AM80N03-06D Analog Power N-Channel 30-V (D-S) MOSFET PRODUCT SUMMARY VDS (V) rDS(on) m(Ω) 5.8 @ VGS = 10V 30 9 @ VGS = 4.5V These miniature surface mount MOSFETs utilize a high cell density trench process to provide low rDS(on) and to ensure minimal power loss and heat dissipation. Typical applications are DC-DC converters and power management in portable and battery-powered products such as computers, and printers. • • • • ID (A) 76 61 Low rDS(on) provides higher efficiency and extends battery life Low thermal impedance copper leadframe DPAK saves board space Fast switching speed High performance trench technology ABSOLUTE MAXIMUM RATINGS (TA = 25 oC UNLESS OTHERWISE NOTED) Parameter Symbol Limit Drain-Source Voltage 30 VDS Gate-Source Voltage VGS ±20 a Continuous Drain Current TC=25oC ID 77 Power Dissipationa TC=25oC PD Operating Junction and Storage Temperature Range THERMAL RESISTANCE RATINGS Parameter Symbol Maximum Junction-to-Ambient Maximum Junction-to-Case a RθJA RθJC -55 to 175 Maximum V A W 50 TJ, Tstg Units o Units 50 o 3.0 o C/W C/W Notes a. Surface Mounted on 1” x 1” FR4 Board. b. Pulse width limited by maximum junction temperature 1 PRELIMINARY Publication Order Number: DS-AM80N03-06D_A C AM80N03-06D Analog Power o SPECIFICATIONS (TA = 25 C UNLESS OTHERWISE NOTED) Parameter Symbol Test Conditions VGS(th) IGSS VDS = VGS, ID = 250 uA Limits Unit Min Typ Max Static Gate-Threshold Voltage Gate-Body Leakage Zero Gate Voltage Drain Current On-State Drain Current A ID(on) Drain-Source On-Resistance Forward Tranconductance Diode Forward Voltage Dynamic IDSS A A rDS(on) g fs VSD 1 VDS = 0 V, VGS = 20 V ±100 VDS = 20 V, VGS = 0 V 1 25 VDS = 20 V, VGS = 0 V, T J = 55oC VDS = 5 V, VGS = 10 V VGS = 10 V, ID = 1 A VGS = 4.5 V, ID = 1 A 34 uA A 5.8 9 VDS = 15 V, ID = 1 A IS = 1 A, VGS = 0 V V nA 22 1.1 mΩ S V b Total Gate Charge Gate-Source Charge Gate-Drain Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall-Time Qg Qgs Qgd t d(on) tr td(off) tf 20 VDS = 15 V, VGS = 4.5 V, ID = 1 A VDD = 25 V, RL = 25 Ω , ID = 1 A, VGEN = 10 V 4 9 6 7 70 30 Notes a. Pulse test: PW <= 300us duty cycle <= 2%. b. Guaranteed by design, not subject to production testing. Analog Power (APL) reserves the right to make changes without further notice to any products herein. APL makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does APL assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in APL data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. APL does not convey any license under its patent rights nor the rights of others. APL products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the APL product could create a situation where personal injury or death may occur. Should Buyer purchase or use APL products for any such unintended or unauthorized application, Buyer shall indemnify and hold APL and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that APL was negligent regarding the design or manufacture of the part. APL is an Equal Opportunity/Affirmative Action Employer. 2 PRELIMINARY Publication Order Number: DS-AM80N03-06D_A nC nS AM80N03-06D Analog Power Package Information Note: 1. All Dimension Are In mm. 2. Package Body Sizes Exclude Mold Flash, Protrusion Or Gate Burrs. Mold Flash, Protrusion Or Gate Burrs Shall Not Exceed 0.10 mm Per Side. 3. Package Body Sizes Determined At The Outermost Extremes Of The Plastic Body Exclusive Of Mold Flash, Gate Burrs And Interlead Flash, But Including Any Mismatch Between The Top And Bottom Of The Plastic Body. 3 PRELIMINARY Publication Order Number: DS-AM80N03-06D_A