Series MC2 www.vishay.com Vishay Wet Tantalum Capacitor, Button Assembly or Array, All-Tantalum Case, - 55 °C to 125 °C Operation FEATURES • All-Tantalum electrodes eliminate silver migration • Withstands high ripple current • Long life reliability • Reverse voltage capability • Stackable PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 °C to + 125 °C Voltage Range: 6 VDC to 125 VDC Capacitance Range: 235 μF to 9100 μF SPECIFICATIONS Environmental Classification: 55/125/56 Vibration: 10 Hz to 2000 Hz, 0.75 mm or 99 m/s2, 30 h Bump: 320 m/s2, 4000 bumps INTRODUCTION The module series of capacitors comprise five individual button units which are connected in parallel to give a very high capacitance. The epoxy resin encapsulation within an epoxy resin box, measuring approx. 50 mm x 50 mm x 10 mm gives an extremely robust construction which lends itself to bank mounting. Shock: Acceleration: Low Air Pressure: 1 kPa REVERSE VOLTAGE CAPABILITY Module units are polar capacitors which allow the application of reverse potentials not exceeding 3 V at temperatures up to 125 °C. The MC module incorporated CA2 or CE2 style buttons. These button capacitor styles are of all-tantalum construction using a tantalum anode and tantalum cathode with a non-solid electrolyte. This well-proven construction with its highly efficient seal combined with the resin encapsulation gives an extremely robust module of long life and high reliability under military and avionic environments with the capability of withstanding 3 V in reverse, and of handling high levels of ripple current. SURGE VOLTAGE APPLICATIONS CAPACITANCE TOLERANCE These units are designed for use in general military, space avionics and professional applications. For example: Power supply smoothing, filter network, timer functions. The standard capacitance tolerance is ± 20 % although special tolerances are available by arrangement. The surge voltage capability is 115 % of the voltage rating at the relevant temperature. TEMPERATURE RANGE The capacitor is designed for operation between - 55 °C and + 125 °C, with linear voltage derating above + 85 °C to 66 % of the rated voltage at + 125 °C. WEIGHT The approximate weight of a module is 130 g. Revision: 15-May-12 Document Number: 42079 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series MC2 www.vishay.com Vishay APPLICATION INFORMATION ESTABLISHED FAILURE RATE Capacitors may be operated at less than the rated voltage, resulting in significantly reduced leakage current values. The MT range incorporates 735D capacitors which are structurally similar to and subjected to the same processes as our 135D and MIL-PRF-39006 range which is to an established failure rate of level R, 0.01 % per 1000 h at a 60 % confidence level. The CECC system of testing does not readily yield data to prove these levels, but in-house testing supports this figure. In timing circuits, or other applications where the device is subjected only to a DC voltage, the ballistic or DC capacitance will be somewhat larger than measured at 50 Hz. The parametric information must necessarily be brief, although additional comprehensive data is available on request, and the tests tailored to customers’ requirements can be made. Although failure rates derived from life tests are a useful guide, in practice capacitors rarely see conditions of a steady DC voltage and temperature. The construction of the MT module gives an ability to handle the high ripple currents at high frequencies, reverse voltages up to 3 V, and extremes of temperature likely to be encountered in modern circuitry. RELIABILITY All capacitors are subjected to burn-in. This is to remove infant mortalities and ensure reliability. The capacitor