𝑧 ∙ 1+𝑠𝑅𝐶 [12] 𝑝 The mid-band gain is given by: 𝐺𝑜 = 𝑅 𝑅𝐿𝑂𝑊𝐸𝑅. 𝑔𝑚 𝑅 [13] 𝐿𝑂𝑊𝐸𝑅 +𝑅𝑈𝑃𝑃𝐸𝑅 Application Note 9 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Control loop The zero is given by: 1 [14] 𝜔𝑧 = 𝑅.𝐶 𝑧 The pole is given by: 1 [15] 𝜔𝑝 = 𝑅.𝐶 𝑝 Figure 6 Bode plot showing gain and phase with type 2 compensation at full load, low line The red lines show the converter plant transfer function from VCOMP to VOUT and the blue lines show the feedback network and error amplifier transfer function. These are added together to give the loop transfer function T(s) shown by the dotted line. It can be seen that at maximum load the gain crosses zero dB at approximately 20 Hz and the phase margin is 87 °, which provides a stable system. Bode plots at different line and load conditions indicate that the system will always be stable. Application Note 10 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Bill of materials 7 Bill of materials Quantity Designator Manufacturer Part Number Value/Rating 1 BR1 Vishay GBU4J-E3/51 600 V/4 A 1 CCF TDK C2012X7R2E102K085AA 1 nF/250 V/0805/10% 1 CCMP1 TDK CGA4C2C0G1H223J060AA 22 nF/250 V/0805/10% 1 CCMP2 TDK C2012X7R1E224K125AB 0.22 µF/25 V/0805/10% 1 CDC Epcos B32922C3104M 0.1 µF/305 VAC/X2 1 CFB TDK C3216CH1H103K085AA 10 nF/50 V/1206/10% 1 COM1 Keystone 5001 0.04" dia black 1 COM2 Keystone 5001 0.04" dia black 1 COMP Keystone 5004 0.04" dia yellow 1 COUT1 Panasonic EEU-FR1J471B 470 µF/63 V/20% 1 COUT2 Panasonic EEU-FR1J471B 470 µF/63 V/20% 1 COUT3 Panasonic EEU-FR1J471B 470 µF/63 V/20% 1 COUT4 Panasonic EEU-FR1J471B 470 µF/63 V/20% 1 CSNB TDK C4532X7R3A102M200KA 1 nF/1 kV/20%/1812/X7R 1 CVB TDK C3216X5R1H106K160AB 10 µF/50 V/1206/10% 1 CVCC1 TDK C3216C0G1H104J160AA 0.1 µF/50 V/1206/5% 1 CVCC2 Panasonic EEU-EB1H220S 10 µF/50 V/1206/10% 1 CX1 Epcos B32922C3104M 0.1 µF/305 VAC/X2 1 CX2 Epcos B32922C3224M 0.22 µF/305 VAC/X2 1 CY1 Vishay VY2102M29Y5US63V7 1 nF/300 VAC/Y 1 CY2 Vishay VY2102M29Y5UG63V7 1 nF/300 VAC/Y 1 CY3 Vishay VY2102M29Y5US63V7 1 nF/300 VAC/Y 1 CZX Kemet C0805C220J5GACTU 22 pF/50 V/0805/5% 1 DOUT Diodes Inc SBR20A300CT 300 V/10 A/TO-220AB 1 DSNB Diodes Inc RS1MB-13-F 1000 V/1 A/SMB 1 DVCC1 Diodes Inc LL4148-13 75 V/0.15 A/MINIMELF 1 DVCC2 Diodes Inc LL4148-13 75 V/0.15 A/MINIMELF 1 DZ Micro Commercial Co BZV55C18-TP 18 V/0.5 W/MINIMELF 1 F1 Bussman SS-5H-1.6A-APH T1.6 A/300 VAC/4-8.5 1 IC1 Infineon IRS2982S SMPS Controller 1 IFB Keystone 5003 0.04" dia orange 1 L1 Kemet SS24H-R05600-CH 2x60 mH Common Mode 1 MFB Infineon IPA80R650CE 800 V/4.5 A/TO-220 1 P1 Phoenix Contact 1985205 3 Position 3.5mm Green 1 P2 Phoenix Contact 1985195 2 Position 3.5mm Green 1 1 Test results are based on this part. Application Note 11 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Bill of materials Quantity Designator Manufacturer Part Number Value/Rating 1 PFC Keystone 5002 0.04" dia white 1 RCF Panasonic ERJ-6GEYJ471V 470/0.125 W/0805/5% 1 RCMP Panasonic ERJ-6GEYJ334V 330 k/0.125 W/0805/5% 1 RCS1 Panasonic ERJ-8GEYJ4R7V 4.7/0.25 W/1206/5% 1 RCS2 Panasonic ERJ-8GEYJ1R5V 1.5/0.25 W/1206/5% 1 RCS3 Panasonic ERJ-8GEYJ1R5V 1.5/0.25 W/1206/5% 1 RCS4 Panasonic ERJ-8GEYJ1R5V 1.5/0.25 W/1206/5% 1 RFB1 Panasonic ERJ-8GEYJ105V 1 M/0.25 W/1206/5% 1 RFB2 Panasonic ERJ-8GEYJ203V 20 k/0.25 W/1206/5% 1 RG1 Panasonic ERJ-8GEYJ4R7V 4.7/0.25 W/1206/5% 1 RG2 Panasonic ERJ-8GEYJ103V 10 k/0.25 W/1206/5% 1 RHV Yageo CFR-50JB-52-10K 10 k/0.5 W/5% 1 ROUT Panasonic ERJ-8GEYJ153V 15 k/0.25 W/1206/5% 1 RSNB1 Panasonic ERJ-8GEYJ474V 470 k/0.25 W/1206/5% 1 RSNB2 Panasonic ERJ-8GEYJ474V 470 k/0.25 W/1206/5% 1 RSNB3 Panasonic ERJ-8GEYJ474V 470 k/0.25 W/1206/5% 1 RVCC1 Panasonic ERJ-8GEYJ100V 10/0.25 W/1206/5% 1 RVCC2 Panasonic ERJ-8GEYJ511V 510/0.25 W/1206/5% 1 RZX1 Panasonic ERJ-8GEYJ473V 47 k/0.25 W/1206/5% 1 RZX2 Panasonic ERJ-6ENF1402V 14 k/0.125 W/0805/1% 1 T1 Finepower Wurth TPT-PQ2627-001A 750316066 Rev 00 Flyback Transformer 800 µH 64:18:7 1 VCC Keystone 5000 0.04" dia red 1 VCS Keystone 5003 0.04" dia orange 1 VDC(HV) Keystone 5000 0.04" dia