eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 aFLAT-Series CRTtoLCD-51 Pro (21029E) CRTtoLCD-51 pro 16.10.2015 1 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 Technical Manual Table of Contents 1.0 General Information and Important Notes 1.1 Introduction 1.2 Technical Information Summary 1.3 Connectors 1.4 On Screen Display 1.5 Technical Specification 1.6 Supported Video Modes 1.7 Layout / Dimensions 1.8 Jumper overview 1.9 Serial OSD 2.0 Technical Support 2.1 Revision History CRTtoLCD-51 pro 16.10.2015 2 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.0 User Information Copyright 2015 by eCOUNT Technology GmbH. In this document eCOUNT Technology GmbH will also be referred to by the short form “eCOUNT Technology GmbH”. The information in this document has been carefully checked and is believed to be accurate and reliable. However, no responsibility is assumed for inaccuracies. Furthermore, eCOUNT Technology GmbH reserves the right to make changes to any portion of this manual to improve reliability, function or design. eCOUNT Technology GmbH does not assume any liability for any product or circuit described herein. 1.0 Trademarks AT and IBM are trademarks of International Business Machines. XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corporation. Microsoft is a registered trademark of Microsoft Corporation. Intel is a registered trademark of Intel Corporation. All other products and trademarks mentioned in this manual are trademarks of their respective owners. The reproduction, transmission or use of this document or its contents is not permitted without expressed written authority. Offenders will be liable for damages. All rights created by patent grant or registration of a utility model or design, are reserved. 1.0 General For the circuits, descriptions and tables indicated no responsibility is assumed as far as patents or other rights of third parties are concerned. The information in the Technical Descriptions describes the type of the boards and shall not be considered as assured characteristics. The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. CRTtoLCD-51 pro 16.10.2015 3 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.0 Warranty Each board is carefully and thoroughly tested before being shipped. If, however, problems should occur during the operation, please check your user specific settings of all boards included in your system. This is often the source of the fault. If a board is defective, it can be sent to your supplier for repair. Please take care of the following steps: - The board returned should correspond to the factory default settings since a test is only possible under these settings. In order to repair your board as fast as possible , we require some additional information from you. Please fill out the attached Repair Form and include it with the defective board. If possible, the board will be upgraded to the latest version without additional cost. Upon receipt of the board, please be aware that your user specific settings were changes during the test. Within the guarantee, the repair is free as long as the guarantee conditions were kept. If no fault has been found, you will be charged with the test cost due to the high test expenditure. Repairs outside of the guarantee will be charged. This eCOUNT Technology GmbH product is warranted against defects in material and workmanship for our guaranteed warranty period from the date of shipment. During the warranty period, eCOUNT Technology GmbH will, at its option, either repair or replace products which prove to be defective. For warranty service or repair, the product must be returned to a service facility designated by eCOUNT Technology GmbH. The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance or handling by buyer, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper