LANGUAGE
PRODUCT SPECIFICATION
JAPANESE
ENGLISH
SCOPE
9(&
2$
This specification covers the 0.5mm PITCH FPC CONNECTOR series.
PRODUCT NAME AND PART NUMBER
Material Number
Product Name
4X( X;O
Housing Assembly
(BOTTOM CONTACT TYPE)
$<
+ 9X
Embossed Tape Package For 52437-**26
LEAD FREE
LEAD FREE
Refer to the drawings.
RATINGS
Standard
Item
50 V
Rated Voltage (MAXIMUM)
[AC (
rms) /DC]
0.5 A
Rated Current (MAXIMUM)
-40
Ambient Temperature Range
+85
*1*2
1
2
Including terminal temperature rise.
FPC
FPC must be met temperature range specified in this standard.
A
B
SHEET
1-12
1-12
REVISE ON PC ONLY
REV.
TITLE:
0.5mm PITCH FFC / FPC CONNECTOR
REVISED
2005-1038
’04/10/06 E.SUZUKI
B
REV.
DESCRIPTION
DESIGN CONTROL
STATUS
J
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
WRITTEN
BY:
N.AIDA
CHECKED
BY:
K.TOJO
APPROVED
BY:
M.SASAO
DATE: YR/MO/DAY
2004/02/09
FILE NAME
SHEET
PS52437026.doc
1 OF 12
EN-37(019)
LANGUAGE
PRODUCT SPECIFICATION
JAPANESE
ENGLISH
PERFORMANCE
Electrical Performance
Item
Test Condition
FPC
10mA
(JIS C5402 5.4)
4-1-1
Contact
Resistance
20mV
20 milliohm MAXIMUM
Mate applicable FPC, measure by dry circuit, 20mV
MAXIMUM, 10mA MAXIMUM.
(JIS C5402 5.4)
FPC
DC 500V
(JIS C5402 5.2/MIL-STD-202
302)
$ D/P
D/P 4-1-2
Insulation
Resistance
Dielectric
Strength
$
50 Megohm MINIMUM
Mate applicable FPC and apply 500V DC between
adjacent terminal and ground.
(JIS C5402 5.2/MIL-STD-202 Method 302)
FPC
AC 250V
1
$ D/P
D/P 4-1-3
Requirement
(JIS C5402 5.1/MIL-STD-202
$
301)
No Breakdown
Mate applicable FPC, apply 250V AC (rms) for 1
minute between adjacent terminal or ground.
(JIS C5402 5.1/MIL-STD-202 Method 301)
REVISE ON PC ONLY
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
2 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
.
Mechanical Performance
Item
Test Condition
Actuator
Insertion/
Withdrawal Force
Mate applicable FPC and Insert and
withdraw actuator at the speed rate
of 25 3 mm per minute.
&J $
4-2-2
FPC
FPC Retention
Force
4-2-3
Terminal/Housing
Retention Force
4-2-4
Fitting nail
/Housing
Retention Force
&J $
FPC
25 3 mm
&J $
4-2-1
JAPANESE
ENGLISH
25 3 mm
Requirement
6
Refer to paragraph 6
FPC
Insert the actuator, pull the FPC at
the speed rate of 25 3 mm per
minute.
25 3mm
7
Refer to paragraph 7
Apply axial pull out force at the
speed rate of 25 3mm/minute on
the terminal assembled in the
housing.
25 3mm
3.0N {0.3kgf} MINIMUM
Apply axial pull out force at the
speed rate of 25 3mm/minute on
the fitting nail assembled in the
housing.
3.0N {0.3kgf} MINIMUM
REVISE ON PC ONLY
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
3 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
JAPANESE
ENGLISH
Environmental Performance and Others
Item
Test Condition
&J $
4-3-1
Repeated
Actuator
Insertion /
Withdrawal
1
Requirement
10
20
Insert and withdraw actuator up to 20 cycles at
the speed rate of less than 10 cycles per minute.
Contact
Resistance
40 milliohm
MAXIMUM
FPC
2$
(UL 498)
4-3-2
4-3-3
4-3-4
Temperature
Rise
Vibration
Shock
Mate applicable FPC, measure the temperature
rise of contact when the maximum AC rated
current is passed.
(UL 498)
DC 1mA
3
10 55 10Hz/
1.5mm
2
(MIL-STD-202
201)
Mate applicable FPC and subject to the following
vibration conditions, for a period of 2 hours in
each of 3 mutually perpendicular axes,
passing DC 1 mA during the test.
Amplitude : 1.5 mm P-P
Frequency : 10-55-10 Hz
Shall be traversed in 1 minute.