red 1 VOUT+ Keystone 5000 0.04" dia red 1 VOUT- Keystone 5001 0.04" dia black 1 VR1 Epcos S10K320E2K1 510 V/3.5 kA/10 mm 1 ZX Keystone 5004 0.04" dia yellow Application Note 12 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Transformer specification 8 Transformer specification Core type and material: Wurth 150-2239 PQ2625, PC44 Bobbin : THT, Vertical, Wurth p/n: 070-5649 Primary inductance and leakage inductance: Lp = 795µH (±5%), measured between pin1 and pin3, leakage inductance ≤ 10µH Start 3 11,12 5 9,10 2 Figure 7 End 2 9,10 4 7,8 1 No. of Turns 31 9 7 9 33 Wire Size 1 x φ0.4mm 2 x triple φ0.45mm 1 x φ0.32mm 2 x triple φ0.45mm 1 x φ0.4mm Layers ½ Primary ½ Secondary Flyback Auxiliary ½ Secondary ½ Primary Flyback transformer specification Application Note 13 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller PCB Layout 9 PCB Layout Figure 8 PCB top side components and traces Figure 9 PCB bottom side components and traces Application Note 14 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller PCB Layout 9.1 Figure 10 PCB layout guidelines for system optimization PCB layout The left side of the above figure shows the primary and secondary high frequency current loops surrounded by a black outline in each case. The primary loop on the left side of the board originates from CDC connecting first to the transformer (T1) primary (pin 1). The other side of the primary winding (pin 3) is connected to the drain of the MOSFET (MFB). To minimize EMI this trace should be kept as short as possible, however in this board due to the shape and the alternative DPAK footprint that has also been included, MFB could not be located directly next to T1. A ground plane has been placed on the other side of the PCB to absorb some of the EMI. The current sense resistors (RC1-4) are located such that the connection to the high frequency 0V bus return of CDC is extremely short with the other end connected to the source of MFC through another short trace. A pad connected to CDC 0V is provided so that a grounded heatsink may be used, provided the MOSFET is in an insulated TO-220 FullPAK. This also absorbs some of the EMI originating from the drain. The secondary high frequency current loop originates from T1 pins 11 and 12 connecting through a short trace to DOUT, which then connects through another very short trace to COUT1. The negative side of COUT1 returns directly back to T1 pins 7 and 8 again through another short trace providing the tightest possible HF current loop. Parallel output capacitors COUT2-4 are connected to COUT1 through very heavy Copper traces to provide minimum impedance and best possible HF ripple current sharing between the capacitors. A grounding pad is also provided for the DOUT heat sink. The diode must also be in a TO-220 FullPAK to use a grounded heatsink. The primary-secondary 0V Y capacitor (CY3) is connected directly to each 0V HF point with the shorted possible traces. The layout techniques described minimize EMI emitted by the converter as much as possible. Aside from EMI considerations, it is essential to design the PCB so that the IRS2982 is able to operate correctly without suffering from potential interference caused by noise or incorrect grounding. The picture on the right of the above figure shows the area around IC1. Pin 6 is the 0V (ground) connection, which is returned to the 0V side of CDC through a direct connection. It is also essential that decoupling capacitor CVCC1 be located directly next to IC1 with direct connections to the VCC and COM/0V pins. As in all switching power supplies, the signal and power grounds must be kept separate and join together only at the star point, which is at the negative side of the high frequency capacitor (CDC). Components associated with IC1 such as CCF, CZX CMP1 and RCMP are connected to the signal ground with the shortest traces possible back to pin 6. Additionally, clearance distances between high voltage traces and other parts of the circuit are kept as large as possible to comply with safety requirements. For this reason the middle leads of MFB and DOUT are bent forward to connect to a pad located further from the other two pads. Application Note 15 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10 Test results 10.1 Operation at maximum load The following measurements were made with IPA80R650CE MOSFET fitted as MFB. Table 1 Test result summary Parameter Unit Results VAC Vrms 100 120 230 265 Vdrain(ref) V 326 349 510 550 VCS_pk V 1.19 1.06 0.73 0.69 ICS_pk A 2.63 2.35 1.62 1.53 ton µs 16.00 12.03 4.39 3.68 toff µs 12.16 10.87 8.22 7.76 D ratio? 