eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 aFLAT-series Flat Panel Controller CRTtoLCD-71 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 Contents GENERAL INFORMATION AND IMPORTANT NOTES ............................ 2 1.1 1.2 1.3 1.4 2. User Information ......................................... Trademarks ............................................. General................................................ Warranty ............................................... 2 2 2 2 INTRODUCTION .................................................... 3 TECHNICAL INFORMATION SUMMARY ...................................... 3 3. CONFIGURATION ................................................... 5 3.1 3.2 3.3 3.4 3.5 3.6 3.7 4. Backlight adjust configuration JP600 ........................... Backlight ON configuration JP601............................. Backlight adjust level configuration JP602 ....................... Backlight voltage configuration JP602 .......................... Panel voltage configuration JP602 ............................ Display port power configuration JP500 ........................ Serial port configuration JP1300 ............................. 5 5 6 6 6 6 7 CONNECTORS ..................................................... 8 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 4.18 Contents SVHS Video Input CN300 .................................. 8 Composite video input CN301 ............................... 8 YUV analog input CN302 (optional) ........................... 8 VGA/RGB analog Input CN303 (optional) ....................... 8 DVI-I input connector CN400 ................................ 9 Display Port connector CN500 ............................... 9 JILI40-Interface CN601 ................................... 10 JILI30-Interface CN603 ................................... 11 Backlight Connector CN7001 ............................... 12 Audio input/output CN700 (optional) .......................... 12 IR input CN800 ......................................... 12 OSD keypad connector CN801 .............................. 12 ADC Input Connector CN900 (Light Sensor Input) ................ 13 GPIO Connector CN 801 .................................. 13 RS232 Serial OSD connector CN1300 ........................ 13 USB Serial OSD connector (optional) ......................... 13 DC Power Supply 4-Pol. CN1500 ............................ 14 DC Power Supply DC-Jack CN1501 .......................... 14 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 5. ON SCREEN DISPLAY ............................................... 15 6. TECHNICAL SPECIFICATIONS ........................................ 16 7. SUPPORTED VIDEO MODES .......................................... 18 8. LAYOUT / SCHEMATICS ............................................. 19 TECHNICAL SUPPORT ................................................. 21 9. REVISION HISTORY ................................................ 21 Contents eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 General information and important notes 1.1 User Information Copyright 2014 by ECOUNT Technology GmbH. In this document ECOUNT Technology GmbH will also be referred to by the short form “eCOUNT”. The information in this document has been carefully checked and is believed to be accurate and reliable. However, no responsibility is assumed for inaccuracies. Furthermore, ECOUNT Technology GmbH reserves the right to make changes to any portion of this manual to improve reliability, function or design. ECOUNT Technology GmbH does not assume any liability for any product or circuit described herein. 