installation or maintenance. eCOUNT Technology GmbH will not be responsible for any defects or damages due to a faulty eCOUNT Technology GmbH product other than the products supplied by eCOUNT Technology GmbH. CRTtoLCD-51 pro 16.10.2015 4 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.1 Introduction The CRTtoLCD-51 pro is a highly integrated TFT panel interface controller, which allows an easy adaptation of standard video input sources like analog RGB via DVI-I & DisplayPort to a digital TFT panel. The CRTtoLCD-51 pro need only one single 12V DC power supply and incorporates all needed functionality to build up a full featured TFT monitor. The card generates the necessary power sequencing for the flat screen. The highly flexible architecture of the CRTtoLCD-5 pro panel interface allows adapting nearly any available TFT panel. Therefore a variety of panel adapters and programming are available on request. CRTtoLCD-51 pro 16.10.2015 5 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.2 Technical Information Summary Features - analog RGB-Interface via DVI-I up to 1920x1200(WUXGA)@60Hz - highest quality via DVI-D up to 1920x1200(WUXGA)@60Hz (with full Zoom & Shrink capabilities) - standard DVI-I connector - all color depths up to 24 Pixel - Integrated DisplayPort 1.1 compliant receiver up to UXGA - horizontal & vertical Zoom - 2 separate onboard power supplies for flat panel (up to 3A & controller) High power connector for BL (up to 3.5A) - embedded Microcontroller with serial ROM Interface - Capability of connecting light sensor to control backlight brightness (optional) - On Screen Display control for all features - On-chip versatile OSD engine - All system clocks synthesized from a single external crystal - Programmable gamma correction (CLUT) - RealColor control provide sRGB compliance - backlight dimming support, - JILI30 (up to 2x24 bit dual channel LVDS) JILI40 optional Output up to 1920x1200(WUXGA)@60Hz - USB configuration port (optional) - Analog Light Sensor(ALS) input - IR receiver for standard remote control - Independent Panel Power supply - Low EMI and power saving features High-Quality Advanced Scaling - Fully programmable zoom ratios - High quality shrink capability from UXGA resolution - RealRecovery function provides full color recovery image for refresh rates higher than those supported by the LCD panel - Moiré cancellation Analog RGB Input Port - Supports up to 1920x1200(WUXGA)@60Hz Auto-Configuration / Auto-Detection - Phase and image positioning - Input format detection - Compatibility with all graphic cards and standard VESA modes Ultra-Reliable DVI Compliant Input Port - Operating up to 225 MHz 1920x1200(WUXGA)@60Hz - Direct connect to all DVI compliant digital transmitters CRTtoLCD-51 pro 16.10.2015 6 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.2 Technical Information Summary RealColor Technology - Digital brightness and contrast controls - TV color controls including hue and saturation control - Flesh tone adjustment - Full color matrix allows end users to experience the same color as viewed on CRTs and other displays ( e.g. sRGB compliance ) LVDS Output Format - Single / double channel up to 1920x1200(WUXGA)@60Hz - Support for 8 or 6-bit panels (with high quality dithering) - One or two pixel output format On-chip OSD Controller - On-chip RAM for downloadable menus - 1,2 and 4-Bit per pixel character cells - Horizontal and vertical stretch of OSD menus - Blinking, transparency and blending - Proportional fonts Display Interface Features : - Control signal generation for backlight inverter and LED driver - backlight dimming support - voltage generation and power sequence control for panel - Flat screens can be used with either 3.3V, 5V or 12V. - Digital RGB panel 18-Bit interface (optional with separate adapter) - LVDS panel interface ( one and double port up to 24 Bit ) Operating Features : - 5 or 6 (optional) button user interface - On Screen Display ( OSD ) control for full features - Full multi sync capable - VESA DPMS and DDC2B support - Single voltage supply ( +12V DC ) - No software drivers needed! CRTtoLCD-51 pro 16.10.2015 7 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.3 Connectors 1.3.1 Display Port input CN3 1.3.2 OSD key pad connector CN501 1.3.3 Backlight connector CN101 1.3.4 Serial Port connector CN200 1.3.5 KAB-JILI30-Interface / JILI40(Optional) CN100/CN800 1.3.6 DC Power Supply CN300, CN301 1.3.7 Flatpanel Power Supply Configuration JP102 1.3.8 Backlight Control Configuration JP100, JP101 1.3.9 ADC Input Connector CN7 1.3.10 DVI-I Input Conn. (incl. RGB Analog Input) CN1 CRTtoLCD-51 pro 16.10.2015 8 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.3.1 Displayport Input CN3 Connector MOLEX 47272-001 Name ML_Lane 0 (p) GND ML_Lane 0 (n) ML_Lane 1 (p) GND ML_Lane 1 (n) ML_Lane 2 (p) GND ML_Lane 2 (n) ML_Lane 3 (p) GND ML_Lane 3 (n) GND GND AUX CH (p) GND AUX CH (n) Hot Plug RETURN DP_PWR Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Description O O O O O O O O O O O O O O O O O O O O Lane 0 (positive) Ground Lane 0 (negative) Lane 1 (positive) Ground Lane 1 (negative) Lane 2 (positive) Ground Lane 2 (negative) Lane 3 (positive) Ground Lane 3 (negative) Pulled to Ground Pulled to Ground Auxiliary Channel (positive) Ground Auxiliary Channel (negative) Hot Plug Detect Return for Power Power for connector (3.3 V 500 mA) CRTtoLCD-51 pro 16.10.2015 9 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.3.2 OSD Keypad Connector CN501 Description 14 Contacts IDC Connector, Gold plated, double row, vertical mount, through hole Name Pin Pin Name +5V Keypad Power out Keypad Button (Exit) Keypad Button (Right) Transmit Data (TTL) LED Green *Note1 Not connected Power Ground VCC KEY KEY TXD LED 1 NC GND 1 3 5 7 9 11 13 O O O O O O O O O O O O O O 2 4 6 8 10 12 14 LED_ENA KEY KEY RXD KEY Vcc12 GND Description LED_ENA *Note2 Keypad Button (Menu) Keypad Button (Left) Receive Data (TTL) Keypad Button(Power) +12V Power out Power Ground *Note1 Max. 4,5 mA output current *Note2 Open Collector(OC) or VCC12 (+12V DC-IN) 1.3.3 Backlight Connector CN101 Connector: Molex 53261-1071 Matching Connector: Molex 51021-1000 Connector Single Row, 10 Contacts, Case/Size : Right Angle, 1,25mm Pitch Pin Name Description O O O O O O O O O O 1 2 3 4 5 6 7 8 9 10 BLON GND GND Backlight Backlight Backlight Backlight GND GND BKLTADJ Backlight control signal (TTL, refer to JP100) Power Ground Power Ground power power power power supply supply supply supply Typical. +12V (Note same as DC Input Voltage , 1 Ampere per contact allowed) Power Ground Power Ground analog 0V to +5V / 0V to +12V (refer to JP101) PWM / Analog dimming (refer to JP1) CRTtoLCD-51 pro 16.10.2015 10 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.3.4 Serial Port connector CN200 The OSD ( On Screen Display ) can be controlled either trough the keypad or the serial connector CN500/501 for configuration purposes or mass production. See also chapter 1.8 for detailed description. Caution ! The transmit and receive signals have TTL level! Connector: Molex 53261-0471 Matching Connector: Molex 51021-0400 Pin Name Description O O O O 1 2 3 4 VCC RXD TXD GND +5V DC Power (output) Receive Data Signal Transmit Data Signal Power Ground CRTtoLCD-51 pro 16.10.2015 11 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.3.5 KAB-JILI30-Interface CN100 Connector: JAE FI-X30S-HF Matching Connector: JAE FI-X30H Name FTX0FTX0+ FTX1FTX1+ FTX2FTX2+ GND FTXCFTXC+ FTX3FTX3+ STX0STX0+ GND STX1STX1+ GND STX2STX2+ STXCSTXC+ STX3STX3+ GND NC PPWR NC PANEL_VCC PANEL_VCC PANEL_VCC Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Description