Download

eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
aFLAT-Series
CRTtoLCD 51
(21031E)
CRTtoLCD-51
01.02.2014
1
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
CRTtoLCD-51
(21031E)
Technical Manual
Table of Contents
1.0
General Information and Important Notes
1.1
Introduction
1.2
Technical Information Summary
1.3
Connectors
1.4
On Screen Display
1.5
Technical Specification
1.6
Supported Video Modes
1.7
Layout / Dimensions
1.8
Serial OSD
1.9
Technical Support
2.0
Revision History
CRTtoLCD-51
01.02.2014
2
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.0
User Information
Copyright 2010 by eCOUNT Technology GmbH.
In this document eCOUNT Technology GmbH will also be referred to by the
short form “eCOUNT Technology GmbH”.
The information in this document has been carefully checked and is
believed to be accurate and reliable. However, no responsibility is assumed
for inaccuracies. Furthermore, eCOUNT Technology GmbH reserves the
right to make changes to any portion of this manual to improve reliability,
function or design. eCOUNT Technology GmbH does not assume any
liability for any product or circuit described herein.
1.0
Trademarks
AT and IBM are trademarks of International Business Machines.
XT, AT, PS/2 and Personal System/2 are trademarks of International
Business Machines Corporation.
Microsoft is a registered trademark of Microsoft Corporation.
Intel is a registered trademark of Intel Corporation.
All other products and trademarks mentioned in this manual are
trademarks of their respective owners.
The reproduction, transmission or use of this document or its contents is
not permitted without expressed written authority.
Offenders will be liable for damages. All rights created by patent grant or
registration of a utility model or design, are reserved.
1.0
General
For the circuits, descriptions and tables indicated no responsibility is
assumed as far as patents or other rights of third parties are concerned.
The information in the Technical Descriptions describes the type of the
boards and shall not be considered as assured characteristics.
The reproduction, transmission or use of this document or its contents is
not permitted without express written authority. Offenders will be liable for
damages. All rights, including rights created by patent grant or registration
of a utility model or design, are reserved.
CRTtoLCD-51
01.02.2014
3
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.0
Warranty
Each board is carefully and thoroughly tested before
being shipped. If, however, problems should occur
during the operation, please check your user specific
settings of all boards included in your system. This is
often the source of the fault. If a board is defective, it
can be sent to your supplier for repair. Please take care
of the following steps:
-
-
The board returned should correspond to the
factory default settings since a test is only
possible under these settings.
In order to repair your board as fast as possible
, we require some additional information from
you. Please fill out the attached Repair Form
and include it with the defective board.
If possible, the board will be upgraded to the
latest version without additional cost.
Upon receipt of the board, please be aware
that your user specific settings were changes
during the test.
Within the guarantee, the repair is free as long as the
guarantee conditions were kept. If no fault has been
found, you will be charged with the test cost due to the
high test expenditure. Repairs outside of the guarantee
will be charged.
This eCOUNT Technology GmbH product is warranted
against defects in material and workmanship for our
guaranteed warranty period from the date of shipment.
During the warranty period, eCOUNT Technology GmbH
will, at its option, either repair or replace products
which prove to be defective.
For warranty service or repair, the product must be
returned to a service facility designated by eCOUNT
Technology GmbH.
The foregoing warranty shall not apply to defects
resulting from improper or inadequate maintenance or
handling by buyer, unauthorized modification or
misuse, operation outside of the environmental
specifications for the product, or improper installation
or maintenance.
eCOUNT Technology GmbH will not be responsible for
any defects or damages due to a faulty eCOUNT
Technology GmbH product other than the products
supplied by eCOUNT Technology GmbH.
CRTtoLCD-51
01.02.2014
4
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.1
Introduction
The CRTtoLCD-51 is a highly integrated TFT panel interface controller,
which allows an easy adaptation of standard video input sources like
analog RGB via DVI-I & DisplayPort to a digital TFT panel.
The CRTtoLCD-51 need only one single 12V DC power supply and
incorporates all needed functionality to build up a full featured TFT
monitor. The card generates the necessary power sequencing for the flat
screen. The highly flexible architecture of the CRTtoLCD-51 panel interface
allows adapting nearly any available TFT panel. Therefore a variety of
panel adapters and programming are available on request.