1.2 Trademarks AT and IBM are trademarks of International Business Machines. XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corporation. Microsoft is a registered trademark of Microsoft Corporation. Intel is a registered trademark of Intel Corporation. All other products and trademarks mentioned in this manual are trademarks of their respective owners. The reproduction, transmission or use of this document or its contents is not permitted without expressed written authority. Offenders will be liable for damages. All rights created by patent grant or registration of a utility model or design, are reserved. 1.3 General For the circuits, descriptions and tables indicated no responsibility is assumed as far as patents or other rights of third parties are concerned. The information in the Technical Descriptions describes the type of the boards and shall not be considered as assured characteristics. The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. General information and important notes 2 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 1.4 Warranty Each board is carefully and thoroughly tested before being shipped. If, however, problems should occur during the operation, please check your user specific settings of all boards included in your system. This is often the source of the fault. If a board is defective, it can be sent to your supplier for repair. Please take care of the following steps: - The board returned should correspond to the factory default settings since a test is only possible under these settings. In order to repair your board as fast as possible, we require some additional information from you. Please fill out the attached Repair Form and include it with the defective board. If possible, the board will be upgraded to the latest version without additional cost. Upon receipt of the board, please be aware that your user specific settings are changed during the test. Within the guarantee, the repair is free as long as the guarantee conditions were kept. If no fault has been found, you will be charged with the test cost due to the high test expenditure. Repairs outside of the guarantee will be charged. This ECOUNT Technology GmbH product is warranted against defects in material and workmanship for our guaranteed warranty period from the date of shipment. During the warranty period, ECOUNT Technology GmbH will, at its option, either repair or replace products which prove to be defective. For warranty service or repair, the product must be returned to a service facility designated by ECOUNT Technology GmbH. The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance or handling by buyer, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper installation or maintenance. ECOUNT Technology GmbH will not be responsible for any defects or damages due to a faulty ECOUNT Technology GmbH product other than the products supplied by ECOUNT Technology GmbH. General information and important notes 2 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 2. Introduction The CRTtoLCD-71 is a highly integrated TFT panel interface controller, which allows an easy adaptation of standard video input sources like S-video, composite video, DVI or analog RGB to a digital TFT panel. The CRTtoLCD-71 only needs one single 12V power supply and incorporates all needed functionality to build up a full featured TFT monitor. The card generates the necessary power sequencing for the flat screen. The highly flexible architecture of the CRTtoLCD-71 panel interface allows adapting nearly any available TFT panel. Therefore a variety of panel adapters and programming are available on request. Technical Information Summary FLEXIBLE DIGITAL AND ANALOG CAPTURE • Integrated dual 10-bit triple ADCs with capture up to 205 MHz • Input resolution