(MIL-STD-202, Method 201)
DC 1mA
6
490m/s2 {50G}
3
(JIS C0041 / MIL-STD-202
213)
Mate applicable FPC and subject to the following
shock conditions. 3 times of shocks shall be
applied for each 6 directions along 3 mutually
perpendicular axes, passing DC 1mA current
during the test.
(Total of 18 shocks)
2
Peak value : 490 m/s {50 G}
(JIS C0041/MIL-STD-202 Method 213)
REVISE ON PC ONLY
Temperature
Rise
Appearance
Contact
Resistance
Discontinuity
Appearance
Contact
Resistance
Discontinuity
30 °C
MAXIMUM
No Damage
40 milliohm
MAXIMUM
1.0
microsecond
MAXIMUM
No Damage
40 milliohm
MAXIMUM
1.0
microsecond
MAXIMUM
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
4 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
Item
4-3-5
Test Condition
FPC
85 2
1 2
( JIS C0021/MIL-STD-202
Heat
Resistance
4-3-6
Cold
Resistance
Requirement
96
108 )
Appearance
Mate applicable FPC and expose to 85 2 for
96 hours.
Upon completion of the exposure period, the test
specimens shall be conditioned at ambient room
conditions for 1 to 2 hours, after which the
specified measurements shall be performed.
(JIS C0021/MIL-STD-202 Method 108)
FPC
-40 2
96
1 2
(JIS C0020)
Mate applicable FPC and expose to –40 2
for 96 hours.
Upon completion of the exposure period, the test
specimens shall be conditioned at ambient room
conditions for 1 to 2 hours, after which the
specified measurements shall be performed.
(JIS C0020)
FPC
60 2
90
95%
96
1 2
(JIS C0022/MIL-STD-202
4-3-7
JAPANESE
ENGLISH
REVISE ON PC ONLY
Appearance
Contact
Resistance
Appearance
103)
Mate applicable FPC and expose to
60 2 ,relative humidity 90 to 95% for 96 hours.
Upon completion of the exposure period, the test
specimens shall be conditioned at ambient room
conditions for 1 to 2 hours, after which the
specified measurements shall be performed.
(JIS C0022/MIL-STD-202 Method 103)
Humidity
Contact
Resistance
Contact
Resistance
No Damage
40 milliohm
MAXIMUM
No Damage
40 milliohm
MAXIMUM
No Damage
40 milliohm
MAXIMUM
4-1-3
Must meet 4-1-3
Dielectric
Strength
Insulation
Resistance
20 Megohm
MINIMUM
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
5 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
Item
FPC
P
1
4-3-8
P
Temperature
Cycling
Test Condition
-55
30
5
3
JAPANESE
ENGLISH
Requirement
+85
P
30
1 2
(JIS C0025)
Mate applicable FPC and subject to the following
conditions for 5 cycles.
Upon completion of the exposure period, the test
specimens shall be conditioned at ambient room
conditions for 1 to 2 hours, after which the
specified measurements shall be performed.
1 cycle
30minutes
–55
+85
30minutes
(Transit time shall be with in 3 minutes)
(JIS C0025)
FPC
35 2
5 1%
48 4
(JIS C0023/MIL-STD-202
Appearance
Contact
Resistance
No Damage
40 milliohm
MAXIMUM
101)
Appearance
4-3-9
4-3-10
Salt Spray
SO2 Gas
Mate applicable FPC and expose to the following
salt mist condition.
Upon completion of the exposure period, salt
deposits shall be removed by a gentle wash or
dip in running water, after which the specified
measurements shall be performed.
NaCl solution
Concentration
: 5 1%
Spray time
: 48 4 hours
Ambient temperature : 35 2
(JIS C0023/MIL-STD-202 Method 101)
FPC
40 2
50 5ppm
24
No Damage
Contact
Resistance
40 milliohm
MAXIMUM
Mate applicable FPC and expose them to the
following SO2 gas atmosphere.
Temperature
40 2
Gas Density
50 5ppm
Duration
24 hours
REVISE ON PC ONLY
Contact
Resistance
40 milliohm
MAXIMUM
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
6 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
Item
FPC
4-3-11
XG0
NH3 Gas
1L
Test Condition
28%
40
25mL
Solder Ability
Requirement
XG0
Mate applicable FPC and 40 minutes exposure to
NH3 gas evaporating from 28% Ammonia
solution.
0.3mm
245 3
4-3-13
JAPANESE
ENGLISH
Contact
Resistance
0.3mm
3 0.5
Solder
Wetting
Tip of solder tails and fitting nails into the molten
solder (held at 245 3 ) up to 0.3mm from the
bottom of the housing for 3 0.5 seconds.