CRTtoLCD-51
01.02.2014
5
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.2
Technical Information Summary
Features
- analog RGB-Interface via DVI-I up to UXGA@75Hz
- highest quality via DVI-D up to UXGA@60Hz.
(with full Zoom & Shrink capabilities)
- standard DVI-I connector
- all color depths up to 24 Pixel
- Integrated DisplayPort 1.1 compliant receiver up to UXGA
- horizontal & vertical Zoom
- 2 separate onboard power supplies for flat panel (up to 3A & controller)
High power connector for BL (up to 4A) for LVDS version
- embedded Microcontroller with serial ROM Interface
- Capability of connecting light sensor to control backlight brightness
(optional)
- On Screen Display control for all features
- On-chip versatile OSD engine
- All system clocks synthesized from a single external crystal
- Programmable gamma correction (CLUT)
- RealColor control provide sRGB compliance
- backlight dimming support,
- JILI30 (up to 2x24 bit dual channel LVDS) JILI40 optional
Output up to UXGA@60Hz
- USB configuration port (optional)
- IR receiver for standard remote control (optional)
- Light sensor input
- Independent Panel Power supply
- Low EMI and power saving features
High-Quality Advanced Scaling
- Fully programmable zoom ratios
- High quality shrink capability from UXGA resolution
- RealRecovery function provides full color recovery image for refresh rates
higher than those supported by the LCD panel
- Moiré cancellation
Analog RGB Input Port
Auto-Configuration / Auto-Detection
modes
Ultra-Reliable DVI Compliant Input Port
p to 165 MHz (up to UXGA 60 Hz)
CRTtoLCD-51
01.02.2014
6
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.2
Technical Information Summary
RealColor Technology
- TV color controls including hue and saturation control
- Flesh tone adjustment
- Full color matrix allows end users to experience the same color as viewed
on CRTs and other displays ( e.g. sRGB compliance )
LVDS Output Format
- Single / double channel up to SXGA 75 Hz output
- Support for 8 or 6-bit panels (with high quality dithering)
- One or two pixel output format
On-chip OSD Controller
- On-chip RAM for downloadable menus
- 1,2 and 4-Bit per pixel character cells
- Horizontal and vertical stretch of OSD menus
- Blinking, transparency and blending
- Proportional fonts
Display Interface Features :
- Control signal generation for backlight inverter
- backlight dimming support
- voltage generation and power sequence control for panel
- Flat screens can be used with either 3.3V, 5V or 12V.
- Digital RGB panel 18-Bit interface (optional with separate adapter)
- LVDS panel interface ( one and double port up to 24 Bit )
Operating Features :
- 5 or 6 (optional) button user interface
- On Screen Display ( OSD ) control for full features
- Full multi sync capable
- VESA DPMS and DDC2B support
- Single voltage supply ( +12V DC )
- No software drivers needed!
CRTtoLCD-51
01.02.2014
7
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
Connectors
1.3
1.3.1
Display Port input
CN3
1.3.2
OSD key pad connector
CN501
1.3.3
Backlight connector
CN101
1.3.4
Serial Port connector
CN200
1.3.5
KAB-JILI30-Interf./JILI40(opt.) CN100/CN800 Note1
1.3.6
DC Power Supply
CN300, CN301
1.3.7
Flatpanel Power Supply conf.