0.57 0.53 0.35 0.32 fs kHz 35.51 43.67 79.30 87.41 ZXmax V 4.7 4.7 4.7 4.7 10.2 Test measurements under different line and load conditions Table 2 Input 100 VAC Pout Vout Iout Pin [W] [V] [A] 100% 51.98 51.98 50% 26.39 20% Vout_rp [W] η [%] PF THD 1.00 57.79 89.95 0.993 5.60% 1.50 52.77 0.50 28.94 91.17 0.994 6.10% 0.75 10.80 54.02 0.20 12.10 89.29 0.981 8.70% 0.30 0.50% 2.80 56.09 0.05 3.67 76.42 0.855 n/a 0.08 0 0.00 59.30 0.00 0.68 0.00 n/a n/a 0.02 Vout Iout Pin η PF THD [%] Vout_rp Load Table 3 [Vpp] Input 120 VAC Load Pout [W] [V] [A] [W] [%] 100% 52.02 52.02 1.00 57.01 91.25 0.994 5.60 1.50 50% 26.43 52.85 0.50 28.81 91.72 0.992 6.10 0.75 20% 10.82 54.12 0.20 12.14 89.16 0.971 8.50 0.30 0.50% 2.82 56.38 0.05 3.81 73.99 0.802 n/a 0.08 0 0.00 59.20 0.00 0.63 0.00 n/a n/a 0.02 Application Note 16 [Vpp] Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Table 4 Input 230 VAC Pout Vout Iout Pin PF THD [%] Vout_rp [W] η [%] [W] [V] [A] 100% 52.19 52.19 1.00 56.09 93.05 0.983 9.10 1.50 50% 26.51 53.01 0.50 28.89 91.74 0.954 8.80 0.75 20% 10.83 54.17 0.20 12.51 86.60 0.825 15.40 0.30 0.50% 2.79 55.83 0.05 3.76 74.24 0.360 50.00 0.08 0 0.00 56.00 0.00 0.33 0.00 n/a n/a 0.02 Pout Vout Iout Pin η PF THD Vout_rp [W] [V] [A] [W] [%] [%] [Vpp] 100% 52.22 52.22 1.00 56.12 93.05 0.975 9.90 1.50 50% 26.52 53.04 0.50 29.00 91.45 0.929 9.90 0.75 20% 10.82 54.09 0.20 12.69 85.25 0.755 16.70 0.30 0.50% 2.78 55.53 0.05 3.61 76.91 0.267 50.00 0.08 0 0.00 55.70 0.00 0.31 0.00% n/a n/a 0.02 Load Table 5 [Vpp] Input 265 VAC Load Application Note 17 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Line Regulation DC Output Voltage 60,00 50,00 40,00 0.5% Load 30,00 20% Load 20,00 50% Load 10,00 100% Load 0,00 100 120 140 160 180 200 220 240 260 AC Input Voltage (RMS) Figure 11 Line regulation at different loads Load Regulation DC Output Voltage 60,00 50,00 40,00 100VAC 30,00 120VAC 20,00 230VAC 10,00 265VAC 0,00 0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 Load Current (A) Figure 12 Load regulation at different AC input voltage values Application Note 18 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Power Factor Power Factor 1,000 0,950 0,900 0,850 0,800 0,750 0,700 0,650 0,600 0,550 0,500 100VAC 120VAC 230VAC 265VAC 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 Output Current (A) Figure 13 Power factor vs load iTHD iTHD 50,0 45,0 40,0 35,0 30,0 25,0 20,0 15,0 10,0 5,0 0,0 100VAC 120VAC 230VAC 265VAC 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 Output Current (A) Figure 14 THDi vs load Application Note 19 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Efficiency Efficiency 100,00% 90,00% 80,00% 70,00% 60,00% 50,00% 40,00% 30,00% 20,00% 10,00% 0,00% 100VAC 120VAC 230VAC 265VAC 0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 Output Current (A) Efficiency Efficiency 100,00% 98,00% 96,00% 94,00% 92,00% 90,00% 88,00% 86,00% 84,00% 82,00% 80,00% 100VAC 120VAC 230VAC 265VAC 0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 Output Current (A) Figure 15 Efficiency vs load Application Note 20 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.3 Start and steady state operation at maximum load Figure 16 100 VAC steady state operation at 100% load Input current (yellow), CS (blue), VCC (red), VOUT ripple (green) Figure 17 100 VAC start-up at 100% load Input current (yellow), CS (blue), VCC (red), VOUT (green) Application Note 21 