support up to UXGA@75 Hz/WUXGA@60 Hz • Composite-Sync and Sync-on-Green (SOG) support • Instant Auto™ for automatic phase and clock adjustment • 4:4:4/4:2:2/CCIR656/601 30/24/16/8-bit digital input port INTEGRATED HDMI 1.3 RECEIVER • Integrated multi-mode HDMI 1.3 • Front-end multiplexer supports two physical input ports • 1080p HDMI capture support • HDCP 1.2a content protection with integrated key storage • xvYCC support based on IEC61966-2-4 color standard • Deep Color and Wide Gamut support: 12-bit HDMI input at YCC 4:4:4 INTEGRATED 3D VIDEO DECODER • Single 3D Adaptive Comb Filter for Luma–Chroma separation • Supports Composite, S-Video, and Component SD and HD video input signals • Macrovision®b and VCR trick mode support INTEGRATED DISPLAYPORT 1.1 RECEIVER • DisplayPort interconnectivity provides very high bandwidth compared to conventional digital interfaces • DisplayPort link comprising of 4 main lines and 1 auxiliary channel • WUXGA capture support INTEGRATED AUDIO PROCESSING • 2 Stereo (L/R) analog inputs • Additional and separate audio inputs for HDMI SPDIF • Outputs include 2 analog DACs and SPDIF • Worldwide multi-standards audio support • Integrated I2S Audio Delay to exact audio and video synchronization • Supports 5.1 analog/digital output stream (Left, Center, Right, LS, RS + LFE) FAROUDJA REALCOLOR® • Faroudja RealColor® provides true 10-bit color processing • Active color management with overlapping regions • Adaptive Contrast Control • Integrated noise filter to eliminate contrast noise Introduction 3 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 FAROUDJA DCDI CINEMA® FORMAT CONVERSION • Low Angle De-interlacing processing • Per Pixel Motion Adaptive De-interlacing (MADi) up to 1080i format • Format conversion up to 1080p resolutions • Adaptive 3D/TNR Noise Reduction PICTURE-IN-PICTURE (PIP) • Programmable PIP channel horizontal and vertical filter coefficients • Flexible PIP, PBP, and POP support capability (Video, Graphics) • DCDi Edge® processing for second channel window FAROUDJA® TRUELIFE™ VIDEO ENHANCER • High performance programmable sharpening filters with Noise Coring • Programmable Main channel horizontal and vertical filter coefficients • Non-linear Chroma and Luma enhancement DDR2 MEMORY CONTROLLER • 32-bitDDR2 memory I/F support ON-CHIP MICROPROCESSOR AND OSD CONTROLLER • Integrated x186-based microprocessor • General Purpose Inputs/Outputs (GPIOs) • 2-wire serial master bus interface for external device control • Integrated I/R decoder and low bandwidth ADC • Advanced bit-mapped OSD controller OUTPUT FORMATS • Dual-channel/single-channel 18/24/30-bit LVDS transmitters • Single-channel 24/30-bit TTL output • Adaptive Contrast Ratio (ACR) control for automatic, intelligent backlight adjustments Display Interface Features : • Control signal generation for backlight inverter • backlight dimming support (PWM and voltage controlled ) • Voltage generation and power sequence control for panel • Flat screens can be used with either 3.3V, 5V or 12V. • JILI30/40/50 (LVDS) panel interface (one and double port up to 30 Bit) Operating Features: - 5 button user interface (OSD Keypad) - On Screen Display (OSD) control for all features - Full multi sync capable - VESA DPMS and DDC2B support - Single voltage supply (+12V/24V DC ) - Dynamic Power Management for minimal power consumption via DPMS - No software drivers needed! Technical Information Summary 4 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 3. Configuration 3.1 Backlight adjust configuration JP600 O O O Pin Description 1-2 2-3 PWM Adjust Linear Adjust Never unplug/replug this while in use 3.2 Backlight ON configuration JP601 O O O Pin