JP102
1.3.8
Backlight Control Configuration
JP100, JP101
1.3.9
ADC Input Connector
CN7
1.3.10 DVI-I Input Conn. (incl. RGB Analog Input) CN1
*Note1 can vary. Depends on version of CRTtoLCD-51
CRTtoLCD-51
01.02.2014
8
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.3.1
Displayport Input CN3
Connector MOLEX 47272-001
Name
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ML_Lane 0 (p)
GND
ML_Lane 0 (n)
ML_Lane 1 (p)
GND
ML_Lane 1 (n)
ML_Lane 2 (p)
GND
ML_Lane 2 (n)
ML_Lane 3 (p)
GND
ML_Lane 3 (n)
GND
GND
AUX CH (p)
GND
AUX CH (n)
Hot Plug
RETURN
DP_PWR
1.3.2
Description
Description
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Lane 0 (positive)
Ground
Lane 0 (negative)
Lane 1 (positive)
Ground
Lane 1 (negative)
Lane 2 (positive)
Ground
Lane 2 (negative)
Lane 3 (positive)
Ground
Lane 3 (negative)
Pulled to Ground
Pulled to Ground
Auxiliary Channel (positive)
Ground
Auxiliary Channel (negative)
Hot Plug Detect
Return for Power
Power for connector (3.3 V
500 mA)
OSD Keypad Connector CN501
14 Contacts IDC Connector, Gold plated, double row,
vertical mount, through hole
Name
Pin
Pin
Name
Description
+5V Keypad Power out
Keypad Button (Exit)
Keypad Button (Right)
Transmit Data (TTL)
LED Green *Note1
Not connected
Power Ground
VCC
KEY
KEY
TXD
LED 1
NC
GND
1
3
5
7
9
11
13
O
O
O
O
O
O
O
O
O
O
O
O
O
O
2
4
6
8
10
12
14
LED 2
KEY
KEY
RXD
KEY
Vcc12
GND
LED Red *Note1
Keypad Button (Menu)
Keypad Button (Left)
Receive Data (TTL)
Keypad Button (Power)
+12V Power Keypad out
Power Ground
*Note1 Max. 4,5 mA output current
CRTtoLCD-51
01.02.2014
9
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.3.3
Backlight Connector CN101
Connector: Molex 53261-1071
Matching Connector: Molex 51021-1000
Connector Single Row, 10 Contacts, Case/Size : Right Angle, 1,25mm Pitch
Pin
Name
Description
O
O
O
O
O
O
O
O
O
O
1.3.4
1
2
3
4
5
6
7
8
9
10
BLON
GND
GND
Backlight
Backlight
Backlight
Backlight
GND
GND
BKLTADJ
Backlight control signal (TTL, refer to JP100)
Power Ground
Power Ground
power
power
power
power
supply
supply
supply
supply
Typical. +12V (Note same as DC Input Voltage ,
1 Ampere per contact allowed)
Power Ground
Power Ground
analog 0V to +5V or 0V to +12V (refer to
JP101)
Serial Port connector CN200
The OSD ( On Screen Display ) can be controlled either trough
the keypad or the serial connector CN500/501 for configuration
purposes or mass production. See also chapter 1.8 for detailed
description.
Caution ! The transmit and receive signals have TTL level!
Connector: Molex 53261-0471
Matching Connector: Molex 51021-0400
Pin
Name
Description
O
O
O
O
1
2
3
4
VCC
RXD
TXD
GND
+5V DC Power (output)
Receive Data Signal
Transmit Data Signal
Power Ground
CRTtoLCD-51
01.02.2014
10
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.3.5
KAB-JILI30-Interface CN100
Connector: JAE FI-X30S-HF
Matching Connector: JAE FI-X30H
Name
FTX0FTX0+
FTX1FTX1+
FTX2FTX2+
GND
FTXCFTXC+
FTX3FTX3+
STX0STX0+
GND
STX1STX1+
GND
STX2STX2+
STXCSTXC+
STX3STX3+
GND
NC
PPWR
NC
PANEL_VCC
PANEL_VCC
PANEL_VCC
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Description
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Even Receiver Signal
Even Receiver Signal
Even Receiver Signal
Even Receiver Signal
Even Receiver Signal
Even Receiver Signal
Power Ground
Even Clock Signal
Even Clock Signal
Even Receiver Signal
Even Receiver Signal
Odd Receiver Signal
Odd Receiver Signal
Power Ground
Odd Receiver Signal
Odd Receiver Signal
Power Ground
Odd Receiver Signal
Odd Receiver Signal
Odd Clock Signal
Odd Clock Signal
Odd Receiver Signal
Odd Receiver Signal
Power Ground
Not Connected
Controls Panel Digital
Not Connected