O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O Odd Receiver Signal Odd Receiver Signal Odd Receiver Signal Odd Receiver Signal Odd Receiver Signal Odd Receiver Signal Power Ground Odd Clock Signal Odd Clock Signal Odd Receiver Signal Odd Receiver Signal Even Receiver Signal Even Receiver Signal Power Ground Even Receiver Signal Even Receiver Signal Power Ground Even Receiver Signal Even Receiver Signal Even Clock Signal Even Clock Signal Even Receiver Signal Even Receiver Signal Power Ground Not Connected Controls Panel Digital Power Not Connected Panel Power (refer to JP102) Panel Power (refer to JP102) Panel Power (refer to JP102) CRTtoLCD-51 pro 16.10.2015 12 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 JILI40-Interface CN800 (optional) All flat screen signals are LVDS compatible Connector Double Row 2mm, 40 Contacts, Gold plated Case/Size : Straight, Through Hole Description Name Pin Enables Backlight Backlight Adjust Even Receiver Signal Even Clock Signal +12V Even Receiver Signal Even Receiver Signal +12V Even Receiver Signal Odd Receiver Signal Power Ground 2 I C clock (Master) Power Ground Odd Clock Signal Odd Receiver Signal Power Ground Odd Receiver Signal Odd Receiver Signal Power Ground Panel VCC ( switched ) BLON# BLADJ STX3STXC+ +12V STX2STX1+ +12V STX0FTX3+ GND SCL GND FTXCFTX2+ GND FTX1FTX0+ GND Vcc_P 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 1.3.6 O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O Pin Name Description 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 BLON# STX3+ +12V STXCSTX2+ +12V STX1STX0+ +12V FTX3GND SDA FTXC+ GND FTX2FTX1+ GND FTX0GND Vcc_P Enables Backlight Even Receiver Signal +12V Even Clock Signal Even Receiver Signal +12V Even Receiver Signal Even Receiver Signal +12V Odd Receiver Signal Power Ground 2 I C Data (Master) Odd Clock Signal Power Ground Odd Receiver Signal Odd Receiver Signal Power Ground Odd Receiver Signal Power Ground Panel VCC ( switched ) DC Power Supply CN300 Apply operating voltage using connector CN300 or CN301. 4 Contact Connector, Single Row, Right Angle, Polarization, through hole Pin O O O O 1 2 3 4 Name NC GND GND +12V Description Not connected Power Ground Power Ground +12 V DC Power Input CRTtoLCD-51 pro 16.10.2015 13 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.3.7 DC Power Supply CN301 Apply operating voltage using connector CN300 or CN301. DC POWER JACK, Case/Size : PCB-Mount 2mm Pin Diameter Pin O O 1.3.7 1 2 Name +12V GND Description +12 V DC Power Input Power Ground Flatpanel Power Supply Configuration JP102 Short pins 1-2 or 2-3 or leave open to choose required voltage supply. Caution ! Only one configuration for flatpanel is allowed, otherwise the board is permanently damaged. Connector Single Row 2,54 mm, 3 Contacts, Gold plated Case/Size : Vertical, Through Hole 1 2 3 Pin 2-3 1-2 open O O O 1.3.8 Delivery Default 1-2 closed +12V +5V +3.3V Never unplug/replug while in use! Backlight Control Configuration JP100 Use JP100 to control polarity of backlight control signal Connector Single Row 2,54 mm, 3 Contacts, Gold plated Case/Size : Vertical, Through Hole 1 2 3 Pin 2-3 1-2 Delivery Default 1-2 closed O O O /BLON BLON Never unplug/replug while in use! 1.3.8 Backlight Control Configuration JP1 Use JP1 to configure PWM or analog backlight control Connector Single Row 2,54 mm, 3 Contacts, Gold plated Case/Size : Vertical, Through Hole 1 2 3 Pin 2-3 1-2 Delivery Default 1-2 closed O O O analog PWM Never unplug/replug while in use! CRTtoLCD-51 pro 16.10.2015 14 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.3.8 Backlight Output Adjust Configuration JP101 Use JP101 to set correct backlight adjust range I-out 20mA max. Connector Single Row 2,54 mm, 3 Contacts, Gold plated Case/Size : Vertical, Through Hole 1 2 3 Pin 2-3 1-2 Delivery Default 1-2 closed O O O Typ. 0-12V Typ. 0-5V Never