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Figure 18 230 VAC steady state operation at 100% load Input current (yellow), CS (blue), VCC (red), VOUT ripple (green) Figure 19 230 VAC start-up at 100% load Input current (yellow), CS (blue), VCC (red), VOUT (green) At both 120 VAC and 230 VAC with full load the output voltage rises within the specified time with minimal or no over-shoot. Cycle by cycle current limit operates for the first few AC line half-cycles limiting inrush current. Application Note 22 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.4 Start-up under different line and load conditions Figure 20 100 VAC start-up at 100% load Output voltage (yellow), VCOMP (red), VFB (green) Figure 21 120 VAC start-up at 100% load Output voltage (yellow), VCOMP (red), VFB (green) Application Note 23 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Figure 22 230 VAC start-up at 100% load Output voltage (yellow), VCOMP (red), VFB (green) Figure 23 265 VAC start-up at 100% load Output voltage (yellow), VCOMP (red), VFB (green) Application Note 24 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Figure 24 120 VAC start-up at 50% load Output voltage (yellow), VCOMP (red), VFB (green) Figure 25 120 VAC start-up at 20% load Output voltage (yellow), VCOMP (red), VFB (green) Application Note 25 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Figure 26 230 VAC start-up at 50% load Output voltage (yellow), VCOMP (red), VFB (green) Figure 27 230 VAC start-up at 20% load Output voltage (yellow), VCOMP (red), VFB (green) Application Note 26 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Figure 28 120 VAC start-up at 0% load Output voltage (yellow), VCOMP (red), VFB (green) Figure 29 265 VAC start-up at 0% load Output voltage (yellow), VCOMP (red), VFB (green) Application Note 27 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.5 Operation at line peak and zero crossing Figure 30 120 VAC at 100% load, AC line peak Gate drive (yellow), CS (blue), VZX (red), Vdrain (green) Figure 31 120 VAC at 100% load line zero-crossing Gate drive (yellow), CS (blue), VZX (red), Vdrain (green) Application Note 28 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Figure 32 230 VAC at 100% load line peak Gate drive (yellow), CS (blue), VZX (red), Vdrain (green) Figure 33 230 VAC at 100% load line zero-crossing Gate drive (yellow), CS (blue), VZX (red), Vdrain (green) Close to the line zero-crossing the amplitude of VZX is below the VZX+ threshold of 1.54 V so the next switching cycle is not started until the restart interval timeout period tWD. This does not significantly impact power factor and THD. Application Note 29 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.6 Burst mode operation at zero load Figure 34 120 VAC start-up at 0% load burst mode operation Gate drive (yellow), VCOMP (blue), VZX (red) Figure 35 230 VAC start-up at 0% load burst mode operation Gate drive (yellow), VCOMP (blue), VZX (red) Application Note 30 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.4 Figure 36 10.8 Figure 37 Light load DCM operation 100 VAC start-up at zero load Gate drive (yellow), VCOMP (blue), VZX (red), Vdrain (green) Over-voltage protection through ZX 265 VAC load step from 100% to 0% VOUT (yellow), Gate drive (blue), VCOMP (red), VZX (green) Application Note 31 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.9 High voltage start-up operation The high voltage start-up (HV pin) input current is measured with a 10 k resistor (RHV) connected from HV to the bus so that the oscilloscope traces in the following figures display approximately 1 mA/div: Figure 38 100 VAC start-up at 100% load HV start-up current (yellow), VFB (blue), VCC (red), Gate drive (green) Figure 39 265 VAC start-up at 100% load HV start-up current (yellow), VFB (blue), VCC (red), Gate drive (green) Application Note 32 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.10 High voltage start-up cell operation during zero load burst mode Figure 40 120 VAC start-up at 0% load