O:R
40 milliohm
MAXIMUM
75%
75% of
immersed
area must
show no
voids, pin
holes.
When reflowing
O:R
2
Refer to paragraph 8, two times.
4-3-14
Soldering iron method
0.3mm
370 400
Resistance to
Soldering Heat
+
$
0.3mm
5
Appearance
No Damage
0.3mm from terminal tip and fitting nail tip.
Soldering time : 5 seconds MAX.
Solder temperature : 370 400
(
)
{
}
Reference Standard
Reference Unit
PRODUCT SHAPE, DIMENSIONS AND MATERIALS
Refer to the drawing.
REVISE ON PC ONLY
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
7 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
[ 6.
&J $
JAPANESE
ENGLISH
ACTUATOR INSERTION/WITHDRAWAL FORCE ]
(
)
Insertion Force(MAX.)
No.of
CKT
UNIT
6
(
)
Withdrawal Force(MAX.)
1st
6th
20
20th
1st
6
6th
20
20th
6
N
{kgf}
30.3
{3.1}
28.4
{2.9}
28.4
{2.9}
39.2
{4.0}
35.2
{3.6}
35.2
{3.6}
7
N
{kgf}
31.3
{3.2}
29.4
{3.0}
29.4
{3.0}
40.1
{4.1}
36.2
{3.7}
36.2
{3.7}
8
N
{kgf}
32.3
{3.3}
30.3
{3.1}
30.3
{3.1}
41.1
{4.2}
37.2
{3.8}
37.2
{3.8}
9
N
{kgf}
33.3
{3.4}
31.3
{3.2}
31.3
{3.2}
42.2
{4.3}
38.3
{3.9}
38.3
{3.9}
10
N
{kgf}
34.3
{3.5}
32.3
{3.3}
32.3
{3.3}
43.1
{4.4}
39.2
{4.0}
39.2
{4.0}
11
N
{kgf}
35.2
{3.6}
33.3
{3.4}
33.3
{3.4}
44.1
{4.5}
40.2
{4.1}
40.2
{4.1}
12
N
{kgf}
36.2
{3.7}
34.3
{3.5}
34.3
{3.5}
45.0
{4.6}
41.1
{4.2}
41.1
{4.2}
13
N
{kgf}
37.2
{3.8}
35.2
{3.6}
35.2
{3.6}
46.1
{4.7}
42.2
{4.3}
42.2
{4.3}
14
N
{kgf}
38.2
{3.9}
36.2
{3.7}
36.2
{3.7}
47.0
{4.8}
43.1
{4.4}
43.1
{4.4}
15
N
{kgf}
39.2
{4.0}
37.2
{3.8}
37.2
{3.8}
48.1
{4.9}
44.1
{4.5}
44.1
{4.5}
16
N
{kgf}
40.1
{4.1}
38.2
{3.9}
38.2
{3.9}
49.0
{5.0}
45.0
{4.6}
45.0
{4.6}
17
N
{kgf}
41.1
{4.2}
39.2
{4.0}
39.2
{4.0}
49.9
{5.1}
46.0
{4.7}
46.0
{4.7}
REVISE ON PC ONLY
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
8 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
(
)
Insertion Force(MAX.)
No. of
CKT
UNIT
6
1st
6th
JAPANESE
ENGLISH
(
)
Withdrawal Force(MAX.)
20
20th
1st
6
6th
20
20th
18
N
{kgf}
42.1
{4.3}
40.1
{4.1}
40.1
{4.1}
50.9
{5.2}
47.0
{4.8}
47.0
{4.8}
19
N
{kgf}
43.1
{4.4}
41.1
{4.2}
41.1
{4.2}
51.9
{5.3}
48.0
{4.9}
48.0
{4.9}
20
N
{kgf}
44.1
{4.5}
42.1
{4.3}
42.1
{4.3}
52.9
{5.4}
49.0
{5.0}
49.0
{5.0}
21
N
{kgf}
45.0
{4.6}
43.1
{4.4}
43.1
{4.4}
53.9
{5.5}
50.0
{5.1}
50.0
{5.1}
22
N
{kgf}
46.0
{4.7}
44.1
{4.5}
44.1
{4.5}
54.8
{5.6}
50.9
{5.2}
50.9
{5.2}
23
N
{kgf}
47.0
{4.8}
45.0
{4.6}
45.0
{4.6}
55.8
{5.7}
51.9
{5.3}
51.9
{5.3}
24
N
{kgf}
48.0
{4.9}
46.0
{4.7}
46.0
{4.7}
56.8
{5.8}
52.9
{5.4}
52.9
{5.4}
25
N
{kgf}
49.0
{5.0}
47.0
{4.8}
47.0
{4.8}
57.8
{5.9}
53.9
{5.5}
53.9
{5.5}
26
N
{kgf}
49.9
{5.1}
48.0
{4.9}
48.0
{4.9}
58.8
{6.0}
54.8
{5.6}
54.8
{5.6}
27
N
{kgf}
50.9
{5.2}
49.0
{5.0}
49.0
{5.0}
59.7
{6.1}
55.8
{5.7}
55.8
{5.7}
28
N
{kgf}
51.9
{5.3}
49.9
{5.1}
49.9
{5.1}
60.7
{6.2}
56.8
{5.8}
56.8
{5.8}
29
N
{kgf}
52.9
{5.4}
50.9
{5.2}
50.9
{5.2}
61.7
{6.3}
57.8
{5.9}
57.8
{5.9}
30
N
{kgf}
53.9
{5.5}
51.9
{5.3}
51.9
{5.3}
62.7
{6.4}
58.8
{6.0}
58.8
{6.0}
REVISE ON PC ONLY
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
9 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
FPC
JAPANESE
ENGLISH
FPC RETENTION FORCE
(
No. of
CKT
UNIT
)
Retention Force
(MIN.)