Description 1-2 2-3 Active high BLON Active low BLON Never unplug/replug this while in use Configuration 5 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 3.3 Backlight adjust level configuration JP602 O O O Pin Description 1-2 2-3 Open 5V Adjust 12V Adjust 3.3V Adjust Never unplug/replug this while in use 3.4 Backlight voltage configuration JP1500 OO OO OO Pin Description Open 1-2 3-4 3.3V 5V 12V Never unplug/replug this while in use 3.5 Panel voltage configuration JP1501 OO OO OO Pin Description Open 1-2 3-4 3.3V 5V 12V Never unplug/replug this while in use 3.6 Display port power configuration JP500 O O Pin Description 1-2 Open Board provides power to pin 20 of DP connector Pin 20 DP connector open Never unplug/replug this while in use Configuration 6 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 3.7 Serial port configuration JP1300 O O O Pin Description 1-2 2-3 Uart0 is TTL/USB, Uart1 RS232 Uart0 and Uart1 are RS232 Never unplug/replug this while in use Configuration 7 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 4. Connectors 4.1 SVHS Video Input CN300 O O O O Pin Name Description 1 2 3 4 GND GND Y C Power Ground Power Ground Y component of video signal C component of video signal 4.2 Composite video input CN301 O O Pin Name Description 1 2 GND CVBS Power Ground CVBS video signal 4.3 YUV analog input CN302 (optional) Description Name Red/Y in Green/U in Blue/V Audio Left 1 in Audio Right 1 in RED GREEN BLUE AIL1 AIR1 Pin 1 3 5 7 9 Pin O O O O O O O O O O 2 4 6 8 10 Name GND GND GND GND GND Description Ground Ground Ground Ground Ground 4.4 VGA/RGB analog Input CN303 (optional) O O O O O O O O O O O O Connectors Pin Name Description 1 2 3 4 5 6 7 8 9 10 11 12 RED GND GREEN GND BLUE GND DDC_SDA HSYNC VSYNC DDC_SCL GND +5V in Analog input red Ground Analog input green Ground Analog input blue Ground DDC Serial Data Horizontal Sync input Vertical Sync input DDC Serial Clock Ground +5V Power Supply from Video Card 8 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 4.5 DVI-I input connector CN400 Description Name Pin Receiver Signal(-) ( RX2- ) Power Ground Not connected 2 I C Data Receiver Signal(-) ( RX1- ) Power Ground Not connected Power Ground Receiver Signal(-) ( RX0- ) Power Ground Not connected Clock Signal(+) (RXC+) Analog red Analog blue Analog GND RX2GND NC SDA RX1GND NC GND RX0GND NC RXC+ RED BLUE GND 1 3 5 7 9 11 13 15 17 19 21 23 C1 C3 C5 O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O Pin Name Description 2 4 6 8 10 12 14 16 18 20 22 24 C2 C4 C5-1 RX2+ NC SCL NC RX1+ NC +5V HP RX0+ NC GND RXCGREEN HSYNC GND Receiver Signal(+) ( RX2+ ) Not connected 2 I C clock Not connected Receiver Signal(+) ( RX1+ ) Not connected +5V from DVI video card Hot Plug Receiver Signal(+) ( RX0+ ) Not connected Power Ground Clock Signal(-) (RXC-) Analog green Horizontal sync Analog GND 4.6 Display Port connector CN500 Pin O O O O O O O O O O O O O O O O O O O O Connectors 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Name Description ML_Lane 0 (p) GND ML_Lane 0 (n) ML_Lane 1 (p) GND ML_Lane 1 (n) ML_Lane 2 (p) GND ML_LANE 2 (N) ML_Lane 3 (p) GND ML_Lane 3 (n) GND GND AUX CH (p) GND AUX CH (n) Hot Plug RETURN DP_PWR Lane 0 (positive) Ground Lane 0 (negative) LANE 1 (POSITIVE) Ground Lane 1 (negative) Lane 2 (positive) Ground LANE 2 (NEGATIVE) Lane 3 (positive) GROUND LANE 3 (NEGATIVE) Pulled to Ground Pulled to Ground Auxiliary Channel (positive) Ground Auxiliary Channel (negative) Hot Plug Detect Return for Power POWER FOR CONNECTOR (3.3 V 500 MA) 9 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 4.7 JILI44-Interface CN600 Description Name Enables Backlight BLON# Even Rx Signal(-) (R2IN 4+) STX4+ Power