HV start-up current (yellow), VFB (blue), VCC (red), Gate drive (green) Figure 41 230 VAC start-up at 0% load HV start-up current (yellow), VFB (blue), VCC (red), Gate drive (green) These waveforms show that in burst mode the auxiliary winding is able to supply VCC therefore the HV start-up cell support mode does not come into operation. Application Note 33 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.11 Thermal Performance under normal operating conditions Figure 42 100 VAC at 100% load (board top and bottom sides) Figure 43 265 VAC at 100% load (board top and bottom sides) Application Note 34 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.12 Thermal Performance under abnormal operating conditions 10.12.1 Open feedback loop (RFB1 removed), VCC supply connected The IRS2982S (IC1) reaches maximum case temperature at high line, 20% load. Temperature is measured in ambient of 25 °C. Figure 44 265 VAC at 20% load (IHV is 1 mA/div) VCC (yellow), VCOMP (blue), IHV (red), VOUT (green) Application Note 35 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Figure 45 10.12.2 265 VAC at 20% load, IRS2982S case temperature VCC supply removed (DVCC2 removed), feedback loop connected The IRS2982S (IC1) reaches maximum case temperature at high line, 20% load. Temperature is measured in ambient of 25 °C. Figure 46 265 VAC at 20% load (IHV is 1mA/div) VCC (yellow), VCOMP (blue), IHV (red), VOUT (green) Figure 47 265 VAC at 20% load, IRS2982S case temperature Application Note 36 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.12.3 Reduced VCC supply (Support mode) The IRS2982S (IC1) reaches maximum case temperature at high line, 20% load. Temperature is measured in ambient of 25 °C. VCC is supplied from an external supply maintained just above the UVLO threshold. Figure 48 265 VAC at 20% load (IHV is 1mA/div) VCC (yellow), VCOMP (blue), IHV (red), VOUT (green) Figure 49 265 VAC at 100% load, IRS2982S case temperature Application Note 37 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results 10.13 Table 1 Line current harmonics according to EN61000-3-2 EN61000-3-2 Class C limits for system power >25 W Percentage of Fundamental 120 VAC, 100% Load, Line Current Harmonics (%) 3,00E+01 2,50E+01 2,00E+01 1,50E+01 Harmonic (%) 1,00E+01 Limit 5,00E+00 0,00E+00 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Harmonic Figure 50 Harmonic test results at 120 VAC and 100% load Application Note 38 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Percentage of Fundamental 120 VAC, 50% Load, Line Current Harmonics (%) 3,00E+01 2,50E+01 2,00E+01 1,50E+01 Harmonic (%) 1,00E+01 Limits 5,00E+00 0,00E+00 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Harmonic Figure 51 Harmonic test results at 120 VAC and 50% load Percentage of Fundamental 230VAC, 100% Load, Line Current Harmonics (%) 3,00E+01 2,50E+01 2,00E+01 1,50E+01 Harmonic (%) 1,00E+01 Limit 5,00E+00 0,00E+00 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Harmonic Figure 52 Harmonic test results at 230 VAC and 100% load Application Note 39 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Percentage of Fundamental 230VAC, 50% Load, Line Current Harmonics (%) 3,00E+01 2,50E+01 2,00E+01 1,50E+01 Harmonic (%) 1,00E+01 Limit 5,00E+00 0,00E+00 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Harmonic Figure 53 Harmonic test results at 230 VAC and 50% load Class C limits are met at 50% and 100% loads at 120 VAC and 230 VAC. 10.13.1 Figure 54 EMI Conducted Emissions (tested to CISPR22 limits) Conducted emissions at 120 VAC and 100% load Application Note 40 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Test results Figure 55 Conducted emissions at 230 VAC and 100% load The red limit line shows the limit for the quasi-peak measurement, for which the frequency sweep trace is also shown in red. To pass the red trace must to remain below the red limit line and the pink average measurement trace must remain below the yellow average limit line. The orange peak trace may be