lifetime is enhanced when the unit is subjected to a reduced ripple current, a low ambient temperature, and is externally cooled. The use of a heat sink is recommended. ALTERNATIVE CONSTRUCTION Alternative constructions based on the module range with differing terminal configurations and capacitor combinations including series connected units are available. STACKING The units are suitable for stacking by use of through bolts. It is strongly recommended that a metal heat sink is used between each unit in order to eliminate the possibility of hot spots. ORDERING PROCEDURE Example: MC2D (910 μF, 75 VDC) Vishay Part Number: MC2D917M075S ORDERING INFORMATION MC2 D 917 M 075 S MODEL CASE CODE CAPACITANCE TOLERANCE VOLTAGE TERMINATION AND PACKAGING See Standard Ratings table. This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. M = 20 % (std) K = 10 % (special order) This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an “R” (6R3 = 6.3 V). S = Standard (Ag/Cu) DIMENSIONS in inches [millimeters] MC2 styles H B - + E dia. A C C L D A Actual size CASE CODE A max. H max. C crs. D crs. E dia. B min. B max. D 2.016 [51.2] 0.445 [11.3] 0.748 [19.0] 1.500 [38.1] 0.189 [4.8] 0.095 [2.41] 0.101 [2.56] Revision: 15-May-12 Document Number: 42079 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series MC2 www.vishay.com Vishay STANDARD RATINGS VISHAY PART NUMBERS CASE CODE CAPACITANCE AT 50 Hz (μF) MC2D608M006S D 6000 MC2D918M6R3S MC2D758M6R3S D D 9100 7500 MC2D508M008S D 5000 MC2D628M010S MC2D518M010S MC2D418M010S D D D 6200 5100 4100 MC2D348M015S D 3400 MC2D398M016S MC2D338M016S D D 3900 3300 MC2D288M020S MC2D248M020S MC2D208M020S D D D 2800 2350 1950 MC2D278M025S MC2D248M025S D D 2700 2400 MC2D178M030S MC2D148M030S D D 1650 1350 MC2D208M040S MC2D168M040S MC2D138M040S D D D 2000 1600 1300 MC2D118M050S MC2D907M050S MC2D757M050S D D D 1100 900 750 MC2D118M063S D 1100 MC2D917M075S MC2D757M075S MC2D607M075S MC2D507M075S MC2D417M075S D D D D D 910 750 600 500 410 MC2D627M100S MC2D477M100S MC2D287M100S D D D 620 470 280 MC2D397M125S MC2D247M125S D D 390 235 DISSIPATION FACTOR AT 50 Hz (%) 25 °C 125 °C IMPEDANCE AT 100 kHz () 25 °C - 55 °C 6 VDC AT 85 °C; 4 VDC AT 125 °C 75.0 95.0 0.6 3 6.3 VDC AT 85 °C; 4 VDC AT 125 °C 85.0 108.0 0.6 9 80.0 101.0 0.6 9 8 VDC AT 85 °C; 5.3 VDC AT 125 °C 65.0 85.0 0.6 3 10 VDC AT 85 °C; 6.6 VDC AT 125 °C 75.0 95.0 0.6 9 65.0 83.0 0.6 9 55.0 70.0 0.6 3 15 VDC AT 85 °C; 10 VDC AT 125 °C 45.0 55.0 0.6 3 16 VDC AT 85 °C; 10 VDC AT 125 °C 60.0 76.0 0.6 9 45.0 57.0 0.6 9 20 VDC AT 85 °C; 13.4 VDC AT 125 °C 35.0 45.0 0.6 3 30.0 40.0 0.6 3 25.0 30.0 0.6 3 25 VDC AT 85 °C; 16 VDC AT 125 °C 40.0 50.0 0.6 9 35.0 44.0 0.6 9 30 VDC AT 85 °C; 20 VDC AT 125 °C 20.0 25.0 0.6 3 17.0 20.0 0.6 3 40 VDC AT 85 °C; 25 VDC AT 125 °C 30.0 38.0 0.6 9 22.0 28.0 0.6 9 18.0 23.0 0.6 9 50 VDC AT 85 °C; 33.3 VDC AT 125 °C 14.0 18.0 0.6 3 11.5 15.0 0.6 3 9.5 12.0 0.6 3 63 VDC AT 85 °C; 40 VDC AT 125 °C 15.0 19.0 0.6 9 75 VDC AT 85 °C; 50 VDC AT 125 °C 13.0 16.5 0.6 9 11.0 14.0 0.6 9 7.5 10.0 0.6 3 7.0 9.0 0.6 3 5.5 7.0 0.6 3 100 VDC AT 85 °C; 66.7 VDC AT 125 °C 9.0 11.0 0.6 9 7.5 9.5 0.6 9 3.5 4.5 0.6 3 125 VDC AT 85 °C; 83.3 VDC AT 125 °C 7.0 9.0 0.6 9 3.0 4.0 0.6 3 MAX. DCL (μA) C AT 50 Hz (%) 25 °C 125 °C - 55 °C 125 °C 75 250 - 80.0 25.0 75 75 250 250 - 80.0 - 80.0 30.0 30.0 50 250 - 75.0 25.0 75 50 50 250 250 250 - 80.0 - 80.0 - 70.0 30.0 30.0 20.0 40 250 - 65.0 20.0 50 40 250 250 - 75.0 - 70.0 25.0 25.0 25 25 25 250 250 250 - 60.0 - 55.0 - 50.0 15.0 15.0 15.0 25 25 250 250 - 65.0 - 60.0 20.0 20.0 25 25 250 250 - 50.0 - 45.0 10.0 10.0 25 25 25 250 250 250 - 55.0 - 50.0 - 50.0 20.0 12.5 12.5 15 15 15 250 250 250 - 40.0 - 35.0 - 30.0 10.0 10.0 10.0 20 250 - 