Panel Power (refer to
Panel Power (refer to
Panel Power (refer to
Power
JP102)
JP102)
JP102)
CRTtoLCD-51
01.02.2014
11
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
JILI40-Interface CN800 (optional)
All flat screen signals are LVDS compatible
Connector Double Row 2mm, 40 Contacts, Gold plated
Case/Size : Straight, Through Hole
Description
Name
BLON#
BLADJ
Pin
Pin
1
3
O O
O O
2
4
STX3- 5
Even Receiver Signal(-) (R2IN 3-)
STXC+ 7
Even Clock Signal(+) (CK2IN +)
+12V 9
+12V
O O
O O
O O
6
8
10
Enables Backlight
Backlight Adjust
Even Receiver Signal(-) (R2IN 2-)
Even Receiver Signal(+)(R2IN1+)
+12V
STX2- 11
STX1+ 13
+12V 15
O O
O O
O O
12
14
16
Even Receiver Signal(-) (R2IN 0-)
Odd Receiver Signal(+)(R1IN 3+)
Power Ground
2
I C clock
STX0FTX3+
GND
DDCS
CL
GND
FTXCFTX2+
GND
FTX1FTX0+
GND
Vcc_P
17
19
21
23
O
O
O
O
O
O
O
O
18
20
22
24
25
27
29
31
33
35
37
39
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
26
28
30
32
34
36
38
40
Power Ground
Odd Clock Signal(-) (CK1IN -)
Odd Receiver Signal(+)(R1IN 2+)
Power Ground
Odd Receiver Signal(-) (R1IN 1-)
Odd Receiver Signal(+)(R1IN 0+)
Power Ground
Panel VCC ( switched )
1.3.6
Name
Description
BLON#
STX3+
Enables Backlight
Even Receiver Signal(+) (R2IN
3+)
+12V
+12V
STXCEven Clock Signal(-) (CK2IN -)
STX2+
Even Receiver Signal(+) (R2IN
2+)
+12V
+12V
STX1Even Receiver Signal(-) (R2IN 1-)
STX0+
Even Receiver Signal(+) (R2IN
0+)
+12V
+12V
FTX3Odd Receiver Signal(-) (R1IN 3-)
GND
Power Ground
2
DDCSDA
I C Data
FTXC+
GND
FTX2FTX1+
GND
FTX0GND
Vcc_P
Odd Clock Signal(+) (CK1IN +)
Power Ground
Odd Receiver Signal(-) (R1IN 2-)
Odd Receiver Signal(+) (R1IN 1+)
Power Ground
Odd Receiver Signal(-) (R1IN 0-)
Power Ground
Panel VCC ( switched )
DC Power Supply CN300
Apply operating voltage using connector CN300 or CN301.
4 Contact Connector, Single Row, Right Angle, Polarization, through hole
Pin
O
O
O
O
1
2
3
4
Name
NC
GND
GND
+12V
Description
Not connected
Power Ground
Power Ground
+12 V DC Power Input
CRTtoLCD-51
01.02.2014
12
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.3.7
DC Power Supply CN301
Apply operating voltage using connector CN300 or CN301.
DC POWER JACK, Case/Size : PCB-Mount 2mm Pin Diameter
Pin
O
O
1.3.7
1
2
Name
+12V
GND
Description
+12 V DC Power Input
Power Ground
Flatpanel Power Supply Configuration JP102
Short pins 1-2 or 2-3 or leave open to choose required voltage
supply.
Caution ! Only one configuration for flatpanel is allowed,
otherwise the board is permanently damaged.
Connector Single Row 2,54 mm, 3 Contacts, Gold plated
Case/Size : Vertical, Through Hole
1 2 3
Pin
2-3
1-2
open
O O O
1.3.8
Delivery Default
1-2 closed
+12V
+5V
+3.3V
Never unplug/replug while in use!
Backlight Control Configuration JP100
Use JP100 to control polarity of backlight control signal.
Connector Single Row 2,54 mm, 3 Contacts, Gold plated
Case/Size : Vertical, Through Hole
1 2 3
Pin
2-3
1-2
Delivery Default
1-2 closed
O O O
/BLON
BLON
Never unplug/replug while in use!
1.3.8
Backlight Control Configuration JP1
Use JP100 to control polarity of backlight control signal.
Connector Single Row 2,54 mm, 3 Contacts, Gold plated
Case/Size : Vertical, Through Hole
1 2 3
Pin
2-3
1-2
Delivery Default
1-2 closed
O O O
analog
PWM
Never unplug/replug while in use!
CRTtoLCD-51
01.02.2014
13
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.3.8
Backlight Output Adjust Configuration JP101
Use JP101 to set correct backlight adjust range I-out 20mA max.
Connector Single Row 2,54 mm, 3 Contacts, Gold plated
Case/Size : Vertical, Through Hole
1 2 3
Pin
2-3
1-2
Delivery Default
1-2 closed
O O O
Typ. 0-12V
Typ. 0-5V
Never unplug/replug while in use!