disregarded. EMI emissions are very dependent on the board layout, please refer to section 9.1. Note: Infineon Technologies does not guarantee compliance with any EMI standard. Application Note 41 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Conclusion 11 Conclusion The specifications as listed in section 3.2 are met with efficiency exceeding 90% across the full line input voltage range from 50% to 100% load. Power factor remains above 0.95 at 120 VAC and 230 VAC nominal inputs from 50% load to 100%. The input current total harmonic distortion (iTHD) remains below 10% from 20% to 100% load over at 120 VAC input and from 70% to 100% load at 230 VAC, remaining below 20% down to 20% load from 100 to 265 VAC. At lighter loads power factor falls and iTHD increases, however output voltage regulation remains tight. Output voltage ripple at twice the AC line frequency remains 1.6 Vpp at full load at 60 Hz independent of the input voltage, which matches the calculated value from equation (10). Type 2 compensation of the operational trans-conductance error amplifier (OTA) provides tight load regulation from 10% to 100% load with a small increase below 10%. The output voltage rises to its operating level in less than 300 ms with no overshoot from 100 VAC to 265 VAC with only minimal overshoot at 100 VAC over the full load range. Performance indicates an over-damped control loop corresponding to the phase margin determined in section 6. The type 2 control loop compensation network successfully controls the startup and settling response while providing high power factor and low iTHD over a wide line/load range, which is able to meet EN61000-3-2 class C requirements for lighting apparatus. Over voltage protection as detected through the ZX input operates correctly to limit the output voltage under open and very light load conditions. Operation in DCM and burst mode are also seen to maintain output voltage regulation where necessary. Cycle by cycle primary over current protection operates correctly at start-up to limit inductor current and stress of the MOSFET. Operating waveforms confirm the calculated peak current value from section 5. Thermal performance under normal operating conditions (measured in open air at 25 degrees C ambient) as shown in section 10.11, indicates a temperature rise of 45°C at the transformer windings, however the cores remain at a lower temperature. The input bridge (BR1) operates component at low line with a rise of 33°C with a greatly reduced temperature rise at high line of 23°C. The MOSFET (MFB) has a 37°C rise at low line and a 24°C rise at high line due to higher primary peak current at low line for the IPA80R650CE measured with no heatsink attached. Under all normal conditions the high voltage start-up cell is deactivated as the feedback loop closes and it switches over from start-up mode to support mode. The HV cell allows the power supply to start up rapidly at any line input voltage, meeting the maximum specification of 300 ms from switch on to reaching nominal output voltage. Standy power is composed of the power dissipated in the output resistor ROUT and the power consumed by the controller IC VCC supplying the MOSFET gate drive during burst mode operation as shown in figures 34 and 35. The power dissipated in ROUT is 240 mW in this design, which can be reduced by increasing the resistor value athough this could cause the output to sightly exceed 60 V under an open load condition. This would not be an issue in designs with lower output voltages. Figure 35 shows that the burst duration at 230 VAC is much shorter than that at 120 VAC as shown in figure 34, which explains why the standby power is higher at low line. Application Note 42 Rev 1.1 2016-03-09 IRXLED04 55 W Flyback converter design using the IRS2982S controller Conclusion Under fault conditions as shown in section 10.12, the start-up cell continues to operate in support mode in the following cases: 1. 2. 