unplug/replug while in use! 1.3.9 ADC / IR Input Connector CN7 (Light Sensor Input / IR diode input) Connector: Molex 53261-0571 Matching Connector: Molex 51021-0500 Pin Name O O O O O 1 2 3 4 5 DVDD5 ADC1 / IR M_I2C_SDA M_I2C_SCL GND Description 5V output source (max.50mA) ADC1 / IR Input *Note1 Master I2C Bus Master I2C Bus Power Ground *Note1 ADC1 input range is 0 – 3.3V Digital IR input for IR-Diode (0 / 3.3V) CRTtoLCD-51 pro 16.10.2015 15 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.3.10 DVI-I Input Connector CN1 This input supports the connection of DVI capable video cards including RGB Analog Input supports resolutions from 640x480 up to 1920x1200. Description Connector 29 Contacts, Gold plated Case/Size : Vertical, Through Hole Name Pin Pin Name Receiver Signal(-) ( RX2- ) RX2Power Ground GND Not connected NC 2 I C Data SDA Receiver Signal(-) ( RX1- ) RX1Power Ground GND Not connected NC Power Ground GND Receiver Signal(-) ( RX0- ) RX0Power Ground GND Not connected NC Clock Signal(+) (RXC+) RXC+ Analog red RED Analog blue BLUE Analog GND GND 1 3 5 7 9 11 13 15 17 19 21 23 C1 C3 C5 O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 2 4 6 8 10 12 14 16 18 20 22 24 C2 C4 C51 RX2+ NC SCL NC RX1+ NC +5V HP RX0+ NC GND RXCGREEN HSYNC GND Description ReceiverSignal(+)(RX2+) Not connected I2C clock Not connected Receiver Signal(+)(RX1+) Not connected +5V from DVI video card Hot Plug Receiver Signal(+)(RX0+) Not connected Power Ground Clock Signal(-) (RXC-) Analog green Horizontal sync Analog GND CRTtoLCD-51 pro 16.10.2015 16 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.4 On Screen Display With the self explaining OSD ( On Screen Display ) you can modify the settings and control the special features of the CRTtoLCD-51pro. The OSD uses a number of menus and submenus for making changes and turning the special features on or off. The configuration can be done via the OSDkeypad (OSD-Panel-Kit). To start the OSD press the “OSD” button on the keypad, after switching the power supply on. If a valid flat panel configuration is installed, the OSD Main Menu will be displayed. To select an tab, simply use the button “UP” or ”DOWN” to move cursor to the tab you want and press button “OSD”. When you use the “Exit” and press the “CONFIRM”-button, the OSD will be closed. To use a tab menu, simply use “OSD”-button to select the field. Use “UP” or “DOWN” to select a value for that field. The “Exit”-field on bottom-side on the tab will go up to the tab-selection. Simply press “OSD”-button. the tab the the Note: All changed values will only be saved by selecting “Exit” from the OSD. If not, the adjusted values will be lost after loss of power. CRTtoLCD-51 pro 16.10.2015 17 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.5 Technical Specification These values were measured with OSD-Panel attached and without flatpanel and backlight inverter. - Supply voltage at 25˚C without load: Minimum supply voltage : Typical supply voltage : +11,4 V DC +12,0 V DC Absolute Maximum supply voltage : +12,6 V DC - Typical Input current at 25˚C without load: CRTtoLCD-51pro with input signal (WUXGA), Panelfile (WUXGA) : 212 mA CRTtoLCD-51pro with power down typical : 65 mA - Input Supply voltage ripple : typical 100 mV peak to peak 0 – 20 MHz - Current Rating of Flatpanel Power supply: PANEL VCC Steady State 3V / 5V and 12V @ +-5% : 3A PANEL VCC 5sec. -5% 3V3 @4,33A PANEL VCC 5sec. -5% 5V @ 4,15A PANEL VCC 5sec. -2% 12V @ 4A Note: Output power without any switch or short circuit breaker - Slewrate of Flatpanel Power supply with 3A load PANEL VCC 3V3 302us PANEL VCC 5V 408us PANEL VCC 12V 1.7ms - Voltage and Current Rating of Backlight Power supply: Direct +12V Output voltage without any switch or short circuit breaker CN101: Maximum output current 4A CN100: Maximum output current 3A VGA connector