45.0 12.5 20 20 15 15 15 250 250 250 250 250 - 40.0 - 35.0 - 25.0 - 20.0 - 17.5 12.5 12.5 7.5 7.5 7.5 20 20 15 250 250 250 - 28.0 - 22.0 - 12.5 10.0 10.0 7.5 20 15 250 250 - 20.0 - 10.0 10.0 7.5 Notes • Capacitance tolerance: M = 20 % standard K = 10 % special order • Termination type: S = Standard Revision: 15-May-12 Document Number: 42079 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series MC2 www.vishay.com Vishay PERFORMANCE CURVES Capacitance/temperature at 50 Hz Dissipation factor/temperature at 50 Hz 200 1 2 3 4 Percentage of capacitance (%) ( 25 °C standard) 120 80 1= 2= 3= 4= 160 Dissipation factor (%) 100 1 2 9100 µF, 6.3 V 6000 µF, 6 V 390 µF, 125 V 235 µF, 125 V 120 60 40 1 2 3 4 20 0 - 60 - 40 - 20 0 20 40 60 = = = = 9100 µF, 6.3 V 6000 µF, 6 V 390 µF, 125 V 235 µF, 125 V 80 100 80 3 40 4 0 - 60 120 140 (°C) Impedance/temperature at 50 Hz - 40 - 20 0 20 40 60 80 100 120 140 (°C) Leakage current/temperature at maximum voltage 100 9100 µF, 6.3 V 6000 µF, 6 V Impedance (Ω) 235 µF, 125 V 10 390 µF, 125 V 3400 µF, 15 V 1 Leakage current (µA) 80 9100 µF, 6.3 V 6000 µF, 6 V 0.1 - 60 - 40 - 20 0 20 40 60 80 100 60 40 20 235 µF, 125 V 390 µF, 125 V 0 - 60 120 140 (°C) - 40 Capacitance/frequency at 25 °C 0 20 40 60 80 100 120 140 (°C) ESR/frequency at 25 °C 120 0.30 100 0.25 3 80 60 2 40 20 0.20 1 ESR (Ω) Percentage of 50 Hz capacitance - 20 4 0.15 0.10 1 = 235 µF, 125 V 2 = 390 µF, 125 V 3 = 3400 µF, 15 V 4 = 6000 µF, 6 V 5 = 9100 µF, 6.3 V 3 4 5 0 101 Revision: 15-May-12 102 103 104 f (Hz) 0.05 0 101 1 1= 2= 3= 4= 390 µF, 125 V 235 µF, 125 V 9100 µF, 6.3 V 6000 µF, 6 V 102 2 103 104 f (Hz) 105 Document Number: 42079 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series MC2 www.vishay.com Vishay PERFORMANCE CURVES Impedance/frequency at 25 °C Impedance (Ω) 10 1 1 = 235 µF, 125 V 2 = 390 µF, 125 V 3 = 3400 µF, 15 V 4 = 6000 µF, 6 V 5 = 9100 µF, 6.3 V 1 2 3 4 5 0.1 0 102 103 104 105 f (Hz) 106 Note • All performance curves are provided from historic Arcotronics module series M/ME datasheet information CROSS REFERENCE VISHAY PART NUMBER MC2D397M125S MC2D247M125S MC2D627M100S MC2D477M100S MC2D287M100S MC2D917M075S MC2D757M075S MC2D607M075S MC2D507M075S MC2D417M075S MC2D118M063S MC2D118M050S MC2D907M050S MC2D757M050S MC2D208M040S MC2D168M040S MC2D138M040S MC2D178M030S MC2D148M030S MC2D278M025S MC2D248M025S MC2D288M020S MC2D248M020S MC2D208M020S MC2D398M016S MC2D338M016S MC2D348M015S MC2D628M010S MC2D518M010S MC2D418M010S MC2D508M008S MC2D918M6R3S MC2D758M6R3S MC2D608M006S Revision: 15-May-12 ARCOTRONICS PART NUMBER 402/1/50165/023 402/1/50165/003 402/1/50165/025 402/1/50165/024 402/1/50165/004 402/1/50165/027 402/1/50165/026 402/1/50165/008 402/1/50165/007 402/1/50165/006 402/1/50165/028 402/1/50165/011 402/1/50165/010 402/1/50165/009 402/1/50165/031 402/1/50165/030 402/1/50165/029 402/1/50165/013 402/1/50165/012 402/1/50165/033 402/1/50165/032 402/1/50165/016 402/1/50165/015 402/1/50165/014 402/1/50165/035 402/1/50165/034 402/1/50165/017 402/1/50165/037 402/1/50165/036 402/1/50165/018 402/1/50165/019 402/1/50165/039 402/1/50165/038 402/1/50165/020 KEMET PART NUMBER T298E397M125AU T298M237M125AU T298E627M100AU T298E477M100AU T298M287M100AU T298E917M075AU T298E757M075AU T298M607M075AU T298M507M075AU T298M417M075AU T298E118M063AU T298M118M050AU T298M907M050AU T298M757M050AU T298E208M040AU T298E168M040AU T298E138M040AU T298M168M030AU T298M138M030AU T298E278M025AU T298E248M025AU T298M288M020AU T298M238M020AU T298M198M020AU T298E398M016AU T298E338M016AU T298M348M015AU T298E628M010AU T298E518M010AU T298M418M010AU T298M508M008AU T298E918M006AU T298E758M006AU T298M608M006AU Document Number: 42079 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000