1.3.9
ADC Input Connector CN7
(Light Sensor Input)
Connector: Molex 53261-0571
Matching Connector: Molex 51021-0500
Pin
Name
Description
O
O
1
2
DVDD5
ADC1
5V output source (max.50mA)
ADC1 Input *Note1
O
O
O
3
4
5
M_I2C_SDA
M_I2C_SCL
GND
Master I2C Bus
Master I2C Bus
Power Ground
*Note1 Input range is 0 - 3V. Onboard pulled up to DVDD3.3 through 4, 7 KΩ resistor.
CRTtoLCD-51
01.02.2014
14
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.3.10
DVI-I Input Connector CN1
This input supports the connection of DVI
capable video cards
including RGB Analog Input
supports resolutions from 640x480 up to
1600x1200.
Description
Connector 29 Contacts, Gold plated
Case/Size : Vertical, Through Hole
Name Pin
Pin
Name
Receiver
RX2Signal(-) ( RX2)
Power Ground
GND
Not connected NC
I2C Data
SDA
Receiver
RX1Signal(-) ( RX1)
Power Ground
GND
Not connected NC
Power Ground
GND
Receiver Signal(- RX0) ( RX0- )
Power Ground
GND
Not connected NC
Clock Signal(+) RXC+
(RXC+)
Analog red
RED
Analog blue
BLUE
Analog GND
GND
1
O O
3
5
7
9
O
O
O
O
11
13
15
17
O
O
O
O
Description
2
RX2+
Receiver Signal(+) ( RX2+ )
O
O
O
O
4
6
8
10
NC
SCL
NC
RX1+
Not connected
I2C clock
Not connected
Receiver Signal(+) ( RX1+ )
O
O
O
O
12
14
16
18
NC
+5V
HP
RX0+
Not connected
+5V from DVI video card
Hot Plug
Receiver Signal(+) ( RX0+ )
19
21
23
O O
O O
O O
20
22
24
NC
GND
RXC-
Not connected
Power Ground
Clock Signal(-) (RXC-)
C1
C3
C5
O O
O O
O O
C2
C4
C5
-1
GREEN
HSYNC
GND
Analog green
Horizontal sync
Analog GND
CRTtoLCD-51
01.02.2014
15
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.4
On Screen Display
With the self explaining OSD ( On Screen Display ) you can modify the
settings and control the special features of the CRTtoLCD-51. The OSD
uses a number of menus and submenus for making changes and turning
the special features on or off. The configuration can be done via the OSDkeypad (OSD-Panel-Kit).
To start the OSD press the “OSD” button on the keypad, after switching
the power supply on. If a valid flat panel configuration is installed, the
OSD Main Menu will be displayed.
To select an tab, simply use the button “UP” or ”DOWN” to move
cursor to the tab you want and press button “OSD”. When you use the
“Exit” and press the “CONFIRM”-button, the OSD will be closed.
To use a tab menu, simply use “OSD”-button to select the field.
Use “UP” or “DOWN” to select a value for that field. The “Exit”-field on
bottom-side on the tab will go up to the tab-selection. Simply press
“OSD”-button.
the
tab
the
the
Note: All changed values will only be saved by selecting “Exit” from the
OSD. If not, the adjusted values will be lost after loss of power.
CRTtoLCD-51
01.02.2014
16
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.5
Technical Specification
These values were measured with OSD-Panel attached and without flatpanel and backlight
inverter.