signals : Sync input voltage low : 0.8 V Sync input voltage high : 2.4 V RGB input voltage RGB input current : 0 – 0.7 V with 75 Ohm external termination : 0 – 5 mA - Temperature : ambient : 0˚ C – 60˚ C (*1) Non operating : - 10˚ C – 85˚ C (*1) The maximum temperature on the module surface can exceed above mentioned ambient temperature. It is the user responsibility to keep this temperature within the above specification. - Thermal gradient : operating : 25˚ C per hour non-operating : 40˚ C per hour - Relative Humidity : operating : 10% - 90 % RH non-condensing non operating : 5% - 95% RH non-condensing CRTtoLCD-51 pro 16.10.2015 18 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.5 Technical Specification - Mechanical : Shock : 50G/20ms square wave maximum Vibration : 1G/0-600Hz, dwell not to exceed - Altitude : operating : 0 – 3000 m non-operating : 0 – 5000 m - Dimensions of the printed circuit board : Width: 114.28 mm Length: 179.07 mm Thickness: 1.50 mm - Dimensions of the module : Width: 119.50 mm Length: 179.07 mm Height: 16.50 mm +2mm (*) Note : The dimension of the module can change if cable, Adapter or Keypad plugged in! CRTtoLCD-51 pro 16.10.2015 19 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.6 Supported Video Modes (Analog Input) Generally all VESA compatible video modes are supported. If modes are not supported the controller displays “Invalid Mode” on the flat panel. In this case use the Flat Panel Editor, available on request, to add this special mode to the supported mode table. Video Mode Input 720 x 400 640 x 350 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1680 x 1050 1600 x 1200 1920 x 1080 1920 x 1200 Following modes are tested Vertical refresh rate 70 Hz 70 Hz 70 Hz 59,9 Hz 60 Hz 72 Hz 72,8 Hz 75 Hz 56,25 Hz 60 Hz 70 Hz 72 Hz 75 Hz 60 Hz 70 Hz 72 Hz 75 Hz 60 Hz 70 Hz 75 Hz 60 Hz 70 Hz 75 Hz 60 Hz 60 Hz 60 Hz 60 Hz Mode standard DOS DOS DOS VGA VGA VGA VGA VGA SVGA SVGA SVGA SVGA SVGA XGA XGA XGA XGA XGA+ XGA+ XGA+ SXGA SXGA SXGA WSXGA+ UXGA FHD WUXGA CRTtoLCD-51 pro 16.10.2015 20 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 Supported Video Modes (DVI Input) 1.6 Generally all VESA compatible video modes are supported. If modes are not supported the controller displays “Invalid Mode” on the flat panel. In this case use the Flat Panel Editor, available on request, to add this special mode to the supported mode table. Following modes are tested Video Mode Input 640 x 480 800 x 600 1024 x 768 1280 x 1024 1680 x 1050 1200 x 1600 1920 x 1080 1920 x 1200 Vertical refresh rate 60 60 60 60 60 60 60 60 Hz Hz Hz Hz Hz Hz Hz Hz Mode standard VGA SVGA XGA SXGA WSXGA+ UXGA FHD WUXGA CRTtoLCD-51 pro 16.10.2015 21 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.7 Layout/Schematics CRTtoLCD-51 pro CRTtoLCD-51 pro 16.10.2015 22 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.8 Jumper Overview CRTtoLCD-51 pro 16.10.2015 23 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 1.9 OSD Keypad OSD-Keypad “OSD-Panel“ Power ON/OFF LED 25 mm 120mm Keypad JP1 connected to CN501 of CRTtoLCD-51 pro CRTtoLCD-51 pro 16.10.2015 24 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 2.0 Technical Support Please report any errors or problems to this email address: [email protected]. Normally, there is no telephone support. In your email message, please include the following information : Company Name Your Name Address Email Telephone/Fax Exact description of the hardware, etc. Exact description of the software used (for example: Win XP with driver XYZ ) Exact description of the error. CRTtoLCD-51 pro 16.10.2015 25 eCOUNT Technology GmbH Schatzbogen 60/62 D - 81829 München Tel.: 0049 (0) 89 454571 - 0 Fax.: 0049 (0) 89 454571 - 11 2.1 Date 16.10.2015 Revision History Author V. Irion Version 1.0 Description Initial release CRTtoLCD-51 pro 16.10.2015 26