Ground GND Even Rx Signal(-) (R2IN 3-) STX3Even Clock Signal(+) (CK2IN +) STXC+ Power Ground GND Even Rx Signal(+) (R2IN 2+) STX2+ Even Rx Signal(-) (R2IN 1-) STX1Power Ground GND Even Rx Signal(-) (R2IN 0-) STX0Odd Rx Signal(+)(R1IN 4+) FTX4+ Power Ground GND Odd Rx Signal(-) (R1IN 3-) FTX3Odd Clock Signal(+) (CK1IN +) FTXC+ Power Ground GND Odd Rx Signal(+)(R1IN 2+) FTX2Odd Rx Signal(+) (R1IN 1+) FTX1+ Power Ground GND Odd Rx Signal(-) (R1IN 0-) FTX02 I C clock SCL Panel VCC ( switched ) Vcc_P Panel VCC ( switched ) Vcc_P Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O Pin Name Description 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 BLADJ STX4STX3+ GND STXCSTX2GND STX1+ STX0+ GND FTX4FTX3+ GND FTXCFTX2+ GND FTX1FTX0+ GND SDA Vcc_P Vcc_P Backlight Adjust Even Rx Signal(-) (R2IN 4-) Even Rx Signal(-) (R2IN 3+) Power Ground Even Clock Signal(-) (CK2IN -) Even Rx Signal(-) (R2IN 2-) Power Ground Even Rx Signal(+)(R2IN1+) Even Rx Signal(+) (R2IN 0+) Power Ground Odd Rx Signal(+)(R1IN 4-) Odd Rx Signal(+)(R1IN 3+) Power Ground Odd Clock Signal(-) (CK1IN -) Odd Rx Signal(-) (R1IN 2+) Power Ground Odd Rx Signal(-) (R1IN 1-) Odd Rx Signal(+)(R1IN 0+) Power Ground 2 I C Data Panel VCC ( switched ) Panel VCC ( switched ) Pin Name Description 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 BLON# STX3+ +12V STXCSTX2+ +12V STX1STX0+ +12V FTX3GND SDA FTXC+ GND FTX2FTX1+ GND FTX0GND Vcc_P Enables Backlight Even Rx Signal(+) (R2IN 3+) +12V Even Clock Signal(-) (CK2IN -) Even Rx Signal(+) (R2IN 2+) +12V Even Rx Signal(-) (R2IN 1-) Even Rx Signal(+) (R2IN 0+) +12V Odd Rx Signal(-) (R1IN 3-) Power Ground 2 I C Data Odd Clock Signal(+) (CK1IN +) Power Ground Odd Rx Signal(-) (R1IN 2-) Odd Rx Signal(+) (R1IN 1+) Power Ground Odd Rx Signal(-) (R1IN 0-) Power Ground Panel VCC ( switched ) 4.8 JILI40-Interface CN601 Description Name Enables Backlight BLON# Backlight Adjust BLADJ Even Rx Signal(-) (R2IN 3-) STX3Even Clock Signal(+) (CK2IN +) STXC+ +12V +12V Even Rx Signal(-) (R2IN 2-) STX2Even Rx Signal(+)(R2IN1+) STX1+ +12V +12V Even Rx Signal(-) (R2IN 0-) STX0Odd Rx Signal(+)(R1IN 3+) FTX3+ Power Ground GND 2 I C clock SCL Power Ground GND Odd Clock Signal(-) (CK1IN -) FTXCOdd Rx Signal(+)(R1IN 2+) FTX2+ Power Ground GND Odd Rx Signal(-) (R1IN 1-) FTX1Odd Rx Signal(+)(R1IN 0+) FTX0+ Power Ground GND Panel VCC ( switched ) Vcc_P Connectors Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 10 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 4.9 JILI30-Interface CN603 Description Name Pin Odd Rx Signal- (R1IN 0-) Odd Rx Signal- (R1IN 1-) Odd Rx Signal- (R1IN 2-) Power Ground Odd Clock Signal+ (CK1IN +) Odd Rx Signal+ (R1IN 3+) Even Rx Signal+ (R2IN 0+) Even Rx Signal- (R2IN 1-) Power Ground Even Rx Signal+ (R2IN 2+) Even Clock Signal+ (CK2IN +) Even Rx Signal+ (R2IN 3+) I²C Data I²C Clock Panel VCC ( switched ) FTX0FTX1FTX2GND FTXC+ FTX3+ STX0+ STX1GND STX2+ STXC+ STX3+ SDA SCL Vcc_P 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Connectors O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 11 Pin Name Description 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 FTX0+ FTX1+ FTX2+ FTXCFTX3STX0GND STX1+ STX2STXCSTX3GND DEN Vcc_P Vcc_P Odd Rx Signal+ (R1IN 0+) Odd Rx Signal+ (R1IN 1+) Odd Rx Signal+ (R1IN 2+) Odd Clock Signal- (CK1IN -) Odd Rx Signal- (R1IN 3-) Even Rx Signal- (R2IN 0-) Power Ground Even Rx Signal+ (R2IN 1+) Even Rx Signal- (R2IN 2-) Even Clock Signal- (CK2IN -) Even Rx Signal- (R2IN 3-) Power Ground Display Enable Panel VCC ( switched ) Panel VCC ( switched ) eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 4.10 Backlight Connector CN7001 Pin O O O O O O O O O O 1 2 3 4 5 6 7 8 9 10 Name