3. The feedback loop is open because the IRS2982S never switches to support mode. In this case there is no output voltage regulation however the output voltage is limited by continuous operation of the over-voltage protection. The IRS2982S draws between 1 and 2 mA under this condition causing the case temperature to rise 50°C at maximum line input 265 VAC. The IC would therefore remain within its recommended operating range at an ambient temperature up to 75°C. VCC is not supplied through the auxiliary transformer winding but the feedback loop is still connected. In this case the HV start-up cell operating in support mode supplies all of the current to VCC. At maximum line input with 20% load, which is the worst case, the IRS2982S case temperature rises nearly 80°C. At a high ambient temperature there is a risk that the IC could exceed its maximum recommended operating temperature of 125°C. This situation should be avoided by ensuring that VCC receives current from the auxiliary winding during initial testing of the board. VCC is not sufficiently supplied through the auxiliary transformer winding so that the HV start-up cell continues to supply current in support mode. For this test the auxiliary VCC supply was adjusted to maintain VCC just above the under-voltage lock-out threshold where the HV start-up cell continues to supply a little over 1 mA during normal operation. In this case at maximum line input the IRS2982S case temperature rise measured was 40°C. Quasi-peak and average conducted emission sweeps fall within limits over the frequency spectrum from 150 kHz to 30 MHz. It should be noted that these measurements were not made by a certified test lab and are intended only as an indication of performance. In conclusion, the IRS2982S based Flyback converter design provides excellent performance and robustness with tight control and reliable protection. This design is well suited as a front end section in a two stage LED driver, where the back end section would typically be a constant current regulated Buck stage. Since there is no output over-load or short circuit protection the output current can reach several Amps, therefore the converter could become damaged under prolonged operation in these conditions. References [1] IRS2982SPBF SMPS control IC datasheet, Infineon Technologies. Revision History Major changes since the last revision Page or Reference -- Application Note Description of change First Release 43 Rev 1.1 2016-03-09 Trademarks of Infineon Technologies AG AURIX™, C166™, CanPAK™, CIPOS™, CoolGaN™, CoolMOS™, CoolSET™, CoolSiC™, CORECONTROL™, CROSSAVE™, DAVE™, DI-POL™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, Infineon™, ISOFACE™, IsoPACK™, i-Wafer™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OmniTune™, OPTIGA™, OptiMOS™, ORIGA™, POWERCODE™, PRIMARION™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, ReverSave™, SatRIC™, SIEGET™, SIPMOS™, SmartLEWIS™, SOLID FLASH™, SPOC™, TEMPFET™, thinQ!™, TRENCHSTOP™, TriCore™. Trademarks updated August 2015 Other Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2016-03-09 Published by Infineon Technologies AG 81726 Munich, Germany ifx1owners. © 2016 Infineon Technologies AG. All Rights Reserved. Do you have a question about this document? Email: [email protected] Document reference AppNote Number ANEVAL_2016_PL16_017 IMPORTANT NOTICE The information contained in this application note is given as a hint for the implementation of the product only and shall in no event be regarded as a description or warranty of a certain functionality, condition or quality of the product. Before implementation of the product, the recipient of this application note must verify any function and other technical information given herein in the real application. Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind (including without limitation warranties of non-infringement of intellectual property rights of any third party) with respect to any and all information given in this application note. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.