1st
10
10th
(
No. of
CKT
UNIT
)
Retention Force
(MIN.)
1st
10
10th
6
N
{kgf}
2.5
{0.25}
2.0
{0.20}
19
N
{kgf}
8.9
{0.90}
5.8
{0.59}
7
N
{kgf}
3.0
{0.30}
2.3
{0.23}
20
N
{kgf}
9.4
{0.95}
6.1
{0.62}
8
N
{kgf}
3.5
{0.35}
2.6
{0.26}
21
N
{kgf}
9.8
{1.00}
6.4
{0.65}
9
N
{kgf}
4.0
{0.40}
2.9
{0.29}
22
N
{kgf}
10.3
{1.05}
6.7
{0.68}
10
N
{kgf}
4.5
{0.45}
3.2
{0.32}
23
N
{kgf}
10.8
{1.10}
7.0
{0.71}
11
N
{kgf}
4.9
{0.50}
3.5
{0.35}
24
N
{kgf}
11.3
{1.15}
7.3
{0.74}
12
N
{kgf}
5.4
{0.55}
3.8
{0.38}
25
N
{kgf}
11.8
{1.20}
7.6
{0.77}
13
N
{kgf}
5.9
{0.60}
4.1
{0.41}
26
N
{kgf}
12.3
{1.25}
7.9
{0.80}
14
N
{kgf}
6.4
{0.65}
4.4
{0.44}
27
N
{kgf}
12.8
{1.30}
8.2
{0.83}
15
N
{kgf}
6.9
{0.70}
4.7
{0.47}
28
N
{kgf}
13.3
{1.35}
8.5
{0.86}
16
N
{kgf}
7.4
{0.75}
4.9
{0.50}
29
N
{kgf}
13.8
{1.40}
8.8
{0.89}
17
N
{kgf}
7.9
{0.80}
5.2
{0.53}
30
N
{kgf}
14.3
{1.45}
9.1
{0.92}
18
N
{kgf}
8.4
{0.85}
5.5
{0.56}
REVISE ON PC ONLY
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
10 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
O:R
JAPANESE
ENGLISH
INFRARED REFLOW CONDITION
245 5 (
9 )
245 5 (PEAK TEMP.)
220
220 MINIMUM
40 60
40 60 seconds
90 120
90 120 seconds
(
150 180 )
(Pre-heat 150 180 )
N
:
6$ X
TEMPERATURE CONDITION GRAPH
(TEMPERATURE ON BOARD PATTERN SIDE)
O:R
O:R
O:R
NOTE; Please check the reflow soldering condition by your own devices beforehand.
Because the condition changes by the soldering devices,p.c.boards,and so on.
No moistuer treatment before reflow process.
REVISE ON PC ONLY
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
11 OF 12
EN-37-1(019)
LANGUAGE
PRODUCT SPECIFICATION
JAPANESE
ENGLISH
REV.
REV. RECORD
DATE
EC NO.
WRITTEN BY :
CHECKED BY :
A
RELEASED
‘04/02/09
J2003-2350
N.AIDA
K.TOJO
B
REVISED
‘04/10/06
J2005-1038
E.SUZUKI
K.TOJO
REVISE ON PC ONLY
TITLE:
0.5 mm PITCH FFC / FPC CONNECTOR
B
SEE SHEET 1 OF 12
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-52437-026
-LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FILE NAME
SHEET
PS52437026.doc
12 OF 12
EN-37-1(019)