Description BLON GND GND Backlight power supply Backlight power supply Backlight power supply Backlight power supply GND GND BKLTADJ BACKLIGHT CONTROL SIGNAL Power Ground Power Ground TYPICAL. +12V (NOTE SAME AS DC INPUT VOLTAGE , 1 AMPERE PER CONTACT ALLOWED) Power Ground Power Ground analog 0V to +5V or 0V to +12V 4.11 Audio input/output CN700 (optional) Description Name Line out left Line out right Line in left 2 Line in right 2 SPDIF in SPDIF out AOL AOR AIL2 AIR2 SPDIFI SPDIFO Pin 1 3 5 7 9 11 Pin O O O O O O O O O O O O 2 4 6 8 10 12 Name GND GND GND GND GND +3.3V Description Ground Ground Ground Ground Ground +3.3V power supply 4.12 IR input CN800 CN1001 O O O Pin Name Description 1 2 2 VCC GND Out 5 Volts output Power Ground Output from the IR receiver 4.13 OSD keypad connector CN801 Description +5V DC Power Confirm Key (TTL) Down Key (TTL) ADC Input *Note1 Switch LED (TTL) Low active Reset (TTL) Power Ground Name VCC KEY KEY ADC1 KEY /Reset GND Pin 1 3 5 7 9 11 13 Pin O O O O O O O O O O O O O O *Note1: Input range is 0 - 3V. Shared with CN900 Connectors 12 2 4 6 8 10 12 14 Name LED KEY KEY IR KEY +12V GND Description LED Enable (Operating) OSD Menu key (TTL) Up Key (TTL) Output of IR receiver ON/OFF Key (TTL) +12V DC Power +5V DC from DVI video card eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 4.14 ADC Input Connector CN900 (Light Sensor Input) Connector: Molex 53261-0590 Matching Connector: Molex 51021-0500 Pin Name O O O O O 1 2 3 4 5 GND ADC1 DVDD3.3 ADC2 GND Description Power Ground ADC1 Input *Note1 3.3 VOLT OUTPUT SOURCE (MAX.50MA) ADC2 Input *Note1 Power Ground *Note1: Input range is 0 - 3V. Onboard pulled up to DVDD3.3 through 4, 7 KΩ resistor. 4.15 GPIO Connector CN 801 Connector: Molex 53261-0590 Matching Connector: Molex 51021-0500 Pin Name O O O O O 1 2 3 4 5 DVD3.3 GND GPIO0 GPIO1 GPIO2 Description 3.3 Volt output source (max.50mA) Ground General Purpose I/O / PWM0 General Purpose I/O / PWM1 General Purpose I/O / PWM2 4.16 RS232 Serial OSD connector CN1300 Description Not Connected Transmit Signal 1 Receive Signal 1 Not Connected Power Ground Name Pin 1 3 5 7 9 NC TXD1 RXD1 NC GND Pin O O O O O O O O O O 2 4 6 8 10 Name NC RXD2 TXD2 NC +5V Description Not Connected Receive Signal 2 Transmit Signal 2 Not Connected +5V DC Power 4.17 USB Serial OSD connector (optional) Connector: Molex 53261-0590 Matching Connector: Molex 51021-0500 Pin Name O O O O Connectors 1 2 3 4 +5V GND GPIO0 GPIO2 USB 5V input USB+ USBGND 13 Description eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 4.18 DC Power Supply 4-Pol. CN1500 O O O O Pin Name Description 1 2 3 4 NC GND GND +12V Not connected Power Groundl Power Ground 12V DC Power 4.19 DC Power Supply DC-Jack CN1501 O O Connectors Pin Name Description 1 2 +12V GND +12 V DC Power Ground 14 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 5. On Screen Display With the OSD ( On Screen Display ) you can modify the settings and control the special features of the CRTtoLCD-71. The OSD uses a number of menus for making changes and turning the special features on or off. The configuration can be done via the OSD-keypad (OSD-Panel-Kit). To start the OSD press the “OSD” button on the keypad, after switching the power supply on. If a valid flat panel configuration is installed, the OSD Main Menu will be displayed. To select an menu point, simply use the button “UP” or ”DOWN” to move the cursor to the menu point you want and press the button “OSD”. To get back to the previous menu point press the “CONFIRM” button. To select a function, simply use “OSD”-button to select the field. Use “UP” or “DOWN” to select a value for that field. With the “CONFIRM” button you can exit the