ES2A THRU ES2J

SURFACE MOUNT SUPER FAST RECTIFIER
ES2A THRU ES2J
VOLTAGE RANGE
50 to 600Volts
CURRENT
2.0 Ampere
FEATURES
•
•
•
•
•
DO-214AA(SMB)
Plastic package has Underwrites Laboratory
Flammability Classification 94V-0
Glass passivated chip junction
Built-in strain relief
Super Fast switching speed for high efficiency
High temperature soldering guaranteed:
250℃/10 seconds
MECHANICAL DATA
•
•
•
•
Case: JEDED DO-214AA transfer molded plastic
Terminals: Solder plated, Solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Weight: 0.003 ounce, 0.093 gram
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
•
•
Ratings at 25℃ ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load derate current by 20%.
SYMBOLS ES2A
ES2B
Maximum Repetitive Peak Reverse Voltage
VRRM
50
100
Maximum RMS Voltage
VRMS
35
70
Maximum DC Blocking Voltage
VDC
50
100
Maximum Average Forward Rectified Current
at TL =100℃
Peak Forward Surge Current
8.3ms single half sine wave superimposed on
rated load (JEDEC method)
Maximum lnstantaneous Forward Voltage @ 2.0A
Maximum DC Reverse Current at
TA=25℃
rated DC Blocking voltage per
TA=125℃
element
Maximum Reverse Recovery Time
Test conditions IF=0.5A, IR=1.0A, IRR=0.25A
Typical Junstion Capacitance
(Measured at 1.0MHz and applied reverse voltage of 4.0V)
Typical Thermal Resistance (Note 1)
ES2C
150
105
150
ES2D
200
140
200
ES2E
300
210
300
ES2G
400
280
400
ES2J
600
420
600
UNIT
Volts
Volts
Volts
I(AV)
2.0
Amps
IFSM
50
Amps
VF
0.95
IR
trr
CJ
1.25
5.0
200
35
25
RθJA
RθJL
TJ
TSTG
75
17
(-55 to +150)
(-55 to +150)
Volts
µA
nS
208
Operating Junction Temperature Range
Storage Tempetature Rang
Notes:
1. Thermal resistance from Junction to ambient and from junction to lead mounted on P.C.B. with
0.3”×0.3”(8.0mm × 8.0mm) copper pad areas.
Web Site: www.hkmic.com
1.7
pF
℃/W
℃
℃
SURFACE MOUNT SUPER FAST RECTIFIER
ES2A THRU ES2J
VOLTAGE RANGE
50 to 600 Volts
CURRENT
2.0 Ampere
FIG.1-TYPICAL FORWARD CURRENT
FIG.2-MAXIMUM NON-REPETITIVE PEAK
DERATING CURVE
FORWARD SURGE CURRENT
PEAK FORWARD SURGE
3.0
1.0
Single Phase
Half Wave 60Hz
Resistive or
Inductive Load
0.375″(9.5mm) Lead Length
60
CURRENT, (A)
2.0
(A)
AVERAGE FORWARD CURRENT,
RATING AND CHRACTERISTIC CURVES ES2A THRU ES2J
8.3ms Single Half Sine-Wave
(JEDEC Method) TJ = T jmax
50
40
30
20
10
1 Cycle
0
0
25
100
75
50
175
150
125
0
1
4
2
AMBIENT TEMPERATURE, (° C)
6
8 10
40
20
60
100
NUMBER OF CYCLES AT 60 Hz
FIG.3-TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
FIG.4-TYPICAL REVERSE
CHARACTERISTICS
0.1
0.01
TJ=25° C
Pulse Width=300us
1% Duty Cycle
10
1.0
(μA)
INSTANTANEOUS REVERSE CURRENT,
2E
ES
ES
2J
ES
2A
-2D
-2G
1.0
(A)
INSTANTANEOUS FORWARD CURRENT,
10
TJ =100° C
0.1
TJ =25℃
0.01
0
0.001
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
20
40
60
80
100
120
140
PERCENT OF RATED PEAK
REVERSE VOLTAGE,(%)
INSTANTANEOUS FORWARD VOLTAGE,(V)
FIG.5-TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE,(pF)
100
ES 2A-E S2D
ES2E-ES 2J
F1G.6-TEST CIRCUIT DIAGRAM AND
REVERSE RECOVERY TIME CHARACTERISTIC
Trr
50Ω
10Ω
NONINDUCTIVE NONINDUCTIVE
+0.5A
(-)
10
(+)
25 Vdc
(approx.)
(-)
TJ =25° C
f=1MHz
Vsig=50mVp-p
1.0
1Ω
NON
INDUCTIVE
PULSE
GENERATIOR
(NOTE 2)
0
-0.25A
(+)
OSCILLOSCOPE
(NOTE 1)
-1.0A
1
0.1
D.U.T.
10
REVERSE VOLTAGE,(V)
100
NOTES : 1.Rise Time=7ns max. Input Impedance=
1 magohm. 22pF
2.Rise time=10ns max. Source Impedance=
50 ohms
Web Site: www.hkmic.com
1cm
SET TIME BASE FOR
50/100ns/cm