- Supply voltage at 25˚C without load:
Minimum supply voltage
Typical supply voltage
: + 11,4 V DC
: + 12,0 V DC
Absolute Maximum supply voltage : + 12.6 V DC
- Typical Input current at 25˚C without load:
CRTtoLCD-51 with input signal (XGA) : 250 mA
CRTtoLCD-51 with power down typical
: 60 mA
- Input Supply voltage ripple : typical 100 mV peak to peak 0 – 20 MHz
- Current Rating of Flatpanel Power supply:
PANEL VCC Steady State 3V / 5V and 12V @ +-5% : 3A
PANEL VCC 5sec. -5% 3V3 @4,33A
PANEL VCC 5sec. -5% 5V @ 4,15A
PANEL VCC 5sec. -2% 12V @ 4A
Note: Output power without any switch or short circuit breaker
- Slewrate of Flatpanel Power supply with 3A load
PANEL VCC 3V3 302us
PANEL VCC 5V 408us
PANEL VCC 12V 1.7ms
- Voltage and Current Rating of Backlight Power supply:
Direct +12V Output voltage without any switch or short circuit breaker
CN400: Maximum output current 4A
CN401: Maximum output current 2A
There are no limitations between Backlight Power and Flatpanel Power
The only limitation is the capability of the DC Input Power supply
VGA connector signals :
Sync input voltage low : 0.8 V
Sync input voltage high : 2.4 V
RGB input voltage
RGB input current
: 0 – 0.7 V with 75 Ohm external termination
: 0 – 5 mA
- Temperature : ambient
:
0˚ C – 60˚ C (*1)
Non operating : - 10˚ C – 85˚ C
(*1) The maximum temperature on the module surface can exceed above mentioned ambient
temperature. It is the user responsibility to keep this temperature within the above
specification.
- Thermal gradient : operating
: 25˚ C per hour
non-operating : 40˚ C per hour
- Relative Humidity : operating
: 10% - 90 % RH non-condensing
non operating : 5% - 95% RH non-condensing
CRTtoLCD-51
01.02.2014
17
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.5
Technical Specification
- Mechanical : Shock : 50G/20ms square wave maximum
Vibration : 1G/0-600Hz, dwell not to exceed
- Altitude : operating
: 0 – 3000 m
non-operating : 0 – 5000 m
- Dimensions of the printed circuit board :
Width:
114.28 mm
Length:
179.07 mm
Thickness:
1.50 mm
- Dimensions of the module :
Width:
119.50 mm
Length:
179.07 mm
Height:
16.50 mm +2mm (*)
Note : The dimension of the module can change if cable, Adapter or
Keypad plugged in!
CRTtoLCD-51
01.02.2014
18
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.6
Supported Video Modes (Analog Input)
Generally all VESA compatible video modes are supported. If modes are
not supported the controller displays “Invalid Mode” on the flat panel. In
this case use the Flat Panel Editor, available on request, to add this special
mode to the supported mode table.
Following modes are tested
Vertical refresh rate
Video Mode Input
720 x 400
640 x 350
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1600 x 1200
Mode standard
70 Hz
70 Hz
70 Hz
59,9 Hz
60 Hz
72 Hz
72,8 Hz
75 Hz
56,25 Hz
60 Hz
70 Hz
72 Hz
75 Hz
60 Hz
70 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
1.6
DOS
DOS
DOS
VGA
VGA
VGA
VGA
VGA
SVGA
SVGA
SVGA
SVGA
SVGA
XGA
XGA
XGA
XGA
SXGA
SXGA
SXGA
UXGA
Supported Video Modes (DVI Input)
Generally all VESA compatible video modes are supported. If modes are
not supported the controller displays “Invalid Mode” on the flat panel. In
this case use the Flat Panel Editor, available on request, to add this
special mode to the supported mode table.
Following modes are tested
Video Mode Input
640 x 480
800 x 600
1024 x 768
1280 x 1024
1200 x 1600
Vertical refresh rate
60
60
60
60
60
Hz
Hz
Hz
Hz
Hz
Mode standard
VGA
SVGA
XGA
SXGA
UXGA
CRTtoLCD-51
01.02.2014
19
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
1.7
Layout/Schematics
CRTtoLCD-51
CRTtoLCD-51
01.02.2014
20
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
OSD Keypad
1.8
OSD-Keypad “OSD-Panel“
Power ON/OFF LED
25 mm
120mm
Keypad JP1 connected to CN501 of CRTtoLCD-51!
CRTtoLCD-51
01.02.2014
21
eCOUNT Technology GmbH
Schatzbogen 60/62
D - 81829 München
Tel.: 0049 (0) 89 454571 - 0
Fax.: 0049 (0) 89 454571 - 11
Technical Support
1.9
Please report any errors or problems to this email address:
[email protected].
Normally, there is no telephone support. In your email message, please
include the following information :
Company Name
Your Name
Address
Email
Telephone/Fax
Exact description of the hardware, etc.
Exact description of the software used (for example: Win XP with
driver XYZ )
Exact description of the error.
Revision History
2.0
Date
01.02.2014
Author
H.Leipold
Version
1.0
Description
Initial release
CRTtoLCD-51
01.02.2014
22