current function. On Screen Display 15 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 6. Technical Specifications These values were measured with OSD-Panel attached and without flatpanel and backlight inverter. - Supply voltage at 25˚C : Minimum supply voltage Typical supply voltage Absolute Maximum supply voltage - + 11,4 V DC / 22,8 V DC + 12,0 V DC / 24V DC + 12.6 V DC / 25.2 V DC Typical Input current at 25˚C: CRTtoLCD-71- OSD-keypad, input signal SXGA: CRTtoLCD-71- OSD-keypad, power down: TBD mA TBD mA - 100 mV peak to peak 0 – 20 MHz Supply voltage ripple: VGA connector signals : Sync input voltage low : Sync input voltage high: RGB input voltage: termination RGB input current: 0.8 V 2.4 V 0 – 0.7 V with 75 Ohm external 0 – 5 mA - Current Rating of Flatpanel Power supply (preliminary): PANEL VCC Steady State 3V / 5V and 12V @ +-5% : 3A PANEL VCC 5sec. -5% 3V3 @5,6A PANEL VCC 5sec. -5% 5V @ 5,15A PANEL VCC 5sec. -2% 12V @ 4A Note: Output power without any switch or short circuit breaker - Temperature: ambient: 0˚C – 60˚C (*1) non operating: -10˚C – 85˚C (*1) The maximum operating temperature is the maximum measurable temperature on any spot on the module surface. It is the user responsibility to keep this temperature within the above specification. - - - Temperature gradient: operating: non operating: 25˚C per hour 40˚C per hour Relative Humidity: operating: non operating: 10% - 90% RH non-condensing 5% - 95% RH non-condensing Mechanical: Shock: Vibration: Technical Specifications 5G/20ms square wave maximum 1G/0-600Hz, dwell not to exceed 16 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 - - Dimensions of the printed circuit board: Width: Length: Thickness: 114.29 mm 179.07 mm 1.50 mm Dimensions of the module: Width: Length: Height: 119.50 mm 179.07 mm 16.50 mm max. 35mm Note : The dimension of the module may vary depending on P/N or change if cable, Adapter or Keypad plugged in! Technical Specifications 17 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 7. Supported Video Modes Generally all VESA compatible video modes are supported. If modes are not supported the controller displays “Invalid Mode” on the flat panel. In this case use the Configuration Workbench (KCWB), available on request, to add this special mode to the supported mode table. Following modes are tested: Video Mode Input 720 x 400 640 x 350 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1600 x 1200 1920 x 1200 Supported Video Modes Vertical refresh rate 70 Hz 70 Hz 70 Hz 59,9 Hz 60 Hz 72 Hz 72,8 Hz 75 Hz 85 Hz 56,25 Hz 60 Hz 70 Hz 72 Hz 75 Hz 85 Hz 60 Hz 70 Hz 72 Hz 75 Hz 85 Hz 75 Hz 60 Hz 70 Hz 75 Hz 85 Hz 60 Hz 60 Hz 18 Mode standard DOS DOS DOS VGA VGA VGA VGA VGA VGA SVGA SVGA SVGA SVGA SVGA SVGA XGA XGA XGA XGA XGA SXGA SXGA SXGA SXGA UXGA WUXGA eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 8. Layout / Schematics Layout / Schematics 19 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 OSD-KEYPAD “OSD-PANEL“ Power ON/OFF LED 25 mm 120 MM Keypad JP1 connected to CN2 of CRTtoLCD-7! Layout / Schematics 20 eCOUNT Technology GmbH Schatzbogen 60 D-81829 München Tel.: 0049 (0)89 454571-0 Fax.: 0049 (0)89 454571-11 Technical Support Please report any errors or problems to this email address: [email protected]. Normally, there is no telephone support. In your email message, please include the following information: - 9. Company Name Your Name Address Email Telephone/Fax Exact description of the hardware, etc. Exact description of the software in use (for example: WinXP with driver XYZ ) Exact description of the error. Revision History Date 01.07.2014 Author A.Stauffenberg Technical Support Version Description 1.0 Initial Release 21